Resources

An industrial storage tank holds hydraulic fluid with a density of ρ=880 kg/m3\rho = 880\text{ kg/m}^3. A technician needs to calibrate a chemical feed system that meters fluid flow by volume rather than mass. If the system delivers a mass flow rate of m˙=4.62 kg/s\dot{m} = 4.62\text{ kg/s}, determine the corresponding volumetric flow rate in cubic centimeters per second (cm3/s\text{cm}^3\text{/s}). Express your answer to three significant figures.

Answer and steps

Final answer

5.25×103 cm3/s5.25 \times 10^3\text{ cm}^3\text{/s}

Steps

01

Relate mass flow rate, density, and volumetric flow rate

The relationship between mass flow rate (m˙\dot{m}), density (ρ\rho), and volumetric flow rate (V˙\dot{V}) is given by:

m˙=ρV˙\dot{m} = \rho \dot{V}

Solving for the volumetric flow rate V˙\dot{V}:

V˙=m˙ρ\dot{V} = \frac{\dot{m}}{\rho}

02

Calculate the volumetric flow rate in SI units (m3/s\text{m}^3/\text{s})

Substitute the given values into the equation:

V˙=4.62 kg/s880 kg/m3=0.00525 m3/s\dot{V} = \frac{4.62\text{ kg/s}}{880\text{ kg/m}^3} = 0.00525\text{ m}^3/\text{s}

In scientific notation, this is 5.25×10−3 m3/s5.25 \times 10^{-3}\text{ m}^3/\text{s}.

03

Convert the units from m3/s\text{m}^3/\text{s} to cm3/s\text{cm}^3/\text{s}

To convert cubic meters to cubic centimeters, cube the linear conversion factor between meters and centimeters:

1 m=100 cm=102 cm1\text{ m} = 100\text{ cm} = 10^2\text{ cm}

(1 m)3=(102 cm)3  ⟹  1 m3=106 cm3(1\text{ m})^3 = (10^2\text{ cm})^3 \implies 1\text{ m}^3 = 10^6\text{ cm}^3

Apply this conversion factor to find V˙\dot{V} in cm3/s\text{cm}^3/\text{s}:

V˙=0.00525m3s×106 cm31 m3=5250 cm3/s\dot{V} = 0.00525\frac{\text{m}^3}{\text{s}} \times \frac{10^6\text{ cm}^3}{1\text{ m}^3} = 5250\text{ cm}^3/\text{s}

Common Pitfall: When converting units of area or volume, remember to raise the entire conversion factor to the corresponding power (squared for area, cubed for volume). Using 1 m3=100 cm31\text{ m}^3 = 100\text{ cm}^3 instead of 106 cm310^6\text{ cm}^3 is a frequent mistake.

04

Express the result to three significant figures

Writing the value 5250 cm3/s5250\text{ cm}^3/\text{s} in standard scientific notation with three significant figures yields:

V˙=5.25×103 cm3/s\dot{V} = 5.25 \times 10^3\text{ cm}^3/\text{s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses an incorrect linear conversion factor of 100 instead of 10⁶ to convert cubic meters to cubic centimeters, resulting in 0.525 cm³/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q=m˙ρ  ⟹  Q=0.00525 m3/sQ = \frac{\dot{m}}{\rho} \implies Q = 0.00525\text{ m}^3/\text{s}

  2. Step 2

    1 m=100 cm1\text{ m} = 100\text{ cm}

  3. Step 3

    Q=0.00525×100=0.525 cm3/sQ = 0.00525 \times 100 = 0.525\text{ cm}^3/\text{s}

    Correct

    Q=0.00525 m3/s×106 cm31 m3=5.25×103 cm3/sQ = 0.00525\text{ m}^3/\text{s} \times \frac{10^6\text{ cm}^3}{1\text{ m}^3} = 5.25 \times 10^3\text{ cm}^3/\text{s}

    You multiplied by the linear factor 100100 rather than cubing the factor to account for three spatial dimensions: 1 m3=(100 cm)3=106 cm31\text{ m}^3 = (100\text{ cm})^3 = 10^6\text{ cm}^3.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct physical relationship between volumetric flow rate, mass flow rate, and density.

