Resources

An engineering calibration sled has a total mass of m=8.50×104 gm = 8.50\times 10^4\text{ g}. It is pulled along a test track by a tow cable exerting a tension of T=3.60×107 dynesT = 3.60\times 10^7\text{ dynes} at an angle of θ=35.0∘\theta = 35.0^\circ above the horizontal. The contact surface has a coefficient of kinetic friction μk=0.180\mu_k = 0.180, and the local gravitational acceleration is g=980 cm/s2g = 980\text{ cm/s}^2. (a) Convert all physical quantities into standard SI units (kgkg, NN, and m/s2\text{m/s}^2). (b) Set up the free-body diagram force balance equations and calculate the normal force FNF_N in newtons. (c) Determine the resulting horizontal acceleration axa_x of the sled in m/s2\text{m/s}^2.

Answer and steps

Final answer

(a) m=85.0 kgm = 85.0\text{ kg}, T=360 NT = 360\text{ N}, g=9.80 m/s2g = 9.80\text{ m/s}^2; (b) FN=mg−Tsin⁡θ=(85.0)(9.80)−360sin⁡(35.0∘)=627 NF_N = mg - T\sin\theta = (85.0)(9.80) - 360\sin(35.0^\circ) = 627\text{ N}; (c) ax=Tcos⁡θ−μkFNm=295−11385.0=2.14 m/s2a_x = \frac{T\cos\theta - \mu_k F_N}{m} = \frac{295 - 113}{85.0} = 2.14\text{ m/s}^2.

Steps

Part (a): Convert Quantities into Standard SI Units

To apply standard formulas in mechanics, all given values must be expressed in SI base or derived units:

  1. Mass (mm): Since 1 kg=103 g1\text{ kg} = 10^3\text{ g}, m=8.50×104 g103 g/kg=85.0 kgm = \frac{8.50 \times 10^4\text{ g}}{10^3\text{ g/kg}} = 85.0\text{ kg}
  2. Tension (TT): By definition, 1 dyne=1 g⋅cm/s2=10−5 N1\text{ dyne} = 1\text{ g}\cdot\text{cm/s}^2 = 10^{-5}\text{ N}, T=(3.60×107 dynes)×(10−5 N/dyne)=360 NT = (3.60 \times 10^7\text{ dynes}) \times (10^{-5}\text{ N/dyne}) = 360\text{ N}
  3. Acceleration due to gravity (gg): Since 1 m=100 cm1\text{ m} = 100\text{ cm}, g=980 cm/s2100 cm/m=9.80 m/s2g = \frac{980\text{ cm/s}^2}{100\text{ cm/m}} = 9.80\text{ m/s}^2

Part (b): Free-Body Diagram and Normal Force

Choose a coordinate system where the positive xx-axis points in the direction of motion (horizontally to the right) and the positive yy-axis points vertically upward.

The forces acting on the sled are:

  • Gravity pointing downward: W=mgW = mg
  • Normal force from the track pointing upward: FNF_N
  • Pulling tension at an angle θ\theta above the horizontal: Tx=Tcos⁡θ,Ty=Tsin⁡θT_x = T\cos\theta, \quad T_y = T\sin\theta
  • Kinetic friction opposing the motion horizontally: fk=μkFNf_k = \mu_k F_N

Because there is no vertical motion, the vertical acceleration is zero (ay=0a_y = 0). Applying Newton's second law along the yy-axis: ∑Fy=FN+Tsin⁡θ−mg=0\sum F_y = F_N + T\sin\theta - mg = 0

Solving for the normal force FNF_N: FN=mg−Tsin⁡θF_N = mg - T\sin\theta

Substitute the numerical values: FN=(85.0 kg)(9.80 m/s2)−(360 N)sin⁡(35.0∘)F_N = (85.0\text{ kg})(9.80\text{ m/s}^2) - (360\text{ N})\sin(35.0^\circ) FN=833 N−206.5 N≈627 NF_N = 833\text{ N} - 206.5\text{ N} \approx 627\text{ N}

Common Pitfall: Do not assume FN=mgF_N = mg. When an applied tension pulls partly upward (Tsin⁡θ>0T\sin\theta > 0), it relieves some of the contact force, making the normal force smaller than the object's weight.


