Resources

A liquid calorimeter contains 500 mL500\text{ mL} of pure water at 20.0∘C20.0^\circ\text{C} (density ρ=1.00 g/cm3\rho = 1.00\text{ g}/\text{cm}^3, specific heat capacity cw=4.184 J/(g⋅∘C)c_w = 4.184\text{ J}/(\text{g}\cdot^\circ\text{C})). A submerged immersion heater operating at a power rating of 0.150 kW0.150\text{ kW} is turned on for 1.50 min1.50\text{ min}. Assuming all electrical energy is transferred to the water as heat and heat capacity of the container is negligible, determine: (a) the total heat QQ added in kilojoules (kJ\text{kJ}), (b) the mass mm of the water in kilograms (kg\text{kg}), and (c) the final temperature of the water in degrees Celsius (∘C^\circ\text{C}).

Answer and steps

Final answer

(a) Q=13.5 kJQ = 13.5\text{ kJ}; (b) m=0.500 kgm = 0.500\text{ kg}; (c) Tf=26.5∘CT_f = 26.5^\circ\text{C}.

Steps

Part (a): Total Heat Added (QQ)

  1. Convert the given quantities into SI units:

    • Power rating: P=0.150 kW=0.150×103 W=150 WP = 0.150\text{ kW} = 0.150 \times 10^3\text{ W} = 150\text{ W}
    • Time: t=1.50 min=1.50×60 s=90.0 st = 1.50\text{ min} = 1.50 \times 60\text{ s} = 90.0\text{ s}
  2. Calculate the energy transferred as heat: Since all electrical energy from the heater is transferred to the water: Q=P⋅tQ = P \cdot t Q=150 W×90.0 s=13,500 JQ = 150\text{ W} \times 90.0\text{ s} = 13{,}500\text{ J}
  3. Convert to kilojoules (kJ\text{kJ}): Q=13,500 J1000 J/kJ=13.5 kJQ = \frac{13{,}500\text{ J}}{1000\text{ J/kJ}} = 13.5\text{ kJ}

Part (b): Mass of Water (mm)

  1. Relate volume and density: Since 1 mL=1 cm31\text{ mL} = 1\text{ cm}^3, the volume of water is: V=500 mL=500 cm3V = 500\text{ mL} = 500\text{ cm}^3
  2. Calculate mass: m=ρ⋅V=(1.00 g/cm3)⋅(500 cm3)=500 gm = \rho \cdot V = (1.00\text{ g/cm}^3) \cdot (500\text{ cm}^3) = 500\text{ g}
  3. Convert to kilograms (kg\text{kg}): m=500 g1000 g/kg=0.500 kgm = \frac{500\text{ g}}{1000\text{ g/kg}} = 0.500\text{ kg}

Part (c): Final Temperature (TfT_f)

  1. Use the specific heat equation: The heat absorbed by the water causes an increase in its temperature: Q=m⋅cw⋅ΔTQ = m \cdot c_w \cdot \Delta T where ΔT=Tf−Ti\Delta T = T_f - T_i.
  2. Solve for the temperature change (ΔT\Delta T): Using m=500 gm = 500\text{ g}, cw=4.184 J/(g⋅∘C)c_w = 4.184\text{ J}/(\text{g}\cdot^\circ\text{C}), and Q=13,500 JQ = 13{,}500\text{ J}: ΔT=Qm⋅cw=13,500 J(500 g)⋅(4.184 J/(g⋅∘C))=13,5002092∘C≈6.45∘C\Delta T = \frac{Q}{m \cdot c_w} = \frac{13{,}500\text{ J}}{(500\text{ g}) \cdot (4.184\text{ J}/(\text{g}\cdot^\circ\text{C}))} = \frac{13{,}500}{2092}^\circ\text{C} \approx 6.45^\circ\text{C}
  3. Find the final temperature: Tf=Ti+ΔT=20.0∘C+6.45∘C=26.45∘C≈26.5∘CT_f = T_i + \Delta T = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.45^\circ\text{C} \approx 26.5^\circ\text{C}