You accurately computed the volumetric flow rate in standard SI units as 0.00525 m3/s0.00525\text{ m}^3/\text{s}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear instead of cubic conversion factor

You applied the one-dimensional conversion factor 1 m=100 cm1\text{ m} = 100\text{ cm} directly to a three-dimensional volume unit.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated unit prefixes as simple multiplicative constants without raising the entire equality (1 m=102 cm)(1\text{ m} = 10^2\text{ cm}) to the third power when dealing with volume.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimension Matching
  • When converting derived units with an exponent nn (such as area n=2n=2 or volume n=3n=3), the linear conversion factor must also be raised to the power nn.

  • Always write (1 m)3=(100 cm)3=106 cm3(1\text{ m})^3 = (100\text{ cm})^3 = 10^6\text{ cm}^3 before performing the multiplication.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Cube the linear equivalence: (1 m)3=(102 cm)3=106 cm3(1\text{ m})^3 = (10^2\text{ cm})^3 = 10^6\text{ cm}^3.

  2. Multiply the volumetric flow rate by the cubic conversion factor: 0.00525 m3/s×106 cm3/m3=5250 cm3/s0.00525\text{ m}^3/\text{s} \times 10^6\text{ cm}^3/\text{m}^3 = 5250\text{ cm}^3/\text{s}.

  3. Express the result in scientific notation with three significant figures: 5.25×103 cm3/s5.25 \times 10^3\text{ cm}^3/\text{s}.

Final answer

5.25×103 cm3/s5.25 \times 10^3\text{ cm}^3/\text{s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting units of area and volume by writing the full parenthesized conversion factor with its exponent.

  • Check your final magnitude for physical plausibility: 1 m31\text{ m}^3 is very large compared to 1 cm31\text{ cm}^3, so converting to cubic centimeters should result in a much larger number.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the relationship between mass flow rate, density, and volume, multiplying mass flow rate by density instead of dividing, leading to an incorrect flow rate of 4.07 × 10⁹ cm³/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q=m˙×ρ  ⟹  Q=4.62×880=4065.6 m3/sQ = \dot{m} \times \rho \implies Q = 4.62 \times 880 = 4065.6\text{ m}^3\text{/s}

    Correct

    V˙=m˙ρ=4.62 kg/s880 kg/m3=5.25×10−3 m3/s\dot{V} = \frac{\dot{m}}{\rho} = \frac{4.62\text{ kg/s}}{880\text{ kg/m}^3} = 5.25 \times 10^{-3}\text{ m}^3\text{/s}

    You defined the volumetric flow rate as the product of mass flow rate and density. Because density is mass per unit volume (ρ=m/V\rho = m/V), volumetric flow rate is obtained by dividing mass flow rate by density: V˙=m˙/ρ\dot{V} = \dot{m}/\rho.

  2. Step 2

    Q=4065.6×106=4.07×109 cm3/sQ = 4065.6 \times 10^6 = 4.07 \times 10^9\text{ cm}^3\text{/s}

    Correct

    V˙=5.25×10−3 m3/s×106 cm3/m3=5.25×103 cm3/s\dot{V} = 5.25 \times 10^{-3}\text{ m}^3\text{/s} \times 10^6\text{ cm}^3\text{/m}^3 = 5.25 \times 10^3\text{ cm}^3\text{/s}

    Your conversion method multiplying by 106 cm3/m310^6\text{ cm}^3\text{/m}^3 and rounding to three significant figures was executed correctly, but the numerical value was carried forward from the initial formula error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the conversion factor (100 cm/m)3=106 cm3/m3(100\text{ cm/m})^3 = 10^6\text{ cm}^3\text{/m}^3 to convert cubic meters to cubic centimeters.

You correctly rounded your final value to three significant figures in standard scientific notation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted flow rate formula

You multiplied mass flow rate by density instead of dividing by density.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misremembering the algebraic relationship between mass, volume, and density. Since density represents mass per unit volume (ρ=m/V\rho = m/V), volume is mass divided by density (V=m/ρV = m/\rho), meaning V˙=m˙/ρ\dot{V} = \dot{m}/\rho.

