Resources
A lead bullet with a mass of is fired horizontally at a speed of into a stationary, thermally insulated wooden block of mass initially resting on a frictionless surface. The bullet embeds completely into the block in a completely inelastic collision. If exactly of the mechanical energy lost during the collision is retained inside the bullet as internal thermal energy (with negligible heat conducted into the wood during impact), calculate the resulting temperature rise of the lead bullet. The specific heat capacity of lead is .
Answer and steps
Final answer
Steps
Determine the final velocity of the combined system
Since no external horizontal forces act on the system during the collision, total horizontal linear momentum is conserved:
Substitute the given values into the equation to find the common velocity immediately after the impact:
Calculate the mechanical energy lost during the collision
The initial mechanical energy is entirely the kinetic energy of the incoming bullet:
The final kinetic energy of the embedded bullet and block together is:
The mechanical energy lost (converted into internal thermal energy) is:
(Pitfall to avoid: Do not assume all initial kinetic energy is lost. Because the block moves on a frictionless surface, the system must retain a small amount of kinetic energy to satisfy conservation of linear momentum.)
Calculate the thermal energy absorbed by the bullet
According to the problem, of the lost mechanical energy is converted into internal thermal energy within the bullet:
Calculate the temperature increase of the bullet
The relationship between the thermal energy absorbed and the temperature change is given by:
Rearranging for :
Typical errors
01 The student assumes all initial kinetic energy of the bullet is lost as heat, completely ignoring the remaining kinetic energy of the moving block and bullet system.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the block rests on a frictionless surface, linear momentum is conserved during the collision. The combined block and bullet move forward with speed , retaining of kinetic energy, so only is converted into other forms.
- Step 3Correct
You applied the conversion ratio correctly, but the result is affected by using the unreduced initial kinetic energy.
- Step 4Correct
You used the heat capacity formula correctly, but the numerical answer is shifted by the earlier energy discrepancy.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the initial kinetic energy of the bullet as .
You properly applied the relationship between thermal energy, mass, specific heat, and temperature change: .
You correctly extracted the energy-retention fraction for the bullet.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the collision as if the target was fixed or brought to a complete stop, setting . However, on a frictionless surface, momentum conservation requires the combined system to move after the completely inelastic collision, retaining a non-zero final kinetic energy .
REASONING PATH
Your ACEpath teacher’s suggested approach- Momentum Check
In an isolated horizontal collision, total linear momentum is always conserved: .
Always solve for the final system velocity before calculating energy changes.
- Energy Loss Definition
The mechanical energy lost in an inelastic collision is , never simply unless the target is rigidly anchored.
Calculate and subtract it from to find the energy dissipated as heat.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the final common velocity using conservation of momentum: .
Find the remaining kinetic energy of the combined system: .
Determine the mechanical energy lost: .
Find thermal energy absorbed by the bullet: .
Solve for temperature rise: .
02 The student uses the total combined mass of the block and bullet instead of just the bullet mass in the final thermal heat equation Q = m * c * ΔT.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You substituted the total system mass () instead of the bullet's mass (). Because the problem specifies that the thermal energy is retained inside the lead bullet and heat conduction into the wood is negligible, only the bullet warms up.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used conservation of horizontal momentum to determine the common velocity after the inelastic collision.
You calculated both the initial kinetic energy and the final system kinetic energy accurately.
You took the correct fraction of lost mechanical energy to find the heat absorbed.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou knew the collision involved both objects, but you overlooked that only the bullet absorbs the heat and changes temperature.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIn the formula , the mass must correspond strictly to the substance whose specific heat capacity and temperature change are being measured. Since only the bullet absorbs this thermal energy and lead's specific heat capacity was used, must be the bullet's mass (), not the combined mass of the block and bullet.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match Mass to Material
In , the mass must be the exact mass of the specific object absorbing the heat .
Always verify which object receives the heat energy before picking the mass for the calorimetry formula.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the heat absorbed by the lead bullet: .
Set up the thermal energy equation using only the mass of the lead bullet: .
Solve for the temperature rise: .
03 The student forgets to square the velocity when computing the initial kinetic energy of the bullet.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the square on velocity in the kinetic energy formula, writing rather than .
- Step 3
- Step 4Correct
Because your initial kinetic energy was mistakenly calculated as smaller than the final kinetic energy, you reversed the difference and obtained an incorrect value for the lost mechanical energy and absorbed heat.
- Step 5Correct
Your formula and substitution for temperature change were mathematically sound, but they carried forward the incorrect value of from Step 4.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used conservation of linear momentum to determine the common post-collision speed.
You remembered to square the velocity when computing the system's final kinetic energy.
You correctly identified and applied the heat transfer relationship .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of , dropping the exponent on velocity.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing linear momentum () and kinetic energy () or overlooking the exponent during initial algebraic setup. Notice that this led to an impossible physical result ( in a completely inelastic collision), which prompted you to subtract rather than .
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinetic Energy Exponent Check
Translational kinetic energy is proportional to the square of velocity: .
Always write down the general formula with the term before substituting numerical values.
- Physical Reality Check for Inelastic Collisions
In an inelastic collision without internal sources of energy, mechanical energy is always lost: .
If your calculated is ever smaller than , pause immediately and check your kinetic energy expressions.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the correct initial kinetic energy: .
Determine the mechanical energy lost: .
Calculate the thermal energy transferred to the bullet: .
Solve for the temperature rise: .
Lock it in
In a completely inelastic collision between an object of mass and a free-to-move stationary object of mass , is all initial kinetic energy lost?
No. Momentum must be conserved, so the combined mass moves with , keeping .
Similar question
A lead bullet travels at and strikes an immovable, rigidly anchored steel plate, coming completely to rest. If of the initial kinetic energy is absorbed as thermal energy by the bullet, find the temperature rise of the bullet ().
Answer
. Because the plate is fixed, and . Heat absorbed is . Thus, .
A lead bullet () at embeds into a stationary wooden block on a frictionless floor. If of the mechanical energy lost is retained as heat in the bullet, calculate the bullet's temperature increase .
Answer
Total mass is . By momentum conservation, . Initial kinetic energy is , and final kinetic energy is . Mechanical energy lost is . Thermal energy in the bullet is . Hence, .
A copper slug () moving at hits a stationary block on a frictionless surface. The slug embeds into the block. If all lost mechanical energy is shared between the slug and block such that the slug's temperature rises by , what percentage of the lost mechanical energy was absorbed by the slug?
Answer
By momentum conservation, . Energy values: , , giving . The thermal energy absorbed by the slug is . Percentage retained is .