Resources
A stationary observer stands along a straight track while a train approaches at a constant speed of blowing an onboard whistle that emits a pure tone pitch of . After passing the observer, the train continues away at the same speed. Taking the speed of sound in still air to be , determine the observed frequency and pitch shift as the train approaches, and calculate the total perceived pitch drop heard by the observer as the source transitions from approaching to receding.
Answer and steps
Final answer
Observed approach frequency (pitch shift ), Total pitch drop
Steps
The Doppler Effect for Sound
When a sound source moves relative to a stationary observer, the observed frequency shifts due to the compression or stretching of the wavefronts in air:
where:
- is the rest frequency emitted by the source.
- is the speed of sound in air.
- is the speed of the moving source.
- The denominator uses the minus sign () when the source approaches the observer, and the plus sign () when it recedes.
Frequency and Pitch Shift During Approach
As the train moves toward the stationary observer, successive wavefronts are bunched together, reducing the effective wavelength and raising the observed frequency (perceived as a higher pitch):
Substitute the given values:
Simplifying the fraction :
The frequency shift (increase in pitch) relative to the emitted tone is:
Observed Frequency During Recession
After the train passes the observer, the source moves away. The wavefronts are stretched out over a greater distance, lowering the observed pitch:
Substitute the numerical values:
Simplifying the fraction :
Total Perceived Pitch Drop
The total shift in pitch experienced by the observer as the source transitions from approaching to receding is the difference between the two observed frequencies:
Common Pitfall: The pitch drop across the transition is not simply twice the initial approach shift (). Because the source is moving, the Doppler factor involves the denominator , which creates an asymmetric shift between approaching and receding.
Typical errors
01 The student inverts the Doppler sign convention by adding the source speed in the denominator for approach and subtracting it for recession.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
When a sound source approaches a stationary observer, successive wavefronts bunch together, shortening the observed wavelength and raising the observed frequency. Because the frequency must increase, the denominator must become smaller: use , not .
- Step 2Correct
You correctly subtracted the emitted frequency from your calculated approach frequency, but because your was too low from the inverted sign in Step 1, your shift became negative instead of positive.
- Step 3Correct
When the source recedes, wavefronts stretch out and the observed frequency drops. To make the observed frequency smaller than , the denominator must be larger than , requiring rather than .
- Step 4Correct
Your subtraction step correctly took the difference between the two frequencies, but the reversed values resulted in a negative drop of instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the relevant Doppler parameters (, , and ).
You executed the arithmetic and fraction evaluations cleanly without calculation errors.
You correctly defined the shift formulas as differences between the calculated observed frequencies.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual confusion about how source motion modifies the effective wavelength and observed frequency.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou associated 'approach' with addition () and 'recession' with subtraction (). For a moving source, the speed term is in the denominator, so addition actually reduces the frequency while subtraction increases it.
REASONING PATH
Your ACEpath teacher’s suggested approach- Physical Reality Check (Approach vs. Recession)
An approaching sound source must always sound higher in pitch (), and a receding source must always sound lower ().
Before calculating, decide whether must be greater than or less than , and choose the sign in the denominator accordingly.
- Denominator Rule for a Moving Source
For a moving source and stationary observer, .
To make , make the denominator smaller by using . To make , make the denominator larger by using .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the correct sign for an approaching source: .
Calculate the approach pitch shift: .
Apply the correct sign for a receding source: .
Calculate the total pitch drop: .
(pitch shift ),
02 The student misplaces the velocity ratio by applying the moving-observer Doppler formula with source speed in the numerator rather than the moving-source formula.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You placed the relative speed adjustment in the numerator, which corresponds to a moving observer. For a moving sound source approaching a stationary observer, the wave speed relative to air remains while the wavelength is compressed, placing the term in the denominator.
- Step 2Correct
You correctly subtracted the rest frequency from your observed approach frequency, but the value was affected by the incorrect approach frequency from Step 1.
- Step 3Correct
You again applied the moving-observer ratio. For a moving source receding from a stationary observer, the speed of the source belongs in the denominator as .
- Step 4Correct
You used the correct definition for the total pitch drop between approach and recession, but your result inherits the errors from Steps 1 and 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the approach frequency is higher than the emitted frequency.
You correctly defined both pitch shifts as differences between the corresponding frequencies.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the moving-source Doppler formula with the moving-observer Doppler formula, modifying the numerator rather than the denominator .
REASONING PATH
Your ACEpath teacher’s suggested approach- Moving Source vs. Moving Observer
For a moving source and stationary observer, . For a moving observer and stationary source, .
Always identify whether the motion alters the wavelength in the medium (source moves denominator changes) or the rate of encountering wavefronts (observer moves numerator changes).
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the moving-source approach formula: .
Find the approach pitch shift: .
Use the moving-source receding formula: .
Calculate the total perceived pitch drop: .
(or ), ,
03 The student subtracts the source speed directly from the emitted frequency rather than applying the wave speed ratio in the Doppler relation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You added the source speed () directly to the source frequency (). The Doppler frequency shift is caused by the spatial compression of wavefronts, which scales the frequency by the ratio of wave speeds: .
- Step 2Correct
You applied the correct definition , but the numerical value was affected by your calculation of in Step 1.
- Step 3Correct
You subtracted the velocity directly from the frequency again rather than applying the moving-source Doppler relation for recession, .
- Step 4Correct
You correctly subtracted the receding frequency from the approaching frequency, but the result was propagated from the incorrect frequency values calculated above.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the observed frequency must be higher than on approach and lower than on recession.
You accurately defined the frequency differences and .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual misunderstanding rather than a computational slip, as source speed was treated as an additive frequency adjustment.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the Doppler frequency shift as a direct additive shift proportional to the numerical speed of the source () rather than a multiplicative ratio of wave speeds (). Adding meters per second to hertz violates dimensional consistency.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Homogeneity Check
Quantities being added or subtracted must share the same physical units ( and cannot be combined additively).
Always verify units before adding quantities: frequency is in () while speed is in .
- Moving Source Doppler Factor
When a sound source moves at speed through a medium with sound speed , wavefronts bunch up or stretch, modifying the observed frequency by a factor of .
Use when the source approaches, and when the source recedes.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the Doppler formula for a source moving toward a stationary observer:
Find the pitch shift on approach:
Apply the Doppler formula for a source moving away from a stationary observer:
Calculate the total perceived pitch drop:
, ,
Lock it in
When a sound source approaches a stationary observer, should the observed frequency be higher or lower than the rest frequency ?
Higher (). Wavefronts compress in front of the moving source, reducing wavelength and raising observed frequency (higher pitch).
Similar question
An ambulance emits a siren at while traveling toward a stationary pedestrian at . If the speed of sound is , find the frequency heard by the pedestrian.
Answer
The source approaches, so use in the denominator: .
A racing car emits an engine note of . A trackside spectator hears a frequency of as the car speeds directly away. Taking the speed of sound as , determine the speed of the racing car.
Answer
The car recedes, so . Setting up: . Solving gives .
A train approaches a stationary observer at sounding a horn, then passes and recedes at the same speed. If the observer hears a total pitch drop of across the transition and the speed of sound is , what is the horn's emitted frequency ?
Answer
Express the frequencies: and . Their difference is . Setting equal to yields .