Resources
Two identical in-phase audio speakers, separated by a distance of , emit a pure tone at a frequency of . A listener stands along the line joining the two speakers at a distance from the first speaker. Taking the speed of sound in air to be , calculate the minimum non-zero distance from the first speaker toward the second speaker where the listener experiences completely destructive interference.
Answer and steps
Final answer
Steps
Calculate the Wavelength
To find the location of destructive interference, we determine the wavelength of the sound waves and relate the path difference from the two sources to the condition for destructive interference.
The relationship between wave speed , frequency , and wavelength is:
Substituting the given values:
Formulate the Path Difference
Let the first speaker be located at the origin and the second speaker at .
For a listener standing between the speakers at a position along the line connecting them:
- Distance from the first speaker:
- Distance from the second speaker:
The path length difference between the two waves arriving at the listener is:
Condition for Destructive Interference
Because the two speakers emit in phase, destructive interference occurs whenever the path difference corresponds to an odd half-integer number of wavelengths:
The primary (minimum path-difference) condition for destructive interference occurs at :
Solve for the Position
Setting the path difference to the fundamental destructive interference condition:
For positions closer to the first speaker than the midpoint (), :
Thus, the location corresponding to this destructive interference condition is .
Typical errors
01 The student confuses destructive interference with constructive interference by setting the path difference to an integer multiple of the wavelength instead of an odd half-wavelength.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You set the path difference equal to an integer multiple of the wavelength (). That is the condition for constructive interference (waves arriving in phase). For completely destructive interference of two identical in-phase sources, the path difference must be an odd half-integer number of wavelengths, .
- Step 3Correct
Your algebra was carried out correctly according to your equation, but the numerical result is affected by the incorrect interference condition in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the wave relationship to find the wavelength.
You correctly set up the geometric path difference between the two speakers.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou applied the condition for constructive interference () rather than destructive interference.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the phase conditions: identical in-phase sources reinforce each other when their path difference is a whole number of wavelengths (), whereas they cancel out completely when their path difference is an odd half-wavelength, .
REASONING PATH
Your ACEpath teacher’s suggested approach- Recall Interference Conditions for In-Phase Sources
For two in-phase coherent sources, constructive interference occurs when , and destructive interference occurs when for .
Always verify whether the problem asks for maximum intensity (constructive) or cancellation/silence (destructive) before setting up the path difference equation.
- Identify the Fundamental Destructive Node
The smallest positive path difference producing complete cancellation is (the case).
Set to find the destructive interference node closest to the center.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the path difference to the fundamental destructive interference condition: .
For , remove the absolute value: .
Solve for : .
02 The student assumes the minimum non-zero distance corresponds to the fundamental order m = 0 (path difference of 0.5λ) instead of the order that places the node closest to the first speaker.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You set the path difference to the fundamental order , which minimizes the path difference and finds the node closest to the center (). To minimize the distance from the first speaker, you must maximize the path difference within the allowed separation , which corresponds to .
- Step 3Correct
Your algebraic rearrangement was carried out correctly on your equation, but the setup value was carried over from the incorrect interference order.
- Step 4Correct
Your final position follows algebraically from the incorrect equation. Solving with the maximum path difference condition yields .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the wavelength of the sound waves as .
You correctly formulated the path difference expression along the line connecting the two speakers as .
You performed accurate algebraic manipulations to solve your linear equation.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated minimizing the position coordinate with minimizing the path difference .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisAlong the line between two speakers, the path difference is zero at the center () and reaches its maximum near each speaker ( or ). Therefore, a point close to the first speaker corresponds to a large path difference, not the smallest one (). To find the node closest to the first speaker, you must choose the largest odd half-integer multiple of that is strictly less than .
REASONING PATH
Your ACEpath teacher’s suggested approach- Path Difference vs. Position
For points between two in-phase sources, increases as approaches .
Always check whether minimizing requires maximizing or minimizing before choosing the order .
- Physical Bounds on Orders
The path difference between two emitters separated by distance cannot exceed : .
List all allowed half-integer multiples and select the one that matches the requested physical boundary.
CORRECTED PATH
ACEpath Teacher's DemonstrationDestructive interference occurs when the path difference satisfies for .
Because for , making as small as possible requires making as large as possible without exceeding .
With , test the odd half-multiples: . The largest value smaller than is (order ).
Set , giving , so .
03 The student misinterprets the path difference between the two sources as simply x instead of |d - 2x|.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You equated the path difference directly to the distance from the first speaker. Because the listener stands between the two speakers at distance from speaker 1 and from speaker 2, the true path difference is .
- Step 3Correct
Solving for the closest node to the first speaker gives , so .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the wavelength of the sound wave.
You identified that destructive interference for two in-phase sources requires a path difference of .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the listener's position as the difference in path lengths between the two sources, overlooking that sound travels distances and from speakers placed at opposite ends of the line segment.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Individual Path Lengths
For a point between two collinear sources separated by distance , the distances to the sources are and .
Always write down both distances and explicitly before taking their difference .
CORRECTED PATH
ACEpath Teacher's DemonstrationExpress the distance from the listener to each speaker: and .
Write the path length difference: .
Set equal to the minimum destructive interference condition: .
Solve for : .
Lock it in
For two in-phase coherent wave sources, what is the condition for completely destructive interference in terms of path difference ?
for . An odd half-wavelength path difference aligns crests with troughs, causing total cancellation.
Similar question
Two in-phase speakers are separated by and emit sound waves of wavelength . A listener walks along the line between them starting from the midpoint. How far from the midpoint is the first point of completely destructive interference?
Answer
. At the midpoint, (constructive). For destructive interference, the path difference must be , so the distance from the midpoint is .
Two in-phase speakers emitting a pure tone of frequency are placed apart. The speed of sound is . Find the position closest to the midpoint () where complete destructive interference occurs.
Answer
(or ). First, . Destructive interference requires . Setting yields (and by symmetry, ).
Two speakers driven in phase are separated by and emit sound with . How many points of completely destructive interference exist strictly between the two speakers?
Answer
10 points. Along the line between the speakers, the path difference satisfies . Destructive interference requires . The possible values are , giving exactly 10 distinct locations.