Resources

In a physics laboratory experiment utilizing a photogate timer system, a dynamic cart carrying a single flag of length L=5.00 cmL = 5.00\text{ cm} passes through two consecutive photogates spaced Δx=60.0 cm\Delta x = 60.0\text{ cm} apart along a low-friction air track. The electronic digital timer records a flag transit time of Δt1=0.0500 s\Delta t_1 = 0.0500\text{ s} at Photogate 1 and Δt2=0.0250 s\Delta t_2 = 0.0250\text{ s} at Photogate 2. (a) Extract all raw experimental measurements, convert them to standard SI units, and identify the inferred instantaneous speeds at each gate; (b) specify the unknown acceleration aexpa_{\text{exp}} across the track interval; and (c) compute the experimental acceleration aexpa_{\text{exp}}.

Answer and steps

Final answer

(a) Knowns: flag length L=0.0500 mL = 0.0500\text{ m}, photogate spacing Δx=0.600 m\Delta x = 0.600\text{ m}, gate 1 transit time Δt1=0.0500 s\Delta t_1 = 0.0500\text{ s} (yielding v1=1.00 m/sv_1 = 1.00\text{ m/s}), gate 2 transit time Δt2=0.0250 s\Delta t_2 = 0.0250\text{ s} (yielding v2=2.00 m/sv_2 = 2.00\text{ m/s}); (b) Unknown: experimental linear acceleration aexpa_{\text{exp}}; (c) aexp=2.50 m/s2a_{\text{exp}} = 2.50\text{ m/s}^2.

Steps

Part (a): Extract Known Quantities, Convert to SI Units, and Incur Speeds

From the problem statement, extract the directly measured values and convert centimeters to meters (1 m=100 cm1\text{ m} = 100\text{ cm}):

  • Flag length (LL): L=5.00 cm=0.0500 mL = 5.00\text{ cm} = 0.0500\text{ m}
  • Photogate separation distance (Δx\Delta x): Δx=60.0 cm=0.600 m\Delta x = 60.0\text{ cm} = 0.600\text{ m}
  • Transit time through Photogate 1 (Δt1\Delta t_1): Δt1=0.0500 s\Delta t_1 = 0.0500\text{ s}
  • Transit time through Photogate 2 (Δt2\Delta t_2): Δt2=0.0250 s\Delta t_2 = 0.0250\text{ s}

Because the flag length is small, the average speed of the flag as it passes through each photogate closely approximates the cart's instantaneous speed at that position:

  • Speed at Photogate 1 (v1v_1): v1=LΔt1=0.0500 m0.0500 s=1.00 m/sv_1 = \frac{L}{\Delta t_1} = \frac{0.0500\text{ m}}{0.0500\text{ s}} = 1.00\text{ m/s}
  • Speed at Photogate 2 (v2v_2): v2=LΔt2=0.0500 m0.0250 s=2.00 m/sv_2 = \frac{L}{\Delta t_2} = \frac{0.0500\text{ m}}{0.0250\text{ s}} = 2.00\text{ m/s}

Part (b): Identify the Unknown Quantity

  • Target unknown: The experimental linear acceleration, denoted as aexpa_{\text{exp}}, assumed constant across the interval between the two photogates.

Part (c): Compute the Experimental Acceleration (aexpa_{\text{exp}})

Using the kinematic relation relating initial velocity, final velocity, constant acceleration, and displacement independent of total transit time: v22=v12+2aexpΔxv_2^2 = v_1^2 + 2 a_{\text{exp}} \Delta x

Rearrange the equation to isolate aexpa_{\text{exp}}: aexp=v22−v122Δxa_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x}

Substitute the values: aexp=(2.00 m/s)2−(1.00 m/s)22(0.600 m)a_{\text{exp}} = \frac{(2.00\text{ m/s})^2 - (1.00\text{ m/s})^2}{2(0.600\text{ m})}

aexp=4.00−1.001.20 m/s2=3.001.20 m/s2=2.50 m/s2a_{\text{exp}} = \frac{4.00 - 1.00}{1.20}\text{ m/s}^2 = \frac{3.00}{1.20}\text{ m/s}^2 = 2.50\text{ m/s}^2

