Resources

In a laboratory experiment investigating rotational equilibrium, students mount a meter stick on a central low-friction knife-edge support fixed at the 50.0 cm50.0\text{ cm} mark. Because the meter stick is slightly non-uniform, its center of mass is not at the geometric midpoint. When a calibrated tare mass of m1=50.0 gm_1 = 50.0\text{ g} is hung at the 15.0 cm15.0\text{ cm} mark, the system balances horizontally if an unknown mass m2m_2 is placed at the 75.0 cm75.0\text{ cm} mark. In a second trial with the knife-edge moved to the 40.0 cm40.0\text{ cm} mark, the bare meter stick alone (with no attached masses) balances horizontally with the knife-edge support at 40.0 cm40.0\text{ cm} when a single mass m3=20.0 gm_3 = 20.0\text{ g} is placed at the 10.0 cm10.0\text{ cm} mark. In a third calibration run, the knife-edge is returned to 50.0 cm50.0\text{ cm}, the tare mass m1=50.0 gm_1 = 50.0\text{ g} is moved to the 20.0 cm20.0\text{ cm} mark, and an electronic force probe connected vertically at the 90.0 cm90.0\text{ cm} mark pulls downward until the meter stick is perfectly horizontal. Calculate the downward force FpF_p recorded by the force probe. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

Fp=0.221 NF_p = 0.221\text{ N}

Steps

01

Find the gravitational torque of the meter stick from Trial 2

To find the downward force FpF_p measured by the force probe, apply the condition of static rotational equilibrium: the sum of torques about the pivot must equal zero (∑τ=0\sum \tau = 0).

In Trial 2, the bare meter stick is supported by a knife-edge at the 40.0 cm40.0\text{ cm} position and balances horizontally when a mass m3=20.0 g=0.0200 kgm_3 = 20.0\text{ g} = 0.0200\text{ kg} is hung at the 10.0 cm10.0\text{ cm} mark.

The lever arm for m3m_3 relative to the pivot is: d3=40.0 cm−10.0 cm=30.0 cm=0.300 md_3 = 40.0\text{ cm} - 10.0\text{ cm} = 30.0\text{ cm} = 0.300\text{ m}

Because m3m_3 is to the left of the pivot, it exerts a counterclockwise torque. For the bare stick to balance, its own weight must exert an equal clockwise torque τstick\tau_{\text{stick}}: τstick=m3gd3=(0.0200 kg)(9.80 m/s2)(0.300 m)=0.0588 N⋅m\tau_{\text{stick}} = m_3 g d_3 = (0.0200\text{ kg})(9.80\text{ m/s}^2)(0.300\text{ m}) = 0.0588\text{ N}\cdot\text{m}

(Note: Trial 1 involves an unknown mass m2m_2 not required for the calibration in Trial 3.)


02

Set up the torque balance for Trial 3

In Trial 3, the knife-edge support is restored to the 50.0 cm50.0\text{ cm} mark.

  1. Tare mass m1m_1:

    • Mass: m1=50.0 g=0.0500 kgm_1 = 50.0\text{ g} = 0.0500\text{ kg}
    • Position: 20.0 cm20.0\text{ cm}
    • Lever arm: d1=50.0 cm−20.0 cm=30.0 cm=0.300 md_1 = 50.0\text{ cm} - 20.0\text{ cm} = 30.0\text{ cm} = 0.300\text{ m}
    • This mass pulls downward to the left of the pivot, producing a counterclockwise torque: τ1=m1gd1=(0.0500 kg)(9.80 m/s2)(0.300 m)=0.1470 N⋅m\tau_1 = m_1 g d_1 = (0.0500\text{ kg})(9.80\text{ m/s}^2)(0.300\text{ m}) = 0.1470\text{ N}\cdot\text{m}
  2. Meter stick's inherent gravitational torque:

    • Acts in the clockwise direction: τstick=0.0588 N⋅m\tau_{\text{stick}} = 0.0588\text{ N}\cdot\text{m}
  3. Force probe FpF_p:

    • Position: 90.0 cm90.0\text{ cm}
    • Lever arm: dp=90.0 cm−50.0 cm=40.0 cm=0.400 md_p = 90.0\text{ cm} - 50.0\text{ cm} = 40.0\text{ cm} = 0.400\text{ m}
    • The probe pulls downward to the right of the pivot, producing an additional clockwise torque: τp=Fp⋅dp\tau_p = F_p \cdot d_p

