Resources

In a physics laboratory experiment, a student measures the rotational motion of an optical disk using a digital stroboscope and a photogate timer. The disk has a calibrated radius of R=12.0 cmR = 12.0\text{ cm} (0.120 m0.120\text{ m}). A strip of reflective tape of arc length Δs=1.884 cm\Delta s = 1.884\text{ cm} (0.01884 m0.01884\text{ m}) fixed to the outer rim passes through the photogate, blocking the infrared beam for a measured transit time of Δt=4.00 ms\Delta t = 4.00\text{ ms} (4.00×10−3 s4.00 \times 10^{-3}\text{ s}). Concurrently, the stroboscope flashes at a calibrated frequency of fflash=37.5 Hzf_{\text{flash}} = 37.5\text{ Hz} to freeze the rotational pattern. (a) Calculate the tangential linear speed vv of the rim from the photogate transit data. (b) Calculate the angular speed ω\omega in rad/s\text{rad/s} derived from this linear speed. (c) Calculate the theoretical angular speed ωstrobo=2πfflash\omega_{\text{strobo}} = 2\pi f_{\text{flash}} from the stroboscope setting and compute the percent error between the two independent experimental methods. Round all values to three significant figures.

Answer and steps

Final answer

(a) v=4.71 m/sv = 4.71\text{ m/s}; (b) ω=39.3 rad/s\omega = 39.3\text{ rad/s}; (c) ωstrobo=236 rad/s\omega_{\text{strobo}} = 236\text{ rad/s} for fundamental frequency, showing the disk has N=6N = 6 symmetric markers (or pattern sectors) yielding ω=2πf6=39.3 rad/s\omega = \frac{2\pi f}{6} = 39.3\text{ rad/s} with a 0.00%0.00\% discrepancy

Steps

Part (a): Tangential Linear Speed from Photogate Data

The photogate records the time interval Δt\Delta t during which the reflective tape of arc length Δs\Delta s blocks the beam. The tangential speed vv at the outer rim is the linear distance traveled divided by the transit time:

v=ΔsΔtv = \frac{\Delta s}{\Delta t}

Substitute the given values: v=0.01884 m4.00×10−3 s=4.71 m/sv = \frac{0.01884\text{ m}}{4.00 \times 10^{-3}\text{ s}} = 4.71\text{ m/s}


Part (b): Angular Speed Derived from Linear Speed

The tangential speed vv of a point moving along a circular path of radius RR is directly related to its angular speed ω\omega by the kinematic relationship:

v=ωR  ⟹  ω=vRv = \omega R \implies \omega = \frac{v}{R}

Substitute the tangential speed and the calibrated radius (R=0.120 mR = 0.120\text{ m}): ω=4.71 m/s0.120 m=39.25 rad/s≈39.3 rad/s\omega = \frac{4.71\text{ m/s}}{0.120\text{ m}} = 39.25\text{ rad/s} \approx 39.3\text{ rad/s}


Part (c): Stroboscope Angular Speed and Comparison

  1. Nominal Stroboscopic Angular Frequency: The fundamental angular frequency corresponding directly to the strobe flashing frequency fflash=37.5 Hzf_{\text{flash}} = 37.5\text{ Hz} is: ωstrobo=2πfflash=2π(37.5 s−1)≈235.6 rad/s≈236 rad/s\omega_{\text{strobo}} = 2\pi f_{\text{flash}} = 2\pi(37.5\text{ s}^{-1}) \approx 235.6\text{ rad/s} \approx 236\text{ rad/s}
  2. Interpreting the Frozen Pattern: A stroboscope creates a stationary (frozen) visual pattern whenever the flashing frequency is an integer multiple of the disk's rotational frequency: fflash=N⋅frotf_{\text{flash}} = N \cdot f_{\text{rot}} where NN represents the number of identical, symmetrically distributed sectors or markers on the disk rim.

    Comparing the stroboscope's fundamental angular frequency to the disk's measured angular speed: N=ωstroboω=235.6 rad/s39.25 rad/s=6.00N = \frac{\omega_{\text{strobo}}}{\omega} = \frac{235.6\text{ rad/s}}{39.25\text{ rad/s}} = 6.00

    This reveals that the disk possesses N=6N = 6 symmetric markers. The actual angular speed determined by the stroboscope method is: ωdisk, strobo=2πfflash6=235.6 rad/s6=39.27 rad/s≈39.3 rad/s\omega_{\text{disk, strobo}} = \frac{2\pi f_{\text{flash}}}{6} = \frac{235.6\text{ rad/s}}{6} = 39.27\text{ rad/s} \approx 39.3\text{ rad/s}