Common Pitfall: Be careful not to confuse the flag length LL with the distance between gates Δx\Delta x. The flag length LL is used only to calculate local speeds (v1v_1 and v2v_2) over each gate's short duration, whereas the gate separation distance Δx\Delta x is used in the kinematic equation to find the acceleration between the two gates.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the velocities when applying the kinematic relation relating distance, speed, and acceleration, using a = (v₂ - v₁) / (2·Δx) instead of a = (v₂² - v₁²) / (2·Δx).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    L=5.00 cm=0.0500 mL = 5.00\text{ cm} = 0.0500\text{ m}, Δx=60.0 cm=0.600 m\Delta x = 60.0\text{ cm} = 0.600\text{ m}, Δt1=0.0500 s\Delta t_1 = 0.0500\text{ s}, Δt2=0.0250 s\Delta t_2 = 0.0250\text{ s}

  2. Step 2

    v1=0.05000.0500=1.00 m/s  ⟹  v2=0.05000.0250=2.00 m/sv_1 = \frac{0.0500}{0.0500} = 1.00\text{ m/s} \implies v_2 = \frac{0.0500}{0.0250} = 2.00\text{ m/s}

  3. Step 3

    aexp=v2−v12⋅Δxa_{\text{exp}} = \frac{v_2 - v_1}{2 \cdot \Delta x}

    Correct

    v22=v12+2aexpΔx  ⟹  aexp=v22−v122Δxv_2^2 = v_1^2 + 2a_{\text{exp}}\Delta x \implies a_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x}

    When relating initial velocity, final velocity, acceleration, and displacement without elapsed time, the velocities must be squared according to the kinematic formula v22=v12+2aΔxv_2^2 = v_1^2 + 2a\Delta x.

  4. Step 4

    aexp=2.00−1.002⋅0.600=1.001.20=0.833 m/s2a_{\text{exp}} = \frac{2.00 - 1.00}{2 \cdot 0.600} = \frac{1.00}{1.20} = 0.833\text{ m/s}^2

    Correct

    aexp=(2.00 m/s)2−(1.00 m/s)22(0.600 m)=3.001.20 m/s2=2.50 m/s2a_{\text{exp}} = \frac{(2.00\text{ m/s})^2 - (1.00\text{ m/s})^2}{2(0.600\text{ m})} = \frac{3.00}{1.20}\text{ m/s}^2 = 2.50\text{ m/s}^2

    Your numerical evaluation followed your written formula correctly, but the final answer is incorrect due to the missing squared terms.

WHAT YOU DID WELL
Compliments from Your Teacher

You extracted all raw measurements and converted them into standard SI units correctly.

You applied the definition of average speed across the flag length to find the instantaneous velocity at each photogate.

You clearly identified the experimental acceleration as the unknown target variable.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinematic Formula Selection

You forgot to square the speeds v1v_1 and v2v_2 when isolating acceleration in terms of displacement.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the time-independent kinematic equation v2=v02+2aΔxv^2 = v_0^2 + 2a\Delta x with the linear acceleration definition a=ΔvΔta = \frac{\Delta v}{\Delta t}, leading to an unphysical blend where Δv\Delta v was divided by 2Δx2\Delta x.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check the Available Kinematic Variables
  • If you know initial speed, final speed, and position displacement without the transit time between positions, use vf2=vi2+2aΔxv_f^2 = v_i^2 + 2a\Delta x.

  • Before writing an isolated formula for acceleration, write out the base kinematic equation connecting your knowns (v1,v2,Δxv_1, v_2, \Delta x) and unknown (aa).

Perform a Dimensional Analysis Sanity Check
  • The units of both sides of an equation must match: [a]=m/s2[a] = \text{m/s}^2.

  • Notice that v2−v12Δx\frac{v_2 - v_1}{2\Delta x} has units m/sm=s−1\frac{\text{m/s}}{\text{m}} = \text{s}^{-1}, whereas v22−v122Δx\frac{v_2^2 - v_1^2}{2\Delta x} gives m2/s2m=m/s2\frac{\text{m}^2/\text{s}^2}{\text{m}} = \text{m/s}^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the time-independent constant acceleration relation: v22=v12+2aexpΔxv_2^2 = v_1^2 + 2a_{\text{exp}}\Delta x.

