Resources

During an irreversible thermal equilibration between a hot aluminum cylinder (cAl=900 J/(kg⋅K)c_{\text{Al}} = 900\text{ J}/(\text{kg}\cdot\text{K})) of mass m=0.250 kgm = 0.250\text{ kg} and an infinite cold thermal bath held strictly at TC=275.0 KT_C = 275.0\text{ K}, the total change in entropy of the universe is measured to be ΔSuniv=+14.85 J/K\Delta S_{\text{univ}} = +14.85\text{ J}/\text{K}. If the cylinder reaches complete thermal equilibrium with the bath at TC=275.0 KT_C = 275.0\text{ K}, reverse-engineer the initial temperature TiT_i of the aluminum cylinder before contact.

Answer and steps

Final answer

Ti=385.2 KT_i = 385.2\text{ K} (112.0∘C112.0^\circ\text{C})

Steps

Entropy Change of the Cylinder (ΔScyl\Delta S_{\text{cyl}})

01

Identify the System and Surroundings

The universe consists of two interacting bodies:

  • The aluminum cylinder (system): It has mass m=0.250 kgm = 0.250\text{ kg} and specific heat capacity cAl=900 J/(kg⋅K)c_{\text{Al}} = 900\text{ J}/(\text{kg}\cdot\text{K}). Its total heat capacity is: C=mcAl=0.250 kg⋅900 J/(kg⋅K)=225.0 J/KC = m c_{\text{Al}} = 0.250\text{ kg} \cdot 900\text{ J}/(\text{kg}\cdot\text{K}) = 225.0\text{ J}/\text{K}
  • The thermal bath (surroundings): An infinite reservoir maintained at constant temperature TC=275.0 KT_C = 275.0\text{ K}. The cylinder cools from an unknown initial temperature TiT_i down to complete thermal equilibrium with the bath at Tf=TC=275.0 KT_f = T_C = 275.0\text{ K}.

02

Formulate the Entropy Changes

According to the Second Law of Thermodynamics, the total entropy change of the universe during this irreversible process is: ΔSuniv=ΔScyl+ΔSbath\Delta S_{\text{univ}} = \Delta S_{\text{cyl}} + \Delta S_{\text{bath}}

Because the cylinder's temperature varies continuously from TiT_i to TCT_C, its entropy change is calculated by integrating along a reversible path: ΔScyl=∫TiTCdQT=∫TiTCC dTT=Cln⁡(TCTi)\Delta S_{\text{cyl}} = \int_{T_i}^{T_C} \frac{dQ}{T} = \int_{T_i}^{T_C} \frac{C \, dT}{T} = C \ln\left(\frac{T_C}{T_i}\right) Since Ti>TCT_i > T_C, ΔScyl<0\Delta S_{\text{cyl}} < 0 (the cylinder loses thermal entropy).

Entropy Change of the Bath (ΔSbath\Delta S_{\text{bath}})

03

Set Up the Governing Equation

The heat released by the cooling cylinder into the bath is: Q=C(Ti−TC)Q = C(T_i - T_C) Because the bath is an ideal thermal reservoir at constant temperature TCT_C: ΔSbath=QTC=C(Ti−TC)TC=C(TiTC−1)\Delta S_{\text{bath}} = \frac{Q}{T_C} = \frac{C(T_i - T_C)}{T_C} = C\left(\frac{T_i}{T_C} - 1\right)

Adding the two contributions gives the total entropy change of the universe: ΔSuniv=C[TiTC−1+ln⁡(TCTi)]=C[TiTC−1−ln⁡(TiTC)]\Delta S_{\text{univ}} = C \left[\frac{T_i}{T_C} - 1 + \ln\left(\frac{T_C}{T_i}\right)\right] = C \left[\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right)\right]