Pitfall: Always ensure units are consistent before calculating ΔT\Delta T. If using cwc_w in J/(g⋅∘C)\text{J}/(\text{g}\cdot^\circ\text{C}), express QQ in joules (J\text{J}) and mm in grams (g\text{g}), or convert both mm to kg\text{kg} and cwc_w to J/(kg⋅∘C)\text{J}/(\text{kg}\cdot^\circ\text{C}).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert time from minutes to seconds when calculating energy, resulting in heat being underestimated by a factor of 60.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=0.150 kWP = 0.150\text{ kW}, t=1.50 min  ⟹  Q=0.150 kW⋅1.50=0.225 kJt = 1.50\text{ min} \implies Q = 0.150\text{ kW} \cdot 1.50 = 0.225\text{ kJ}

    Correct

    Q=P⋅t=(150 W)(1.50×60 s)=13,500 J=13.5 kJQ = P \cdot t = (150\text{ W})(1.50 \times 60\text{ s}) = 13{,}500\text{ J} = 13.5\text{ kJ}

    You multiplied power by time directly in minutes. Because a watt is one joule per second (1 W=1 J/s1\text{ W} = 1\text{ J/s}), time must be converted to seconds (1.50 min=90.0 s1.50\text{ min} = 90.0\text{ s}) before multiplying by power.

  2. Step 2

    V=500 mL=500 cm3  ⟹  m=1.00 g/cm3⋅500 cm3=500 g=0.500 kgV = 500\text{ mL} = 500\text{ cm}^3 \implies m = 1.00\text{ g/cm}^3 \cdot 500\text{ cm}^3 = 500\text{ g} = 0.500\text{ kg}

  3. Step 3

    Q=225 J  ⟹  ΔT=225 J500 g⋅4.184 J/(g⋅∘C)≈0.11∘C  ⟹  Tfinal=20.0∘C+0.11∘C=20.11∘CQ = 225\text{ J} \implies \Delta T = \frac{225\text{ J}}{500\text{ g} \cdot 4.184\text{ J/(g}\cdot^\circ\text{C})} \approx 0.11^\circ\text{C} \implies T_{\text{final}} = 20.0^\circ\text{C} + 0.11^\circ\text{C} = 20.11^\circ\text{C}

    Correct

    ΔT=13,500 J(500 g)(4.184 J/(g⋅∘C))≈6.45∘C  ⟹  Tf=20.0∘C+6.45∘C=26.5∘C\Delta T = \frac{13{,}500\text{ J}}{(500\text{ g})(4.184\text{ J/(g}\cdot^\circ\text{C}))} \approx 6.45^\circ\text{C} \implies T_f = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.5^\circ\text{C}

    Your temperature formula and algebraic structure are completely correct, but the result is numerically off because it uses your underestimated value of QQ from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the water's volume and density to determine its mass.

You used the correct heat capacity formula ΔT=Qmcw\Delta T = \frac{Q}{m c_w} and matched the gram units properly.

You correctly added the temperature rise ΔT\Delta T to the initial temperature to find the final temperature.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time unit conversion omitted in $E = P \cdot t$

You treated time as a dimensionless scalar or assumed kilowatt-minutes were equivalent to kilojoules, overlooking the factor of 60 s/min60\text{ s/min}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the definition of power as energy per second (1 W=1 J/s1\text{ W} = 1\text{ J/s} or 1 kW=1 kJ/s1\text{ kW} = 1\text{ kJ/s}), which requires time to be expressed in seconds whenever calculating energy in joules or kilojoules.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Watt in SI Base Units
  • 1 W=1 J/s1\text{ W} = 1\text{ J/s}, and therefore 1 kW=1 kJ/s1\text{ kW} = 1\text{ kJ/s}.

  • Always convert any time duration into seconds before using E=P⋅tE = P \cdot t to find energy in joules or kilojoules.

Verify Calorimetry Unit Consistency
  • If specific heat capacity is given in J/(g⋅∘C)\text{J}/(\text{g}\cdot^\circ\text{C}), heat QQ must be in joules (J\text{J}) and mass mm must be in grams (g\text{g}).

  • Check that QQ and cwc_w share the same energy prefix (both in J\text{J}, not one in kJ\text{kJ} and one in J\text{J}) before computing ΔT\Delta T.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert time to seconds: t=1.50 min×60 s/min=90.0 st = 1.50\text{ min} \times 60\text{ s/min} = 90.0\text{ s}.

  2. Calculate total heat added: Q=P⋅t=(0.150 kW)(90.0 s)=13.5 kJ=13,500 JQ = P \cdot t = (0.150\text{ kW})(90.0\text{ s}) = 13.5\text{ kJ} = 13{,}500\text{ J}.

