Resources

A large open storage tank contains fresh water (ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3) to a depth of H=5.00 mH = 5.00\text{ m}. The tank rests on a elevated horizontal platform such that its base is at an elevation y=3.20 my = 3.20\text{ m} above the flat ground. A small circular orifice is punctured into the vertical wall of the tank at a depth d=1.80 md = 1.80\text{ m} below the water's free surface. The escaping horizontal water jet emerges into the air (Patm=1.01×105 PaP_{\text{atm}} = 1.01\times 10^5\text{ Pa}) and undergoes free-fall projectile motion under gravity before striking the ground. Assuming non-viscous flow and taking g=9.80 m/s2g = 9.80\text{ m/s}^2, find the horizontal distance RR from the vertical plane of the tank wall to the point where the water jet strikes the ground.

Answer and steps

Final answer

R=6.94 mR = 6.94\text{ m}

Steps

01

Velocity of the Escaping Water Jet

We apply Bernoulli's principle along a streamline from the free water surface inside the tank (Point 1) to the exit of the small orifice (Point 2):

P1+12ρv12+ρgz1=P2+12ρv22+ρgz2P_1 + \frac{1}{2}\rho v_1^2 + \rho g z_1 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g z_2

  • Pressures: Both the top surface of the open tank and the emerging jet are exposed to the atmosphere, so P1=P2=PatmP_1 = P_2 = P_{\text{atm}}.
  • Surface velocity: Because the storage tank has a large cross-sectional area compared to the small orifice, the water level drops at an insignificantly slow rate, so v1≈0v_1 \approx 0.
  • Elevations: Choosing the horizontal level of the orifice as the reference elevation (z2=0z_2 = 0), the free surface is at height z1=d=1.80 mz_1 = d = 1.80\text{ m}.

Bernoulli's equation simplifies to Torricelli's law:

ρgd=12ρv2  ⟹  v=2gd\rho g d = \frac{1}{2}\rho v^2 \implies v = \sqrt{2gd}

Substituting the given values:

v=2⋅9.80 m/s2⋅1.80 m=35.28 m/s≈5.94 m/sv = \sqrt{2 \cdot 9.80\text{ m/s}^2 \cdot 1.80\text{ m}} = \sqrt{35.28}\text{ m/s} \approx 5.94\text{ m/s}


02

Height of the Orifice Above the Ground

The vertical position of the orifice above the ground depends on both the platform elevation and the water column:

  • The base of the tank is at an elevation y=3.20 my = 3.20\text{ m} above the ground.
  • The total depth of water in the tank is H=5.00 mH = 5.00\text{ m}, and the orifice is punctured at depth d=1.80 md = 1.80\text{ m} below the water surface.

The height of the orifice above the tank base is:

hbase=H−d=5.00 m−1.80 m=3.20 mh_{\text{base}} = H - d = 5.00\text{ m} - 1.80\text{ m} = 3.20\text{ m}

Therefore, the total vertical height hh of the orifice above the ground is:

h=y+hbase=3.20 m+3.20 m=6.40 mh = y + h_{\text{base}} = 3.20\text{ m} + 3.20\text{ m} = 6.40\text{ m}


03

Time of Flight and Horizontal Range

The water jet exits horizontally, meaning its initial vertical velocity component is zero (vy0=0v_{y0} = 0). Under the uniform acceleration of gravity gg, the time tt required for the water to fall through height hh to the ground is:

h=12gt2  ⟹  t=2hgh = \frac{1}{2}gt^2 \implies t = \sqrt{\frac{2h}{g}}

Substituting h=6.40 mh = 6.40\text{ m} and g=9.80 m/s2g = 9.80\text{ m/s}^2:

t=2⋅6.40 m9.80 m/s2≈1.17 st = \sqrt{\frac{2 \cdot 6.40\text{ m}}{9.80\text{ m/s}^2}} \approx 1.17\text{ s}

The horizontal distance RR traveled by the jet before striking the ground is:

R=v⋅t=2gd⋅2hg=2d⋅hR = v \cdot t = \sqrt{2gd} \cdot \sqrt{\frac{2h}{g}} = 2\sqrt{d \cdot h}

Evaluating the range:

R=21.80 m⋅6.40 m≈6.94 mR = 2\sqrt{1.80\text{ m} \cdot 6.40\text{ m}} \approx 6.94\text{ m}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to include the elevation of the platform when calculating the height of the orifice above the ground, using only the height above the tank bottom.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=2gd=2×9.80×1.80=5.94 m/sv = \sqrt{2gd} = \sqrt{2 \times 9.80 \times 1.80} = 5.94\text{ m/s}

  2. Step 2

    h=H−d=5.00−1.80=3.20 mh = H - d = 5.00 - 1.80 = 3.20\text{ m}

    Correct

    h=y+(H−d)=3.20 m+(5.00 m−1.80 m)=6.40 mh = y + (H - d) = 3.20\text{ m} + (5.00\text{ m} - 1.80\text{ m}) = 6.40\text{ m}

    You found the height of the orifice above the bottom of the tank, but the tank is resting on an elevated platform 3.20 m3.20\text{ m} above the ground. You need to add this platform elevation to get the full vertical distance the water falls.