  2. Isolate aexpa_{\text{exp}} by subtracting v12v_1^2 and dividing by 2Δx2\Delta x: aexp=v22−v122Δxa_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x}.

  3. Substitute the numerical values: aexp=(2.00)2−(1.00)22(0.600)=4.00−1.001.20=3.001.20 m/s2a_{\text{exp}} = \frac{(2.00)^2 - (1.00)^2}{2(0.600)} = \frac{4.00 - 1.00}{1.20} = \frac{3.00}{1.20}\text{ m/s}^2.

Final answer

aexp=2.50 m/s2a_{\text{exp}} = 2.50\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the four standard constant-acceleration kinematic equations and list which variable is absent in each.

  • Always check units when creating a formula rearrangement from memory to prevent dimensional mismatches.

  • Practice solving photogate problems involving distance between gates versus flag length.

OverviewACEpath Teacher's Diagnosis

02 The student omits the factor of 2 in the denominator of the kinematic equation v² = v₀² + 2aΔx, using a = (v₂² - v₁²) / Δx.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    L=0.0500 m,Δx=0.600 m,Δt1=0.0500 s,Δt2=0.0250 sL = 0.0500\text{ m}, \Delta x = 0.600\text{ m}, \Delta t_1 = 0.0500\text{ s}, \Delta t_2 = 0.0250\text{ s}

  2. Step 2

    v1=0.05000.0500=1.00 m/s  ⟹  v2=0.05000.0250=2.00 m/sv_1 = \frac{0.0500}{0.0500} = 1.00\text{ m/s} \implies v_2 = \frac{0.0500}{0.0250} = 2.00\text{ m/s}

  3. Step 3

    aexp=v22−v12Δxa_{\text{exp}} = \frac{v_2^2 - v_1^2}{\Delta x}

    Correct

    aexp=v22−v122Δxa_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x}

    You crossed out the factor of 22 in the denominator. Starting from v22=v12+2aΔxv_2^2 = v_1^2 + 2a\Delta x, subtracting v12v_1^2 gives v22−v12=2aΔxv_2^2 - v_1^2 = 2a\Delta x, so dividing both sides by 2Δx2\Delta x yields a=v22−v122Δxa = \frac{v_2^2 - v_1^2}{2\Delta x}.

  4. Step 4

    aexp=2.002−1.0020.600=3.000.600=5.00 m/s2a_{\text{exp}} = \frac{2.00^2 - 1.00^2}{0.600} = \frac{3.00}{0.600} = 5.00\text{ m/s}^2

    Correct

    aexp=2.002−1.0022(0.600)=3.001.20=2.50 m/s2a_{\text{exp}} = \frac{2.00^2 - 1.00^2}{2(0.600)} = \frac{3.00}{1.20} = 2.50\text{ m/s}^2

    Because the denominator missed the factor of 22, your calculated acceleration is twice the correct value.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted all centimeter values into SI meters correctly.

You used the ratio of flag length to gate passage time to find gate velocities.

You performed accurate arithmetic on your written expressions.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinematic Formula Rearrangement Error

You initially wrote (2Δx)(2\Delta x) in the denominator, but then crossed it out in favor of Δx\Delta x.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the kinematic work-energy relation v2−v02=2aΔxv^2 - v_0^2 = 2a\Delta x with a linear rate of change or forgot that isolating acceleration requires dividing by the entire coefficient (2Δx)(2\Delta x).

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinematic Equation Isolation
  • v22=v12+2aΔx  ⟹  a=v22−v122Δxv_2^2 = v_1^2 + 2a\Delta x \implies a = \frac{v_2^2 - v_1^2}{2\Delta x}

  • Always write down the base equation v2=v02+2aΔxv^2 = v_0^2 + 2a\Delta x first and divide by (2Δx)(2\Delta x) in a single explicit algebraic step.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. aexp=v22−v122Δxa_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x}

  2. aexp=(2.00 m/s)2−(1.00 m/s)22(0.600 m)=4.00−1.001.200 m/s2a_{\text{exp}} = \frac{(2.00\text{ m/s})^2 - (1.00\text{ m/s})^2}{2(0.600\text{ m})} = \frac{4.00 - 1.00}{1.200}\text{ m/s}^2

  3. aexp=3.001.20 m/s2=2.50 m/s2a_{\text{exp}} = \frac{3.00}{1.20}\text{ m/s}^2 = 2.50\text{ m/s}^2

Final answer

aexp=2.50 m/s2a_{\text{exp}} = 2.50\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the derivation of v2=v02+2aΔxv^2 = v_0^2 + 2a\Delta x from work-energy theorem (Wnet=FΔx=maΔx=12mv2−12mv02W_{\text{net}} = F\Delta x = ma\Delta x = \frac{1}{2}m v^2 - \frac{1}{2}m v_0^2) to remember where the factor of 2 originates.

