Resources

A lightweight wrench lies along the positive xx-axis with its socket gripping a bolt at the origin. A force of constant magnitude F=40.0 NF = 40.0\text{ N} is applied at a position vector r⃗=(0.35 m)i^\vec{r} = (0.35\text{ m})\hat{i}. The force is oriented in the xyxy-plane at an angle θ\theta measured counterclockwise from the positive xx-axis, where 0∘<θ<180∘0^\circ < \theta < 180^\circ. If the resulting torque on the bolt about the origin is required to be exactly −7.00 N⋅m  k^-7.00\text{ N}\cdot\text{m}\;\hat{k} (pointing into the page, clockwise), determine the required angle of application ϕ\phi measured below the positive xx-axis (or specify the angle θ\theta in the xyxy-plane).

Answer and steps

Final answer

ϕ=30.0∘\phi = 30.0^\circ below the positive xx-axis (or θ=330.0∘\theta = 330.0^\circ / −30.0∘-30.0^\circ)

Steps

01

Vector Definition of Torque

The torque τ⃗\vec{\tau} exerted by a force F⃗\vec{F} applied at position r⃗\vec{r} relative to the pivot (the origin) is given by the cross product:

τ⃗=r⃗×F⃗\vec{\tau} = \vec{r} \times \vec{F}

Given:

  • Position vector: r⃗=(0.35 m)i^\vec{r} = (0.35\text{ m})\hat{i}
  • Magnitude of force: F=40.0 NF = 40.0\text{ N}
  • Desired torque: τ⃗=−7.00 N⋅m  k^\vec{\tau} = -7.00\text{ N}\cdot\text{m}\;\hat{k}

02

Expressing Force and Torque in Components

In the xyxy-plane, let θ\theta represent the standard direction angle of F⃗\vec{F} measured counterclockwise from the positive xx-axis:

F⃗=(Fcos⁡θ)i^+(Fsin⁡θ)j^\vec{F} = (F\cos\theta)\hat{i} + (F\sin\theta)\hat{j}

Substitute r⃗\vec{r} and F⃗\vec{F} into the cross product:

τ⃗=(ri^)×[(Fcos⁡θ)i^+(Fsin⁡θ)j^]\vec{\tau} = (r\hat{i}) \times \left[(F\cos\theta)\hat{i} + (F\sin\theta)\hat{j}\right]

Since i^×i^=0⃗\hat{i} \times \hat{i} = \vec{0} and i^×j^=k^\hat{i} \times \hat{j} = \hat{k}:

τ⃗=(rFsin⁡θ)k^\vec{\tau} = (r F\sin\theta)\hat{k}


03

Solving for the Angle

Equate the zz-component of torque to the target value:

rFsin⁡θ=−7.00 N⋅mr F \sin\theta = -7.00\text{ N}\cdot\text{m}

Substitute r=0.35 mr = 0.35\text{ m} and F=40.0 NF = 40.0\text{ N}:

(0.35 m)(40.0 N)sin⁡θ=−7.00 N⋅m(0.35\text{ m})(40.0\text{ N})\sin\theta = -7.00\text{ N}\cdot\text{m}

14.0sin⁡θ=−7.0014.0\sin\theta = -7.00

sin⁡θ=−7.0014.0=−0.500\sin\theta = -\frac{7.00}{14.0} = -0.500


04

Interpreting the Direction

A negative value for sin⁡θ\sin\theta indicates that the perpendicular component of the force points in the negative yy-direction, producing a clockwise (negative k^\hat{k}) rotation around the origin:

θ=arcsin⁡(−0.500)=−30.0∘or330.0∘\theta = \arcsin(-0.500) = -30.0^\circ \quad \text{or} \quad 330.0^\circ

Therefore, the force must be directed at an angle of ϕ=30.0∘\phi = 30.0^\circ below the positive xx-axis (corresponding to θ=330.0∘\theta = 330.0^\circ or −30.0∘-30.0^\circ in standard polar coordinates).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the negative sign indicating clockwise torque into the page, wrongly concluding the force must be directed above the positive x-axis.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=r⋅F⋅sin⁡(θ)  ⟹  7.00=(0.35 m)(40.0 N)sin⁡(θ)  ⟹  7.00=14.0sin⁡(θ)\tau = r \cdot F \cdot \sin(\theta) \implies 7.00 = (0.35\text{ m})(40.0\text{ N})\sin(\theta) \implies 7.00 = 14.0\sin(\theta)

