Resources

A sensitive experimental sensor modeled as a resistor Rs=50.0 ΩR_s = 50.0\,\Omega has a maximum allowable power dissipation threshold of Pmax⁡=2.00 WP_{\max} = 2.00\text{ W}, beyond which thermal degradation occurs. The sensor is wired in parallel with a ballast resistor Rb=75.0 ΩR_b = 75.0\,\Omega. This parallel pair is connected in series with a current-limiting resistor Rlimit=20.0 ΩR_{\text{limit}} = 20.0\,\Omega to a variable DC voltage supply. Calculate the maximum safe operating voltage Vmax⁡V_{\max} of the power supply such that the sensor operates exactly at its critical power threshold without burning out.

Answer and steps

Final answer

Vmax⁡=16.7 VV_{\max} = 16.7\text{ V}

Steps

01

Find the maximum allowable voltage across the sensor

To find the maximum safe supply voltage Vmax⁡V_{\max}, we determine the maximum permissible voltage across the sensor and then use the circuit's series-parallel voltage relationships to find the total supply voltage.

The electrical power PP dissipated in a resistor is related to the voltage across it, VpV_p, and its resistance, RsR_s, by: P=Vp2RsP = \frac{V_p^2}{R_s}

Solving for the maximum voltage VpV_p across the sensor: Vp=Pmax⁡⋅Rs=2.00 W⋅50.0 Ω=100 V2=10.0 VV_p = \sqrt{P_{\max} \cdot R_s} = \sqrt{2.00\text{ W} \cdot 50.0\,\Omega} = \sqrt{100\text{ V}^2} = 10.0\text{ V}

Because the ballast resistor RbR_b is connected in parallel with the sensor RsR_s, the voltage across both components is identical: Vparallel=Vp=10.0 VV_{\text{parallel}} = V_p = 10.0\text{ V}

02

Determine the equivalent resistance of the parallel branch

The equivalent resistance RpR_p of the parallel combination of RsR_s and RbR_b is given by: Rp=Rs⋅RbRs+Rb=50.0 Ω⋅75.0 Ω50.0 Ω+75.0 Ω=3750125.0 Ω=30.0 ΩR_p = \frac{R_s \cdot R_b}{R_s + R_b} = \frac{50.0\,\Omega \cdot 75.0\,\Omega}{50.0\,\Omega + 75.0\,\Omega} = \frac{3750}{125.0}\,\Omega = 30.0\,\Omega

03

Relate the parallel voltage to the total supply voltage

The total resistance of the circuit includes the current-limiting series resistor RlimitR_{\text{limit}}: Rtotal=Rlimit+Rp=20.0 Ω+30.0 Ω=50.0 ΩR_{\text{total}} = R_{\text{limit}} + R_p = 20.0\,\Omega + 30.0\,\Omega = 50.0\,\Omega

Using the voltage divider formula, the voltage across the parallel combination is a fraction of the total supply voltage Vmax⁡V_{\max}: Vp=Vmax⁡(RpRtotal)V_p = V_{\max} \left(\frac{R_p}{R_{\text{total}}}\right)

Substitute the known values into the equation: 10.0 V=Vmax⁡(30.0 Ω50.0 Ω)10.0\text{ V} = V_{\max} \left(\frac{30.0\,\Omega}{50.0\,\Omega}\right)

10.0 V=0.600⋅Vmax⁡10.0\text{ V} = 0.600 \cdot V_{\max}

Solving for Vmax⁡V_{\max}: Vmax⁡=10.0 V0.600≈16.7 VV_{\max} = \frac{10.0\text{ V}}{0.600} \approx 16.7\text{ V}

(Common Pitfall: Do not calculate the total circuit power simply by adding the rated powers of the components; the ballast resistor and series resistor each dissipate power proportional to their actual operating voltages and currents, governed by Kirchhoff's laws rather than individual independent ratings.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the equivalent resistance by incorrectly adding the parallel resistors in series, leading to an incorrect total resistance and supply voltage.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Vp=Pmax⁡⋅Rs=2.00⋅50.0=10.0 VV_p = \sqrt{P_{\max} \cdot R_s} = \sqrt{2.00 \cdot 50.0} = 10.0\text{ V}

