Resources

A student measures the current through an ohmic resistor RR connected to an ideal variable DC voltage source VV, recording a baseline current I0I_0. The student hypothesizes that if the applied voltage is increased by a factor of 3.003.00 while simultaneously tripling the resistance by switching to three identical resistors in series (3.00R3.00 R), the current will increase ninefold due to the increased voltage pushing through the system. Using Ohm's law, determine the true numerical ratio of the new current to the initial current, InewI0\frac{I_{\text{new}}}{I_0}, and state whether the current increases, decreases, or remains unchanged.

Answer and steps

Final answer

1.001.00 (the current remains unchanged)

Steps

01

State the Governing Relationship (Ohm's Law)

For an ohmic resistor, the relationship between current (II), electric potential difference (VV), and resistance (RR) is given by Ohm's law:

I=VRI = \frac{V}{R}

02

Express the Baseline Current

In the initial circuit setup:

  • Applied voltage =V= V
  • Total resistance =R= R

Thus, the initial baseline current is:

I0=VRI_0 = \frac{V}{R}

03

Determine the New Current After Modifications

The problem specifies two simultaneous changes:

  • The voltage increases by a factor of 3.003.00: Vnew=3.00VV_{\text{new}} = 3.00 V
  • The resistance triples by connecting three identical resistors in series: Rnew=R+R+R=3.00RR_{\text{new}} = R + R + R = 3.00 R

Substitute these values into Ohm's law to find the new current, InewI_{\text{new}}:

Inew=VnewRnew=3.00V3.00RI_{\text{new}} = \frac{V_{\text{new}}}{R_{\text{new}}} = \frac{3.00 V}{3.00 R}

Canceling the common factor of 3.003.00 from the numerator and the denominator yields:

Inew=VR=I0I_{\text{new}} = \frac{V}{R} = I_0

04

Calculate the Current Ratio and Identify Common Pitfalls

Find the ratio of the new current to the baseline current:

InewI0=I0I0=1.00\frac{I_{\text{new}}}{I_0} = \frac{I_0}{I_0} = 1.00

Common Pitfall: The student's hypothesis mistakenly assumed that multiplying both voltage and resistance by 33 results in a ninefold increase (3×3=93 \times 3 = 9). Current is directly proportional to voltage (I∝VI \propto V), but inversely proportional to resistance (I∝1RI \propto \frac{1}{R}). When both parameters scale by the same factor, the two effects exactly balance, leaving the current unchanged.

Therefore, the ratio is 1.001.00, and the current remains unchanged.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student misremembers Ohm's law as I = V · R, leading to multiplying the voltage factor by the resistance factor and concluding the current increases by a factor of 9.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=V⋅R  ⟹  I0=V⋅RI = V \cdot R \implies I_0 = V \cdot R

    Correct

    I=VR  ⟹  I0=VRI = \frac{V}{R} \implies I_0 = \frac{V}{R}

    Ohm's law states that V=I⋅RV = I \cdot R, which rearranges to I=VRI = \frac{V}{R}. Writing I=V⋅RI = V \cdot R treats resistance as an amplifier of current rather than an opposition to it.

  2. Step 2

    Inew=(3.00V)⋅(3.00R)=9.00V⋅RI_{\text{new}} = (3.00 V) \cdot (3.00 R) = 9.00 V \cdot R

    Correct

    Inew=3.00V3.00R=1.00VRI_{\text{new}} = \frac{3.00 V}{3.00 R} = 1.00 \frac{V}{R}

    You accurately substituted the 3.003.00 scaling factor for both voltage and resistance, but because of the formula error in Step 1, you multiplied the factors instead of dividing them.

  3. Step 3

    InewI0=9.00  ⟹  The current increases.\frac{I_{\text{new}}}{I_0} = 9.00 \implies \text{The current increases.}

    Correct

    InewI0=1.00  ⟹  The current remains unchanged.\frac{I_{\text{new}}}{I_0} = 1.00 \implies \text{The current remains unchanged.}

    Your ratio calculation followed logically from your previous expression, but the correct ratio is 1.001.00, meaning the current stays the same.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that both the applied voltage and the total resistance scale by a factor of 3.003.00.