03

Solve for the probe force FpF_p

Equating the counterclockwise torque to the total clockwise torque: τ1=τstick+Fpdp\tau_1 = \tau_{\text{stick}} + F_p d_p

Substitute the known values: 0.1470 N⋅m=0.0588 N⋅m+Fp(0.400 m)0.1470\text{ N}\cdot\text{m} = 0.0588\text{ N}\cdot\text{m} + F_p(0.400\text{ m})

Fp(0.400 m)=0.1470 N⋅m−0.0588 N⋅m=0.0882 N⋅mF_p(0.400\text{ m}) = 0.1470\text{ N}\cdot\text{m} - 0.0588\text{ N}\cdot\text{m} = 0.0882\text{ N}\cdot\text{m}

Fp=0.0882 N⋅m0.400 m=0.2205 N≈0.221 NF_p = \frac{0.0882\text{ N}\cdot\text{m}}{0.400\text{ m}} = 0.2205\text{ N} \approx 0.221\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes the meter stick is uniform and that its center of mass is located at the 50.0 cm mark, neglecting the torque contributed by the stick's own weight.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Στ=0 about pivot at 50.0 cm  ⟹  Fp∗(90.0−50.0)−m1∗g∗(50.0−20.0)=0\Sigma \tau = 0\text{ about pivot at } 50.0\text{ cm} \implies F_p * (90.0 - 50.0) - m_1 * g * (50.0 - 20.0) = 0

    Correct

    ∑τ=τ1−τstick−τp=0  ⟹  m1g(50.0−20.0)−τstick−Fp(90.0−50.0)=0\sum \tau = \tau_1 - \tau_{\text{stick}} - \tau_p = 0 \implies m_1 g (50.0 - 20.0) - \tau_{\text{stick}} - F_p(90.0 - 50.0) = 0

    You set up the torque balance assuming only the suspended mass m1m_1 and the probe force FpF_p act on the meter stick. Because the problem states that the stick is non-uniform and its center of mass is not at the geometric midpoint, the stick's own weight exerts a torque (determined in Trial 2 to be τstick=0.0588 N⋅m\tau_{\text{stick}} = 0.0588\text{ N}\cdot\text{m} in the clockwise direction) that must be included.

  2. Step 2

    Fp∗(40.0 cm)=(0.0500 kg)(9.80 m/s2)(30.0 cm)  ⟹  Fp∗0.400 m=0.147 N⋅m  ⟹  Fp=0.147/0.400=0.3675 N≈0.368 NF_p * (40.0\text{ cm}) = (0.0500\text{ kg})(9.80\text{ m/s}^2)(30.0\text{ cm}) \implies F_p * 0.400\text{ m} = 0.147\text{ N}\cdot\text{m} \implies F_p = 0.147 / 0.400 = 0.3675\text{ N} \approx 0.368\text{ N}

    Correct

    Fp(0.400 m)=0.1470 N⋅m−0.0588 N⋅m=0.0882 N⋅m  ⟹  Fp=0.08820.400≈0.221 NF_p(0.400\text{ m}) = 0.1470\text{ N}\cdot\text{m} - 0.0588\text{ N}\cdot\text{m} = 0.0882\text{ N}\cdot\text{m} \implies F_p = \frac{0.0882}{0.400} \approx 0.221\text{ N}

    Your algebraic rearrangement and arithmetic were carried out correctly, but the calculated value of FpF_p is incorrect due to the missing stick torque term from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You stated the rotational equilibrium condition ∑τ=0\sum \tau = 0 about the pivot at the 50.0 cm50.0\text{ cm} mark.

You correctly calculated the lever arm and torque produced by the 50.0 g50.0\text{ g} tare mass.

You performed the unit conversions and final algebraic calculations accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglecting Inherent Torque of Non-Uniform Body

No

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the meter stick as if it were uniform or massless with its center of gravity at the 50.0 cm50.0\text{ cm} pivot mark, ignoring the calibration information from Trial 2 that establishes the gravitational torque exerted by the stick itself.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for Non-Uniform Objects
  • Whenever an extended body is non-uniform, its center of mass is offset from the geometric center, meaning gravity exerts a net torque about the pivot unless the pivot is placed exactly at the center of mass.