  3. Percent Discrepancy: Comparing the two independent measurements: Percent Error=∣ωdisk, strobo−ω∣ωdisk, strobo×100%=∣39.27−39.25∣39.27×100%≈0.05%≈0.00%\text{Percent Error} = \frac{|\omega_{\text{disk, strobo}} - \omega|}{\omega_{\text{disk, strobo}}} \times 100\% = \frac{|39.27 - 39.25|}{39.27} \times 100\% \approx 0.05\% \approx 0.00\% To three significant figures, the two measurement methods show complete agreement (0.00%0.00\% discrepancy).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student multiplies the linear speed by radius instead of dividing by radius when relating linear speed to angular speed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v=ΔsΔt=0.018840.00400=4.71 m/sv = \frac{\Delta s}{\Delta t} = \frac{0.01884}{0.00400} = 4.71\text{ m/s}

  2. Step 2

    ω=v⋅R  ⟹  ω=4.71⋅0.120=0.565 rad/s\omega = v \cdot R \implies \omega = 4.71 \cdot 0.120 = 0.565\text{ rad/s}

    Correct

    ω=vR=4.71 m/s0.120 m=39.3 rad/s\omega = \frac{v}{R} = \frac{4.71\text{ m/s}}{0.120\text{ m}} = 39.3\text{ rad/s}

    You multiplied linear speed by radius (v⋅Rv \cdot R) rather than dividing (v/Rv / R). Because tangential speed is v=ωRv = \omega R, solving for angular speed yields ω=vR\omega = \frac{v}{R}.

  3. Step 3

    ωstrobo=2π(37.5)=236 rad/s\omega_{\text{strobo}} = 2\pi (37.5) = 236\text{ rad/s}

  4. Step 4

    Percent error=∣0.565−236∣236×100%=99.8%\text{Percent error} = \frac{|0.565 - 236|}{236} \times 100\% = 99.8\%

    Correct

    N=235.639.25=6  ⟹  ωdisk, strobo=235.66=39.3 rad/s  ⟹  Percent Error≈0.00%N = \frac{235.6}{39.25} = 6 \implies \omega_{\text{disk, strobo}} = \frac{235.6}{6} = 39.3\text{ rad/s} \implies \text{Percent Error} \approx 0.00\%

    Your percent error calculation correctly followed your formula structure, but it was thrown off by the erroneous angular speed value from step 2 and the missing harmonic marker factor N=6N = 6.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the definition of linear velocity as arc length over transit time.

You calculated the strobe angular frequency accurately from the flash rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Inversion Error

You set ω=v⋅R\omega = v \cdot R instead of rearranging v=ωRv = \omega R into ω=vR\omega = \frac{v}{R}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the algebraic relationship between linear and angular kinematic variables, likely due to omitting unit/dimensional checks ([m/s]×[m]=m2/s≠rad/s[\text{m/s}] \times [\text{m}] = \text{m}^2/\text{s} \neq \text{rad/s}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinematic Bridging Rule
  • Linear quantities equal angular quantities multiplied by radius: s=θRs = \theta R, v=ωRv = \omega R, at=αRa_t = \alpha R.

  • Always start from v=ωRv = \omega R and isolate ω\omega by dividing both sides by RR.

Dimensional Verification
  • Angular speed has SI units of rad/s\text{rad/s} (or s−1\text{s}^{-1}).

  • Check your units: vR→m/sm=s−1=rad/s\frac{v}{R} \to \frac{\text{m/s}}{\text{m}} = \text{s}^{-1} = \text{rad/s}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the standard relation v=ωRv = \omega R and solve for angular speed: ω=vR\omega = \frac{v}{R}.

  2. Substitute v=4.71 m/sv = 4.71\text{ m/s} and R=0.120 mR = 0.120\text{ m}: ω=4.71 m/s0.120 m=39.25 rad/s≈39.3 rad/s\omega = \frac{4.71\text{ m/s}}{0.120\text{ m}} = 39.25\text{ rad/s} \approx 39.3\text{ rad/s}.

  3. Find the pattern symmetry: N=ωstroboω=235.6 rad/s39.25 rad/s=6.00N = \frac{\omega_{\text{strobo}}}{\omega} = \frac{235.6\text{ rad/s}}{39.25\text{ rad/s}} = 6.00 markers.

  4. Calculate the true stroboscopic rotational speed: ωdisk, strobo=235.6 rad/s6=39.27 rad/s≈39.3 rad/s\omega_{\text{disk, strobo}} = \frac{235.6\text{ rad/s}}{6} = 39.27\text{ rad/s} \approx 39.3\text{ rad/s}.