You clearly stated your baseline and modified expressions to find the ratio InewI0\frac{I_{\text{new}}}{I_0}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Ohm's Law Inversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You misremembered Ohm's law as a product (I=V⋅RI = V \cdot R) rather than a quotient (I=VRI = \frac{V}{R}). Consequently, you treated resistance as directly proportional to current instead of inversely proportional to it.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate Current in Ohm's Law
  • V=I⋅R  ⟺  I=VRV = I \cdot R \iff I = \frac{V}{R}

  • Whenever solving for current, divide the potential difference by the resistance to reflect that resistance opposes charge flow.

Proportionality Sanity Check
  • I∝VI \propto V and I∝1RI \propto \frac{1}{R}

  • Before multiplying scaling factors, verify whether each physical change promotes or hinders current flow.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Ohm's law solved for current: I0=VRI_0 = \frac{V}{R}.

  2. Substitute the scaled values: Inew=VnewRnew=3.00V3.00RI_{\text{new}} = \frac{V_{\text{new}}}{R_{\text{new}}} = \frac{3.00 V}{3.00 R}.

  3. Cancel the common factor of 3.003.00: Inew=VR=I0I_{\text{new}} = \frac{V}{R} = I_0.

  4. Compute the ratio: InewI0=I0I0=1.00\frac{I_{\text{new}}}{I_0} = \frac{I_0}{I_0} = 1.00.

Final answer

1.001.00 (the current remains unchanged)

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the triangle mnemonic or algebraic rearrangements for V=I⋅RV = I \cdot R to ensure you isolate the desired variable correctly.

  • Practice qualitative scaling questions by checking whether changes in circuit parameters reinforce or counteract one another.

OverviewACEpath Teacher's Diagnosis

02 A student inverts Ohm's law as I = R / V, placing resistance in the numerator and voltage in the denominator while erroneously concluding the current increases.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=RVI = \frac{R}{V}

    Correct

    I=VRI = \frac{V}{R}

    You inverted the relationship for Ohm's law. Current equals potential difference divided by resistance (I=VRI = \frac{V}{R}), not resistance divided by voltage.

  2. Step 2

    I0=RVI_0 = \frac{R}{V}

    Correct

    I0=VRI_0 = \frac{V}{R}

    This baseline expression directly carries over your inverted formula from the previous step.

  3. Step 3

    Inew=3.00R3.00V=1.00RVI_{\text{new}} = \frac{3.00 R}{3.00 V} = 1.00 \frac{R}{V}

    Correct

    Inew=3.00V3.00R=1.00VRI_{\text{new}} = \frac{3.00 V}{3.00 R} = 1.00 \frac{V}{R}

    You correctly simplified the scale factor 3.003.00=1.00\frac{3.00}{3.00} = 1.00, though the expression still carries the inverted variables.

  4. Step 4

    InewI0=3.00\frac{I_{\text{new}}}{I_0} = 3.00

    Correct

    InewI0=1.00VRVR=1.00\frac{I_{\text{new}}}{I_0} = \frac{1.00 \frac{V}{R}}{\frac{V}{R}} = 1.00

    Even with your expression Inew=1.00RVI_{\text{new}} = 1.00 \frac{R}{V} and I0=RVI_0 = \frac{R}{V}, dividing the two yields 1.00RVRV=1.00\frac{1.00 \frac{R}{V}}{\frac{R}{V}} = 1.00, not 3.003.00.

  5. Step 5

    The current increases.\text{The current increases.}

    Correct

    The current remains unchanged.\text{The current remains unchanged.}

    Because your calculated ratio in step 4 was 3.003.00, you concluded the current increases, whereas a true ratio of 1.001.00 means the current is unchanged.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that three identical resistors in series triple the total resistance to 3.00R3.00 R.