  3. Step 3

    t=2h/g=2×3.209.80=0.808 st = \sqrt{2h/g} = \sqrt{\frac{2 \times 3.20}{9.80}} = 0.808\text{ s}

    Correct

    t=2hg=2⋅6.40 m9.80 m/s2≈1.17 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \cdot 6.40\text{ m}}{9.80\text{ m/s}^2}} \approx 1.17\text{ s}

    Your kinematic formula for time of flight is correct, but your calculated time was affected by the incomplete height from Step 2.

  4. Step 4

    R=v×t=5.94×0.808=4.80 mR = v \times t = 5.94 \times 0.808 = 4.80\text{ m}

    Correct

    R=v⋅t=2d⋅h≈6.94 mR = v \cdot t = 2\sqrt{d \cdot h} \approx 6.94\text{ m}

    You multiplied your velocity by your time of flight correctly, but the resulting range is lower than expected due to the earlier height error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied Torricelli's theorem to find the horizontal exit speed of the jet.

You used the correct kinematic relation for the time of flight of a horizontal projectile.

You correctly related the horizontal range to the product of horizontal speed and time of flight.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted reference elevation / platform height

You calculated the height of the hole above the tank base rather than above the ground where the jet lands.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking that the landing surface lies at a different datum level than the bottom of the container. In multi-level projectile or Torricelli problems, the vertical distance fallen is measured relative to the final impact plane, not the tank floor.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish the Global Ground Datum
  • The vertical displacement of a projectile is Δy=yimpact−ylaunch\Delta y = y_{\text{impact}} - y_{\text{launch}}.

  • Always sketch the setup and sum all vertical segments between the orifice and the actual landing ground: h=yplatform+hbaseh = y_{\text{platform}} + h_{\text{base}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate total height above the ground: h=y+(H−d)=3.20 m+3.20 m=6.40 mh = y + (H - d) = 3.20\text{ m} + 3.20\text{ m} = 6.40\text{ m}.

  2. Compute the correct time of flight: t=2hg=2⋅6.409.80≈1.17 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \cdot 6.40}{9.80}} \approx 1.17\text{ s}.

  3. Calculate the horizontal range: R=v⋅t=5.94 m/s⋅1.17 s≈6.94 mR = v \cdot t = 5.94\text{ m/s} \cdot 1.17\text{ s} \approx 6.94\text{ m}.

Final answer

R=6.94 mR = 6.94\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a quick vertical diagram marking the datum line at the landing surface before extracting numeric values.

  • Label two separate vertical dimensions: depth below the liquid surface (dd) for exit speed, and total height above the landing ground (hh) for fall time.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the depth below the surface with the height above the tank base when calculating the efflux velocity, using H - d instead of d in Torricelli's law.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=2g(H−d)=2×9.80×3.20=7.92 m/sv = \sqrt{2g(H-d)} = \sqrt{2 \times 9.80 \times 3.20} = 7.92\text{ m/s}

    Correct

    v=2gd=2×9.80×1.80≈5.94 m/sv = \sqrt{2gd} = \sqrt{2 \times 9.80 \times 1.80} \approx 5.94\text{ m/s}

    By Bernoulli's principle, the pressure driving fluid out of the orifice depends on the hydrostatic head above it, which is the depth d=1.80 md = 1.80\text{ m} measured downward from the free surface, not the height of water remaining below the hole.

  2. Step 2

    h=(H−d)+y=3.20+3.20=6.40 mh = (H-d) + y = 3.20 + 3.20 = 6.40\text{ m}

  3. Step 3

    t=2h/g=2×6.409.80=1.14 st = \sqrt{2h/g} = \sqrt{\frac{2 \times 6.40}{9.80}} = 1.14\text{ s}

  4. Step 4

    R=v×t=7.92×1.14=9.03 mR = v \times t = 7.92 \times 1.14 = 9.03\text{ m}

    Correct

    R=v×t=5.94×1.143≈6.94 mR = v \times t = 5.94 \times 1.143 \approx 6.94\text{ m}

    Your multiplication step followed your values correctly, but the result was affected by the initial velocity error in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly determined the vertical drop of the orifice above the ground by combining the platform height and the fluid height below the hole.