REASONING PATH
Your ACEpath teacher’s suggested approach
Perform dimensional analysis on your formula
  • The units on both sides of a physical equation must match.

  • Check the units: multiplying gives (kg/s)×(kg/m3)=kg2/(m3⋅s)(\text{kg/s}) \times (\text{kg/m}^3) = \text{kg}^2/(\text{m}^3\cdot\text{s}), which is not volume per unit time. Dividing gives (kg/s)/(kg/m3)=m3/s(\text{kg/s}) / (\text{kg/m}^3) = \text{m}^3\text{/s}.

Rearrange from the primary definition
  • Start from the standard definition m˙=ρV˙\dot{m} = \rho \dot{V}.

  • Isolate volumetric flow rate by dividing both sides by density: V˙=m˙/ρ\dot{V} = \dot{m}/\rho.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the relationship between mass flow rate and volumetric flow rate: V˙=m˙ρ\dot{V} = \frac{\dot{m}}{\rho}.

  2. Substitute the given numerical values: V˙=4.62 kg/s880 kg/m3=0.00525 m3/s=5.25×10−3 m3/s\dot{V} = \frac{4.62\text{ kg/s}}{880\text{ kg/m}^3} = 0.00525\text{ m}^3\text{/s} = 5.25 \times 10^{-3}\text{ m}^3\text{/s}.

  3. Convert from m3/s\text{m}^3\text{/s} to cm3/s\text{cm}^3\text{/s}: V˙=5.25×10−3 m3/s×106 cm3/m3=5250 cm3/s\dot{V} = 5.25 \times 10^{-3}\text{ m}^3\text{/s} \times 10^6\text{ cm}^3\text{/m}^3 = 5250\text{ cm}^3\text{/s}.

Final answer

5.25×103 cm3/s5.25 \times 10^3\text{ cm}^3\text{/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out the units alongside numbers in calculations to verify that units cancel out to the desired target quantity.

  • Practice rearranging the density formula ρ=m/V\rho = m/V for each variable (m=ρVm = \rho V and V=m/ρV = m/\rho) before substituting numerical values.

OverviewACEpath Teacher's Diagnosis

03 The student squares the linear conversion factor (using 10⁴ instead of 10⁶) when converting cubic meters to cubic centimeters, resulting in 52.5 cm³/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q=m˙ρ  ⟹  Q=4.62880=0.00525 m3/sQ = \frac{\dot{m}}{\rho} \implies Q = \frac{4.62}{880} = 0.00525\text{ m}^3/\text{s}

  2. Step 2

    1 m3=1002 cm3=10000 cm31\text{ m}^3 = 100^2\text{ cm}^3 = 10000\text{ cm}^3

    Correct

    1 m3=(100 cm)3=106 cm3=1 000 000 cm31\text{ m}^3 = (100\text{ cm})^3 = 10^6\text{ cm}^3 = 1\,000\,000\text{ cm}^3

    Because volume is three-dimensional, you must cube the linear factor (100 cm)3=106 cm3(100\text{ cm})^3 = 10^6\text{ cm}^3, rather than squaring it.

  3. Step 3

    Q=0.00525×10000=52.5 cm3/sQ = 0.00525 \times 10000 = 52.5\text{ cm}^3/\text{s}

    Correct

    Q=0.00525×106=5.25×103 cm3/sQ = 0.00525 \times 10^6 = 5.25 \times 10^3\text{ cm}^3/\text{s}

    Your final multiplication carried forward the incorrect conversion factor from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the physical formula relating mass flow rate, density, and volume flow rate.

You accurately calculated the numerical value in SI units as 0.00525 m3/s0.00525\text{ m}^3/\text{s}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimensional conversion power error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied an area conversion exponent (1002100^2) instead of a volume conversion exponent (1003100^3) when deriving the relationship between cubic meters and cubic centimeters.