You recognized that the new voltage is 3.00V3.00 V and simplified the fraction 3.003.00\frac{3.00}{3.00} to 1.001.00 in your calculation for InewI_{\text{new}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Ohm's Law Formula

You simplified 3.00R3.00V\frac{3.00 R}{3.00 V} to 1.00RV1.00 \frac{R}{V}, but then wrote a ratio of 3.003.00 instead of 1.001.00 when dividing by I0I_0.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You recalled Ohm's law with resistance in the numerator and voltage in the denominator (I=RVI = \frac{R}{V}). Current is driven by electric potential difference and opposed by resistance, giving I=VRI = \frac{V}{R}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Recall Ohm's Law via Physical Roles
  • Voltage drives charge flow while resistance opposes it: I=VRI = \frac{V}{R} (or V=IRV = I R).

  • Check units: Amperes=VoltsOhms\text{Amperes} = \frac{\text{Volts}}{\text{Ohms}}. If resistance increases at constant voltage, current must decrease.

Evaluate Ratios Consistently
  • The ratio InewI0\frac{I_{\text{new}}}{I_0} is found by dividing the complete algebraic expressions.

  • Substitute your expressions explicitly: 1.00(V/R)1.00(V/R)=1.00\frac{1.00 (V/R)}{1.00 (V/R)} = 1.00.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the standard form of Ohm's law: I=VRI = \frac{V}{R}.

  2. Express baseline current: I0=VRI_0 = \frac{V}{R}.

  3. Substitute the modified values (Vnew=3.00VV_{\text{new}} = 3.00 V, Rnew=3.00RR_{\text{new}} = 3.00 R): Inew=3.00V3.00R=1.00VR=I0I_{\text{new}} = \frac{3.00 V}{3.00 R} = 1.00 \frac{V}{R} = I_0.

  4. Compute the ratio: InewI0=I0I0=1.00\frac{I_{\text{new}}}{I_0} = \frac{I_0}{I_0} = 1.00.

Final answer

The ratio is 1.001.00, and the current remains unchanged.

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the fundamental Ohm's law triangle or equation: V=IRV = I R, which rearranges to I=VRI = \frac{V}{R}.

  • Before writing a ratio, verify that your algebraic division directly follows from your simplified expressions.

OverviewACEpath Teacher's Diagnosis

03 A student assumes current is directly proportional to voltage while ignoring the effect of the increased resistance, yielding a threefold increase.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=VR  ⟹  I0=VRI = \frac{V}{R} \implies I_0 = \frac{V}{R}

  2. Step 2

    Inew=(3.00V)R=3.00(VR)I_{\text{new}} = \frac{(3.00 V)}{R} = 3.00 \left(\frac{V}{R}\right)

    Correct

    Inew=VnewRnew=3.00V3.00R=VRI_{\text{new}} = \frac{V_{\text{new}}}{R_{\text{new}}} = \frac{3.00 V}{3.00 R} = \frac{V}{R}

    You tripled the voltage in the numerator but omitted the simultaneous tripling of the resistance in the denominator, using RR instead of 3.00R3.00 R.

  3. Step 3

    InewI0=3.00  ⟹  The current increases.\frac{I_{\text{new}}}{I_0} = 3.00 \implies \text{The current increases.}

    Correct

    InewI0=1.00  ⟹  The current remains unchanged.\frac{I_{\text{new}}}{I_0} = 1.00 \implies \text{The current remains unchanged.}

    This result follows directly from using an incomplete expression for InewI_{\text{new}} in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied Ohm's law, I=VRI = \frac{V}{R}, to formulate the initial current.

You correctly accounted for the threefold scaling factor on the applied voltage.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Parameter Scaling

You scaled only the voltage by 3.003.00 while keeping resistance as RR, forgetting to plug in the tripled series resistance 3.00R3.00 R.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Failing to account for simultaneous multi-variable scaling in a rational expression. Current depends inversely on resistance, so multiplying both voltage and resistance by the same factor leaves the ratio unaltered.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for all modified parameters
  • When a circuit undergoes multiple simultaneous changes, each modified variable must be replaced by its new scaled expression: V→kVVV \to k_V V and R→kRRR \to k_R R.

