Resources

A miniature laboratory AC generator consists of a rotor loop with area A=45.0 cm2A = 45.0\text{ cm}^2 and Ng=500 turnsN_g = 500\text{ turns} rotating at 1800 rev/min1800\text{ rev/min} in a magnetic field of B=85.0 mTB = 85.0\text{ mT}. The output is routed through a compact high-frequency step-up transformer whose primary has Np=120 turnsN_p = 120\text{ turns} and secondary has Ns=4.80×103 turnsN_s = 4.80 \times 10^3\text{ turns}. The secondary circuit is loaded with an impedance consuming a current expressed in milliamperes as Is,rms=17.5 mAI_{s,\text{rms}} = 17.5\text{ mA}. (a) Convert all parameters to standard SI base units and compute the peak open-circuit voltage E0\mathcal{E}_0 of the generator in volts. (b) Find the rms power delivered to the secondary load in milliwatts (mW\text{mW}) assuming unity power factor.

Answer and steps

Final answer

(a) E0=36.0 V\mathcal{E}_0 = 36.0\text{ V}; (b) Ps=1.78×104 mWP_s = 1.78 \times 10^4\text{ mW} (17.8 W17.8\text{ W})

Steps

Part (a): Conversion to SI Units and Peak Induced EMF

  1. Convert the given quantities into SI base units:

    • Loop area: A=45.0 cm2=45.0×10−4 m2=4.50×10−3 m2A = 45.0\text{ cm}^2 = 45.0 \times 10^{-4}\text{ m}^2 = 4.50 \times 10^{-3}\text{ m}^2
    • Magnetic field: B=85.0 mT=85.0×10−3 T=0.0850 TB = 85.0\text{ mT} = 85.0 \times 10^{-3}\text{ T} = 0.0850\text{ T}
    • Angular frequency ω\omega: ω=1800 rev/min×2π rad1 rev×1 min60 s=60π rad/s≈188.5 rad/s\omega = 1800\text{ rev/min} \times \frac{2\pi\text{ rad}}{1\text{ rev}} \times \frac{1\text{ min}}{60\text{ s}} = 60\pi\text{ rad/s} \approx 188.5\text{ rad/s}
    • Number of turns in the generator rotor: Ng=500 turnsN_g = 500\text{ turns}.
  2. Calculate the peak open-circuit EMF (E0\mathcal{E}_0): According to Faraday's law of electromagnetic induction, the instantaneous EMF produced by a rotating coil in a uniform magnetic field is: E(t)=E0sin⁡(ωt)\mathcal{E}(t) = \mathcal{E}_0 \sin(\omega t) where the peak EMF E0\mathcal{E}_0 is given by: E0=NgBAω\mathcal{E}_0 = N_g B A \omega

    Substituting the values: E0=500⋅(0.0850 T)⋅(4.50×10−3 m2)⋅(60π rad/s)≈36.05 V≈36.0 V\mathcal{E}_0 = 500 \cdot (0.0850\text{ T}) \cdot (4.50 \times 10^{-3}\text{ m}^2) \cdot (60\pi\text{ rad/s}) \approx 36.05\text{ V} \approx 36.0\text{ V}