  2. Step 2

    Rp=Rs+Rb=50.0+75.0=125 ΩR_p = R_s + R_b = 50.0 + 75.0 = 125\,\Omega

    Correct

    Rp=Rs⋅RbRs+Rb=50.0 Ω⋅75.0 Ω50.0 Ω+75.0 Ω=30.0 ΩR_p = \frac{R_s \cdot R_b}{R_s + R_b} = \frac{50.0\,\Omega \cdot 75.0\,\Omega}{50.0\,\Omega + 75.0\,\Omega} = 30.0\,\Omega

    You added the resistances directly as if they were in series. Because the sensor and the ballast resistor are wired in parallel, their equivalent resistance must follow the parallel combination rule: 1Rp=1Rs+1Rb\frac{1}{R_p} = \frac{1}{R_s} + \frac{1}{R_b}.

  3. Step 3

    Rtotal=Rp+Rlimit=125+20.0=145 ΩR_{\text{total}} = R_p + R_{\text{limit}} = 125 + 20.0 = 145\,\Omega

    Correct

    Rtotal=Rp+Rlimit=30.0 Ω+20.0 Ω=50.0 ΩR_{\text{total}} = R_p + R_{\text{limit}} = 30.0\,\Omega + 20.0\,\Omega = 50.0\,\Omega

    Your series addition logic here is correct, but the numerical result is affected by the incorrect value of RpR_p from the previous step.

  4. Step 4

    I=VpRs=10.050.0=0.20 AI = \frac{V_p}{R_s} = \frac{10.0}{50.0} = 0.20\text{ A}

  5. Step 5

    Vmax⁡=I⋅Rtotal=0.20⋅145=29.0 VV_{\max} = I \cdot R_{\text{total}} = 0.20 \cdot 145 = 29.0\text{ V}

    Correct

    Vmax⁡=Itotal⋅Rtotal=(VpRp)⋅Rtotal=(10.0 V30.0 Ω)⋅50.0 Ω≈16.7 VV_{\max} = I_{\text{total}} \cdot R_{\text{total}} = \left(\frac{V_p}{R_p}\right) \cdot R_{\text{total}} = \left(\frac{10.0\text{ V}}{30.0\,\Omega}\right) \cdot 50.0\,\Omega \approx 16.7\text{ V}

    You used the sensor's individual branch current 0.20 A0.20\text{ A} as the total circuit current. In a parallel circuit, total current splits between branches, so Itotal=Is+Ib=0.20 A+0.133 A=0.333 AI_{\text{total}} = I_s + I_b = 0.20\text{ A} + 0.133\text{ A} = 0.333\text{ A} (or Vp/RpV_p / R_p).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the maximum permissible voltage across the sensor using V=PRV = \sqrt{P R}.

You correctly found the current passing through the sensor branch.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Parallel resistance formula applied as series sum

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated parallel and series rules: you added parallel resistors using the direct series addition formula Rs+RbR_s + R_b, and you assumed that the branch current through the sensor equals the total current entering the entire circuit.

REASONING PATH
Your ACEpath teacher’s suggested approach
Parallel Equivalent Resistance
  • For two resistors in parallel, 1Rp=1R1+1R2  ⟹  Rp=R1R2R1+R2\frac{1}{R_p} = \frac{1}{R_1} + \frac{1}{R_2} \implies R_p = \frac{R_1 R_2}{R_1 + R_2}. The equivalent resistance is always strictly less than the smallest individual resistor.

  • Always apply the reciprocal formula to parallel branches before adding them in series with other resistors.

Kirchhoff's Current Law at Branch Junctions
  • Total current into a parallel junction equals the sum of branch currents: Itotal=I1+I2+⋯=VparallelRpI_{\text{total}} = I_1 + I_2 + \dots = \frac{V_{\text{parallel}}}{R_p}.

