Resources
A heavy rock of mass is being pried up using a rigid steel bar of fixed total length . A worker places a small stone as a fulcrum at a variable distance from the rock (), such that the effort arm length is . Taking : (a) write the analytical expression for the required effort force as a function of for horizontal static equilibrium, assuming the bar is massless, (b) calculate the asymptotic limit and explain its physical interpretation, and (c) find the maximum allowable fulcrum distance if the worker can apply a maximum downward effort force of only .
Answer and steps
Final answer
(a) ; (b) ; (c)
Steps
Part (a): Derive the Expression for the Effort Force
- Calculate the downward load force:
The force exerted by the rock due to gravity is: - Apply the condition for rotational static equilibrium:
Choosing the fulcrum as the pivot point eliminates the normal force exerted by the fulcrum from the torque equation. For the lever to remain balanced horizontally, the net torque about the fulcrum must be zero: -
Substitute the respective lever arm lengths:
The load arm has length , and the effort arm has length :Solving for :
Part (b): Asymptotic Limit and Physical Interpretation
- Evaluate the limit as :
- Physical interpretation:
As the fulcrum moves closer to the rock (), the load arm approaches zero while the effort arm approaches the full length of the bar (). The mechanical advantage: approaches infinity (). Consequently, the required effort force drops toward zero because a minuscule force applied over a very long lever arm can balance a massive force acting over a vanishingly small lever arm. (In practice, this requires the effort end to move an extremely large distance to lift the rock by a negligible height).
Part (c): Determine the Maximum Allowable Fulcrum Distance
- Set up the inequality:
The worker can supply at most . To maintain equilibrium without exceeding this force: - Solve for :
Since , the denominator is strictly positive. Multiply both sides by :
Thus, the maximum fulcrum distance from the rock is:
Typical errors
01 The student confuses mass with weight by omitting gravitational acceleration g when calculating torque, resulting in an effort force understated by a factor of 9.8.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You balanced torque using mass () instead of the gravitational force (). Torque requires force times perpendicular distance, so mass must be converted to weight.
- Step 2
, accompanied by the written explanation that the vanishing load arm allows a zero effort force to balance the load.
- Step 3Correct
Your algebraic method for solving the equation was completely sound, but your result of was affected by carrying over the unmultiplied mass coefficient from part (a) instead of using the force .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the fulcrum as the pivot and set up the torque balance equation.
You correctly identified the effort arm as and the load arm as .
You correctly interpreted the asymptotic behavior of the lever as .
You executed the algebraic steps to isolate cleanly and accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the mass value of into the torque equation instead of calculating the downward gravitational force .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing mass with gravitational force (weight) when applying Newton's laws and rotational equilibrium. Mass is an intrinsic measure of inertia measured in kilograms, while torque is produced by a force measured in newtons ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Torque Dimensions
Torque has dimensions of (), never ().
Always convert mass to weight () before inserting it into a torque balance equation.
- Unit Consistency Check
Both sides of a static equilibrium equation must share identical physical units.
Notice that has units of , while has units of . Multiply mass by to ensure both sides are in .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the load force: .
Equate counter-clockwise and clockwise torques about the fulcrum: .
Express effort force as a function of : .
Set : .
Combine like terms: , which gives .
(a) ; (b) ; (c)
02 The student inverts the lever arms in the torque balance equation, assigning the effort arm length to the load and the load arm length to the effort.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly found the load force , but you swapped the lever arms. Since the fulcrum is placed at distance from the rock, the load arm is and the effort arm is . Setting torque balance about the fulcrum gives .
- Step 2
As approaches 0, the effort arm becomes zero, requiring infinite effort force to lift the rock.
CorrectAs , the load arm shrinks to zero while the effort arm approaches , so the mechanical advantage approaches infinity and the required effort force approaches zero.
Your limit evaluation is mathematically consistent with your expression from part (a), but it is physically reversed because of the inverted lever arms. As , the fulcrum moves directly under the rock, making the load arm vanish while leaving the effort arm at , which drives the required effort force to .