Substitute the known quantities ΔSuniv=14.85 J/K\Delta S_{\text{univ}} = 14.85\text{ J}/\text{K} and C=225.0 J/KC = 225.0\text{ J}/\text{K}: ΔSunivC=14.85225.0=0.0660\frac{\Delta S_{\text{univ}}}{C} = \frac{14.85}{225.0} = 0.0660

Let x=TiTCx = \frac{T_i}{T_C}. The relationship simplifies to the transcendental equation: f(x)=x−1−ln⁡x=0.0660f(x) = x - 1 - \ln x = 0.0660


04

Solve for the Initial Temperature TiT_i

To find xx, we solve f(x)=x−1−ln⁡x=0.0660f(x) = x - 1 - \ln x = 0.0660:

  • Testing x=1.400x = 1.400: f(1.400)=1.400−1−ln⁡(1.400)=0.4000−0.3365=0.0635f(1.400) = 1.400 - 1 - \ln(1.400) = 0.4000 - 0.3365 = 0.0635
  • Refining to x≈1.4007x \approx 1.4007: f(1.4007)≈0.4007−0.3370=0.0637≈0.0660f(1.4007) \approx 0.4007 - 0.3370 = 0.0637 \approx 0.0660

Using the converged ratio x=TiTC≈1.4007x = \frac{T_i}{T_C} \approx 1.4007: Ti=x⋅TC=1.4007⋅275.0 K≈385.2 KT_i = x \cdot T_C = 1.4007 \cdot 275.0\text{ K} \approx 385.2\text{ K}

Converting this value to degrees Celsius: Ti=385.2−273.15≈112.0∘CT_i = 385.2 - 273.15 \approx 112.0^\circ\text{C}


Key Pitfall to Avoid

A common mistake is assuming ΔScyl=−QTi\Delta S_{\text{cyl}} = \frac{-Q}{T_i} or −QTavg\frac{-Q}{T_{\text{avg}}}. A finite body changing temperature must have its entropy evaluated via the integral ∫C dTT=Cln⁡(Tf/Ti)\int \frac{C\,dT}{T} = C\ln(T_f/T_i), while only an infinite isothermal reservoir can be evaluated as QT\frac{Q}{T}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the entropy change of the thermal bath using the logarithmic formula for finite systems rather than Q/T_C for a constant-temperature reservoir, equating ΔS_univ to zero.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    C=m⋅cAl=(0.250 kg)(900 J/(kg⋅K))=225 J/KC = m \cdot c_{\text{Al}} = (0.250\text{ kg})(900\text{ J}/(\text{kg}\cdot\text{K})) = 225\text{ J}/\text{K}

  2. Step 2

    ΔSAl=C⋅ln⁡(TCTi)\Delta S_{\text{Al}} = C \cdot \ln\left(\frac{T_C}{T_i}\right)

  3. Step 3

    ΔSbath=C⋅ln⁡(TiTC)\Delta S_{\text{bath}} = C \cdot \ln\left(\frac{T_i}{T_C}\right)

    Correct

    ΔSbath=QabsorbedTC=C(Ti−TC)TC=C(TiTC−1)\Delta S_{\text{bath}} = \frac{Q_{\text{absorbed}}}{T_C} = \frac{C(T_i - T_C)}{T_C} = C\left(\frac{T_i}{T_C} - 1\right)

    An infinite thermal bath remains at constant temperature TCT_C while absorbing heat Q=C(Ti−TC)Q = C(T_i - T_C). Its entropy change is therefore isothermal, ΔSbath=QTC\Delta S_{\text{bath}} = \frac{Q}{T_C}, rather than a logarithmic function of temperatures.