    Correct

    τz=rFsin⁡θ  ⟹  −7.00 N⋅m=(0.35 m)(40.0 N)sin⁡θ  ⟹  −7.00=14.0sin⁡θ\tau_z = r F \sin\theta \implies -7.00\text{ N}\cdot\text{m} = (0.35\text{ m})(40.0\text{ N})\sin\theta \implies -7.00 = 14.0\sin\theta

    You substituted the numerical magnitudes correctly, but the problem states the torque is −7.00 N⋅m  k^-7.00\text{ N}\cdot\text{m}\;\hat{k} (pointing into the page, clockwise). The zz-component τz\tau_z must be entered as −7.00-7.00, not +7.00+7.00.

  2. Step 2

    sin⁡(θ)=7.0014.0=0.500  ⟹  θ=arcsin⁡(0.500)=30.0∘\sin(\theta) = \frac{7.00}{14.0} = 0.500 \implies \theta = \arcsin(0.500) = 30.0^\circ

    Correct

    sin⁡θ=−7.0014.0=−0.500  ⟹  θ=−30.0∘ or 330.0∘\sin\theta = -\frac{7.00}{14.0} = -0.500 \implies \theta = -30.0^\circ \text{ or } 330.0^\circ

    Your trigonometry was carried out correctly based on your previous step, but carrying the proper negative sign gives sin⁡θ=−0.500\sin\theta = -0.500, yielding θ=−30.0∘\theta = -30.0^\circ.

  3. Step 3

    Therefore, the force is directed at 30.0∘ above the positive x-axis.\text{Therefore, the force is directed at } 30.0^\circ \text{ above the positive } x\text{-axis.}

    Correct

    Therefore, the force is directed at 30.0∘ below the positive x-axis (or θ=330.0∘ / −30.0∘).\text{Therefore, the force is directed at } 30.0^\circ \text{ below the positive } x\text{-axis (or } \theta = 330.0^\circ \text{ / } -30.0^\circ\text{).}

    Since θ=−30.0∘\theta = -30.0^\circ, the force must push downward into the fourth quadrant (below the positive xx-axis) to produce clockwise rotation.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct formula relating torque magnitude to lever arm, force, and angle.

You computed the product rF=14.0r F = 14.0 and solved the inverse sine equation with accurate arithmetic.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of torque sign convention

You dropped the negative sign from the given torque vector component when substituting into the scalar equation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated torque as an unsigned scalar magnitude rather than a signed vector component along the zz-axis, where positive indicates counterclockwise and negative indicates clockwise.

REASONING PATH
Your ACEpath teacher’s suggested approach
Rotational Sign Convention
  • Counterclockwise torque corresponds to +k^+\hat{k} (positive), while clockwise torque corresponds to −k^-\hat{k} (negative).

  • Always verify the rotational sense of the specified torque before writing the equation; a clockwise torque requires a negative value.

Physical Direction Check
  • With r⃗\vec{r} along +x+x, an upward force (+y+y) produces counterclockwise rotation, whereas a downward force (−y-y) produces clockwise rotation.

  • Sketch the lever arm and force vector to visually confirm whether the force rotates the wrench clockwise or counterclockwise.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Account for the clockwise torque direction by setting τz=−7.00 N⋅m\tau_z = -7.00\text{ N}\cdot\text{m}.

  2. Set up the component equation: −7.00=(0.35 m)(40.0 N)sin⁡θ=14.0sin⁡θ-7.00 = (0.35\text{ m})(40.0\text{ N})\sin\theta = 14.0\sin\theta.

  3. Solve for sin⁡θ\sin\theta: sin⁡θ=−7.0014.0=−0.500\sin\theta = -\frac{7.00}{14.0} = -0.500.

  4. Find the angle: θ=arcsin⁡(−0.500)=−30.0∘\theta = \arcsin(-0.500) = -30.0^\circ, or ϕ=30.0∘\phi = 30.0^\circ below the +x+x-axis.

Final answer

ϕ=30.0∘ below the positive x-axis (or θ=330.0∘ / −30.0∘)\phi = 30.0^\circ \text{ below the positive } x\text{-axis (or } \theta = 330.0^\circ \text{ / } -30.0^\circ\text{)}

NEXT STEPS
Final Takeaways from Your Teacher
  • Include vector unit vectors or component signs explicitly during the initial setup step.