REASONING PATH
Your ACEpath teacher’s suggested approach
Volume Unit Derivation
  • When converting derived units of volume, raise the entire linear conversion equality (1 m=100 cm)(1\text{ m} = 100\text{ cm}) to the third power: (1 m)3=(102 cm)3=106 cm3(1\text{ m})^3 = (10^2\text{ cm})^3 = 10^6\text{ cm}^3.

  • Always write out parentheses around both the coefficient and unit before expanding the power: (100 cm)3(100\text{ cm})^3.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. 1 m3=(100 cm)3=106 cm31\text{ m}^3 = (100\text{ cm})^3 = 10^6\text{ cm}^3

  2. Q=0.00525 m3/s×106 cm3/m3=5250 cm3/s=5.25×103 cm3/sQ = 0.00525\text{ m}^3/\text{s} \times 10^6\text{ cm}^3/\text{m}^3 = 5250\text{ cm}^3/\text{s} = 5.25 \times 10^3\text{ cm}^3/\text{s}

Final answer

5.25×103 cm3/s5.25 \times 10^3\text{ cm}^3/\text{s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review three-dimensional dimensional analysis by practicing exponent distribution across conversion factors.

  • Always check that the power on your linear scaling factor matches the physical dimension (1 for length, 2 for area, 3 for volume).

Lock it in

Similar question

01

A pipeline transports oil at a volumetric flow rate of 0.018 m3/s0.018\text{ m}^3/\text{s}. Convert this flow rate to cubic centimeters per second (cm3/s\text{cm}^3/\text{s}) in scientific notation.

Answer

1.8×104 cm3/s1.8 \times 10^4\text{ cm}^3/\text{s}. Step: Multiply by the volume conversion factor: 0.018 m3/s×106 cm3/m3=18000 cm3/s=1.8×104 cm3/s0.018\text{ m}^3/\text{s} \times 10^6\text{ cm}^3/\text{m}^3 = 18000\text{ cm}^3/\text{s} = 1.8 \times 10^4\text{ cm}^3/\text{s}.

02

A pump moves water with density ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg/m}^3 at a mass flow rate of m˙=0.750 kg/s\dot{m} = 0.750\text{ kg/s}. Calculate the volumetric flow rate in cm3/s\text{cm}^3/\text{s}.

Answer

750 cm3/s750\text{ cm}^3/\text{s}. Steps: First find volume rate in SI: V˙=m˙ρ=0.7501000=7.50×10−4 m3/s\dot{V} = \frac{\dot{m}}{\rho} = \frac{0.750}{1000} = 7.50 \times 10^{-4}\text{ m}^3/\text{s}. Then convert to cm3/s\text{cm}^3/\text{s}: 7.50×10−4×106=750 cm3/s7.50 \times 10^{-4} \times 10^6 = 750\text{ cm}^3/\text{s}.

03

A cylindrical syringe with cross-sectional area A=3.50 cm2A = 3.50\text{ cm}^2 dispenses saline solution at a steady linear piston speed of v=4.00 cm/sv = 4.00\text{ cm/s}. Determine the mass flow rate in kg/s\text{kg/s} if the solution density is ρ=1020 kg/m3\rho = 1020\text{ kg/m}^3.

Answer

0.0143 kg/s0.0143\text{ kg/s} (or 1.43×10−2 kg/s1.43 \times 10^{-2}\text{ kg/s}). Steps: Volumetric flow rate is V˙=A⋅v=3.50 cm2×4.00 cm/s=14.0 cm3/s\dot{V} = A \cdot v = 3.50\text{ cm}^2 \times 4.00\text{ cm/s} = 14.0\text{ cm}^3/\text{s}. Convert to m3/s\text{m}^3/\text{s}: 14.0×10−6 m3/s14.0 \times 10^{-6}\text{ m}^3/\text{s}. Then calculate mass flow rate: m˙=ρV˙=1020 kg/m3×1.40×10−5 m3/s=0.01428 kg/s≈1.43×10−2 kg/s\dot{m} = \rho \dot{V} = 1020\text{ kg/m}^3 \times 1.40 \times 10^{-5}\text{ m}^3/\text{s} = 0.01428\text{ kg/s} \approx 1.43 \times 10^{-2}\text{ kg/s}.

Loading workspace…