  • Always identify whether a body's own weight contributes to torque, especially when calibration trials are provided to determine that inherent torque.

Trial Calibration Information
  • In multi-step laboratory problems, preliminary balancing trials are typically provided to calibrate an unknown parameter (such as stick mass or inherent torque) before analyzing the final setup.

  • Extract the torque or center of mass location from the preliminary trial before setting up the equilibrium equation for the main trial.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use Trial 2 to find the inherent torque of the meter stick: τstick=m3gd3=(0.0200 kg)(9.80 m/s2)(0.400 m−0.100 m)=0.0588 N⋅m\tau_{\text{stick}} = m_3 g d_3 = (0.0200\text{ kg})(9.80\text{ m/s}^2)(0.400\text{ m} - 0.100\text{ m}) = 0.0588\text{ N}\cdot\text{m} (clockwise).

  2. In Trial 3, equate counterclockwise and clockwise torques about the 50.0 cm50.0\text{ cm} pivot: τ1=τstick+Fpdp\tau_1 = \tau_{\text{stick}} + F_p d_p.

  3. Substitute the known torques: 0.1470 N⋅m=0.0588 N⋅m+Fp(0.400 m)0.1470\text{ N}\cdot\text{m} = 0.0588\text{ N}\cdot\text{m} + F_p(0.400\text{ m}).

  4. Solve for the probe force: Fp=0.1470−0.05880.400=0.08820.400=0.2205 N≈0.221 NF_p = \frac{0.1470 - 0.0588}{0.400} = \frac{0.0882}{0.400} = 0.2205\text{ N} \approx 0.221\text{ N}.

Final answer

Fp=0.221 NF_p = 0.221\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review Trial 2 to see why the bare stick required an external mass to balance, confirming that gravity exerts an unbalanced torque on it about the pivot.

  • Practice drawing free-body diagrams that explicitly show the gravitational force vector at the center of gravity of an extended object.

  • Solve the follow-up practice problems to master isolating inherent body torques in rotational equilibrium problems.

OverviewACEpath Teacher's Diagnosis

02 The student determines the magnitude of the stick's torque correctly from trial 2 but misidentifies its direction, adding it to the tare mass torque instead of balancing against it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    From trial 2: τstick=m3⋅g⋅(0.400−0.100)=(0.0200)(9.80)(0.300)=0.0588 N⋅m\text{From trial 2: } \tau_{\text{stick}} = m_3 \cdot g \cdot (0.400 - 0.100) = (0.0200)(9.80)(0.300) = 0.0588\text{ N}\cdot\text{m}

  2. Step 2

    Στ=0 about 50.0 cm pivot  ⟹  Fp⋅(0.900−0.500)=m1⋅g⋅(0.500−0.200)+τstick  ⟹  Fp⋅0.400=(0.0500)(9.80)(0.300)+0.0588  ⟹  Fp⋅0.400=0.1470+0.0588=0.2058 N⋅m\Sigma \tau = 0\text{ about } 50.0\text{ cm pivot} \implies F_p \cdot (0.900 - 0.500) = m_1 \cdot g \cdot (0.500 - 0.200) + \tau_{\text{stick}} \implies F_p \cdot 0.400 = (0.0500)(9.80)(0.300) + 0.0588 \implies F_p \cdot 0.400 = 0.1470 + 0.0588 = 0.2058\text{ N}\cdot\text{m}

    Correct

    τccw=τcw  ⟹  m1g(0.500−0.200)=Fp(0.900−0.500)+τstick  ⟹  0.1470 N⋅m=Fp(0.400 m)+0.0588 N⋅m\tau_{\text{ccw}} = \tau_{\text{cw}} \implies m_1 g (0.500 - 0.200) = F_p (0.900 - 0.500) + \tau_{\text{stick}} \implies 0.1470\text{ N}\cdot\text{m} = F_p(0.400\text{ m}) + 0.0588\text{ N}\cdot\text{m}

    Because the stick balanced in Trial 2 against mass m3m_3 placed to the left of the pivot, the stick's center of mass lies to the right, exerting a clockwise torque. In Trial 3, pulling downward at 90.0 cm90.0\text{ cm} also exerts a clockwise torque, while the tare mass at 20.0 cm20.0\text{ cm} exerts a counterclockwise torque. Therefore, τstick\tau_{\text{stick}} must be grouped on the clockwise side alongside FpdpF_p d_p, rather than added to the tare mass torque.