  • Do not multiply a single branch current by the total circuit resistance to find total voltage; use either the total junction current or a voltage-divider ratio.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate equivalent resistance of the parallel branch: Rp=Rs⋅RbRs+Rb=50.0⋅75.050.0+75.0=30.0 ΩR_p = \frac{R_s \cdot R_b}{R_s + R_b} = \frac{50.0 \cdot 75.0}{50.0 + 75.0} = 30.0\,\Omega.

  2. Find total circuit resistance: Rtotal=Rp+Rlimit=30.0+20.0=50.0 ΩR_{\text{total}} = R_p + R_{\text{limit}} = 30.0 + 20.0 = 50.0\,\Omega.

  3. Determine total supply current or use the voltage-divider rule: Itotal=VpRp=10.0 V30.0 Ω=13 AI_{\text{total}} = \frac{V_p}{R_p} = \frac{10.0\text{ V}}{30.0\,\Omega} = \frac{1}{3}\text{ A}.

  4. Calculate maximum supply voltage: Vmax⁡=Itotal⋅Rtotal=(13 A)⋅50.0 Ω≈16.7 VV_{\max} = I_{\text{total}} \cdot R_{\text{total}} = \left(\frac{1}{3}\text{ A}\right) \cdot 50.0\,\Omega \approx 16.7\text{ V}.

Final answer

Vmax⁡≈16.7 VV_{\max} \approx 16.7\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice combining two parallel resistors using the product-over-sum rule before adding series elements.

  • Check that your equivalent resistance for a parallel pair is always smaller than both individual resistors (e.g., 30.0 Ω<50.0 Ω30.0\,\Omega < 50.0\,\Omega).

  • Use the voltage divider formula Vp=Vtotal⋅RpRp+RseriesV_p = V_{\text{total}} \cdot \frac{R_p}{R_p + R_{\text{series}}} when finding source voltages in combination circuits.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to take the square root when finding voltage from power and resistance, using V = P · R instead of V = √(P · R).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Vp=Pmax⁡⋅Rs=2.00⋅50.0=100 VV_p = P_{\max} \cdot R_s = 2.00 \cdot 50.0 = 100\text{ V}

    Correct

    Vp=Pmax⁡⋅Rs=2.00 W⋅50.0 Ω=10.0 VV_p = \sqrt{P_{\max} \cdot R_s} = \sqrt{2.00\text{ W} \cdot 50.0\,\Omega} = 10.0\text{ V}

    You multiplied power by resistance directly. Since electrical power is given by P=V2RP = \frac{V^2}{R}, the voltage across the sensor is V=P⋅RV = \sqrt{P \cdot R}, requiring a square root.

  2. Step 2

    1Rp=150.0+175.0=5150  ⟹  Rp=30.0 Ω\frac{1}{R_p} = \frac{1}{50.0} + \frac{1}{75.0} = \frac{5}{150} \implies R_p = 30.0\,\Omega

  3. Step 3

    Rtotal=30.0+20.0=50.0 ΩR_{\text{total}} = 30.0 + 20.0 = 50.0\,\Omega

  4. Step 4

    Vmax⁡=Vp⋅RtotalRp=100⋅(50.030.0)=167 VV_{\max} = V_p \cdot \frac{R_{\text{total}}}{R_p} = 100 \cdot \left(\frac{50.0}{30.0}\right) = 167\text{ V}

    Correct

    Vmax⁡=Vp⋅RtotalRp=10.0 V⋅(50.0 Ω30.0 Ω)≈16.7 VV_{\max} = V_p \cdot \frac{R_{\text{total}}}{R_p} = 10.0\text{ V} \cdot \left(\frac{50.0\,\Omega}{30.0\,\Omega}\right) \approx 16.7\text{ V}

    Your voltage-scaling relationship is entirely correct, but substituting Vp=100 VV_p = 100\text{ V} instead of 10.0 V10.0\text{ V} carried the earlier error into your final result.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the equivalent resistance of the parallel branch as 30.0 Ω30.0\,\Omega.

You combined the series current-limiting resistance to find the total resistance of 50.0 Ω50.0\,\Omega.