  5. Compute the percent error: ∣39.27−39.25∣39.27×100%≈0.00%\frac{|39.27 - 39.25|}{39.27} \times 100\% \approx 0.00\%.

Final answer

(a) v=4.71 m/sv = 4.71\text{ m/s}; (b) ω=39.3 rad/s\omega = 39.3\text{ rad/s}; (c) ωstrobo=236 rad/s\omega_{\text{strobo}} = 236\text{ rad/s}, giving N=6N = 6 and 0.00%0.00\% discrepancy

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the fundamental bridging equation in its base form: linear=angular×R\text{linear} = \text{angular} \times R.

  • Perform a quick dimensional check whenever isolating a rotational variable.

  • Practice identifying stroboscopic harmonics where fflash=N⋅frotf_{\text{flash}} = N \cdot f_{\text{rot}}.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the radius from centimeters to meters, resulting in an angular speed that is off by a factor of 100.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=ΔsΔt=0.018840.00400=4.71 m/sv = \frac{\Delta s}{\Delta t} = \frac{0.01884}{0.00400} = 4.71\text{ m/s}

  2. Step 2

    ω=vR=4.7112.0=0.393 rad/s\omega = \frac{v}{R} = \frac{4.71}{12.0} = 0.393\text{ rad/s}

    Correct

    ω=vR=4.71 m/s0.120 m=39.3 rad/s\omega = \frac{v}{R} = \frac{4.71\text{ m/s}}{0.120\text{ m}} = 39.3\text{ rad/s}

    You used R=12.0 cmR = 12.0\text{ cm} without converting it to meters (0.120 m0.120\text{ m}). Because the linear speed is in m/s\text{m/s}, the radius must also be in meters, yielding ω=39.3 rad/s\omega = 39.3\text{ rad/s}.

  3. Step 3

    ωstrobo=2π(37.5)=236 rad/s\omega_{\text{strobo}} = 2\pi(37.5) = 236\text{ rad/s}

  4. Step 4

    Percent error=∣0.393−236∣236×100%=99.8%\text{Percent error} = \frac{|0.393 - 236|}{236} \times 100\% = 99.8\%

    Correct

    N=235.6 rad/s39.25 rad/s=6  ⟹  ωdisk, strobo=235.66=39.3 rad/s  ⟹  Percent error=0.00%N = \frac{235.6\text{ rad/s}}{39.25\text{ rad/s}} = 6 \implies \omega_{\text{disk, strobo}} = \frac{235.6}{6} = 39.3\text{ rad/s} \implies \text{Percent error} = 0.00\%

    This calculation was affected by your earlier error in ω\omega. With the correct angular speed ω=39.3 rad/s\omega = 39.3\text{ rad/s}, the strobe's fundamental frequency is an exact integer harmonic (N=6N = 6 symmetric markers on the disk), resulting in a 0.00%0.00\% discrepancy.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the definition of linear speed as arc length divided by transit time.

You identified the correct kinematic relationship ω=vR\omega = \frac{v}{R} connecting linear and angular speed.

You correctly computed the angular frequency from the stroboscopic flashing rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You did not convert the radius from centimeters to standard SI base units (meters) before substituting it into ω=vR\omega = \frac{v}{R}, causing an order-of-magnitude error of 10210^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Unit Consistency
  • In kinematic formulas connecting linear and rotational quantities (v=ωRv = \omega R, a=αRa = \alpha R), all length quantities must share the same linear unit (typically meters).

  • Always verify that linear quantities are converted to meters before dividing or multiplying with angular quantities.

Harmonic Pattern Recognition
  • When a stroboscope freezes a rotating object with NN symmetric features, the flashing frequency relates to the rotation frequency by fflash=Nfrotf_{\text{flash}} = N f_{\text{rot}}, so ωrot=ωstroboN\omega_{\text{rot}} = \frac{\omega_{\text{strobo}}}{N}.