  3. Step 3

    Fp=0.2058/0.400=0.5145 N≈0.515 NF_p = 0.2058 / 0.400 = 0.5145\text{ N} \approx 0.515\text{ N}

    Correct

    Fp=0.1470−0.05880.400=0.08820.400=0.2205 N≈0.221 NF_p = \frac{0.1470 - 0.0588}{0.400} = \frac{0.0882}{0.400} = 0.2205\text{ N} \approx 0.221\text{ N}

    Your division and rounding were algebraically consistent with your torque equation, but the numerical result was affected by the sign error in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the system satisfies the rotational equilibrium condition Στ=0\Sigma \tau = 0.

You calculated the magnitude of the inherent torque of the stick as 0.0588 N⋅m0.0588\text{ N}\cdot\text{m} using the data from Trial 2.

You correctly calculated the lever arms for the tare mass (0.300 m0.300\text{ m}) and the force probe (0.400 m0.400\text{ m}) about the 50.0 cm50.0\text{ cm} pivot.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Torque direction misclassification

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the meter stick's inherent torque as an added counterclockwise torque instead of identifying which direction its weight tends to rotate the stick about the pivot.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish torque sense relative to the pivot
  • Forces acting downward to the left of a pivot produce counterclockwise torques, while downward forces to the right produce clockwise torques.

  • Always draw a quick free-body diagram and label each torque as clockwise (CW) or counterclockwise (CCW) before writing Στcw=Στccw\Sigma \tau_{\text{cw}} = \Sigma \tau_{\text{ccw}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Group torques by rotational direction about the 50.0 cm50.0\text{ cm} mark: τccw=τ1=m1g(0.300 m)=0.1470 N⋅m\tau_{\text{ccw}} = \tau_1 = m_1 g (0.300\text{ m}) = 0.1470\text{ N}\cdot\text{m}.

  2. Sum the clockwise torques: τcw=τstick+Fp(0.400 m)=0.0588 N⋅m+0.400Fp\tau_{\text{cw}} = \tau_{\text{stick}} + F_p (0.400\text{ m}) = 0.0588\text{ N}\cdot\text{m} + 0.400 F_p.

  3. Equate the two directions: 0.1470=0.0588+0.400Fp  ⟹  0.400Fp=0.0882 N⋅m0.1470 = 0.0588 + 0.400 F_p \implies 0.400 F_p = 0.0882\text{ N}\cdot\text{m}.

Final answer

Fp=0.221 NF_p = 0.221\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a horizontal axis showing the pivot position at 50.0 cm50.0\text{ cm} and indicate each downward force vector.

  • Verify that counteracting clockwise torques and counterclockwise torques appear on opposite sides of the equilibrium equation.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the lever arm of the force probe from the nearest end of the meter stick (100.0 cm) rather than from the knife-edge pivot at 50.0 cm.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τstick=(0.0200 kg)(9.80 m/s2)(0.300 m)=0.0588 N⋅m\tau_{\text{stick}} = (0.0200\text{ kg})(9.80\text{ m/s}^2)(0.300\text{ m}) = 0.0588\text{ N}\cdot\text{m}

  2. Step 2

    Fp⋅(1.000−0.900)+τstick=m1⋅g⋅(0.500−0.200)  ⟹  Fp⋅0.100+0.0588=(0.0500)(9.80)(0.300)F_p \cdot (1.000 - 0.900) + \tau_{\text{stick}} = m_1 \cdot g \cdot (0.500 - 0.200) \implies F_p \cdot 0.100 + 0.0588 = (0.0500)(9.80)(0.300)

    Correct

    Fp⋅(0.900−0.500)+τstick=m1⋅g⋅(0.500−0.200)  ⟹  Fp⋅0.400+0.0588=0.1470 N⋅mF_p \cdot (0.900 - 0.500) + \tau_{\text{stick}} = m_1 \cdot g \cdot (0.500 - 0.200) \implies F_p \cdot 0.400 + 0.0588 = 0.1470\text{ N}\cdot\text{m}

    You measured the lever arm of the force probe from the 100.0 cm100.0\text{ cm} end (1.000−0.900=0.100 m1.000 - 0.900 = 0.100\text{ m}) instead of from the knife-edge pivot at 50.0 cm50.0\text{ cm} (0.900−0.500=0.400 m0.900 - 0.500 = 0.400\text{ m}).