  • Practice rearranging kinematic equations algebraically before plugging in numbers.

OverviewACEpath Teacher's Diagnosis

03 The student misinterprets the transit time difference Δt₂ - Δt₁ as the travel time between the two photogates and uses a = Δv / Δt.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    L=0.0500 m,Δx=0.600 m,Δt1=0.0500 s,Δt2=0.0250 sL = 0.0500\text{ m},\quad \Delta x = 0.600\text{ m},\quad \Delta t_1 = 0.0500\text{ s},\quad \Delta t_2 = 0.0250\text{ s}

  2. Step 2

    v1=0.05000.0500=1.00 m/s  ⟹  v2=0.05000.0250=2.00 m/sv_1 = \frac{0.0500}{0.0500} = 1.00\text{ m/s} \implies v_2 = \frac{0.0500}{0.0250} = 2.00\text{ m/s}

  3. Step 3

    ttravel=Δt1−Δt2=0.0500−0.0250=0.0250 st_{\text{travel}} = \Delta t_1 - \Delta t_2 = 0.0500 - 0.0250 = 0.0250\text{ s}

    Correct

    Use v22=v12+2aexpΔxv_2^2 = v_1^2 + 2a_{\text{exp}}\Delta x because the elapsed time between the two photogates is unknown.

    The recorded times Δt1\Delta t_1 and Δt2\Delta t_2 represent how long the flag physically blocked the infrared beam at each individual gate, not clock timestamps along the track. Subtracting them does not yield the time taken to travel the separation distance Δx\Delta x.

  4. Step 4

    aexp=v2−v1ttravel=2.00−1.000.0250=40.0 m/s2a_{\text{exp}} = \frac{v_2 - v_1}{t_{\text{travel}}} = \frac{2.00 - 1.00}{0.0250} = 40.0\text{ m/s}^2

    Correct

    aexp=v22−v122Δx=(2.00)2−(1.00)22(0.600)=2.50 m/s2a_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x} = \frac{(2.00)^2 - (1.00)^2}{2(0.600)} = 2.50\text{ m/s}^2

    Because your travel time was conceptually invalid, the resulting acceleration calculation was thrown off.

WHAT YOU DID WELL
Compliments from Your Teacher

You extracted all raw measurements and properly converted centimeters to meters.

You correctly calculated the instantaneous speeds at both photogate locations using the flag length.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time interval confusion between gate occlusion and inter-gate transit

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the individual gate transit durations (time taken for the flag to clear a single optical beam) with clock readings along the track, assuming their difference equaled the travel time across the inter-gate distance Δx\Delta x. Because the travel time between photogates was neither measured nor provided, you should have used the time-independent kinematic relation v22=v12+2aΔxv_2^2 = v_1^2 + 2a\Delta x.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish Flag Transit Time vs. Inter-Gate Travel Time
  • A photogate timer measuring Δtgate\Delta t_{\text{gate}} records only the time the beam is blocked by the flag of length LL, which gives local speed v≈L/Δtgatev \approx L / \Delta t_{\text{gate}}. It does not measure the transit time across the distance Δx\Delta x between two separated gates.

  • Check whether a time value represents an occlusion duration at a single point or the flight time across the separation distance. If the inter-gate travel time is not given, select a kinematic formula that does not require time, such as vf2=vi2+2aΔxv_f^2 = v_i^2 + 2a\Delta x.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the known kinematic variables across the interval: v1=1.00 m/sv_1 = 1.00\text{ m/s}, v2=2.00 m/sv_2 = 2.00\text{ m/s}, and Δx=0.600 m\Delta x = 0.600\text{ m}.