  • Divide the nominal stroboscopic frequency by the integer pattern multiplier NN to obtain the true angular speed before computing percent error.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ω=vR=4.71 m/s0.120 m=39.25 rad/s≈39.3 rad/s\omega = \frac{v}{R} = \frac{4.71\text{ m/s}}{0.120\text{ m}} = 39.25\text{ rad/s} \approx 39.3\text{ rad/s}

  2. N=ωstroboω=235.6 rad/s39.25 rad/s=6.00N = \frac{\omega_{\text{strobo}}}{\omega} = \frac{235.6\text{ rad/s}}{39.25\text{ rad/s}} = 6.00

  3. ωdisk, strobo=235.6 rad/s6=39.27 rad/s≈39.3 rad/s\omega_{\text{disk, strobo}} = \frac{235.6\text{ rad/s}}{6} = 39.27\text{ rad/s} \approx 39.3\text{ rad/s}

  4. Percent error=∣39.27−39.25∣39.27×100%≈0.00%\text{Percent error} = \frac{|39.27 - 39.25|}{39.27} \times 100\% \approx 0.00\%

Final answer

(a) v=4.71 m/sv = 4.71\text{ m/s}; (b) ω=39.3 rad/s\omega = 39.3\text{ rad/s}; (c) ωstrobo=236 rad/s\omega_{\text{strobo}} = 236\text{ rad/s}, showing N=6N = 6 symmetric sectors yielding ω=39.3 rad/s\omega = 39.3\text{ rad/s} with a 0.00%0.00\% discrepancy.

NEXT STEPS
Final Takeaways from Your Teacher
  • Recompute Part (b) using R=0.120 mR = 0.120\text{ m} to get the proper angular speed in rad/s\text{rad/s}.

  • Observe that the strobe frequency 236 rad/s236\text{ rad/s} is an exact multiple (6×6\times) of your corrected rotational speed.

  • Practice verifying dimensional consistency on all inputs before executing numerical calculations.

OverviewACEpath Teacher's Diagnosis

03 The student omits the factor of 2π when calculating the stroboscopic angular speed, conflating cyclical frequency in hertz with angular frequency in radians per second.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=ΔsΔt=0.018840.00400=4.71 m/sv = \frac{\Delta s}{\Delta t} = \frac{0.01884}{0.00400} = 4.71\text{ m/s}

  2. Step 2

    ω=vR=4.710.120=39.3 rad/s\omega = \frac{v}{R} = \frac{4.71}{0.120} = 39.3\text{ rad/s}

  3. Step 3

    ωstrobo=fflash=37.5 rad/s\omega_{\text{strobo}} = f_{\text{flash}} = 37.5\text{ rad/s}

    Correct

    ωstrobo=2πfflash=2π(37.5 s−1)≈236 rad/s\omega_{\text{strobo}} = 2\pi f_{\text{flash}} = 2\pi(37.5\text{ s}^{-1}) \approx 236\text{ rad/s}

    You set angular speed ω\omega equal to cyclical frequency ff. To convert full cycles per second (Hz\text{Hz}) into radians per second (rad/s\text{rad/s}), you must multiply by 2π2\pi radians per cycle.

  4. Step 4

    Percent error\text{Percent error} = ∣39.25−37.537.5∣\left|\frac{39.25 - 37.5}{37.5}\right| ×\times 100% = 4.67%

    Correct

    ωstroboω\frac{\omega_{\text{strobo}}}{\omega} = 235.639.25\frac{235.6}{39.25} = 6.00   ⟹  \implies ω\omega{disk, strobo\text{disk, strobo}} = 235.66\frac{235.6}{6} = 39.27 rad/s\text{ rad/s}   ⟹  \implies Percent error\text{Percent error} ≈\approx 0.05% ≈\approx 0.00%

    Your percent error calculation used the incorrect stroboscopic angular speed from the previous step and omitted the pattern symmetry factor N=6N = 6.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used linear kinematics to find tangential speed from distance and time.

You accurately applied the relationship v=ωRv = \omega R to convert tangential speed into angular speed.

You set up the percent error formula correctly using your computed values.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating Frequency and Angular Speed

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated cyclical frequency ff (measured in hertz or cycles/second) as identical to angular speed ω\omega (measured in radians/second), omitting the required factor of 2π rad/rev2\pi\text{ rad/rev}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Cyclical Frequency vs. Angular Speed
  • One complete rotation equals 2π radians2\pi\text{ radians}, so ω=2πf\omega = 2\pi f.

  • Always verify units: if frequency is in Hz\text{Hz} (cycles/s), multiply by 2π2\pi to obtain angular speed in rad/s\text{rad/s}.

Stroboscopic Symmetry Factor
  • When a strobe pattern appears frozen at a multiple frequency, fflash=N⋅frotf_{\text{flash}} = N \cdot f_{\text{rot}}, where NN is the number of symmetric pattern elements.

  • Check whether ωstrobo\omega_{\text{strobo}} is an integer multiple of the disk's physical rotation rate before computing discrepancy.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the nominal stroboscopic angular frequency: ωstrobo=2πfflash=2π(37.5 s−1)=235.6 rad/s≈236 rad/s\omega_{\text{strobo}} = 2\pi f_{\text{flash}} = 2\pi(37.5\text{ s}^{-1}) = 235.6\text{ rad/s} \approx 236\text{ rad/s}.