Part (c): Determine the Horizontal Acceleration

Apply Newton's second law along the horizontal direction: ∑Fx=Tcos⁡θ−fk=max\sum F_x = T\cos\theta - f_k = m a_x

Using fk=μkFNf_k = \mu_k F_N: ax=Tcos⁡θ−μkFNma_x = \frac{T\cos\theta - \mu_k F_N}{m}

Substitute the calculated values: Tcos⁡(35.0∘)=360cos⁡(35.0∘)≈295 NT\cos(35.0^\circ) = 360\cos(35.0^\circ) \approx 295\text{ N} fk=0.180×626.5 N≈113 Nf_k = 0.180 \times 626.5\text{ N} \approx 113\text{ N}

Calculate the acceleration: ax=295 N−113 N85.0 kg=182 N85.0 kg≈2.14 m/s2a_x = \frac{295\text{ N} - 113\text{ N}}{85.0\text{ kg}} = \frac{182\text{ N}}{85.0\text{ kg}} \approx 2.14\text{ m/s}^2

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that the upward component of tension reduces the normal force and assumes F_N = m g, which overestimates friction and underestimates acceleration.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m=85.0 kg  ⟹  T=360 N  ⟹  g=9.80 m/s2m = 85.0\text{ kg} \implies T = 360\text{ N} \implies g = 9.80\text{ m/s}^2

  2. Step 2

    FN=mg=85.0×9.80=833 NF_N = mg = 85.0 \times 9.80 = 833\text{ N}

    Correct

    ∑Fy=FN+Tsin⁡35.0∘−mg=0  ⟹  FN=mg−Tsin⁡35.0∘≈627 N\sum F_y = F_N + T\sin 35.0^\circ - mg = 0 \implies F_N = mg - T\sin 35.0^\circ \approx 627\text{ N}

    You equated the normal force directly to mgmg. Because the tow cable pulls at an angle above the horizontal, its upward component Tsin⁡θT\sin\theta helps support the sled's weight and reduces the required normal force.

  3. Step 3

    fk=μkFN=0.180×833=149.94 N  ⟹  Tcos⁡35.0∘−fk=max  ⟹  294.89−149.94=85.0ax  ⟹  ax≈1.71 m/s2f_k = \mu_k F_N = 0.180 \times 833 = 149.94\text{ N} \implies T\cos 35.0^\circ - f_k = ma_x \implies 294.89 - 149.94 = 85.0 a_x \implies a_x \approx 1.71\text{ m/s}^2

    Correct

    ax=Tcos⁡35.0∘−μkFNm=294.89−0.180(626.5)85.0≈2.14 m/s2a_x = \frac{T\cos 35.0^\circ - \mu_k F_N}{m} = \frac{294.89 - 0.180(626.5)}{85.0} \approx 2.14\text{ m/s}^2

    You set up Newton's second law along the horizontal axis correctly, but the resulting acceleration was lower than expected due to the overestimated normal force propagated from part (b).

WHAT YOU DID WELL
Compliments from Your Teacher

You performed all SI unit conversions accurately.

You identified the correct horizontal components for pulling tension and kinetic friction.

You applied Newton's second law algebraically to solve for acceleration.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglected force component in vertical equilibrium

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the normal force as an automatic default of FN=mgF_N = mg rather than determining it dynamically from the vertical force balance ∑Fy=0\sum F_y = 0.

REASONING PATH
Your ACEpath teacher’s suggested approach
Vertical Equilibrium Equation
  • For an object resting on a horizontal surface without vertical acceleration, ∑Fy=FN+Ty−mg=0\sum F_y = F_N + T_y - mg = 0.

  • Always draw a free-body diagram and sum all vertical forces before writing an expression for the normal force.

Effect of Angled Pull on Friction
  • Kinetic friction depends directly on the normal force (fk=μkFNf_k = \mu_k F_N), which changes when applied forces have vertical components.

  • Calculate FNF_N from the complete vertical balance equation before computing fkf_k.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the vertical force balance: FN+Tsin⁡(35.0∘)−mg=0F_N + T\sin(35.0^\circ) - mg = 0.

  2. Solve for the normal force: FN=mg−Tsin⁡(35.0∘)=(85.0)(9.80)−360sin⁡(35.0∘)=833−206.5=626.5 N≈627 NF_N = mg - T\sin(35.0^\circ) = (85.0)(9.80) - 360\sin(35.0^\circ) = 833 - 206.5 = 626.5\text{ N} \approx 627\text{ N}.

  3. Recalculate kinetic friction: fk=μkFN=0.180×626.5 N≈112.8 Nf_k = \mu_k F_N = 0.180 \times 626.5\text{ N} \approx 112.8\text{ N}.