  • Use a quick right-hand-rule sanity check on your final angle to confirm it matches the required direction into or out of the page.

OverviewACEpath Teacher's Diagnosis

02 The student uses the cosine function rather than the sine function to determine the perpendicular component of the force contributing to torque.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=r⋅F⋅cos⁡(ϕ)  ⟹  7.00=(0.35 m)(40.0 N)cos⁡(ϕ)\tau = r \cdot F \cdot \cos(\phi) \implies 7.00 = (0.35\text{ m})(40.0\text{ N})\cos(\phi)

    Correct

    τ=rFsin⁡(ϕ)  ⟹  7.00=(0.35 m)(40.0 N)sin⁡(ϕ)\tau = r F \sin(\phi) \implies 7.00 = (0.35\text{ m})(40.0\text{ N})\sin(\phi)

    Because the position vector r⃗\vec{r} lies along the positive xx-axis and ϕ\phi is the angle measured from this axis, the perpendicular component of force that produces torque is F⊥=Fsin⁡(ϕ)F_\perp = F\sin(\phi), not Fcos⁡(ϕ)F\cos(\phi).

  2. Step 2

    14.0cos⁡(ϕ)=7.00  ⟹  cos⁡(ϕ)=0.50014.0\cos(\phi) = 7.00 \implies \cos(\phi) = 0.500

    Correct

    14.0sin⁡(ϕ)=7.00  ⟹  sin⁡(ϕ)=0.50014.0\sin(\phi) = 7.00 \implies \sin(\phi) = 0.500

    Your algebraic simplification to isolate the trigonometric term was carried out correctly, but it carries forward the incorrect cosine function from Step 1.

  3. Step 3

    ϕ=arccos⁡(0.500)=60.0∘ below the positive x-axis.\phi = \arccos(0.500) = 60.0^\circ\text{ below the positive }x\text{-axis.}

    Correct

    ϕ=arcsin⁡(0.500)=30.0∘ below the positive x-axis.\phi = \arcsin(0.500) = 30.0^\circ\text{ below the positive }x\text{-axis.}

    Evaluating the inverse cosine yields 60.0∘60.0^\circ, but finding the angle from the correct relation sin⁡(ϕ)=0.500\sin(\phi) = 0.500 gives ϕ=30.0∘\phi = 30.0^\circ below the positive xx-axis.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the given values for force magnitude, position vector magnitude, and torque magnitude.

You performed clean and accurate algebraic steps to isolate the trigonometric function and evaluate the inverse angle.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect trigonometric function for torque component

You substituted cos⁡(ϕ)\cos(\phi) instead of sin⁡(ϕ)\sin(\phi) when relating the torque magnitude to the lever arm and applied force.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Torque is defined via the vector cross product τ⃗=r⃗×F⃗\vec{\tau} = \vec{r} \times \vec{F}, whose scalar magnitude is τ=rFsin⁡(ϕ)\tau = r F \sin(\phi), where ϕ\phi is the angle between r⃗\vec{r} and F⃗\vec{F}. The component along the lever arm (Fcos⁡ϕF\cos\phi) acts radially through the pivot and creates zero torque, whereas only the perpendicular component (Fsin⁡ϕF\sin\phi) generates rotational torque.

REASONING PATH
Your ACEpath teacher’s suggested approach
Cross Product vs. Dot Product
  • Torque arises from rotational turning, defined by τ⃗=r⃗×F⃗\vec{\tau} = \vec{r} \times \vec{F}, which scales with sin⁡θ\sin\theta, whereas work is a dot product F⃗⋅d⃗\vec{F} \cdot \vec{d} scaling with cos⁡θ\cos\theta.

  • Always verify whether you need the perpendicular component (Fsin⁡θF\sin\theta for torque) or the parallel component (Fcos⁡θF\cos\theta for work along a line).

Perpendicular Force Component Check
  • If ϕ=0∘\phi = 0^\circ, the force pulls directly outward along the wrench handle, producing zero torque ( sin⁡(0∘)=0 \,\sin(0^\circ) = 0\,).

  • Test the extreme angle ϕ=0∘\phi = 0^\circ in your formula: if your formula predicts maximum torque at 0∘0^\circ, you have mistakenly used cosine instead of sine.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the torque equation using the perpendicular force component: τ=rFsin⁡(ϕ)\tau = r F \sin(\phi).

