Resources
An electric heating element connected to a constant DC terminal voltage of draws a steady current of . The technician must reduce the thermal output by modifying the component to an operating resistance that will draw exactly under the same applied potential difference. Calculate the required change in resistance, , in ohms ().
Answer and steps
Final answer
Steps
Calculate the initial resistance ()
To find the required change in resistance, we use Ohm's Law, which relates voltage (), current (), and resistance ():
The heating element initially draws a current of from a source of :
Calculate the target resistance ()
To reduce the current to under the same constant potential difference of , the resistance must increase:
Determine the change in resistance ()
The required increase in resistance is:
Common Pitfall: Remember that current is inversely proportional to resistance when voltage is held constant (). A lower current requires a higher resistance, so must be positive.
Typical errors
01 The student subtracts the new resistance from the initial resistance instead of calculating R_new - R_initial, resulting in a negative change in resistance.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
By definition, change is always final minus initial (). Because the current decreased at constant voltage, the circuit resistance had to increase, meaning must be positive.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used Ohm's law () to find the initial resistance of .
You correctly applied Ohm's law to determine the new resistance of .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of , producing a negative sign.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating the standard physical definition of change () with 'initial minus final', or not performing a physical sanity check that lower current at constant voltage requires an increase in resistance.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Change ($\Delta$)
In physics, any change represented by is strictly defined as .
Always write out before plugging in numerical values.
- Qualitative Sense Check
At constant voltage, current is inversely proportional to resistance ().
Check that if current drops, resistance must increase, meaning .
CORRECTED PATH
ACEpath Teacher's DemonstrationState the definition of change:
Substitute the computed resistances:
02 The student misinverts Ohm's law as R = I / V, leading to incorrect values for both resistances.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You inverted the Ohm's law relationship by computing instead of . Ohm's law states , so resistance is .
- Step 2Correct
You used the inverted ratio again here. Dividing voltage by the new current gives .
- Step 3Correct
You correctly stated the definition of and subtracted your two values, but the result was negative because both calculated resistances were inverted.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the required change in resistance is given by .
You carried out your arithmetic consistently based on your chosen formulas.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided current by voltage () rather than voltage by current ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused electrical resistance () with electrical conductance (). Remember that to limit or reduce current when voltage stays constant, resistance must increase, meaning must be directly proportional to and inversely proportional to .
REASONING PATH
Your ACEpath teacher’s suggested approach- Recall the fundamental form of Ohm's Law
Isolate by dividing both sides by current: .
- Sanity check physical behavior
At fixed voltage, , so current is inversely proportional to resistance.
Since current decreased from to , verify that and .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute initial resistance: .
Compute target resistance: .
Subtract initial resistance from target resistance: .
03 The student incorrectly calculates the change in current and then applies Ohm's law directly as V / ΔI, falsely assuming resistance differences are inversely proportional to current differences.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Ohm's law relates total quantities (), not differences. Since is an inverse function rather than a linear function, . To find , you must evaluate each state's resistance separately and subtract them.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the net change in current between the initial and target operating states.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that Ohm's law can be applied directly to finite differences as . Because varies inversely with , differences of fractions do not equal the fraction of differences: .
REASONING PATH
Your ACEpath teacher’s suggested approach- Evaluate individual state resistances first
For a constant voltage , calculate and independently before subtracting.
Avoid writing . Always compute each state's resistance individually when voltage is held fixed.
- Perform a physical direction check
When current decreases under a constant potential difference, resistance must increase.
Check the sign of your answer: a reduction in current from to must require a positive change in resistance ().
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the initial resistance: .
Find the target resistance: .
Compute the required difference: .
Lock it in
What is the standard mathematical and physical definition of change for any quantity , denoted by ?
. A positive indicates an increase, while a negative indicates a decrease.
Similar question
A power supply is connected across a variable resistor. Initially, the resistor draws a current of . The resistance is then adjusted so that the current drops to under the same voltage. Calculate the change in resistance, , in ohms.
Answer
. First find . Then find . Finally, calculate .
A heating coil operates at and initially draws . To boost thermal output, a technician reduces the resistance so that it draws . Determine the change in resistance, .
Answer
. , and . Thus (negative because resistance decreased).
A filament lamp has a cold resistance of . When connected to a line, it reaches operating temperature and draws a steady current of . Find the change in resistance from the cold state to the operating state, and verify its sign physically.
Answer
. The hot operating resistance is . The change is . The positive sign makes physical sense because the metal filament's resistance increases as it heats up.