  4. Apply Newton's second law horizontally: ax=Tcos⁡(35.0∘)−fkm=294.9−112.885.0≈2.14 m/s2a_x = \frac{T\cos(35.0^\circ) - f_k}{m} = \frac{294.9 - 112.8}{85.0} \approx 2.14\text{ m/s}^2.

Final answer

(a) m=85.0 kg,  T=360 N,  g=9.80 m/s2m = 85.0\text{ kg}, \; T = 360\text{ N}, \; g = 9.80\text{ m/s}^2; (b) FN≈627 NF_N \approx 627\text{ N}; (c) ax≈2.14 m/s2a_x \approx 2.14\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice sketching free-body diagrams that explicitly split every angled vector into orthogonal components before writing algebraic equations.

  • Solve problems where applied forces push downward at an angle to see how FNF_N becomes greater than mgmg.

OverviewACEpath Teacher's Diagnosis

02 The student adds the vertical component of tension instead of subtracting it when solving for the normal force, obtaining F_N = m g + T sin θ.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m=85.0 kgm = 85.0\text{ kg}, T=360 NT = 360\text{ N}, g=9.80 m/s2g = 9.80\text{ m/s}^2

  2. Step 2

    FN=mg+Tsin⁡35.0∘  ⟹  FN=85.0×9.80+360sin⁡35.0∘  ⟹  FN=833+206.49=1039.49 N≈1040 NF_N = mg + T\sin 35.0^\circ \implies F_N = 85.0 \times 9.80 + 360\sin 35.0^\circ \implies F_N = 833 + 206.49 = 1039.49\text{ N} \approx 1040\text{ N}

    Correct

    FN+Tsin⁡35.0∘−mg=0  ⟹  FN=mg−Tsin⁡35.0∘=833−206.5=627 NF_N + T\sin 35.0^\circ - mg = 0 \implies F_N = mg - T\sin 35.0^\circ = 833 - 206.5 = 627\text{ N}

    Because the cable pulls upward at an angle, its vertical component Tsin⁡θT\sin\theta acts upward alongside the normal force FNF_N. The equilibrium equation along the vertical axis is FN+Tsin⁡θ−mg=0F_N + T\sin\theta - mg = 0, which yields FN=mg−Tsin⁡θF_N = mg - T\sin\theta, not mg+Tsin⁡θmg + T\sin\theta.

  3. Step 3

    fk=0.180×1039.49=187.11 N  ⟹  Tcos⁡35.0∘−fk=max  ⟹  294.89−187.11=85.0ax  ⟹  ax=107.7885.0≈1.27 m/s2f_k = 0.180 \times 1039.49 = 187.11\text{ N} \implies T\cos 35.0^\circ - f_k = ma_x \implies 294.89 - 187.11 = 85.0a_x \implies a_x = \frac{107.78}{85.0} \approx 1.27\text{ m/s}^2

    Correct

    fk=0.180×626.5=113 N  ⟹  ax=295−11385.0≈2.14 m/s2f_k = 0.180 \times 626.5 = 113\text{ N} \implies a_x = \frac{295 - 113}{85.0} \approx 2.14\text{ m/s}^2

    Your application of Newton's second law along the horizontal direction was mathematically correct based on your computed normal force, but the resulting numerical value was affected by the sign error in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted all given quantities into standard SI units without error.

You correctly resolved the tension vector into orthogonal components using sine and cosine.

You correctly applied Newton's second law along the horizontal direction with kinetic friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal Force Sign Inversion

You added the upward vertical component of tension to the gravitational force when isolating FNF_N, rather than subtracting it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating FNF_N as a formula that automatically combines magnitudes without first writing out the signed equilibrium equation ∑Fy=FN+Ty−W=0\sum F_y = F_N + T_y - W = 0. When pulling upward, tension partially lifts the object and relieves the contact surface.

REASONING PATH
Your ACEpath teacher’s suggested approach
Write the Full Sum of Forces
  • Along any static axis, write ∑F=0\sum F = 0 with explicit directional signs before isolating any single force.

  • Assign upward forces as positive and downward as negative: FN+Tsin⁡θ−mg=0F_N + T\sin\theta - mg = 0.

Physical Reality Check for Normal Force
  • An upward pull always reduces the surface compression, meaning FN<mgF_N < mg. A downward push increases it, meaning FN>mgF_N > mg.