  3. Compute temperature change: ΔT=13,500 J(500 g)(4.184 J/(g⋅∘C))=13,5002092∘C≈6.45∘C\Delta T = \frac{13{,}500\text{ J}}{(500\text{ g})(4.184\text{ J}/(\text{g}\cdot^\circ\text{C}))} = \frac{13{,}500}{2092}^\circ\text{C} \approx 6.45^\circ\text{C}.

  4. Calculate final temperature: Tf=20.0∘C+6.45∘C=26.5∘CT_f = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.5^\circ\text{C}.

Final answer

(a) Q=13.5 kJQ = 13.5\text{ kJ}; (b) m=0.500 kgm = 0.500\text{ kg}; (c) Tf=26.5∘CT_f = 26.5^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out the full unit chain when computing energy from power: kW×s=kJ\text{kW} \times \text{s} = \text{kJ}.

  • Always convert minutes to seconds right in the given list before substituting into formulas.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert mass from grams to kilograms (or uses kilojoules with specific heat in J/(g·°C) without unit consistency), directly using m = 0.500 kg alongside c_w in J/(g·°C) without matching units, or here directly substituting Q in kJ into Q = m c ΔT without converting kJ to J, yielding a 1000-fold discrepancy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=150 W  ⟹  t=1.50⋅60 s=90 s  ⟹  Q=150 W⋅90 s=13500 J=13.5 kJP = 150\text{ W} \implies t = 1.50 \cdot 60\text{ s} = 90\text{ s} \implies Q = 150\text{ W} \cdot 90\text{ s} = 13500\text{ J} = 13.5\text{ kJ}

  2. Step 2

    m=1.00 g/cm3⋅500 cm3=500 g=0.500 kgm = 1.00\text{ g/cm}^3 \cdot 500\text{ cm}^3 = 500\text{ g} = 0.500\text{ kg}

  3. Step 3

    ΔT=Qm⋅cw=13.5500⋅4.184≈0.00645∘C\Delta T = \frac{Q}{m \cdot c_w} = \frac{13.5}{500 \cdot 4.184} \approx 0.00645^\circ\text{C}

    Correct

    ΔT=Qm⋅cw=13,500 J(500 g)(4.184 J/(g⋅∘C))≈6.45∘C\Delta T = \frac{Q}{m \cdot c_w} = \frac{13{,}500\text{ J}}{(500\text{ g})(4.184\text{ J}/(\text{g}\cdot^\circ\text{C}))} \approx 6.45^\circ\text{C}

    You substituted Q=13.5 kJQ = 13.5\text{ kJ} directly into the numerator while cw=4.184 J/(g⋅∘C)c_w = 4.184\text{ J}/(\text{g}\cdot^\circ\text{C}) is expressed in joules. Because 1 kJ=1000 J1\text{ kJ} = 1000\text{ J}, the heat value must be entered as 13,500 J13{,}500\text{ J} (or cwc_w converted to kJ\text{kJ}) to keep the energy units consistent.

  4. Step 4

    Tfinal=20.0∘C+0.00645∘C=20.006∘CT_{\text{final}} = 20.0^\circ\text{C} + 0.00645^\circ\text{C} = 20.006^\circ\text{C}

    Correct

    Tf=Ti+ΔT=20.0∘C+6.45∘C=26.5∘CT_f = T_i + \Delta T = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.5^\circ\text{C}

    Your addition step followed correct logic, but it inherited the incorrect value of ΔT\Delta T from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted time into seconds and electrical power into watts to calculate total energy correctly.

You converted the liquid volume to mass in both grams and kilograms accurately.

You selected the correct heat equation Q=mcwΔTQ = m c_w \Delta T and rearranged it properly for ΔT\Delta T.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit mismatch in calorimetric equation

You plugged 13.513.5 (from kJ\text{kJ}) into the numerator while the denominator used 4.184 J/(g⋅∘C)4.184\text{ J}/(\text{g}\cdot^\circ\text{C}), mixing kilojoules and joules.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking prefix consistency when evaluating formulas. When specific heat capacity cc contains base joules (J\text{J}), the heat QQ must also be in joules (J\text{J}), not kilojoules (kJ\text{kJ}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Match energy prefixes
  • If specific heat capacity cc is given in J/(g⋅∘C)\text{J}/(\text{g}\cdot^\circ\text{C}) or J/(kg⋅∘C)\text{J}/(\text{kg}\cdot^\circ\text{C}), heat QQ must be substituted in J\text{J}.