You accurately set up and applied the voltage divider ratio to relate parallel branch voltage to supply voltage.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula misuse: power-voltage relationship

You wrote V=P⋅RV = P \cdot R rather than V=P⋅RV = \sqrt{P \cdot R}, omitting the square root required by P=V2RP = \frac{V^2}{R}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the power formula P=V2RP = \frac{V^2}{R} with Ohm's law V=I⋅RV = I \cdot R, leading to an unrooted product P⋅RP \cdot R for voltage.

REASONING PATH
Your ACEpath teacher’s suggested approach
Power-Voltage Relation
  • Power in terms of voltage and resistance is P=V2RP = \frac{V^2}{R}, which yields V2=P⋅RV^2 = P \cdot R.

  • Always isolate VV by taking the square root: V=P⋅RV = \sqrt{P \cdot R}.

Dimensional Unit Check
  • The product of power and resistance has units of W⋅Ω=(V2Ω)⋅Ω=V2\text{W} \cdot \Omega = \left(\frac{\text{V}^2}{\Omega}\right) \cdot \Omega = \text{V}^2.

  • Check your units; if an expression has units of V2\text{V}^2, take the square root to obtain volts.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the relationship between power, voltage, and resistance: Pmax⁡=Vp2RsP_{\max} = \frac{V_p^2}{R_s}.

  2. Solve for VpV_p: Vp=Pmax⁡⋅Rs=2.00 W⋅50.0 Ω=100 V2=10.0 VV_p = \sqrt{P_{\max} \cdot R_s} = \sqrt{2.00\text{ W} \cdot 50.0\,\Omega} = \sqrt{100\text{ V}^2} = 10.0\text{ V}.

  3. Apply the voltage divider relation using your correct equivalent resistances: Vmax⁡=Vp⋅RtotalRp=10.0 V⋅50.0 Ω30.0 Ω=16.7 VV_{\max} = V_p \cdot \frac{R_{\text{total}}}{R_p} = 10.0\text{ V} \cdot \frac{50.0\,\Omega}{30.0\,\Omega} = 16.7\text{ V}.

Final answer

Vmax⁡=16.7 VV_{\max} = 16.7\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the three standard Joule heating formulas: P=IVP = IV, P=I2RP = I^2 R, and P=V2RP = \frac{V^2}{R}.

  • Before substituting numbers, explicitly write out the algebraic variable you are solving for (e.g., V=PRV = \sqrt{PR}).

  • Perform a quick dimensional sanity check to ensure you do not equate volts directly with watts times ohms.

OverviewACEpath Teacher's Diagnosis

03 The student assumes the sensor's current equals the total circuit current, neglecting the branch current bypassed by the parallel ballast resistor.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Vp=2.00⋅50.0=10.0 V  ⟹  Is=2.0050.0=0.20 AV_p = \sqrt{2.00 \cdot 50.0} = 10.0\text{ V} \implies I_s = \sqrt{\frac{2.00}{50.0}} = 0.20\text{ A}

  2. Step 2

    Itotal=Is=0.20 AI_{\text{total}} = I_s = 0.20\text{ A}

    Correct

    Itotal=Is+Ib=0.20 A+10.0 V75.0 Ω=13 A≈0.333 AI_{\text{total}} = I_s + I_b = 0.20\text{ A} + \frac{10.0\text{ V}}{75.0\,\Omega} = \frac{1}{3}\text{ A} \approx 0.333\text{ A}

    Because the ballast resistor RbR_b is connected in parallel with the sensor, the total supply current splits between both branches according to Kirchhoff's Current Law. You equated ItotalI_{\text{total}} directly to IsI_s, neglecting the current Ib=10.0 V75.0 Ω≈0.133 AI_b = \frac{10.0\text{ V}}{75.0\,\Omega} \approx 0.133\text{ A} through the ballast branch.

  3. Step 3

    Vlimit=Itotal⋅Rlimit=0.20⋅20.0=4.0 VV_{\text{limit}} = I_{\text{total}} \cdot R_{\text{limit}} = 0.20 \cdot 20.0 = 4.0\text{ V}

    Correct

    Vlimit=Itotal⋅Rlimit=13 A⋅20.0 Ω≈6.67 VV_{\text{limit}} = I_{\text{total}} \cdot R_{\text{limit}} = \frac{1}{3}\text{ A} \cdot 20.0\,\Omega \approx 6.67\text{ V}

    Your application of Ohm's law was structurally correct, but the value is affected by the underestimated total current.