You correctly modeled the escaping horizontal jet as a horizontal projectile in free fall to find the flight time.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing depth below surface with height above base in Torricelli's law

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted the height of the orifice above the tank bottom (H−d=3.20 m)(H - d = 3.20\text{ m}) into Torricelli's equation instead of the fluid depth above the orifice (d=1.80 m)(d = 1.80\text{ m}). Torricelli's efflux velocity v=2ghv = \sqrt{2gh} depends purely on the vertical liquid column resting above the exit level, where potential energy is converted to kinetic energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Fluid Depth vs. Base Height
  • In Torricelli's law v=2gdv = \sqrt{2gd}, dd is strictly the depth measured downward from the top liquid surface to the orifice (zsurface−zholez_{\text{surface}} - z_{\text{hole}}).

  • Always draw a vertical line from the free surface down to the hole and verify that your variable represents the column of water sitting above the opening.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. v=2gd=2×9.80 m/s2×1.80 m=35.28 m/s≈5.940 m/sv = \sqrt{2gd} = \sqrt{2 \times 9.80\text{ m/s}^2 \times 1.80\text{ m}} = \sqrt{35.28}\text{ m/s} \approx 5.940\text{ m/s}

  2. h=(H−d)+y=(5.00−1.80)+3.20=6.40 mh = (H - d) + y = (5.00 - 1.80) + 3.20 = 6.40\text{ m}

  3. t=2hg=2×6.409.80≈1.143 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \times 6.40}{9.80}} \approx 1.143\text{ s}

  4. R=v×t=5.940 m/s×1.143 s≈6.94 mR = v \times t = 5.940\text{ m/s} \times 1.143\text{ s} \approx 6.94\text{ m}

Final answer

R=6.94 mR = 6.94\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the fluid container and explicitly label both haboveh_{\text{above}} (depth from surface, driving efflux) and hbelowh_{\text{below}} (height above ground, governing projectile flight time).

  • Practice setting up Bernoulli's equation from the top surface to the orifice to reinforce why the depth below the surface determines exit velocity.

OverviewACEpath Teacher's Diagnosis

03 The student uses the total water depth H instead of the depth d below the surface when finding the efflux velocity via Torricelli's law.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=2gH=2×9.80×5.00=9.90 m/sv = \sqrt{2gH} = \sqrt{2 \times 9.80 \times 5.00} = 9.90\text{ m/s}

    Correct

    v=2gd=2⋅9.80 m/s2⋅1.80 m≈5.94 m/sv = \sqrt{2gd} = \sqrt{2 \cdot 9.80\text{ m/s}^2 \cdot 1.80\text{ m}} \approx 5.94\text{ m/s}

    Torricelli's law derives from Bernoulli's equation evaluated between the top surface and the orifice. The head driving the efflux speed is the depth from the liquid surface down to the hole (d=1.80 md = 1.80\text{ m}), not the total fluid depth HH.

  2. Step 2

    h=(H−d)+y=3.20+3.20=6.40 mh = (H - d) + y = 3.20 + 3.20 = 6.40\text{ m}

  3. Step 3

    t=2hg=2×6.409.80=1.14 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \times 6.40}{9.80}} = 1.14\text{ s}

  4. Step 4

    R=v×t=9.90×1.14=11.29 mR = v \times t = 9.90 \times 1.14 = 11.29\text{ m}

    Correct

    R=v⋅t=(5.94 m/s)(1.14 s)≈6.94 mR = v \cdot t = (5.94\text{ m/s})(1.14\text{ s}) \approx 6.94\text{ m}

    Your formula for horizontal distance is correct, but the numerical result is affected by the incorrect efflux speed from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established the total falling height of the jet by combining the tank elevation and the height of the hole above the tank base.

You applied the horizontal projectile motion kinematics correctly to relate height, time of flight, and range.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing total liquid depth with orifice depth in Torricelli's law

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted the total liquid depth H=5.00 mH = 5.00\text{ m} into Torricelli's law instead of the depth of the hole beneath the free liquid surface (d=1.80 md = 1.80\text{ m}). Bernoulli's principle depends on the difference in hydrostatic head between the open water surface and the exit point.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Driving Head
  • In Torricelli's law v=2gΔzv = \sqrt{2g\Delta z}, Δz\Delta z is the vertical distance from the free liquid surface down to the orifice.

  • Measure the vertical distance strictly from the top surface of the fluid to the center of the puncture hole.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct horizontal exit velocity using the depth below the surface: v=2gd=2⋅9.80⋅1.80=35.28≈5.94 m/sv = \sqrt{2gd} = \sqrt{2 \cdot 9.80 \cdot 1.80} = \sqrt{35.28} \approx 5.94\text{ m/s}.