- Step 3Correct
You solved the linear equation accurately based on your formula, but propagating the swapped expression resulted in instead of the correct value .
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the gravitational load force accurately as .
You correctly recognized that static rotational equilibrium requires balancing opposing torques about the fulcrum.
You executed all downstream algebraic steps cleanly, including isolating variables and clearing denominators.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou matched distance with and distance with , which is the exact opposite of the physical geometry defined in the problem.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou likely associated the variable by default with the effort force side rather than tracing each perpendicular distance directly from the pivot to the respective line of action.
REASONING PATH
Your ACEpath teacher’s suggested approach- Label distances relative to the pivot
In torque balance , every lever arm is strictly the distance from the chosen pivot to the specific force's line of action: .
Always sketch the beam, mark the pivot, and write the distance directly underneath each force before formulating the torque equation.
- Perform an extreme-case sanity check
Placing the pivot right next to a heavy load () gives maximum mechanical advantage, making lifting effortless.
Check whether your formula yields when the load arm approaches zero. If it yields infinity, your lever arms are inverted.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the torque balance using the correct lever arms: .
Substitute and to isolate : .
Take the limit as : .
Set to find : .
(a) ; (b) ; (c)
03 The student uses the total length L instead of the effort arm length L - x in the torque balance, treating the effort arm as the whole bar.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You used the total length of the bar as the effort arm. In a Class 1 lever, the lever arms must be measured from the fulcrum: the load arm is , so the remaining effort arm is .
- Step 3
, with the explanation that when the fulcrum is at the rock, the load arm is zero, requiring zero effort force.
Correct, because the load arm vanishes while the effort arm approaches , making mechanical advantage approach infinity.
You arrived at the correct limit value of and gave sound physical intuition about the vanishing load arm, though you evaluated the limit using your incorrect expression from part (a).
- Step 4Correct
Your algebraic solving technique for was executed correctly, but the numerical answer was affected by the missing denominator from part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the gravitational load force using .
You recognized that rotational equilibrium requires balancing opposing torques about the pivot.
You accurately identified that a vanishing load arm leads to an effort force approaching zero.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the entire bar length instead of the distance between the fulcrum and the effort application point, .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the total length of the lever with the effort lever arm. In torque balance equations, every lever arm must be measured strictly from the chosen pivot point (the fulcrum) to the line of action of each force.
REASONING PATH
Your ACEpath teacher’s suggested approach- Define arms relative to the fulcrum
For a lever of total length with an interior fulcrum at distance from one end, the two arms must sum to the total length: .
Always draw a quick diagram and label both segments from the pivot: load arm , effort arm .
- Torque equilibrium formulation
Static rotational equilibrium requires , meaning about the fulcrum.
Set before isolating .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the net torque about the fulcrum to zero: .
Substitute and to get .
Solve for : .
Set and cross-multiply: .
Combine like terms: , giving .
(a) ; (b) ; (c)
Lock it in
What is the key difference between mass and weight when setting up a static equilibrium equation?
Mass is the amount of matter in kilograms (), whereas weight is the gravitational force in newtons (). Torque equations require forces, so mass must be multiplied by .
Similar question
A uniform plank is balanced on a pivot. A box of mass is placed to the left of the pivot. What downward force must be applied to the right of the pivot to maintain horizontal equilibrium? (Take .)
Answer
. Steps: Calculate the box's weight . Apply rotational equilibrium : , yielding .
A crowbar of total length is used to lift a crate of mass . The fulcrum is located a distance from the crate. If a worker can apply a maximum force of at the opposite end, find the maximum fulcrum distance from the crate. (Take .)
Answer
(or ). Steps: . Torque balance: .
A non-uniform lever of length has its own mass with its center of mass located from the left end. A load of mass rests at the far left end (). A fulcrum is placed at . Calculate the downward effort force needed at the far right end () to keep the lever balanced. (Take .)
Answer
. Steps: Take torques about the fulcrum at . Counter-clockwise torque from the load: . Clockwise torque from the bar's weight (acting at , lever arm ): . Clockwise torque from effort (lever arm ): . Equating torques: .