  4. Step 4

    Vmax⁡=Vp+Vlimit=10.0+4.0=14.0 VV_{\max} = V_p + V_{\text{limit}} = 10.0 + 4.0 = 14.0\text{ V}

    Correct

    Vmax⁡=Vp+Vlimit=10.0 V+6.67 V≈16.7 VV_{\max} = V_p + V_{\text{limit}} = 10.0\text{ V} + 6.67\text{ V} \approx 16.7\text{ V}

    Your loop summation using Kirchhoff's Voltage Law was set up correctly, but the final numerical result is affected by the earlier current error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the sensor's maximum allowable voltage and current from its power rating.

You correctly recognized that the total supply voltage equals the sum of the parallel section voltage and the series resistor voltage.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglecting parallel branch current

You equated the total line current to the sensor branch current instead of adding the current flowing through the parallel ballast resistor.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating a parallel branch current as the entire circuit current. In a circuit where components share a parallel junction, the main series current equals the sum of currents across all parallel paths (Itotal=∑IbranchI_{\text{total}} = \sum I_{\text{branch}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Branch Currents at Junctions
  • By Kirchhoff's Current Law, total current entering a parallel bank equals the sum of currents through every branch: Itotal=I1+I2+⋯+InI_{\text{total}} = I_1 + I_2 + \dots + I_n.

  • Always check whether a branch is in parallel before carrying its current forward into series components.

Alternative Method: Parallel Equivalent Resistance
  • A parallel pair can be condensed into a single resistor Rp=R1R2R1+R2R_p = \frac{R_1 R_2}{R_1 + R_2}, allowing you to use a standard voltage divider: Vp=Vtotal(RpRp+Rseries)V_p = V_{\text{total}} \left(\frac{R_p}{R_p + R_{\text{series}}}\right).

  • Calculate RpR_p first to avoid managing separate branch currents.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the current through the ballast branch: Ib=VpRb=10.0 V75.0 Ω=215 A≈0.133 AI_b = \frac{V_p}{R_b} = \frac{10.0\text{ V}}{75.0\,\Omega} = \frac{2}{15}\text{ A} \approx 0.133\text{ A}.

  2. Find the total circuit current entering the parallel network: Itotal=Is+Ib=0.20 A+215 A=13 A≈0.333 AI_{\text{total}} = I_s + I_b = 0.20\text{ A} + \frac{2}{15}\text{ A} = \frac{1}{3}\text{ A} \approx 0.333\text{ A}.

  3. Calculate the voltage drop across RlimitR_{\text{limit}}: Vlimit=Itotal⋅Rlimit=13 A⋅20.0 Ω≈6.67 VV_{\text{limit}} = I_{\text{total}} \cdot R_{\text{limit}} = \frac{1}{3}\text{ A} \cdot 20.0\,\Omega \approx 6.67\text{ V}.

  4. Apply Kirchhoff's Voltage Law to find total supply voltage: Vmax⁡=Vp+Vlimit=10.0 V+6.67 V=16.7 VV_{\max} = V_p + V_{\text{limit}} = 10.0\text{ V} + 6.67\text{ V} = 16.7\text{ V}.

Final answer

Vmax⁡≈16.7 VV_{\max} \approx 16.7\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice combining Kirchhoff's Current Law with Ohm's law at multi-branch nodes before computing series voltage drops.

  • Verify your answers on combination circuits by comparing your branch-current sum with the equivalent-resistance method (Rtotal=Rp+RseriesR_{\text{total}} = R_p + R_{\text{series}}).

Lock it in

Similar question

01

A 30.0 Ω30.0\,\Omega resistor and a 60.0 Ω60.0\,\Omega resistor are connected in parallel. This combination is connected in series with a 10.0 Ω10.0\,\Omega resistor to a DC power supply. If the voltage across the parallel combination is 12.0 V12.0\text{ V}, what is the total voltage supplied by the DC source?