  2. Use the calculated time of flight t=2hg=2⋅6.409.80≈1.143 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \cdot 6.40}{9.80}} \approx 1.143\text{ s}.

  3. Compute the horizontal range: R=v⋅t=5.94 m/s⋅1.143 s≈6.94 mR = v \cdot t = 5.94\text{ m/s} \cdot 1.143\text{ s} \approx 6.94\text{ m}.

Final answer

R≈6.94 mR \approx 6.94\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Re-evaluate Torricelli's law by drawing a streamline between the water surface and the orifice to clearly identify the vertical separation Δz\Delta z.

  • Practice distinguishing between total tank height, hole depth below the water line, and hole elevation above ground level.

Lock it in

Similar question

01

A cylindrical barrel of height 2.0 m2.0\text{ m} is filled to the brim with water and rests on a table of height 1.5 m1.5\text{ m} above the floor. A hole is drilled 0.8 m0.8\text{ m} below the water surface. Taking g=9.8 m/s2g = 9.8\text{ m/s}^2, find the horizontal distance from the base of the table to where the water hits the floor.

Answer

R≈4.65 mR \approx 4.65\text{ m}. Key steps: v=2gd=2(9.8)(0.8)=3.96 m/sv = \sqrt{2gd} = \sqrt{2(9.8)(0.8)} = 3.96\text{ m/s}. The hole is 2.0−0.8=1.2 m2.0 - 0.8 = 1.2\text{ m} above the table, so height above floor is h=1.5+1.2=2.7 mh = 1.5 + 1.2 = 2.7\text{ m}. Time of flight is t=2(2.7)/9.8≈0.742 st = \sqrt{2(2.7)/9.8} \approx 0.742\text{ s}. Range R=vt=3.96⋅0.742≈2.94 mR = vt = 3.96 \cdot 0.742 \approx 2.94\text{ m} (or using R=2d⋅h=20.8⋅2.7≈2.94 mR = 2\sqrt{d \cdot h} = 2\sqrt{0.8 \cdot 2.7} \approx 2.94\text{ m}).

02

An open water tank with total depth H=4.0 mH = 4.0\text{ m} stands on a platform of height y=2.0 my = 2.0\text{ m}. At what depth dd below the water surface should a hole be punctured so that the emerging horizontal jet achieves the maximum possible horizontal range on the ground?

Answer

d=3.0 md = 3.0\text{ m}. Key steps: Total height of surface above ground is Htot=H+y=4.0+2.0=6.0 mH_{\text{tot}} = H + y = 4.0 + 2.0 = 6.0\text{ m}. The height of the orifice above ground is h=6.0−dh = 6.0 - d. The range is R=2d⋅h=2d(6.0−d)R = 2\sqrt{d \cdot h} = 2\sqrt{d(6.0 - d)}. This product is maximized when d=h=6.02=3.0 md = h = \frac{6.0}{2} = 3.0\text{ m}. Since 3.0 m<4.0 m3.0\text{ m} < 4.0\text{ m}, the hole is on the tank wall at d=3.0 md = 3.0\text{ m}.

03

A pressurized closed tank has an internal air gauge pressure of ΔP=1.96×104 Pa\Delta P = 1.96 \times 10^4\text{ Pa} above a water column of depth H=3.0 mH = 3.0\text{ m}. The tank rests on a platform 2.5 m2.5\text{ m} above the ground. A small orifice is opened at depth d=1.0 md = 1.0\text{ m} below the water surface. Taking ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3 and g=9.8 m/s2g = 9.8\text{ m/s}^2, find the horizontal range of the jet on the ground.

Answer

R≈10.2 mR \approx 10.2\text{ m}. Key steps: Effective pressure head is hp=ΔPρg=196001000⋅9.8=2.0 mh_p = \frac{\Delta P}{\rho g} = \frac{19600}{1000 \cdot 9.8} = 2.0\text{ m}. Exit velocity v=2g(d+hp)=2(9.8)(1.0+2.0)=58.8≈7.67 m/sv = \sqrt{2g(d + h_p)} = \sqrt{2(9.8)(1.0 + 2.0)} = \sqrt{58.8} \approx 7.67\text{ m/s}. Height above ground is h=y+(H−d)=2.5+(3.0−1.0)=4.5 mh = y + (H - d) = 2.5 + (3.0 - 1.0) = 4.5\text{ m}. Flight time t=2(4.5)/9.8≈0.958 st = \sqrt{2(4.5)/9.8} \approx 0.958\text{ s}. Range R=vt=7.67×0.958≈7.35 mR = vt = 7.67 \times 0.958 \approx 7.35\text{ m}.

Loading workspace…