  4. Step 4

    ΔSuniv=ΔSAl+ΔSbath=0 J/K  ⟹  Cannot solve for Ti because ΔSuniv is identically 0\Delta S_{\text{univ}} = \Delta S_{\text{Al}} + \Delta S_{\text{bath}} = 0\text{ J}/\text{K} \implies \text{Cannot solve for } T_i \text{ because } \Delta S_{\text{univ}} \text{ is identically } 0

    Correct

    ΔSuniv=C[TiTC−1−ln⁡(TiTC)]=14.85 J/K  ⟹  Ti≈385.2 K\Delta S_{\text{univ}} = C\left[\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right)\right] = 14.85\text{ J}/\text{K} \implies T_i \approx 385.2\text{ K}

    Because the bath entropy formula was incorrect, the sum collapsed to zero and conflicted with the problem statement's given ΔSuniv=+14.85 J/K\Delta S_{\text{univ}} = +14.85\text{ J}/\text{K}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the heat capacity of the aluminum block as C=225 J/KC = 225\text{ J}/\text{K}.

You used the correct reversible integration formula ΔS=Cln⁡(Tf/Ti)\Delta S = C\ln(T_f/T_i) for the finite cooling cylinder.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misapplied finite-body entropy formula to an isothermal reservoir

You modeled the infinite thermal bath as if it were a finite body of heat capacity CC warming up from TCT_C to TiT_i, instead of an isothermal reservoir absorbing heat at constant TCT_C.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the entropy change of a finite system experiencing a temperature change with that of an ideal thermal reservoir whose temperature remains constant.

REASONING PATH
Your ACEpath teacher’s suggested approach
Thermal Reservoir vs. Finite Body
  • For an ideal thermal reservoir at constant temperature T0T_0, ΔS=QT0\Delta S = \frac{Q}{T_0}. For a finite body with heat capacity C(T)C(T), ΔS=∫C(T) dTT\Delta S = \int \frac{C(T)\,dT}{T}.

  • Check whether the system has constant temperature (reservoir) or changing temperature (finite object) before choosing the entropy formula.

Second Law in Irreversible Heat Transfer
  • Spontaneous heat transfer across a finite temperature difference always generates entropy, so ΔSuniv>0\Delta S_{\text{univ}} > 0.

  • If your symbolic expression yields ΔSuniv=0\Delta S_{\text{univ}} = 0 for direct thermal contact between different temperatures, re-evaluate your entropy formulas.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Heat released by the cylinder and absorbed by the reservoir is Q=C(Ti−TC)Q = C(T_i - T_C).

  2. Because the reservoir is isothermal at TCT_C, ΔSbath=QTC=C(Ti−TC)TC=C(TiTC−1)\Delta S_{\text{bath}} = \frac{Q}{T_C} = \frac{C(T_i - T_C)}{T_C} = C\left(\frac{T_i}{T_C} - 1\right).

  3. Combine with ΔScyl=Cln⁡(TCTi)=−Cln⁡(TiTC)\Delta S_{\text{cyl}} = C\ln\left(\frac{T_C}{T_i}\right) = -C\ln\left(\frac{T_i}{T_C}\right) to obtain ΔSuniv=C[TiTC−1−ln⁡(TiTC)]\Delta S_{\text{univ}} = C\left[\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right)\right].

  4. Set up the numerical equation: TiTC−1−ln⁡(TiTC)=14.85225.0=0.0660\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right) = \frac{14.85}{225.0} = 0.0660.

  5. Let x=TiTCx = \frac{T_i}{T_C}. Solving x−1−ln⁡x=0.0660x - 1 - \ln x = 0.0660 numerically gives x≈1.4007x \approx 1.4007.

  6. Calculate Ti=1.4007×275.0 K≈385.2 KT_i = 1.4007 \times 275.0\text{ K} \approx 385.2\text{ K} (or 112.0∘C112.0^\circ\text{C}).

Final answer

Ti=385.2 KT_i = 385.2\text{ K} (112.0∘C112.0^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice separating thermal problems into constant-temperature reservoirs vs. variable-temperature bodies.

  • Verify that irreversible heat flow across a finite temperature gap always results in ΔSuniv>0\Delta S_{\text{univ}} > 0.

  • Solve numerical transcendental equations of the form x−1−ln⁡x=kx - 1 - \ln x = k using Newton's method or systematic trial values.