  2. Substitute the known magnitudes: 7.00 N⋅m=(0.35 m)(40.0 N)sin⁡(ϕ)7.00\text{ N}\cdot\text{m} = (0.35\text{ m})(40.0\text{ N})\sin(\phi).

  3. Solve for sin⁡(ϕ)\sin(\phi): 14.0sin⁡(ϕ)=7.00  ⟹  sin⁡(ϕ)=0.50014.0\sin(\phi) = 7.00 \implies \sin(\phi) = 0.500.

  4. Compute the inverse sine: ϕ=arcsin⁡(0.500)=30.0∘\phi = \arcsin(0.500) = 30.0^\circ.

Final answer

ϕ=30.0∘\phi = 30.0^\circ below the positive xx-axis (or θ=330.0∘\theta = 330.0^\circ / −30.0∘-30.0^\circ)

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric definition of torque magnitude as τ=rFsin⁡θ\tau = r F \sin\theta.

  • Practice decomposing force vectors into radial (parallel to r⃗\vec{r}) and tangential (perpendicular to r⃗\vec{r}) components before calculating torque.

  • Check boundary cases: pulling directly along the wrench handle (0∘0^\circ) gives zero torque, while pulling at 90∘90^\circ gives maximum torque.

OverviewACEpath Teacher's Diagnosis

03 The student solves for the correct reference angle of 30.0° but mistakenly subtracts it from 90° as if finding the complement relative to the y-axis.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ∣τ∣=r⋅F⋅sin⁡(ϕ)  ⟹  7.00=(0.35 m)(40.0 N)sin⁡(ϕ)  ⟹  sin⁡(ϕ)=7.0014.0=0.500|\tau| = r \cdot F \cdot \sin(\phi) \implies 7.00 = (0.35\text{ m})(40.0\text{ N})\sin(\phi) \implies \sin(\phi) = \frac{7.00}{14.0} = 0.500

  2. Step 2

    Reference angle=arcsin⁡(0.500)=30.0∘\text{Reference angle} = \arcsin(0.500) = 30.0^\circ

  3. Step 3

    The angle with the horizontal must be measured from the vertical axis, so ϕ=90.0∘−30.0∘=60.0∘ below the positive x-axis.\text{The angle with the horizontal must be measured from the vertical axis, so } \phi = 90.0^\circ - 30.0^\circ = 60.0^\circ \text{ below the positive } x\text{-axis.}

    Correct

    ϕ=30.0∘ below the positive x-axis (or θ=330.0∘ / −30.0∘)\phi = 30.0^\circ \text{ below the positive } x\text{-axis (or } \theta = 330.0^\circ \text{ / } -30.0^\circ)

    In the torque formula τ=rFsin⁡ϕ\tau = r F \sin\phi, the angle ϕ\phi is defined directly between the position vector r⃗\vec{r} and the force vector F⃗\vec{F}. Because r⃗\vec{r} lies along the positive xx-axis, ϕ\phi is already the angle measured relative to the horizontal axis.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled the magnitude equation for torque, ∣τ∣=rFsin⁡ϕ|\tau| = r F \sin\phi.

You substituted the given numerical values and solved for sin⁡ϕ=0.500\sin\phi = 0.500 accurately.

You correctly computed the inverse sine to get a reference angle of 30.0∘30.0^\circ.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle definition confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that the angle appearing in the torque sine formula was referenced to the vertical axis, leading you to take the complement (90.0∘−30.0∘90.0^\circ - 30.0^\circ). By definition, the angle in τ⃗=r⃗×F⃗\vec{\tau} = \vec{r} \times \vec{F} is measured between r⃗\vec{r} and F⃗\vec{F}, which here is already the angle from the horizontal xx-axis.

REASONING PATH
Your ACEpath teacher’s suggested approach
Geometric Meaning of Angle in Cross Product
  • In τ=rFsin⁡θ\tau = r F \sin\theta, θ\theta is the angle between the position vector r⃗\vec{r} and the force vector F⃗\vec{F}, not an angle relative to a vertical coordinate axis.

  • Identify the direction of r⃗\vec{r} first; if r⃗\vec{r} lies along the xx-axis, the angle in the sine function is already measured directly from the xx-axis.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recognize that r⃗=(0.35 m)i^\vec{r} = (0.35\text{ m})\hat{i} lies along the horizontal xx-axis.

  2. Because ϕ\phi is the angle between r⃗\vec{r} and F⃗\vec{F}, the calculated angle 30.0∘30.0^\circ is already the angle between F⃗\vec{F} and the positive xx-axis.