Part (b): RMS Power Delivered to the Secondary Load

  1. Determine the primary RMS voltage (Vp,rmsV_{p,\text{rms}}): For a sinusoidal output, the root-mean-square voltage delivered by the generator to the transformer primary is: Vp,rms=E02=36.05 V2≈25.49 VV_{p,\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} = \frac{36.05\text{ V}}{\sqrt{2}} \approx 25.49\text{ V}
  2. Determine the secondary RMS voltage (Vs,rmsV_{s,\text{rms}}): Using the ideal transformer turns-ratio equation: Vs,rmsVp,rms=NsNp\frac{V_{s,\text{rms}}}{V_{p,\text{rms}}} = \frac{N_s}{N_p} Given Np=120 turnsN_p = 120\text{ turns} and Ns=4.80×103 turnsN_s = 4.80 \times 10^3\text{ turns}: NsNp=4800120=40\frac{N_s}{N_p} = \frac{4800}{120} = 40 Vs,rms=40⋅Vp,rms=40⋅25.49 V≈1019.7 VV_{s,\text{rms}} = 40 \cdot V_{p,\text{rms}} = 40 \cdot 25.49\text{ V} \approx 1019.7\text{ V}
  3. Compute the RMS power delivered to the load (PsP_s): With a unity power factor (cos⁡ϕ=1\cos\phi = 1) and given Is,rms=17.5 mA=17.5×10−3 AI_{s,\text{rms}} = 17.5\text{ mA} = 17.5 \times 10^{-3}\text{ A}: Ps=Vs,rms⋅Is,rms⋅cos⁡ϕP_s = V_{s,\text{rms}} \cdot I_{s,\text{rms}} \cdot \cos\phi Ps=(1019.7 V)⋅(17.5×10−3 A)⋅1≈17.84 WP_s = (1019.7\text{ V}) \cdot (17.5 \times 10^{-3}\text{ A}) \cdot 1 \approx 17.84\text{ W}

    Converting to milliwatts (mW\text{mW}): Ps≈1.78×104 mW(17.8 W)P_s \approx 1.78 \times 10^4\text{ mW}\quad (17.8\text{ W})

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student converts rotational speed using frequency in Hz instead of angular velocity in rad/s by omitting the factor of 2π.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=4.50×10−3 m2A = 4.50 \times 10^{-3}\text{ m}^2, B=0.0850 TB = 0.0850\text{ T}

  2. Step 2

    ω=180060=30 rad/s\omega = \frac{1800}{60} = 30\text{ rad/s}

    Correct

    ω=1800 rev/min×2π rad1 rev×1 min60 s=60π rad/s≈188.5 rad/s\omega = 1800\text{ rev/min} \times \frac{2\pi\text{ rad}}{1\text{ rev}} \times \frac{1\text{ min}}{60\text{ s}} = 60\pi\text{ rad/s} \approx 188.5\text{ rad/s}

    Dividing 1800 rev/min1800\text{ rev/min} by 60 s/min60\text{ s/min} yields the rotational frequency in revolutions per second (f=30 rev/s=30 Hzf = 30\text{ rev/s} = 30\text{ Hz}). To find angular velocity ω\omega in radians per second, you must multiply by 2π rad/rev2\pi\text{ rad/rev}.

  3. Step 3

    E0=NgBAω=500×0.0850×4.50×10−3×30=5.74 VE_0 = N_g B A \omega = 500 \times 0.0850 \times 4.50 \times 10^{-3} \times 30 = 5.74\text{ V}

    Correct

    E0=NgBAω=500×0.0850×(4.50×10−3)×60π≈36.0 V\mathcal{E}_0 = N_g B A \omega = 500 \times 0.0850 \times (4.50 \times 10^{-3}) \times 60\pi \approx 36.0\text{ V}

    Your formula for peak induced EMF is correct, but evaluating with the incorrect ω\omega gives 5.74 V5.74\text{ V} instead of 36.0 V36.0\text{ V}.

  4. Step 4

    Erms=5.742=4.06 V  ⟹  Vs,rms=(4800120)×4.06=162.4 VE_{\text{rms}} = \frac{5.74}{\sqrt{2}} = 4.06\text{ V} \implies V_{s,\text{rms}} = \left(\frac{4800}{120}\right) \times 4.06 = 162.4\text{ V}

    Correct

    Vp,rms=36.052≈25.49 V  ⟹  Vs,rms=40×25.49 V≈1020 VV_{p,\text{rms}} = \frac{36.05}{\sqrt{2}} \approx 25.49\text{ V} \implies V_{s,\text{rms}} = 40 \times 25.49\text{ V} \approx 1020\text{ V}

    You correctly applied the RMS relationship Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}} and the ideal transformer ratio VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p}, but the result reflects the earlier ω\omega error.