  • Check whether your result for FNF_N is smaller than mg=833 Nmg = 833\text{ N} when tension pulls upward.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the correct vertical equilibrium equation: FN=mg−Tsin⁡35.0∘F_N = mg - T\sin 35.0^\circ.

  2. Evaluate the normal force: FN=(85.0)(9.80)−360sin⁡(35.0∘)=833 N−206.5 N=626.5 N≈627 NF_N = (85.0)(9.80) - 360\sin(35.0^\circ) = 833\text{ N} - 206.5\text{ N} = 626.5\text{ N} \approx 627\text{ N}.

  3. Recompute the friction force: fk=μkFN=0.180×626.5 N≈112.8 Nf_k = \mu_k F_N = 0.180 \times 626.5\text{ N} \approx 112.8\text{ N}.

  4. Calculate horizontal acceleration: ax=Tcos⁡35.0∘−fkm=294.9 N−112.8 N85.0 kg=182.1 N85.0 kg≈2.14 m/s2a_x = \frac{T\cos 35.0^\circ - f_k}{m} = \frac{294.9\text{ N} - 112.8\text{ N}}{85.0\text{ kg}} = \frac{182.1\text{ N}}{85.0\text{ kg}} \approx 2.14\text{ m/s}^2.

Final answer

FN≈627 NF_N \approx 627\text{ N}, ax≈2.14 m/s2a_x \approx 2.14\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Always sketch a free-body diagram showing arrow directions before writing algebraic formulas for contact forces.

  • Practice solving ∑Fy=0\sum F_y = 0 explicitly by stating all upward forces equal all downward forces: FN+Ty=mgF_N + T_y = mg.

OverviewACEpath Teacher's Diagnosis

03 The student swaps the trigonometric components, incorrectly using cos(θ) for the vertical balance and sin(θ) for the horizontal motion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m=85.0 kgm = 85.0\text{ kg}, T=360 NT = 360\text{ N}, g=9.80 m/s2g = 9.80\text{ m/s}^2

  2. Step 2

    FN=mg−Tcos⁡35.0∘  ⟹  FN=85.0×9.80−360cos⁡35.0∘≈538 NF_N = mg - T\cos 35.0^\circ \implies F_N = 85.0 \times 9.80 - 360\cos 35.0^\circ \approx 538\text{ N}

    Correct

    FN=mg−Tsin⁡35.0∘=(85.0)(9.80)−360sin⁡(35.0∘)≈627 NF_N = mg - T\sin 35.0^\circ = (85.0)(9.80) - 360\sin(35.0^\circ) \approx 627\text{ N}

    Because the angle θ=35.0∘\theta = 35.0^\circ is measured above the horizontal, the vertical component opposite to the angle is Tsin⁡θT\sin\theta, not Tcos⁡θT\cos\theta.

  3. Step 3

    fk=0.180×538.11=96.86 N  ⟹  Tsin⁡35.0∘−fk=max  ⟹  ax≈1.29 m/s2f_k = 0.180 \times 538.11 = 96.86\text{ N} \implies T\sin 35.0^\circ - f_k = m a_x \implies a_x \approx 1.29\text{ m/s}^2

    Correct

    ax=Tcos⁡35.0∘−μkFNm=360cos⁡(35.0∘)−0.180(626.5)85.0≈2.14 m/s2a_x = \frac{T\cos 35.0^\circ - \mu_k F_N}{m} = \frac{360\cos(35.0^\circ) - 0.180(626.5)}{85.0} \approx 2.14\text{ m/s}^2

    The horizontal component driving the motion is adjacent to the horizontal angle, so it requires Tcos⁡θT\cos\theta rather than Tsin⁡θT\sin\theta. This calculation was also affected by your previous normal force value.

WHAT YOU DID WELL
Compliments from Your Teacher

You performed all unit conversions into standard SI units correctly.

You recognized that an upward-angled tension reduces the normal force exerted by the surface.

You correctly related the kinetic friction force to the normal force via fk=μkFNf_k = \mu_k F_N.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Swap

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the cosine function with the vertical axis and sine with the horizontal axis, reversing the standard right-triangle definitions where the side adjacent to the horizontal angle is horizontal (Tcos⁡θT\cos\theta) and the opposite side is vertical (Tsin⁡θT\sin\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Resolving Vector Components
  • When an angle θ\theta is given relative to the horizontal: the horizontal component is adjacent (A=Hcos⁡θA = H\cos\theta) and the vertical component is opposite (O=Hsin⁡θO = H\sin\theta).