  3. To produce a clockwise (negative k^\hat{k}) torque, the force must have a negative yy-component, directing it below the positive xx-axis.

Final answer

ϕ=30.0∘ below the positive x-axis\phi = 30.0^\circ \text{ below the positive } x\text{-axis}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric definition of the vector cross product A⃗×B⃗=ABsin⁡θ n^\vec{A} \times \vec{B} = AB\sin\theta\,\hat{n}.

  • Always sketch the vectors r⃗\vec{r} and F⃗\vec{F} tail-to-tail to confirm where the angle θ\theta lies before converting coordinates.

Lock it in

Similar question

01

A uniform horizontal bar lies along the positive xx-axis pivoted at the origin. A force of 20.0 N20.0\text{ N} is applied at r⃗=(0.50 m)i^\vec{r} = (0.50\text{ m})\hat{i}. What angle θ\theta relative to the +x+x-axis produces a torque of −5.00 N⋅m  k^-5.00\text{ N}\cdot\text{m}\;\hat{k}?

Answer

θ=−30.0∘\theta = -30.0^\circ (or 330.0∘330.0^\circ, meaning 30.0∘30.0^\circ below the +x+x-axis). Key steps: τz=rFsin⁡θ  ⟹  −5.00=(0.50)(20.0)sin⁡θ  ⟹  10.0sin⁡θ=−5.00  ⟹  sin⁡θ=−0.500  ⟹  θ=−30.0∘\tau_z = r F \sin\theta \implies -5.00 = (0.50)(20.0)\sin\theta \implies 10.0\sin\theta = -5.00 \implies \sin\theta = -0.500 \implies \theta = -30.0^\circ.

02

A mechanic uses a 0.25 m0.25\text{ m} wrench oriented along the positive xx-axis. A force of magnitude 60.0 N60.0\text{ N} is applied to the end. Find the angle ϕ\phi below the horizontal required to deliver a clockwise torque of magnitude 9.00 N⋅m9.00\text{ N}\cdot\text{m}.

Answer

ϕ=36.9∘\phi = 36.9^\circ below the horizontal. Key steps: Clockwise torque corresponds to τz=−9.00 N⋅m\tau_z = -9.00\text{ N}\cdot\text{m}. Using τz=−rFsin⁡ϕ\tau_z = -r F \sin\phi, we have −9.00=−(0.25)(60.0)sin⁡ϕ  ⟹  15.0sin⁡ϕ=9.00  ⟹  sin⁡ϕ=0.600  ⟹  ϕ=arcsin⁡(0.600)≈36.9∘-9.00 = -(0.25)(60.0)\sin\phi \implies 15.0\sin\phi = 9.00 \implies \sin\phi = 0.600 \implies \phi = \arcsin(0.600) \approx 36.9^\circ.

03

A lever arm extends along the positive yy-axis with a pivot at the origin, with force applied at r⃗=(0.40 m)j^\vec{r} = (0.40\text{ m})\hat{j}. To generate a counterclockwise torque of +8.00 N⋅m  k^+8.00\text{ N}\cdot\text{m}\;\hat{k} using a force of magnitude 25.0 N25.0\text{ N}, what must be the force component FxF_x, and what angle does F⃗\vec{F} make with the negative xx-axis?

Answer

Fx=−20.0 NF_x = -20.0\text{ N}, and the force is directed at an angle of 36.9∘36.9^\circ relative to the negative xx-axis. Key steps: τ⃗=(rj^)×(Fxi^+Fyj^)=−rFxk^\vec{\tau} = (r\hat{j}) \times (F_x\hat{i} + F_y\hat{j}) = -r F_x\hat{k}. Setting −rFx=+8.00-r F_x = +8.00 gives −(0.40)Fx=8.00  ⟹  Fx=−20.0 N-(0.40)F_x = 8.00 \implies F_x = -20.0\text{ N}. Since ∣F⃗∣=25.0 N|\vec{F}| = 25.0\text{ N}, Fy=±25.02−(−20.0)2=±15.0 NF_y = \pm\sqrt{25.0^2 - (-20.0)^2} = \pm 15.0\text{ N}, giving an angle of arctan⁡(15.0/20.0)≈36.9∘\arctan(15.0/20.0) \approx 36.9^\circ above or below the −x-x-axis.

Loading workspace…