  5. Step 5

    Prms=162.4×0.0175=2.84 W=2840 mWP_{\text{rms}} = 162.4 \times 0.0175 = 2.84\text{ W} = 2840\text{ mW}

    Correct

    Ps=Vs,rmsIs,rms=(1019.7 V)×(17.5×10−3 A)≈17.8 W=1.78×104 mWP_s = V_{s,\text{rms}} I_{s,\text{rms}} = (1019.7\text{ V}) \times (17.5 \times 10^{-3}\text{ A}) \approx 17.8\text{ W} = 1.78 \times 10^4\text{ mW}

    You correctly computed electric power with unity power factor (P=VrmsIrmsP = V_{\text{rms}} I_{\text{rms}}), but the final numerical value propagated the missing 2π2\pi factor.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted centimeters squared to meters squared and milliteslas to teslas.

You correctly identified and applied the peak EMF formula E0=NBAω\mathcal{E}_0 = N B A \omega.

You correctly related peak voltage to RMS voltage using the factor of 2\sqrt{2}.

You applied the transformer turns ratio equation and calculated load power accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angular velocity vs rotational frequency confusion

Omitting the 2π2\pi factor when converting rotational speed from rev/min\text{rev/min} (rpm) to angular frequency ω\omega in rad/s\text{rad/s}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating rotational frequency ff (measured in revolutions per second or Hz\text{Hz}) with angular speed ω\omega (measured in radians per second, rad/s\text{rad/s}). A complete revolution sweeps out an angle of 2π radians2\pi\text{ radians}, so ω=2πf\omega = 2\pi f.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Conversion for Rotational Motion
  • 1 rev=2π rad1\text{ rev} = 2\pi\text{ rad} and 1 min=60 s1\text{ min} = 60\text{ s}, leading to ω=rpm×2π60\omega = \text{rpm} \times \frac{2\pi}{60}.

  • Always write out unit factors explicitly: multiply by 2π rad1 rev\frac{2\pi\text{ rad}}{1\text{ rev}} and 1 min60 s\frac{1\text{ min}}{60\text{ s}} rather than just dividing by 6060.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ω=1800 rev/min×2π rad1 rev×1 min60 s=60π rad/s≈188.5 rad/s\omega = 1800\text{ rev/min} \times \frac{2\pi\text{ rad}}{1\text{ rev}} \times \frac{1\text{ min}}{60\text{ s}} = 60\pi\text{ rad/s} \approx 188.5\text{ rad/s}

  2. E0=500×0.0850 T×4.50×10−3 m2×60π rad/s≈36.05 V≈36.0 V\mathcal{E}_0 = 500 \times 0.0850\text{ T} \times 4.50 \times 10^{-3}\text{ m}^2 \times 60\pi\text{ rad/s} \approx 36.05\text{ V} \approx 36.0\text{ V}

  3. Vp,rms=36.05 V2≈25.49 VV_{p,\text{rms}} = \frac{36.05\text{ V}}{\sqrt{2}} \approx 25.49\text{ V}

  4. Vs,rms=4800120×25.49 V=40×25.49 V≈1019.7 VV_{s,\text{rms}} = \frac{4800}{120} \times 25.49\text{ V} = 40 \times 25.49\text{ V} \approx 1019.7\text{ V}

  5. Ps=(1019.7 V)×(17.5×10−3 A)≈17.84 W=1.78×104 mWP_s = (1019.7\text{ V}) \times (17.5 \times 10^{-3}\text{ A}) \approx 17.84\text{ W} = 1.78 \times 10^4\text{ mW}

Final answer

(a) E0=36.0 V\mathcal{E}_0 = 36.0\text{ V}; (b) Ps=1.78×104 mWP_s = 1.78 \times 10^4\text{ mW} (17.8 W17.8\text{ W})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting rotational speeds given in rpm or Hz directly to angular velocity ω\omega in rad/s\text{rad/s} using unit-factor cancellation.