  • Check the unit inside the given constant cc; if cc uses J\text{J}, convert QQ from kJ\text{kJ} to J\text{J} before calculating.

Sense check temperature change
  • A heating element delivering 150 W150\text{ W} for 90 s90\text{ s} into a small mug of water (500 mL500\text{ mL}) will cause a noticeable temperature rise of a few degrees, not thousandths of a degree.

  • Compare your calculated ΔT\Delta T against everyday physical intuition to catch order-of-magnitude errors.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute Q=13,500 JQ = 13{,}500\text{ J}, m=500 gm = 500\text{ g}, and cw=4.184 J/(g⋅∘C)c_w = 4.184\text{ J}/(\text{g}\cdot^\circ\text{C}): ΔT=13,500 J(500 g)(4.184 J/(g⋅∘C))=13,5002092∘C≈6.45∘C\Delta T = \frac{13{,}500\text{ J}}{(500\text{ g})(4.184\text{ J}/(\text{g}\cdot^\circ\text{C}))} = \frac{13{,}500}{2092}^\circ\text{C} \approx 6.45^\circ\text{C}.

  2. Compute final temperature: Tf=Ti+ΔT=20.0∘C+6.45∘C=26.45∘C≈26.5∘CT_f = T_i + \Delta T = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.45^\circ\text{C} \approx 26.5^\circ\text{C}.

Final answer

(a) Q=13.5 kJQ = 13.5\text{ kJ}; (b) m=0.500 kgm = 0.500\text{ kg}; (c) Tf=26.5∘CT_f = 26.5^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out explicit units next to every number inside the fraction before computing numerical values.

  • Practice converting between kJ\text{kJ} and J\text{J} whenever using thermal equations involving c=4.184 J/(g⋅∘C)c = 4.184\text{ J}/(\text{g}\cdot^\circ\text{C}).

OverviewACEpath Teacher's Diagnosis

03 The student calculates the temperature change correctly but reports ΔT as the final temperature instead of adding it to the initial temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=0.150 kW=150 W  ⟹  t=1.50⋅60 s=90 s  ⟹  Q=150⋅90=13500 J=13.5 kJP = 0.150\text{ kW} = 150\text{ W} \implies t = 1.50 \cdot 60\text{ s} = 90\text{ s} \implies Q = 150 \cdot 90 = 13500\text{ J} = 13.5\text{ kJ}

  2. Step 2

    m=500 mL⋅1.00 g/cm3=500 g=0.500 kgm = 500\text{ mL} \cdot 1.00\text{ g/cm}^3 = 500\text{ g} = 0.500\text{ kg}

  3. Step 3

    ΔT=13500500⋅4.184=6.45∘C\Delta T = \frac{13500}{500 \cdot 4.184} = 6.45^\circ\text{C}

  4. Step 4

    Tfinal=6.45∘CT_{\text{final}} = 6.45^\circ\text{C}

    Correct

    Tf=Ti+ΔT=20.0∘C+6.45∘C=26.5∘CT_f = T_i + \Delta T = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.5^\circ\text{C}

    You set the final temperature equal to ΔT\Delta T. Because the water was initially at 20.0∘C20.0^\circ\text{C} and absorbed heat, its final temperature must be higher than 20.0∘C20.0^\circ\text{C}, calculated as Tf=Ti+ΔTT_f = T_i + \Delta T.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted all given values into compatible SI units before multiplying.

You used the correct relation between power, time, and heat energy for part (a).

You accurately found the mass of water using its volume and density for part (b).

You correctly rearranged the calorimetry formula to compute the temperature change ΔT\Delta T.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Equating temperature change to final temperature

You stopped after solving for ΔT\Delta T and labeled it as TfinalT_{\text{final}} instead of completing the final addition step.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the temperature difference (ΔT\Delta T) with the absolute final temperature state (TfT_f), overlooking the initial thermal state Ti=20.0∘CT_i = 20.0^\circ\text{C}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish change from state
  • ΔT\Delta T represents how much the temperature changed, not what the thermometer reads at the end: ΔT=Tf−Ti\Delta T = T_f - T_i.