Answer

18.0 V18.0\text{ V}. First, find equivalent parallel resistance Rp=30.0×60.030.0+60.0=20.0 ΩR_p = \frac{30.0 \times 60.0}{30.0 + 60.0} = 20.0\,\Omega. Total resistance is Rtotal=20.0 Ω+10.0 Ω=30.0 ΩR_{\text{total}} = 20.0\,\Omega + 10.0\,\Omega = 30.0\,\Omega. Using the voltage divider relation, Vsource=Vp⋅RtotalRp=12.0 V⋅30.0 Ω20.0 Ω=18.0 VV_{\text{source}} = V_p \cdot \frac{R_{\text{total}}}{R_p} = 12.0\text{ V} \cdot \frac{30.0\,\Omega}{20.0\,\Omega} = 18.0\text{ V}.

02

A device rated at R1=40.0 ΩR_1 = 40.0\,\Omega has a maximum operating current of 0.250 A0.250\text{ A}. It is placed in parallel with a shunt resistor R2=10.0 ΩR_2 = 10.0\,\Omega, and the combination is placed in series with an 8.00 Ω8.00\,\Omega ballast resistor. Calculate the maximum supply voltage VsupplyV_{\text{supply}} that will not exceed the current rating of the device.

Answer

18.0 V18.0\text{ V}. Maximum voltage across R1R_1 is Vp=I1R1=0.250 A×40.0 Ω=10.0 VV_p = I_1 R_1 = 0.250\text{ A} \times 40.0\,\Omega = 10.0\text{ V}. Current through R2R_2 is I2=10.0 V10.0 Ω=1.00 AI_2 = \frac{10.0\text{ V}}{10.0\,\Omega} = 1.00\text{ A}. Total circuit current is Itotal=0.250 A+1.00 A=1.25 AI_{\text{total}} = 0.250\text{ A} + 1.00\text{ A} = 1.25\text{ A}. The voltage across the ballast resistor is Vballast=1.25 A×8.00 Ω=10.0 VV_{\text{ballast}} = 1.25\text{ A} \times 8.00\,\Omega = 10.0\text{ V}. Therefore, Vsupply=Vp+Vballast=10.0 V+10.0 V=20.0 VV_{\text{supply}} = V_p + V_{\text{ballast}} = 10.0\text{ V} + 10.0\text{ V} = 20.0\text{ V}.

03

A sensor with resistance Rs=100 ΩR_s = 100\,\Omega is rated for a maximum power of 1.44 W1.44\text{ W}. It is wired in parallel with a resistor RbR_b. This parallel network is wired in series with a resistor Rc=15.0 ΩR_c = 15.0\,\Omega across a 24.0 V24.0\text{ V} supply. Determine the required resistance RbR_b so that the sensor dissipates exactly its maximum rated power.

Answer

30.0 Ω30.0\,\Omega. Maximum voltage across the sensor is Vp=Pmax⁡Rs=1.44×100=12.0 VV_p = \sqrt{P_{\max} R_s} = \sqrt{1.44 \times 100} = 12.0\text{ V}. The remaining supply voltage appears across RcR_c: Vc=24.0 V−12.0 V=12.0 VV_c = 24.0\text{ V} - 12.0\text{ V} = 12.0\text{ V}. Total current through RcR_c is Itotal=12.0 V15.0 Ω=0.80 AI_{\text{total}} = \frac{12.0\text{ V}}{15.0\,\Omega} = 0.80\text{ A}. The current through the sensor is Is=12.0 V100 Ω=0.12 AI_s = \frac{12.0\text{ V}}{100\,\Omega} = 0.12\text{ A}. Therefore, the ballast current is Ib=Itotal−Is=0.80 A−0.12 A=0.68 AI_b = I_{\text{total}} - I_s = 0.80\text{ A} - 0.12\text{ A} = 0.68\text{ A}. Thus, Rb=12.0 V0.68 A≈17.6 ΩR_b = \frac{12.0\text{ V}}{0.68\text{ A}} \approx 17.6\,\Omega.

Loading workspace…