  • Double-check whether formulas involving harmonic oscillation or rotation require cyclical frequency ff or angular frequency ω\omega before substituting values.

OverviewACEpath Teacher's Diagnosis

02 The student treats the peak voltage directly as the rms voltage when applying the transformer equation and calculating power.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=4.50×10−3 m2  ⟹  B=0.0850 T  ⟹  ω=1800×2π60=188.5 rad/sA = 4.50 \times 10^{-3}\text{ m}^2 \implies B = 0.0850\text{ T} \implies \omega = 1800 \times \frac{2\pi}{60} = 188.5\text{ rad/s}

  2. Step 2

    E0=500×0.0850×4.50×10−3×188.5=36.1 V\mathcal{E}_0 = 500 \times 0.0850 \times 4.50 \times 10^{-3} \times 188.5 = 36.1\text{ V}

  3. Step 3

    Vs=4800120×36.1=1444 VV_s = \frac{4800}{120} \times 36.1 = 1444\text{ V}

    Correct

    Vp,rms=E02≈25.49 V  ⟹  Vs,rms=NsNpVp,rms=40×25.49 V≈1020 VV_{p,\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} \approx 25.49\text{ V} \implies V_{s,\text{rms}} = \frac{N_s}{N_p} V_{p,\text{rms}} = 40 \times 25.49\text{ V} \approx 1020\text{ V}

    You substituted the peak voltage E0=36.1 V\mathcal{E}_0 = 36.1\text{ V} directly into the transformer turns-ratio equation instead of converting it to the rms primary voltage Vp,rms=E02V_{p,\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}}. This gave the peak secondary voltage (1444 V1444\text{ V}) rather than the rms secondary voltage (1020 V1020\text{ V}).

  4. Step 4

    Prms=1444×17.5×10−3=25.3 W  ⟹  Prms=25300 mWP_{\text{rms}} = 1444 \times 17.5 \times 10^{-3} = 25.3\text{ W} \implies P_{\text{rms}} = 25300\text{ mW}

    Correct

    Ps=Vs,rmsIs,rms=(1019.7 V)(17.5×10−3 A)≈17.8 W=1.78×104 mWP_s = V_{s,\text{rms}} I_{s,\text{rms}} = (1019.7\text{ V})(17.5 \times 10^{-3}\text{ A}) \approx 17.8\text{ W} = 1.78 \times 10^4\text{ mW}

    You correctly multiplied voltage by current and converted watts to milliwatts, but your result inherited the unscaled peak voltage from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately converted all given parameters into standard SI units.

You correctly applied E0=NBAω\mathcal{E}_0 = N B A \omega to determine the peak induced EMF.

You correctly identified the transformer turns ratio NsNp=40\frac{N_s}{N_p} = 40.

You correctly applied the power formula P=VIP = V I for a circuit with unity power factor.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating peak and rms quantities in AC circuits

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the peak voltage output E0\mathcal{E}_0 as an rms value. In sinusoidal AC circuits, average or rms power calculations require matching rms voltage with rms current (Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}}), or including an explicit factor of 12\frac{1}{2} when combining peak amplitudes.

REASONING PATH
Your ACEpath teacher’s suggested approach
Peak vs. RMS Conversion
  • For a sinusoidal AC signal, Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}} and Irms=I02I_{\text{rms}} = \frac{I_0}{\sqrt{2}}.

  • Before using voltages or currents in AC power formulas with given rms values, check whether each quantity is peak or rms and convert accordingly.

Consistent Power Calculation
  • Average/RMS electrical power is given by P=VrmsIrmscos⁡ϕ=12V0I0cos⁡ϕP = V_{\text{rms}} I_{\text{rms}} \cos\phi = \frac{1}{2} V_0 I_0 \cos\phi.