  2. Recognize the stationary pattern harmonic ratio: N=235.6 rad/s39.25 rad/s=6.00N = \frac{235.6\text{ rad/s}}{39.25\text{ rad/s}} = 6.00, indicating N=6N = 6 symmetric markers.

  3. Compute the true disk angular speed from the strobe data: ωdisk, strobo=235.6 rad/s6=39.27 rad/s≈39.3 rad/s\omega_{\text{disk, strobo}} = \frac{235.6\text{ rad/s}}{6} = 39.27\text{ rad/s} \approx 39.3\text{ rad/s}.

  4. Compute the percent discrepancy: Percent Error=∣39.27−39.25∣39.27×100%≈0.05%≈0.00%\text{Percent Error} = \frac{|39.27 - 39.25|}{39.27} \times 100\% \approx 0.05\% \approx 0.00\%.

Final answer

(a) v=4.71 m/sv = 4.71\text{ m/s}; (b) ω=39.3 rad/s\omega = 39.3\text{ rad/s}; (c) ωstrobo=236 rad/s\omega_{\text{strobo}} = 236\text{ rad/s}, showing N=6N = 6 symmetric markers yielding ω=39.3 rad/s\omega = 39.3\text{ rad/s} with a 0.00%0.00\% discrepancy.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting between rotational frequency ff (Hz\text{Hz} or rpm\text{rpm}) and angular velocity ω\omega (rad/s\text{rad/s}) by checking the units on both sides of every equation.

  • Review stroboscopic freezing conditions where multiple symmetrical sectors cause visual aliasing at integer harmonics.

Lock it in

Similar question

01

A compact disc with radius R=6.0 cmR = 6.0\text{ cm} spins such that a point on its outer circumference moves at a linear speed of 1.5 m/s1.5\text{ m/s}. Find the angular speed ω\omega in rad/s\text{rad/s}.

Answer

ω=25 rad/s\omega = 25\text{ rad/s}. Key step: Convert radius to meters (R=0.060 mR = 0.060\text{ m}), then divide linear speed by radius: ω=vR=1.5 m/s0.060 m=25 rad/s\omega = \frac{v}{R} = \frac{1.5\text{ m/s}}{0.060\text{ m}} = 25\text{ rad/s}.

02

An ultra-centrifuge rotor spins at an angular speed of ω=4.0×103 rad/s\omega = 4.0 \times 10^3\text{ rad/s}. A sample tube is positioned at a distance of r=8.5 cmr = 8.5\text{ cm} from the central axis of rotation. What is the tangential linear speed vv of the sample, and what would the angular speed be if the tangential speed were 255 m/s255\text{ m/s} at that same radius?

Answer

v=340 m/sv = 340\text{ m/s} and ω=3.0×103 rad/s\omega = 3.0 \times 10^3\text{ rad/s}. Key steps: First, v=ωr=(4000 rad/s)(0.085 m)=340 m/sv = \omega r = (4000\text{ rad/s})(0.085\text{ m}) = 340\text{ m/s}. Second, isolating ω\omega yields ω=vr=255 m/s0.085 m=3000 rad/s\omega = \frac{v}{r} = \frac{255\text{ m/s}}{0.085\text{ m}} = 3000\text{ rad/s}.

03

A turntable of radius R=15.0 cmR = 15.0\text{ cm} has two concentric tracks: track A at radius rA=5.0 cmr_A = 5.0\text{ cm} and track B at outer rim rB=15.0 cmr_B = 15.0\text{ cm}. If an object on track A moves with a linear speed of vA=0.40 m/sv_A = 0.40\text{ m/s}, calculate the common angular speed ω\omega of the turntable and the tangential linear speed vBv_B at track B.

Answer

ω=8.0 rad/s\omega = 8.0\text{ rad/s} and vB=1.2 m/sv_B = 1.2\text{ m/s}. Key steps: All points on a rigid body share the same angular velocity: ω=vArA=0.40 m/s0.050 m=8.0 rad/s\omega = \frac{v_A}{r_A} = \frac{0.40\text{ m/s}}{0.050\text{ m}} = 8.0\text{ rad/s}. Then, linear speed at track B is vB=ωrB=(8.0 rad/s)(0.150 m)=1.2 m/sv_B = \omega r_B = (8.0\text{ rad/s})(0.150\text{ m}) = 1.2\text{ m/s}.

Loading workspace…