Resources
A slider starts from rest at the top of a curved track at a vertical height above the floor and slides without friction down to a horizontal rough corridor where . Across this corridor, the slider collides head-on with an uncompressed horizontal bumper spring of force constant . The rough surface extends under the spring as well. Due to physical stop constraints, the spring can safely compress to a maximum threshold of . Using , calculate the minimum sliding distance on the rough flat track before the block contacts the spring such that the spring compression does not exceed .
Answer and steps
Final answer
Steps
Identify the Initial Mechanical Energy
The slider starts from rest at height on a frictionless track. Taking the horizontal floor as the reference level for gravitational potential energy (), the initial total mechanical energy is purely gravitational potential energy:
Substituting the given values:
Because the curved track is frictionless, the slider reaches the bottom horizontal surface with this entire amount of energy in kinetic form.
Determine the Energy Stored in the Spring
When the spring reaches its maximum allowable compression , the slider comes momentarily to rest (). The elastic potential energy stored in the spring is:
Substituting the known parameters:
Apply the Work-Energy Theorem Across the Rough Corridor
On the horizontal surface, the normal force exerted by the track balances gravity:
The constant kinetic friction force opposing the motion is:
As the block slides across the corridor, mechanical energy is dissipated as thermal energy through the work of friction. The energy of the slider must be reduced sufficiently before and during contact so that the spring does not compress beyond .
Accounting for the energy dissipation required along the pre-contact sliding distance :
Solving for the minimum distance :
Summary and Pitfall to Avoid
- Common Pitfall: Forgetting that friction continues to act while the spring is compressing. If the rough surface extends under the spring, friction dissipates energy over the distance as well as along the compression displacement . Always check whether the surface under the spring is specified as rough or frictionless.
Typical errors
01 The student forgets that the rough surface extends under the spring and only calculates the work done by friction over distance d, omitting the additional compression distance x_max.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4
- Step 5Correct
You equated the total rough travel distance directly to . Because the rough surface extends under the spring, friction continues to oppose motion over the compression distance , making the total rough distance .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the initial gravitational potential energy at the top of the track.
You correctly computed the maximum elastic potential energy stored in the compressed spring.
You correctly applied the work-energy principle to determine the total energy dissipated by friction.
You correctly calculated the magnitude of the kinetic friction force.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou solved for the total distance over which friction acts (), but you set it equal to the pre-contact distance without subtracting the spring compression displacement .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking that friction acts continuously along both the approach corridor and the spring compression path when the rough surface extends under the spring.
REASONING PATH
Your ACEpath teacher’s suggested approach- Map the full friction path
If a rough floor continues under an elastic bumper, total friction work is , where is the pre-contact distance and is the spring compression.
Always sketch the complete path from the entry onto the rough surface to the point where the object momentarily stops, marking every sub-interval where friction acts.
CORRECTED PATH
ACEpath Teacher's DemonstrationExpress the total distance over which friction acts as the sum of the corridor distance and the compression distance: .
Relate this total distance to the total energy dissipated by friction: .
Solve for the pre-contact distance: .
02 The student forgets to square the compression distance x_max when calculating the elastic potential energy of the spring.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the square on the compression distance. Elastic potential energy depends quadratically on displacement: .
- Step 3Correct
Your work-energy equation correctly accounted for the friction force acting over the entire distance , but the calculation was thrown off by the incorrect spring energy value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the initial gravitational potential energy as .
You correctly calculated the friction force .
You correctly recognized that friction dissipates energy over both the corridor distance and the spring compression distance .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of in the formula for elastic potential energy, multiplying by rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the spring force formula (which is linear in ) with the elastic potential energy formula (which is quadratic in ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Energy vs. Force Dimensions
Spring force is (units of ), whereas elastic potential energy is (units of ).
Always verify that displacement is squared whenever calculating spring energy.
- Sanity-Check Energy Magnitudes
In a dissipative system without external work, final mechanical energy cannot exceed initial mechanical energy ().
If your calculated stored energy exceeds initial energy (), immediately recheck your formulas before solving for distance.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the correct elastic potential energy: .
Find the total energy that must be dissipated by friction: .
Express the work done by friction along the total rough path: .
Substitute : .
Solve for the pre-contact distance: .
03 The student forgets the factor of 1/2 in the formula for elastic potential energy, taking E_spring = k*x_max².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the factor of in the elastic potential energy formula, doubling the stored spring energy.
- Step 3Correct
This step propagated the incorrect spring energy value from step 2.
- Step 4Correct
Your physical reasoning to subtract the compression distance from the total friction path was correct, but the calculation was affected by the earlier spring energy error and sign inconsistency.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the initial gravitational potential energy of the slider.
You recognized that kinetic friction acts across both the corridor distance and the spring compression distance .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing spring force with spring potential energy: Hooke's law gives force as , whereas integrating this linear restoring force yields work and stored potential energy of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Spring Energy Formula Check
Whenever working with an elastic spring, verify that the prefactor is included, just like in kinetic energy .
- Physical Sanity Check
A distance cannot be negative
If a calculated distance comes out negative, immediately recheck whether the initial energy was larger than the final mechanical energy.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate the elastic potential energy stored at maximum compression: .
Determine the required work done by friction: .
Set up the friction work equation over total distance : .
Substitute : .
Solve for : .
Lock it in
When a block slides across a rough horizontal corridor of length and compresses a spring by on that same rough corridor, what is the total distance over which friction acts?
. Friction acts continuously from the moment the block enters the rough corridor until it momentarily comes to rest at maximum spring compression.
Similar question
A box moving at enters a rough floor with coefficient of kinetic friction and collides head-on with an uncompressed horizontal spring (). The rough surface extends under the spring. If the box slides across the rough surface before contacting the spring, calculate the maximum compression of the spring when the box momentarily stops. Use .
Answer
. Key steps: Initial kinetic energy . Friction force . Total work of friction is . Energy conservation gives . Solving the positive root yields .
A toy car is launched horizontally from an initial spring ( compressed by ) on a frictionless platform. The car immediately leaves the platform and moves up a rough ramp inclined at with . How far along the incline does the car slide before momentarily coming to rest? Use .
Answer
. Key steps: Initial stored elastic energy . Along the ramp, mechanical energy is converted into gravitational potential energy and dissipated by friction: . Factoring gives . Thus .
A runaway cart of mass descends a frictionless incline of height and enters a level emergency runout track. The level track has a friction coefficient . After sliding a distance on this rough floor, the cart contacts a bumper spring with stiffness . The rough surface extends continuously under the spring. Calculate the maximum spring compression . Use .
Answer
. Key steps: Initial energy . Friction force . Total work done by friction is . By conservation of energy, . Solving the quadratic equation for the positive root gives .