  • Never multiply a peak voltage directly by an rms current to find rms power; convert both to rms first.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the generator's peak voltage to rms voltage: Vp,rms=E02=36.05 V2≈25.49 VV_{p,\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} = \frac{36.05\text{ V}}{\sqrt{2}} \approx 25.49\text{ V}.

  2. Apply the transformer turns ratio to find the secondary rms voltage: Vs,rms=NsNpVp,rms=40×25.49 V≈1020 VV_{s,\text{rms}} = \frac{N_s}{N_p} V_{p,\text{rms}} = 40 \times 25.49\text{ V} \approx 1020\text{ V}.

  3. Calculate the secondary rms power using the given Is,rms=17.5 mAI_{s,\text{rms}} = 17.5\text{ mA}: Ps=Vs,rmsIs,rms=(1019.7 V)(17.5×10−3 A)≈17.84 WP_s = V_{s,\text{rms}} I_{s,\text{rms}} = (1019.7\text{ V})(17.5 \times 10^{-3}\text{ A}) \approx 17.84\text{ W}.

  4. Convert the power to milliwatts: Ps=17.84×103 mW≈1.78×104 mWP_s = 17.84 \times 10^3\text{ mW} \approx 1.78 \times 10^4\text{ mW}.

Final answer

(a) E0=36.0 V\mathcal{E}_0 = 36.0\text{ V}; (b) Ps=1.78×104 mWP_s = 1.78 \times 10^4\text{ mW} (17.8 W17.8\text{ W})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice explicitly writing subscripts such as V0V_0 (peak) versus VrmsV_{\text{rms}} at the start of AC circuit problems.

  • Verify that power formulas consistently pair peak with peak (P=12V0I0P = \frac{1}{2}V_0 I_0) or rms with rms (P=VrmsIrmsP = V_{\text{rms}} I_{\text{rms}}).

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly converts area from square centimeters to square meters using 10⁻² instead of 10⁻⁴.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=45.0×10−2 m2=0.450 m2  ⟹  B=0.0850 T  ⟹  ω=1800×2π60=188.5 rad/sA = 45.0 \times 10^{-2}\text{ m}^2 = 0.450\text{ m}^2 \implies B = 0.0850\text{ T} \implies \omega = \frac{1800 \times 2\pi}{60} = 188.5\text{ rad/s}

    Correct

    A=45.0 cm2=45.0×(10−2 m)2=4.50×10−3 m2A = 45.0\text{ cm}^2 = 45.0 \times (10^{-2}\text{ m})^2 = 4.50 \times 10^{-3}\text{ m}^2

    You converted the magnetic field and angular velocity perfectly, but square centimeters convert to square meters by multiplying by (10−2)2=10−4(10^{-2})^2 = 10^{-4}, giving 4.50×10−3 m24.50 \times 10^{-3}\text{ m}^2 rather than 0.450 m20.450\text{ m}^2.

  2. Step 2

    E0=500×0.0850×0.450×188.5=3605 VE_0 = 500 \times 0.0850 \times 0.450 \times 188.5 = 3605\text{ V}

    Correct

    E0=NgBAω=500×0.0850 T×4.50×10−3 m2×188.5 rad/s≈36.0 V\mathcal{E}_0 = N_g B A \omega = 500 \times 0.0850\text{ T} \times 4.50 \times 10^{-3}\text{ m}^2 \times 188.5\text{ rad/s} \approx 36.0\text{ V}

    Your formula for the peak induced EMF (E0=NBAω\mathcal{E}_0 = N B A \omega) is entirely correct, but the result is 100 times too large because it propagated the incorrect coil area.

  3. Step 3

    Erms=36052=2549 VE_{\text{rms}} = \frac{3605}{\sqrt{2}} = 2549\text{ V}

    Correct

    Vp,rms=E02=36.05 V2≈25.49 VV_{p,\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} = \frac{36.05\text{ V}}{\sqrt{2}} \approx 25.49\text{ V}

    You correctly applied the relation between peak and rms values for a sinusoidal voltage.