  • Always sketch a right triangle with the force vector as the hypotenuse before writing force balance equations, explicitly labeling adjacent and opposite sides.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the vertical equilibrium equation: ∑Fy=FN+Tsin⁡(35.0∘)−mg=0\sum F_y = F_N + T\sin(35.0^\circ) - mg = 0.

  2. Solve for the normal force: FN=(85.0 kg)(9.80 m/s2)−(360 N)sin⁡(35.0∘)≈626.53 N≈627 NF_N = (85.0\text{ kg})(9.80\text{ m/s}^2) - (360\text{ N})\sin(35.0^\circ) \approx 626.53\text{ N} \approx 627\text{ N}.

  3. Calculate the friction force: fk=μkFN=0.180×626.53 N≈112.78 Nf_k = \mu_k F_N = 0.180 \times 626.53\text{ N} \approx 112.78\text{ N}.

  4. Apply Newton's second law horizontally: ∑Fx=Tcos⁡(35.0∘)−fk=max\sum F_x = T\cos(35.0^\circ) - f_k = m a_x.

  5. Compute the acceleration: ax=360cos⁡(35.0∘)−112.7885.0=294.89−112.7885.0≈2.14 m/s2a_x = \frac{360\cos(35.0^\circ) - 112.78}{85.0} = \frac{294.89 - 112.78}{85.0} \approx 2.14\text{ m/s}^2.

Final answer

(a) m=85.0 kgm = 85.0\text{ kg}, T=360 NT = 360\text{ N}, g=9.80 m/s2g = 9.80\text{ m/s}^2; (b) FN≈627 NF_N \approx 627\text{ N}; (c) ax≈2.14 m/s2a_x \approx 2.14\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a small right triangle for every angled force vector to verify whether sine or cosine corresponds to the opposite side.

  • Remember that cos⁡θ\cos\theta always pairs with the leg touching (adjacent to) the specified angle θ\theta.

Lock it in

Similar question

01

A 40.0 kg40.0\text{ kg} crate is pulled across a rough horizontal floor by a force of 150 N150\text{ N} directed at 30.0∘30.0^\circ above the horizontal. If g=9.80 m/s2g = 9.80\text{ m/s}^2, find the normal force exerted by the floor on the crate.

Answer

FN=mg−Fsin⁡θ=(40.0)(9.80)−150sin⁡(30.0∘)=392−75.0=317 NF_N = mg - F\sin\theta = (40.0)(9.80) - 150\sin(30.0^\circ) = 392 - 75.0 = 317\text{ N}.

02

A 25.0 kg25.0\text{ kg} lawnmower is pushed across a level lawn with a force of 120 N120\text{ N} directed along the handle at an angle of 40.0∘40.0^\circ below the horizontal. Assuming g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the normal force.

Answer

Because the push is downward, the vertical component adds to gravity: FN=mg+Fsin⁡θ=(25.0)(9.80)+120sin⁡(40.0∘)=245+77.1=322 NF_N = mg + F\sin\theta = (25.0)(9.80) + 120\sin(40.0^\circ) = 245 + 77.1 = 322\text{ N}.

03

A 10.0 kg10.0\text{ kg} block rests on a horizontal surface with coefficient of kinetic friction μk=0.250\mu_k = 0.250. A pulling force P=50.0 NP = 50.0\text{ N} acts at an angle θ=37.0∘\theta = 37.0^\circ above the horizontal (g=9.80 m/s2g = 9.80\text{ m/s}^2). Determine the block's horizontal acceleration.

Answer

First find the normal force: FN=mg−Psin⁡(37.0∘)=(10.0)(9.80)−50.0(0.6018)=98.0−30.1=67.9 NF_N = mg - P\sin(37.0^\circ) = (10.0)(9.80) - 50.0(0.6018) = 98.0 - 30.1 = 67.9\text{ N}. Next calculate friction: fk=μkFN=0.250×67.9=17.0 Nf_k = \mu_k F_N = 0.250 \times 67.9 = 17.0\text{ N}. Finally compute acceleration: ax=Pcos⁡(37.0∘)−fkm=50.0(0.7986)−17.010.0=39.9−17.010.0=2.29 m/s2a_x = \frac{P\cos(37.0^\circ) - f_k}{m} = \frac{50.0(0.7986) - 17.0}{10.0} = \frac{39.9 - 17.0}{10.0} = 2.29\text{ m/s}^2.

Loading workspace…