  3. Step 3

    Fp⋅0.100=0.1470−0.0588=0.0882 N⋅m  ⟹  Fp=0.08820.100=0.882 NF_p \cdot 0.100 = 0.1470 - 0.0588 = 0.0882\text{ N}\cdot\text{m} \implies F_p = \frac{0.0882}{0.100} = 0.882\text{ N}

    Correct

    Fp⋅0.400=0.0882 N⋅m  ⟹  Fp=0.08820.400≈0.221 NF_p \cdot 0.400 = 0.0882\text{ N}\cdot\text{m} \implies F_p = \frac{0.0882}{0.400} \approx 0.221\text{ N}

    Your algebraic rearrangement and arithmetic were carried out cleanly, but the final value was affected by the incorrect lever arm.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Trial 2 to find the stick's gravitational torque.

You correctly set the sum of clockwise torques equal to the sum of counterclockwise torques about the pivot.

You accurately calculated the lever arm and torque for the tare mass m1m_1.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Reference Point for Lever Arm

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You measured the distance of the force probe from the nearest end of the meter stick (100.0 cm100.0\text{ cm}) rather than finding its displacement from the chosen axis of rotation at the knife-edge pivot (50.0 cm50.0\text{ cm}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Lever Arm Definition
  • The lever arm dd is always measured from the chosen pivot point (axis of rotation) to the line of action of the force: d=∣xforce−xpivot∣d = |x_{\text{force}} - x_{\text{pivot}}|.

  • Always identify and mark xpivotx_{\text{pivot}} on your diagram first, then compute ∣x−xpivot∣|x - x_{\text{pivot}}| for every force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the correct lever arm for the force probe relative to the pivot at 50.0 cm50.0\text{ cm}: dp=0.900 m−0.500 m=0.400 md_p = 0.900\text{ m} - 0.500\text{ m} = 0.400\text{ m}.

  2. Substitute dp=0.400 md_p = 0.400\text{ m} into the torque balance equation: Fp(0.400 m)+0.0588 N⋅m=0.1470 N⋅mF_p(0.400\text{ m}) + 0.0588\text{ N}\cdot\text{m} = 0.1470\text{ N}\cdot\text{m}.

  3. Solve for FpF_p: Fp=0.1470−0.05880.400=0.08820.400=0.2205 N≈0.221 NF_p = \frac{0.1470 - 0.0588}{0.400} = \frac{0.0882}{0.400} = 0.2205\text{ N} \approx 0.221\text{ N}.

Final answer

Fp=0.221 NF_p = 0.221\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always double-check that every lever arm in ∑τ=0\sum \tau = 0 is referenced to the exact pivot position rather than the ruler's zero mark or end mark.

  • Sketch an arrow on the meter stick for each force, explicitly labeling the distance from the pivot to each force.

Lock it in

Similar question

01

A non-uniform meter stick is placed on a knife-edge pivot at the 50.0 cm50.0\text{ cm} mark. To keep it horizontal, a student hangs a 30.0 g30.0\text{ g} mass at the 10.0 cm10.0\text{ cm} mark. Calculate the magnitude and direction of the torque exerted by the meter stick's own weight about the 50.0 cm50.0\text{ cm} pivot. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

τstick=0.118 N⋅m\tau_{\text{stick}} = 0.118\text{ N}\cdot\text{m} (clockwise). Key steps:

  1. The added mass has lever arm d=50.0 cm−10.0 cm=0.400 md = 50.0\text{ cm} - 10.0\text{ cm} = 0.400\text{ m} on the left, creating a counterclockwise torque: τmass=(0.0300 kg)(9.80 m/s2)(0.400 m)=0.1176 N⋅m\tau_{\text{mass}} = (0.0300\text{ kg})(9.80\text{ m/s}^2)(0.400\text{ m}) = 0.1176\text{ N}\cdot\text{m}.
  2. For static equilibrium (∑τ=0\sum \tau = 0), the stick's own weight must exert an equal and opposite torque: τstick=0.118 N⋅m\tau_{\text{stick}} = 0.118\text{ N}\cdot\text{m} clockwise.
02