  4. Step 4

    Vs,rms=(4800120)×2549=101960 VV_{s,\text{rms}} = \left(\frac{4800}{120}\right) \times 2549 = 101960\text{ V}

    Correct

    Vs,rms=NsNpVp,rms=(4800120)×25.49 V≈1020 VV_{s,\text{rms}} = \frac{N_s}{N_p} V_{p,\text{rms}} = \left(\frac{4800}{120}\right) \times 25.49\text{ V} \approx 1020\text{ V}

    You applied the ideal transformer voltage ratio equation correctly.

  5. Step 5

    Prms=101960×0.0175=1784 W=1.78×106 mWP_{\text{rms}} = 101960 \times 0.0175 = 1784\text{ W} = 1.78 \times 10^6\text{ mW}

    Correct

    Ps=Vs,rmsIs,rms=1019.7 V×1.75×10−2 A≈17.84 W=1.78×104 mWP_s = V_{s,\text{rms}} I_{s,\text{rms}} = 1019.7\text{ V} \times 1.75 \times 10^{-2}\text{ A} \approx 17.84\text{ W} = 1.78 \times 10^4\text{ mW}

    You correctly computed power from RMS voltage and current and handled the prefix conversion to milliwatts correctly, though the value carries the earlier factor-of-100 error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Faraday's law of induction to set up the peak generator voltage E0=NBAω\mathcal{E}_0 = N B A \omega.

You converted angular speed from revolutions per minute to radians per second without error.

You correctly applied the transformer turns ratio VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p} and calculated load power using P=VrmsIrmsP = V_{\text{rms}} I_{\text{rms}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Area unit conversion error

You used the linear scale factor 10−210^{-2} instead of squaring it to (10−2)2=10−4(10^{-2})^2 = 10^{-4} when converting from cm2\text{cm}^2 to m2\text{m}^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing linear metric prefix multipliers (1 cm=10−2 m1\text{ cm} = 10^{-2}\text{ m}) with derived area metric multipliers ((1 cm)2=10−4 m2(1\text{ cm})^2 = 10^{-4}\text{ m}^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Converting Derived Area Units
  • When converting an area unit with a metric prefix, you must square the linear prefix factor: 1 cm2=(10−2 m)2=10−4 m21\text{ cm}^2 = (10^{-2}\text{ m})^2 = 10^{-4}\text{ m}^2.

  • Always write (10−2 m)2(10^{-2}\text{ m})^2 explicitly so the exponent doubles before multiplying by the numeric value.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert area correctly: A=45.0 cm2×(10−2 m1 cm)2=4.50×10−3 m2A = 45.0\text{ cm}^2 \times \left(\frac{10^{-2}\text{ m}}{1\text{ cm}}\right)^2 = 4.50 \times 10^{-3}\text{ m}^2.

  2. Compute peak generator EMF: E0=500×0.0850 T×4.50×10−3 m2×188.5 rad/s≈36.05 V\mathcal{E}_0 = 500 \times 0.0850\text{ T} \times 4.50 \times 10^{-3}\text{ m}^2 \times 188.5\text{ rad/s} \approx 36.05\text{ V}.

  3. Find primary RMS voltage: Vp,rms=36.05 V2≈25.49 VV_{p,\text{rms}} = \frac{36.05\text{ V}}{\sqrt{2}} \approx 25.49\text{ V}.

  4. Find secondary RMS voltage: Vs,rms=40×25.49 V≈1019.7 VV_{s,\text{rms}} = 40 \times 25.49\text{ V} \approx 1019.7\text{ V}.

  5. Find RMS power delivered: Ps=1019.7 V×0.0175 A≈17.84 W=1.78×104 mWP_s = 1019.7\text{ V} \times 0.0175\text{ A} \approx 17.84\text{ W} = 1.78 \times 10^4\text{ mW}.

Final answer

(a) E0=36.0 V\mathcal{E}_0 = 36.0\text{ V}; (b) Ps=1.78×104 mWP_s = 1.78 \times 10^4\text{ mW} (17.8 W17.8\text{ W})

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out unit conversions with explicit parentheses when exponents are involved, such as (10−2 m)2(10^{-2}\text{ m})^2.