  • List every altered parameter explicitly (Vnew=3.00VV_{\text{new}} = 3.00 V, Rnew=3.00RR_{\text{new}} = 3.00 R) before substituting them into I=VRI = \frac{V}{R}.

Evaluate direct vs. inverse proportionality
  • In I=VRI = \frac{V}{R}, current is directly proportional to voltage and inversely proportional to resistance.

  • Verify that scaling both the numerator and denominator by identical factors results in a net scaling factor of kk=1\frac{k}{k} = 1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute both modified parameters into Ohm's law: Inew=VnewRnew=3.00V3.00RI_{\text{new}} = \frac{V_{\text{new}}}{R_{\text{new}}} = \frac{3.00 V}{3.00 R}.

  2. Cancel the common factor of 3.003.00: Inew=VR=I0I_{\text{new}} = \frac{V}{R} = I_0.

  3. Compute the ratio: InewI0=I0I0=1.00\frac{I_{\text{new}}}{I_0} = \frac{I_0}{I_0} = 1.00.

Final answer

1.001.00 (the current remains unchanged)

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out an explicit list of modified variables (VnewV_{\text{new}} and RnewR_{\text{new}}) before writing the new current formula.

  • Practice scaling problems where multiple variables in a fraction change at the same time.

Lock it in

Similar question

01

A simple circuit has an initial current I0I_0. If the voltage source is increased by a factor of 4.04.0 while the circuit resistance is doubled (2.0R2.0 R), determine the ratio InewI0\frac{I_{\text{new}}}{I_0} and state whether the current increases, decreases, or remains unchanged.

Answer

InewI0=2.0\frac{I_{\text{new}}}{I_0} = 2.0, and the current increases.

Key steps:

  1. I0=VRI_0 = \frac{V}{R}
  2. Inew=4.0V2.0R=2.0(VR)=2.0I0I_{\text{new}} = \frac{4.0 V}{2.0 R} = 2.0 \left(\frac{V}{R}\right) = 2.0 I_0
  3. Ratio =2.0I0I0=2.0= \frac{2.0 I_0}{I_0} = 2.0.
02

An engineer adjusts a DC circuit so that the applied voltage drops to 13\frac{1}{3} of its original value. By what factor must the total resistance change so that the current through the circuit remains unchanged?

Answer

The resistance must decrease by a factor of 33 (become 13R\frac{1}{3} R).

Key steps:

  1. I=VRI = \frac{V}{R}
  2. For Inew=I0I_{\text{new}} = I_0, VnewRnew=13VRnew=VR\frac{V_{\text{new}}}{R_{\text{new}}} = \frac{\frac{1}{3} V}{R_{\text{new}}} = \frac{V}{R}
  3. Solving gives Rnew=13RR_{\text{new}} = \frac{1}{3} R.
03

In an experiment, two identical resistors of resistance RR connected in parallel are reconnected in series across a voltage source whose voltage is simultaneously doubled. Determine the ratio of the new total current to the initial total current, IseriesIparallel\frac{I_{\text{series}}}{I_{\text{parallel}}}.

Answer

IseriesIparallel=0.50\frac{I_{\text{series}}}{I_{\text{parallel}}} = 0.50 (or 12\frac{1}{2}).

Key steps:

  1. Initial parallel resistance: Rp=R2  ⟹  Iparallel=VR/2=2VRR_{\text{p}} = \frac{R}{2} \implies I_{\text{parallel}} = \frac{V}{R/2} = \frac{2V}{R}
  2. New series resistance: Rs=2RR_{\text{s}} = 2R, with voltage 2V  ⟹  Iseries=2V2R=VR2V \implies I_{\text{series}} = \frac{2V}{2R} = \frac{V}{R}
  3. Ratio: IseriesIparallel=V/R2V/R=12=0.50\frac{I_{\text{series}}}{I_{\text{parallel}}} = \frac{V/R}{2V/R} = \frac{1}{2} = 0.50.
Loading workspace…