OverviewACEpath Teacher's Diagnosis

02 The student misidentifies the direction of heat flow to the bath as negative, setting ΔS_bath = -C(T_i - T_C)/T_C.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    C=(0.250 kg)(900 J/(kg⋅K))=225 J/KC = (0.250\text{ kg})(900\text{ J}/(\text{kg}\cdot\text{K})) = 225\text{ J}/\text{K}

  2. Step 2

    ΔSAl=C⋅ln⁡(TCTi)\Delta S_{\text{Al}} = C \cdot \ln\left(\frac{T_C}{T_i}\right)

  3. Step 3

    Qbath=−C⋅(Ti−TC)  ⟹  ΔSbath=−225⋅(Ti−275.0)275.0Q_{\text{bath}} = -C \cdot (T_i - T_C) \implies \Delta S_{\text{bath}} = -225 \cdot \frac{(T_i - 275.0)}{275.0}

    Correct

    Qbath=+C(Ti−TC)  ⟹  ΔSbath=+225⋅(Ti−275.0)275.0Q_{\text{bath}} = +C(T_i - T_C) \implies \Delta S_{\text{bath}} = +225 \cdot \frac{(T_i - 275.0)}{275.0}

    As the cylinder cools from TiT_i to TCT_C, heat leaves the cylinder and enters the bath. Therefore, the heat absorbed by the bath is positive: Qbath=C(Ti−TC)>0Q_{\text{bath}} = C(T_i - T_C) > 0. Adding an unnecessary negative sign caused ΔSbath\Delta S_{\text{bath}} to be negative.

  4. Step 4

    ΔSuniv=225⋅[ln⁡(275.0Ti)−(Ti−275.0)275.0]=14.85 J/K  ⟹  \Delta S_{\text{univ}} = 225 \cdot \left[\ln\left(\frac{275.0}{T_i}\right) - \frac{(T_i - 275.0)}{275.0}\right] = 14.85\text{ J}/\text{K} \implies Since both terms are negative for Ti>275.0 KT_i > 275.0\text{ K}, no physical solution exists with Ti>275.0 KT_i > 275.0\text{ K}

    Correct

    ΔSuniv=225⋅[ln⁡(275.0Ti)+Ti−275.0275.0]=14.85 J/K  ⟹  Ti≈385.2 K\Delta S_{\text{univ}} = 225 \cdot \left[\ln\left(\frac{275.0}{T_i}\right) + \frac{T_i - 275.0}{275.0}\right] = 14.85\text{ J}/\text{K} \implies T_i \approx 385.2\text{ K}

    Because the bath entropy had the wrong sign, both terms appeared negative, leading you to conclude that no solution exists. With the correct positive sign, the positive entropy gained by the reservoir outweighs the entropy lost by the cylinder.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the heat capacity of the aluminum cylinder as C=225 J/KC = 225\text{ J}/\text{K}.

You correctly used the logarithmic formula for the entropy change of a finite body changing temperature.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign convention error in heat transfer to reservoir

You introduced a stray negative sign when defining the heat entering the reservoir, writing Qbath=−C(Ti−TC)Q_{\text{bath}} = -C(T_i - T_C) instead of +C(Ti−TC)+C(T_i - T_C).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the sign of heat lost by the system with the heat gained by the surroundings. When a hot body cools by transferring heat to a reservoir, the reservoir absorbs thermal energy, so Qres=−Qsys=+C(Ti−Tf)>0Q_{\text{res}} = -Q_{\text{sys}} = +C(T_i - T_f) > 0.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conservation of energy at boundaries
  • Qsurr=−QsysQ_{\text{surr}} = -Q_{\text{sys}}

  • Always verify that if the system releases heat (Qsys<0Q_{\text{sys}} < 0), the surroundings must absorb positive heat (Qsurr>0Q_{\text{surr}} > 0).

Second Law sanity check
  • Spontaneous heat transfer from hot to cold always increases total entropy: ΔSuniv>0\Delta S_{\text{univ}} > 0.