  • Always write out Tf=Ti+ΔTT_f = T_i + \Delta T before plugging in numbers so you do not stop early.

Sanity check heat direction
  • Adding heat to a substance must cause its temperature to rise above its initial temperature (Tf>TiT_f > T_i).

  • Check that your final temperature is greater than 20.0∘C20.0^\circ\text{C} whenever heat is added.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the relationship between initial temperature, temperature change, and final temperature: Tf=Ti+ΔTT_f = T_i + \Delta T.

  2. Substitute Ti=20.0∘CT_i = 20.0^\circ\text{C} and ΔT=6.45∘C\Delta T = 6.45^\circ\text{C}: Tf=20.0∘C+6.45∘C=26.45∘CT_f = 20.0^\circ\text{C} + 6.45^\circ\text{C} = 26.45^\circ\text{C}.

  3. Round to three significant figures to match the given data: Tf=26.5∘CT_f = 26.5^\circ\text{C}.

Final answer

(a) Q=13.5 kJQ = 13.5\text{ kJ}; (b) m=0.500 kgm = 0.500\text{ kg}; (c) Tf=26.5∘CT_f = 26.5^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review flashcards on the definition of temperature change versus final temperature.

  • Practice checking whether your final temperature makes physical sense relative to the initial temperature.

  • Solve the follow-up practice exercises to reinforce adding ΔT\Delta T to TiT_i.

Lock it in

Similar question

01

An electric kettle rated at 1.20 kW1.20\text{ kW} operates for 2.50 min2.50\text{ min}. How much heat energy in kilojoules (kJ\text{kJ}) is transferred to the contents?

Answer

180 kJ180\text{ kJ}. Convert time to seconds: t=2.50×60 s=150 st = 2.50 \times 60\text{ s} = 150\text{ s}. Then Q=P⋅t=1.20 kW×150 s=180 kJQ = P \cdot t = 1.20\text{ kW} \times 150\text{ s} = 180\text{ kJ}.

02

A 250 W250\text{ W} heating coil warms 200 g200\text{ g} of water (specific heat capacity 4.18 J/(g⋅∘C)4.18\text{ J}/(\text{g}\cdot^\circ\text{C})) initially at 18.0∘C18.0^\circ\text{C} for 1.40 min1.40\text{ min}. Assuming zero heat loss, find the final temperature of the water.

Answer

43.1∘C43.1^\circ\text{C}. First convert time: t=1.40×60 s=84 st = 1.40 \times 60\text{ s} = 84\text{ s}. Heat supplied: Q=250 W×84 s=21,000 JQ = 250\text{ W} \times 84\text{ s} = 21{,}000\text{ J}. Temperature rise: ΔT=21,000 J(200 g)(4.18 J/g∘C)≈25.12∘C\Delta T = \frac{21{,}000\text{ J}}{(200\text{ g})(4.18\text{ J/g}^\circ\text{C})} \approx 25.12^\circ\text{C}. Final temperature: Tf=18.0∘C+25.12∘C≈43.1∘CT_f = 18.0^\circ\text{C} + 25.12^\circ\text{C} \approx 43.1^\circ\text{C}.

03

A student wants to raise the temperature of 400 g400\text{ g} of an unknown liquid (c=2.50 J/(g⋅∘C)c = 2.50\text{ J}/(\text{g}\cdot^\circ\text{C})) by 15.0∘C15.0^\circ\text{C} using an immersion heater rated at 75.0 W75.0\text{ W}. How long must the heater run, in minutes?

Answer

3.33 min3.33\text{ min} (or 3 min 20 s3\text{ min } 20\text{ s}). Required heat: Q=mcΔT=(400 g)(2.50 J/(g⋅∘C))(15.0∘C)=15,000 JQ = m c \Delta T = (400\text{ g})(2.50\text{ J}/(\text{g}\cdot^\circ\text{C}))(15.0^\circ\text{C}) = 15{,}000\text{ J}. Time in seconds: t=QP=15,000 J75.0 W=200 st = \frac{Q}{P} = \frac{15{,}000\text{ J}}{75.0\text{ W}} = 200\text{ s}. Converting to minutes gives t=20060≈3.33 mint = \frac{200}{60} \approx 3.33\text{ min}.

Loading workspace…