A non-uniform meter stick has an inherent clockwise gravitational torque of 0.0600 N⋅m0.0600\text{ N}\cdot\text{m} about the 50.0 cm50.0\text{ cm} mark. A student places a pivot at 50.0 cm50.0\text{ cm} and hangs a 40.0 g40.0\text{ g} mass at the 25.0 cm25.0\text{ cm} mark. At what position on the right side of the pivot should an upward force of 0.500 N0.500\text{ N} be applied to achieve horizontal balance? Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

The upward force cannot balance the stick on the right; it must be applied on the left at the 42.4 cm42.4\text{ cm} mark, or if pulled downward on the right, placed at the 57.6 cm57.6\text{ cm} mark (d=7.6 cmd = 7.6\text{ cm} from pivot). Key steps:

  1. Counterclockwise torque from left mass: τleft=(0.0400 kg)(9.80 m/s2)(0.250 m)=0.0980 N⋅m\tau_{\text{left}} = (0.0400\text{ kg})(9.80\text{ m/s}^2)(0.250\text{ m}) = 0.0980\text{ N}\cdot\text{m}.
  2. Stick's clockwise torque is 0.0600 N⋅m0.0600\text{ N}\cdot\text{m}. Net torque without the external force is 0.0980−0.0600=0.0380 N⋅m0.0980 - 0.0600 = 0.0380\text{ N}\cdot\text{m} counterclockwise.
  3. To balance, an additional clockwise torque of 0.0380 N⋅m0.0380\text{ N}\cdot\text{m} is required. A downward force on the right gives d=0.03800.500=0.076 m=7.6 cmd = \frac{0.0380}{0.500} = 0.076\text{ m} = 7.6\text{ cm}, so position is 57.6 cm57.6\text{ cm}.
03

A 1.00 m1.00\text{ m} non-uniform plank of total mass M=0.400 kgM = 0.400\text{ kg} balances horizontally on a pivot at the 45.0 cm45.0\text{ cm} mark when an unknown mass mm is suspended at the 10.0 cm10.0\text{ cm} mark and a 0.150 kg0.150\text{ kg} mass is hung at the 85.0 cm85.0\text{ cm} mark. When the pivot is moved to the 60.0 cm60.0\text{ cm} mark, the bare plank alone balances horizontally when a single 0.100 kg0.100\text{ kg} mass is placed at the 80.0 cm80.0\text{ cm} mark. Find the mass mm. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

m=0.0857 kgm = 0.0857\text{ kg} (or 85.7 g85.7\text{ g}). Key steps:

  1. From the second trial (pivot at 60.0 cm60.0\text{ cm}), the single mass is at 80.0 cm80.0\text{ cm} (lever arm 0.200 m0.200\text{ m} CW). Thus, the plank's center of mass xcmx_{\text{cm}} must be on the left (CCW): Mg(0.600−xcm)=(0.100)g(0.800−0.600)=0.0200gM g (0.600 - x_{\text{cm}}) = (0.100) g (0.800 - 0.600) = 0.0200 g. With M=0.400 kgM = 0.400\text{ kg}, 0.600−xcm=0.02000.400=0.050 m  ⟹  xcm=0.550 m=55.0 cm0.600 - x_{\text{cm}} = \frac{0.0200}{0.400} = 0.050\text{ m} \implies x_{\text{cm}} = 0.550\text{ m} = 55.0\text{ cm}.
  2. In the first setup (pivot at 45.0 cm45.0\text{ cm}): center of mass is at 55.0 cm55.0\text{ cm} (dcm=10.0 cmd_{\text{cm}} = 10.0\text{ cm} CW), mass 0.150 kg0.150\text{ kg} is at 85.0 cm85.0\text{ cm} (d=40.0 cmd = 40.0\text{ cm} CW), and mass mm is at 10.0 cm10.0\text{ cm} (dm=35.0 cmd_m = 35.0\text{ cm} CCW).
  3. Torque balance: m(0.350)=M(0.100)+0.150(0.400)=(0.400)(0.100)+0.060=0.100 kg⋅mm(0.350) = M(0.100) + 0.150(0.400) = (0.400)(0.100) + 0.060 = 0.100\text{ kg}\cdot\text{m}.
  4. Solve: m=0.1000.350=27 kg≈0.0857 kgm = \frac{0.100}{0.350} = \frac{2}{7}\text{ kg} \approx 0.0857\text{ kg}.
Loading workspace…