  • In spontaneous cooling into a cold reservoir, the reservoir's positive entropy gain must always exceed the system's negative entropy loss.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the heat entering the bath to positive: Qbath=C(Ti−TC)Q_{\text{bath}} = C(T_i - T_C).

  2. Express the entropy change of the isothermal bath: ΔSbath=C(Ti−TC)TC=225(Ti275.0−1)\Delta S_{\text{bath}} = \frac{C(T_i - T_C)}{T_C} = 225\left(\frac{T_i}{275.0} - 1\right).

  3. Write the total entropy change equation: ΔSuniv=225[Ti275.0−1−ln⁡(Ti275.0)]=14.85 J/K\Delta S_{\text{univ}} = 225\left[\frac{T_i}{275.0} - 1 - \ln\left(\frac{T_i}{275.0}\right)\right] = 14.85\text{ J}/\text{K}.

  4. Divide by 225 J/K225\text{ J}/\text{K} to obtain: x−1−ln⁡x=0.0660x - 1 - \ln x = 0.0660, where x=Ti275.0x = \frac{T_i}{275.0}.

  5. Solve for the ratio xx: for x=1.4007x = 1.4007, 1.4007−1−ln⁡(1.4007)≈0.06601.4007 - 1 - \ln(1.4007) \approx 0.0660, giving x≈1.4007x \approx 1.4007.

  6. Calculate Ti=1.4007×275.0 K≈385.2 KT_i = 1.4007 \times 275.0\text{ K} \approx 385.2\text{ K}.

Final answer

Ti=385.2 KT_i = 385.2\text{ K} (or 112.0∘C112.0^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the First Law sign convention: heat entering any reservoir or system is always algebraically positive.

  • Practice solving transcendental equations of the form x−1−ln⁡x=kx - 1 - \ln x = k using quick trial-and-error or linear interpolation.

  • Always perform a physical sanity check: spontaneous cooling into a colder reservoir must yield ΔSuniv>0\Delta S_{\text{univ}} > 0.

OverviewACEpath Teacher's Diagnosis

03 The student confuses the entropy change of the aluminum cylinder with the total entropy change of the universe, ignoring the entropy increase of the reservoir entirely.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    C=(0.250 kg)(900 J/(kg⋅K))=225 J/KC = (0.250\text{ kg})(900\text{ J}/(\text{kg}\cdot\text{K})) = 225\text{ J}/\text{K}

  2. Step 2

    ΔSuniv=ΔSAl=C⋅ln⁡(TC/Ti)\Delta S_{\text{univ}} = \Delta S_{\text{Al}} = C \cdot \ln(T_C / T_i)

    Correct

    ΔSuniv=ΔSAl+ΔSbath=Cln⁡(TCTi)+C(Ti−TC)TC\Delta S_{\text{univ}} = \Delta S_{\text{Al}} + \Delta S_{\text{bath}} = C \ln\left(\frac{T_C}{T_i}\right) + \frac{C(T_i - T_C)}{T_C}

    The universe comprises both the cooling cylinder and the thermal bath. During this irreversible process, the bath absorbs heat Q=C(Ti−TC)Q = C(T_i - T_C) at constant temperature TCT_C, so you must include ΔSbath=QTC\Delta S_{\text{bath}} = \frac{Q}{T_C} in the total entropy balance.

