Resources
In a physics laboratory experiment, a student determines the specific heat capacity of an unknown cylindrical metal specimen using a dual-cup calorimeter. The inner cup has a mass of and is made of copper (). The cup contains of deionized water (). A digital probe records an initial stable water/cup temperature of . The metal specimen of mass is heated in a boiling water bath at an atmospheric pressure corresponding to a boiling point of . After rapid transfer with negligible water carryover, the mixture is gently stirred until the temperature log peaks at . Calculate the specific heat capacity of the specimen and identify whether the specimen is more likely zinc () or iron ().
Answer and steps
Final answer
; closest to zinc ( with an experimental deviation)
Steps
Principle of Conservation of Energy
In an isolated calorimeter, assuming negligible heat loss to the surrounding environment and the thermometer/stirrer, the heat lost by the hot specimen equals the heat gained by the cooler water and copper cup:
For each substance undergoing a temperature change without a phase transition, heat transferred is given by .
Identify Given Values and Temperature Changes
-
Specimen:
- Mass:
- Initial temperature:
- Final temperature:
- Temperature decrease:
-
Water:
- Mass:
- Specific heat capacity:
- Initial temperature:
- Temperature increase:
-
Copper Cup:
- Mass:
- Specific heat capacity:
- Temperature increase:
Calculate Heat Gained by the Water and Cup
- Heat absorbed by the water:
- Heat absorbed by the copper cup:
- Total heat gained:
Calculate the Specific Heat Capacity of the Specimen
The heat lost by the metal specimen is:
Setting :
Rounding to three significant figures gives:
Identification of the Metal
Compare the experimental result with the accepted reference values:
- Zinc:
- Iron:
The specimen is significantly closer to zinc () with an experimental deviation.
Typical errors
01 The student forgets to include the heat capacity of the calorimeter cup, leading to an underestimated heat transfer and calculated specific heat capacity.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You omitted the heat absorbed by the inner copper cup. Because the cup starts at the initial water temperature and warms up alongside the water to , it also absorbs heat: .
- Step 4Correct
Your algebraic isolation of was executed properly, but the numerical result is too low due to omitting .
- Step 5
,
Correct,
Your comparison logic is sound and yields the correct conclusion (zinc), although the difference values carry forward your previous calculation error.
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated both temperature changes ( and ) accurately.
You correctly used the specific heat formula for the water.
You correctly set up the comparison to identify which metal was closer to your calculated value.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the specimen's lost heat solely to the heat gained by water, neglecting the copper container holding the water.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIn calorimetry problems, any component in direct thermal contact with the liquid (such as the inner cup or stirrer) is part of the absorbing system and undergoes the exact same temperature change as the water.
REASONING PATH
Your ACEpath teacher’s suggested approach- System Boundary Check
Every component that changes temperature during mixing must appear in the energy conservation equation: .
Check the problem statement for given masses and specific heat capacities of containers, stirrers, or the calorimeter vessel, and add a term for each.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the heat absorbed by the copper cup: .
Find total heat gained: .
Equate to heat lost by the specimen: .
Solve for : .
; the specimen is more likely zinc.
02 The student assumes boiling water is at exactly 100.0°C instead of using the given ambient boiling point of 99.6°C, slightly overestimating the specimen's temperature drop.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You assumed the initial temperature of the boiling water bath was , but the problem stated that atmospheric pressure set the boiling point at .
- Step 3Correct
Your formula and algebra were executed properly, but substituting instead of caused your value for to be slightly low.
- Step 4
, The specimen is more likely zinc.
WHAT YOU DID WELL
Compliments from Your TeacherYou included both the water and the calorimeter cup in your heat balance equation.
You correctly calculated the temperature change for the calorimeter contents.
You correctly identified the metal by comparing absolute differences.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the nominal boiling point instead of the problem's given value of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisRelying on memorized default constants (such as water boiling at ) rather than extracting the exact local ambient parameters provided in the problem description.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check environmental parameters
Atmospheric pressure shifts the boiling point of liquids; always use the measured local boiling point when provided.
Scan the problem text for ambient or measured initial conditions before substituting standard nominal constants.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the true temperature drop: .
Solve for the specific heat: .
Check deviation against zinc: .
; the specimen is more likely zinc.
03 The student inverts the heat balance equation or uses the initial water temperature instead of the final equilibrium temperature for the metal's temperature change, calculating ΔT_s as 99.6°C - 21.4°C.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The hot metal specimen cools down until it reaches the final mixture equilibrium temperature (), not the initial cold water temperature ().
- Step 3Correct
Because your was too large ( instead of ), your resulting specific heat capacity was calculated as instead of .
- Step 4Correct
Although your qualitative identification happened to be correct because zinc was still closer, the comparison was based on the inaccurate specific heat value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly combined the heat capacities of the water and the copper calorimeter cup.
You used the conservation of energy principle with the proper algebraic structure.
You correctly compared the experimental result to the standard values using absolute differences.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeUsing the initial temperature of the cold reservoir instead of the common final equilibrium temperature for the hot object's temperature change.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the initial condition of the cold substance () with the common final temperature of the entire system (). In calorimetry, all interacting substances stop exchanging heat once they reach the shared final equilibrium temperature . Therefore, the hot object cools from to , never to the cold reservoir's initial temperature.
REASONING PATH
Your ACEpath teacher’s suggested approach- Final Equilibrium Temperature
In an isolated mixture, all components reach the exact same final temperature .
Always write down the temperature interval for the hot body as before plugging numbers into the heat formula.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the correct temperature decrease of the specimen: .
Equate heat lost to heat gained: .
Solve for : .
; closest to zinc
Lock it in
In a calorimetry experiment, what thermal components constitute when hot metal is placed in water inside a metal cup?
. The cup also absorbs heat from the metal.
Similar question
An aluminum cup of mass () contains of water () at . A hot object is dropped in, raising the temperature of both the water and cup to . What is the total heat absorbed by the cup-water system?
Answer
. Key steps: ; ; ; .
A metal sample at is placed into a brass calorimeter () containing of water () at . The final equilibrium temperature is . Find the specific heat capacity of the metal.
Answer
. Key steps: ; ; ; .
A calorimeter consists of an inner vessel with an effective heat capacity holding of an unknown liquid. A lead cylinder () at is added. The temperature rises from to . Determine the specific heat capacity of the unknown liquid.
Answer
. Key steps: , ; ; ; ; .