  • Check that dimensions match physical expectations; a miniature benchtop loop of 45 cm245\text{ cm}^2 is roughly the size of a credit card, while 0.45 m20.45\text{ m}^2 would be nearly half a square meter.

Lock it in

Similar question

01

A single-turn rectangular coil of area 0.020 m20.020\text{ m}^2 rotates at 3600 rpm3600\text{ rpm} in a uniform magnetic field of 0.50 T0.50\text{ T}. Calculate the peak open-circuit EMF E0\mathcal{E}_0 produced by this generator.

Answer

ω=3600×2π60=120π rad/s≈377.0 rad/s\omega = 3600 \times \frac{2\pi}{60} = 120\pi\text{ rad/s} \approx 377.0\text{ rad/s}. Using E0=NBAω=1×0.50×0.020×120π=1.2π V≈3.77 V\mathcal{E}_0 = N B A \omega = 1 \times 0.50 \times 0.020 \times 120\pi = 1.2\pi\text{ V} \approx 3.77\text{ V}.

02

An AC generator produces a peak output of E0=24.0 V\mathcal{E}_0 = 24.0\text{ V}. Its output is connected to a step-up transformer with primary turns Np=200N_p = 200 and secondary turns Ns=3000N_s = 3000. If the secondary is connected to a resistive load drawing an RMS current of 25.0 mA25.0\text{ mA}, find the RMS power delivered to the load.

Answer

Primary RMS voltage is Vp,rms=24.02≈16.97 VV_{p,\text{rms}} = \frac{24.0}{\sqrt{2}} \approx 16.97\text{ V}. Secondary RMS voltage is Vs,rms=(3000200)Vp,rms=15×16.97 V≈254.6 VV_{s,\text{rms}} = \left(\frac{3000}{200}\right) V_{p,\text{rms}} = 15 \times 16.97\text{ V} \approx 254.6\text{ V}. RMS power is P=Vs,rmsIs,rms=254.6 V×0.0250 A≈6.36 WP = V_{s,\text{rms}} I_{s,\text{rms}} = 254.6\text{ V} \times 0.0250\text{ A} \approx 6.36\text{ W} (6.36×103 mW6.36 \times 10^3\text{ mW}).

03

A wind turbine generator rotor with Ng=250 turnsN_g = 250\text{ turns} and loop area A=1.20 m2A = 1.20\text{ m}^2 rotates at 150 rpm150\text{ rpm} in Earth's local magnetic field component B=40.0 μTB = 40.0\ \mu\text{T}. The generator output feeds an ideal transformer (Np=50N_p = 50, Ns=2000N_s = 2000). Determine (a) the generator's peak output voltage E0\mathcal{E}_0 and (b) the secondary RMS voltage Vs,rmsV_{s,\text{rms}}.

Answer

First, ω=150×2π60=5π rad/s≈15.71 rad/s\omega = 150 \times \frac{2\pi}{60} = 5\pi\text{ rad/s} \approx 15.71\text{ rad/s}. (a) E0=NgBAω=250×(40.0×10−6 T)×1.20 m2×5π rad/s=0.060π V≈0.188 V\mathcal{E}_0 = N_g B A \omega = 250 \times (40.0 \times 10^{-6}\text{ T}) \times 1.20\text{ m}^2 \times 5\pi\text{ rad/s} = 0.060\pi\text{ V} \approx 0.188\text{ V}. (b) Vp,rms=E02≈0.1333 VV_{p,\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} \approx 0.1333\text{ V}. Vs,rms=(200050)Vp,rms=40×0.1333 V≈5.33 VV_{s,\text{rms}} = \left(\frac{2000}{50}\right) V_{p,\text{rms}} = 40 \times 0.1333\text{ V} \approx 5.33\text{ V}.

Loading workspace…