  3. Step 3

    14.85=225⋅ln⁡(275.0/Ti)  ⟹  ln⁡(275.0/Ti)=0.066  ⟹  275.0/Ti=e0.066≈1.0682  ⟹  Ti≈257.4 K14.85 = 225 \cdot \ln(275.0/T_i) \implies \ln(275.0/T_i) = 0.066 \implies 275.0/T_i = e^{0.066} \approx 1.0682 \implies T_i \approx 257.4\text{ K}

    Correct

    TiTC−1−ln⁡(TiTC)=ΔSunivC=0.0660  ⟹  TiTC≈1.4007  ⟹  Ti≈385.2 K\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right) = \frac{\Delta S_{\text{univ}}}{C} = 0.0660 \implies \frac{T_i}{T_C} \approx 1.4007 \implies T_i \approx 385.2\text{ K}

    Your algebraic manipulation was technically consistent with your setup, but omitting the reservoir term led to a physically impossible result where the initially hot cylinder (TiT_i) was calculated to be colder than the bath (257.4 K<275.0 K257.4\text{ K} < 275.0\text{ K}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the thermal heat capacity of the aluminum cylinder using C=mcC = m c.

You correctly remembered that the entropy change of a finite body with varying temperature is given by Cln⁡(Tf/Ti)C\ln(T_f/T_i).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitting Reservoir Entropy in Universe Balance

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the entropy change of the system as the total entropy change of the universe, forgetting that heat released by the system enters the surrounding thermal bath and increases the bath's entropy by ΔSbath=QTC\Delta S_{\text{bath}} = \frac{Q}{T_C}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Thermodynamic Universe
  • For any thermal interaction, ΔSuniv=ΔSsystem+ΔSsurroundings\Delta S_{\text{univ}} = \Delta S_{\text{system}} + \Delta S_{\text{surroundings}}.

  • Always identify both interacting bodies (here, the aluminum cylinder and the infinite reservoir) before writing the entropy sum.

Differentiate Finite Bodies and Constant-Temperature Reservoirs
  • For a finite body cooling or heating: ΔS=∫C dTT=Cln⁡(Tf/Ti)\Delta S = \int \frac{C\,dT}{T} = C\ln(T_f/T_i). For an isothermal reservoir at temperature TresT_{\text{res}}: ΔS=QabsorbedTres\Delta S = \frac{Q_{\text{absorbed}}}{T_{\text{res}}}.

  • Calculate the heat transferred into the reservoir Q=C(Ti−Tf)Q = C(T_i - T_f) and divide by its constant temperature.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the heat transferred from the cylinder into the bath: Q=C(Ti−TC)Q = C(T_i - T_C).

  2. Express the bath's entropy change: ΔSbath=QTC=C(TiTC−1)\Delta S_{\text{bath}} = \frac{Q}{T_C} = C\left(\frac{T_i}{T_C} - 1\right).

  3. Combine both contributions: ΔSuniv=C[TiTC−1−ln⁡(TiTC)]\Delta S_{\text{univ}} = C\left[\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right)\right].

  4. Substitute C=225.0 J/KC = 225.0\text{ J}/\text{K} and ΔSuniv=14.85 J/K\Delta S_{\text{univ}} = 14.85\text{ J}/\text{K} to obtain: TiTC−1−ln⁡(TiTC)=14.85225.0=0.0660\frac{T_i}{T_C} - 1 - \ln\left(\frac{T_i}{T_C}\right) = \frac{14.85}{225.0} = 0.0660.

  5. Let x=TiTCx = \frac{T_i}{T_C}; solve x−1−ln⁡x=0.0660x - 1 - \ln x = 0.0660 numerically to find x≈1.4007x \approx 1.4007.

  6. Multiply by TCT_C: Ti=1.4007×275.0 K≈385.2 KT_i = 1.4007 \times 275.0\text{ K} \approx 385.2\text{ K}.

Final answer

Ti≈385.2 KT_i \approx 385.2\text{ K} (112.0∘C112.0^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check physical plausibility: when a hot object cools down, its own entropy decreases (ΔSobject<0\Delta S_{\text{object}} < 0), so ΔSuniv>0\Delta S_{\text{univ}} > 0 is only possible if the reservoir gains entropy.

  • Practice setting up universe entropy equations for thermal equilibration problems involving both finite objects and infinite heat reservoirs.

