Resources
A residential electric storage water heater consumed a total of of electrical energy during a heating cycle lasting across a nominal line voltage of . Assuming the heating element acts as an ideal ohmic resistor, determine: (a) the average electric power dissipated by the element in kilowatts, and (b) the initial electrical resistance of the submerged heating element.
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Calculating the Average Electric Power ()
Electric power measures the rate at which electrical energy is transferred or consumed over time:
- Convert the heating time to hours so the unit matches :
- Compute the power:
Part (b): Calculating the Electrical Resistance ()
For an ideal ohmic resistor operating across an electric potential difference , power is related to voltage and resistance by:
Rearranging to solve for resistance :
-
Convert power to standard SI units (watts):
Common Pitfall: Always convert power from kilowatts () to watts () before calculating resistance with voltage in volts (). Using instead of would result in an incorrect resistance off by a factor of .
- Substitute the nominal voltage and power:
Typical errors
01 The student divides energy by time in minutes without converting minutes to hours, yielding an incorrect power of 0.060 kW.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly recalled the definition of average power . However, because the energy was given in kilowatt-hours (), the time interval must be in hours before dividing. Dividing by yields rather than kilowatts.
- Step 2Correct
Your conversion from kilowatts to watts () was carried out correctly, but the numerical value was carried over from your incorrect result in part (a).
- Step 3Correct
You selected the correct formula relating voltage, power, and resistance () and performed the arithmetic without error. Your final answer is off because it used the affected power value of instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the fundamental formula to calculate average power.
You recognized that power in kilowatts must be converted to watts before calculating resistance using volts in SI units.
You accurately rearranged and applied the ohmic power relationship .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the duration directly into the denominator without converting minutes to hours to cancel the hours in .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating composite non-standard units (such as ) as purely numerical values during substitution, rather than explicitly tracking and matching unit dimensions across numerator and denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match composite energy units to time units
Because , dividing by time requires to be expressed in hours so that the time units cancel: .
Always write out units during substitution: .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the heating cycle time into hours: .
Recalculate power in kilowatts: .
Convert power to SI units for resistance calculation: .
Re-evaluate the element's resistance: .
(a) ; (b)
02 The student uses the power in kilowatts directly in the formula R = V² / P instead of converting to watts, resulting in an incorrect resistance of 16000 Ω.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You substituted the power as instead of converting it to standard SI units (). Because the ohm is defined as , power must be in watts.
- Step 5Correct
Your arithmetic evaluation was correct for the substituted numbers, but the result is off by a factor of due to the unit error in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou converted time into hours to determine the average power in kilowatts accurately.
You recognized the correct relationship between resistance, potential difference, and power as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou plugged in the power value in kilowatts directly alongside voltage in volts without converting kilowatts to watts.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the SI base unit coherence required by Ohm's law and Joule's law formulas: , which requires power to be in watts (W) rather than kilowatts (kW).
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify SI Unit Coherence
Electrical formulas involving volts (), amperes (), and ohms () require power in watts (), where .
Always convert power values with metric prefixes (like or ) into base watts before using formulas like .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the power from kilowatts to watts: .
Substitute and into the resistance formula: .
Divide to find the resistance: .
(a) ; (b)
03 The student forgets to square the voltage in the power-resistance relation, mistakenly using R = V / P instead of R = V² / P.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You forgot to square the voltage when relating power to resistance. Because , solving for resistance gives .
- Step 5Correct
Your numerical substitution and rounding followed your stated formula, but the final resistance was affected by the missing squared term.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the heating time from minutes to hours to match the energy unit.
You accurately found the average power in kilowatts using .
You correctly converted power into watts () for SI consistency.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote rather than , likely confounding Ohm's law () with the electric power relation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the linear relationship between voltage and current in Ohm's law () with the quadratic relationship between voltage and electrical power ( or ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Power-Voltage-Resistance Formula
For an ohmic resistor, .
Derive the formula by combining and to verify that voltage is squared: .
- Unit and Dimensional Check
Resistance has units of ohms (), whereas .
Check the dimensions of your expression before plugging in numbers: .
CORRECTED PATH
ACEpath Teacher's DemonstrationStart from the ohmic power relation: .
Rearrange for resistance: .
Substitute and : .
Lock it in
What unit of time must be used in the denominator of if energy is given in kilowatt-hours ()?
Hours (). Since , dividing by hours cancels the time unit and yields power directly in kilowatts ().
Similar question
An electric oven consumes over a baking period of . Determine the average power rating of the oven in kilowatts.
Answer
. Key steps: Convert time to hours: . Calculate power: .
A space heater rated at consumes during a run time of . Assuming it behaves as an ideal resistor, calculate: (a) its power consumption in kilowatts, and (b) its internal electrical resistance in ohms.
Answer
(a) ; (b) . Key steps: (a) . Power . (b) Convert power to watts: . Use .
An industrial immersion heater has an ohmic resistance of and operates connected to a line. How much energy in does it consume if it runs continuously for ?
Answer
. Key steps: Compute power dissipation in watts: . Convert time to hours: . Compute energy: .