  2. Select the kinematic equation linking initial velocity, final velocity, acceleration, and displacement independent of time: v22=v12+2aexpΔxv_2^2 = v_1^2 + 2a_{\text{exp}}\Delta x.

  3. Rearrange to solve for acceleration: aexp=v22−v122Δxa_{\text{exp}} = \frac{v_2^2 - v_1^2}{2\Delta x}.

  4. Substitute the numerical values: aexp=(2.00 m/s)2−(1.00 m/s)22(0.600 m)=4.00−1.001.20 m/s2=2.50 m/s2a_{\text{exp}} = \frac{(2.00\text{ m/s})^2 - (1.00\text{ m/s})^2}{2(0.600\text{ m})} = \frac{4.00 - 1.00}{1.20}\text{ m/s}^2 = 2.50\text{ m/s}^2.

Final answer

aexp=2.50 m/s2a_{\text{exp}} = 2.50\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between a local duration (blocking time) and an interval duration (travel time between two distinct points).

  • Practice selecting kinematic equations based on which variable (time, distance, or acceleration) is omitted.

  • Work through the flashcards and practice problems below to master photogate kinematic analysis.

Lock it in

Similar question

01

A glider on an air track passes through two photogates separated by Δx=0.80 m\Delta x = 0.80\text{ m}. Its speed is 0.40 m/s0.40\text{ m/s} at the first gate and 1.20 m/s1.20\text{ m/s} at the second gate. Assuming constant acceleration, find aa.

Answer

a=0.80 m/s2a = 0.80\text{ m/s}^2. Using v22=v12+2aΔxv_2^2 = v_1^2 + 2a\Delta x, we have a=(1.20)2−(0.40)22(0.80)=1.44−0.161.60=1.281.60=0.80 m/s2a = \frac{(1.20)^2 - (0.40)^2}{2(0.80)} = \frac{1.44 - 0.16}{1.60} = \frac{1.28}{1.60} = 0.80\text{ m/s}^2.

02

A cart with a flag of length L=2.0 cmL = 2.0\text{ cm} accelerates uniformly down an inclined track. It takes 0.040 s0.040\text{ s} to pass through Gate 1 and 0.010 s0.010\text{ s} to pass through Gate 2. If the photogates are spaced 0.75 m0.75\text{ m} apart, determine the cart's acceleration.

Answer

a=2.5 m/s2a = 2.5\text{ m/s}^2. First compute speeds: v1=0.020 m0.040 s=0.50 m/sv_1 = \frac{0.020\text{ m}}{0.040\text{ s}} = 0.50\text{ m/s} and v2=0.020 m0.010 s=2.00 m/sv_2 = \frac{0.020\text{ m}}{0.010\text{ s}} = 2.00\text{ m/s}. Then a=v22−v122Δx=(2.00)2−(0.50)22(0.75)=4.00−0.251.50=3.751.50=2.5 m/s2a = \frac{v_2^2 - v_1^2}{2\Delta x} = \frac{(2.00)^2 - (0.50)^2}{2(0.75)} = \frac{4.00 - 0.25}{1.50} = \frac{3.75}{1.50} = 2.5\text{ m/s}^2.

03

A dynamic cart starts from rest and passes a photogate after traveling a distance d1=0.20 md_1 = 0.20\text{ m} with constant acceleration a=1.6 m/s2a = 1.6\text{ m/s}^2. A second photogate is located at distance d2=0.70 md_2 = 0.70\text{ m} from rest. Calculate the change in speed Δv=v2−v1\Delta v = v_2 - v_1 between the two gates.

Answer

Δv=0.70 m/s\Delta v = 0.70\text{ m/s}. From v2=2adv^2 = 2ad, v1=2(1.6)(0.20)=0.64=0.80 m/sv_1 = \sqrt{2(1.6)(0.20)} = \sqrt{0.64} = 0.80\text{ m/s}, and v2=2(1.6)(0.70)=2.24≈1.50 m/sv_2 = \sqrt{2(1.6)(0.70)} = \sqrt{2.24} \approx 1.50\text{ m/s}. Therefore, Δv=1.50−0.80=0.70 m/s\Delta v = 1.50 - 0.80 = 0.70\text{ m/s}.

Loading workspace…