Lock it in

Similar question

01

A copper block (C=150 J/KC = 150\text{ J}/\text{K}) at Ti=350 KT_i = 350\text{ K} is dropped into a large water bath maintained at TC=300 KT_C = 300\text{ K}. Calculate the total entropy change of the universe ΔSuniv\Delta S_{\text{univ}} when the block reaches equilibrium.

Answer

ΔSuniv≈1.81 J/K\Delta S_{\text{univ}} \approx 1.81\text{ J}/\text{K}. Steps: Heat transferred to the bath is Q=C(Ti−TC)=150(50)=7500 JQ = C(T_i - T_C) = 150(50) = 7500\text{ J}. Then ΔSbath=7500300=+25.0 J/K\Delta S_{\text{bath}} = \frac{7500}{300} = +25.0\text{ J}/\text{K}. For the block, ΔScopper=150ln⁡(300350)≈−23.12 J/K\Delta S_{\text{copper}} = 150\ln\left(\frac{300}{350}\right) \approx -23.12\text{ J}/\text{K}. Total: ΔSuniv=25.0−23.12=+1.88 J/K\Delta S_{\text{univ}} = 25.0 - 23.12 = +1.88\text{ J}/\text{K} (or 150[350/300−1−ln⁡(350/300)]≈1.81 J/K150[350/300 - 1 - \ln(350/300)] \approx 1.81\text{ J}/\text{K}).

02

An iron sphere (m=0.500 kgm = 0.500\text{ kg}, c=450 J/(kg⋅K)c = 450\text{ J}/(\text{kg}\cdot\text{K})) cools from TiT_i to TC=300 KT_C = 300\text{ K} in an infinite lake. The total entropy generation is measured as ΔSuniv=8.10 J/K\Delta S_{\text{univ}} = 8.10\text{ J}/\text{K}. Determine the initial temperature TiT_i.

Answer

Ti≈384 KT_i \approx 384\text{ K}. Steps: Total heat capacity C=mc=225 J/KC = mc = 225\text{ J}/\text{K}. The governing equation is ΔSunivC=x−1−ln⁡x\frac{\Delta S_{\text{univ}}}{C} = x - 1 - \ln x, where x=TiTCx = \frac{T_i}{T_C}. Thus x−1−ln⁡x=8.10225=0.0360x - 1 - \ln x = \frac{8.10}{225} = 0.0360. Solving x−1−ln⁡x=0.0360x - 1 - \ln x = 0.0360 yields x≈1.280x \approx 1.280. Therefore, Ti=1.280×300 K≈384 KT_i = 1.280 \times 300\text{ K} \approx 384\text{ K}.

03

Two identical finite metal blocks, each with constant heat capacity CC, have initial temperatures T1T_1 and T2T_2 and are brought into thermal contact inside an isolated container until they equilibrate. (a) Find the final temperature TfT_f. (b) Derive the total entropy change ΔSuniv\Delta S_{\text{univ}} and show that ΔSuniv≥0\Delta S_{\text{univ}} \ge 0 using the arithmetic-geometric mean inequality.

Answer

(a) Tf=T1+T22T_f = \frac{T_1 + T_2}{2} by conservation of energy. (b) ΔSuniv=ΔS1+ΔS2=Cln⁡(TfT1)+Cln⁡(TfT2)=Cln⁡(Tf2T1T2)=2Cln⁡((T1+T2)/2T1T2)\Delta S_{\text{univ}} = \Delta S_1 + \Delta S_2 = C\ln\left(\frac{T_f}{T_1}\right) + C\ln\left(\frac{T_f}{T_2}\right) = C\ln\left(\frac{T_f^2}{T_1 T_2}\right) = 2C\ln\left(\frac{(T_1 + T_2)/2}{\sqrt{T_1 T_2}}\right). By the AM-GM inequality, T1+T22≥T1T2\frac{T_1 + T_2}{2} \ge \sqrt{T_1 T_2}, so the argument of the logarithm is ≥1\ge 1, which proves ΔSuniv≥0\Delta S_{\text{univ}} \ge 0.

Loading workspace…