Resources
A package of mass slides down a rough ramp inclined at an unknown angle to the horizontal. A standard tilted coordinate system is established with the -axis directed down the incline and the -axis directed perpendicular to and upward from the surface. The coefficient of kinetic friction between the ramp and the package is . During the descent, the magnitude of the normal force acting along the -axis is measured to be . Using , find: (a) the incline angle , (b) the component of gravity acting along the tilted -axis, , and (c) the net acceleration down the ramp.
Answer and steps
Final answer
(a) , (b) , (c)
Steps
Set Up the Tilted Coordinate System
Aligning the axes with the geometry of motion simplifies two-dimensional dynamics into two independent one-dimensional problems:
- Let the -axis point down along the incline, parallel to the surface.
- Let the -axis point perpendicular to the incline, directed outward/upward.
Resolving the gravitational force vector (magnitude ) into these rotated axes yields:
- Perpendicular component: (acting in the direction)
- Parallel component: (acting in the direction)
The total weight of the package is:
Determine the Incline Angle
Because the package remains on the surface, there is no acceleration perpendicular to the ramp (). Applying Newton's second law along the -axis:
Substitute the given normal force :
Calculate the Parallel Component of Gravity
Using the angle :
Determine the Net Acceleration
Because the package slides down the incline in the direction, kinetic friction opposes this motion and acts in the direction:
Applying Newton's second law along the -axis:
Substitute the known values:
Key Pitfall: Do not confuse which trigonometric function applies to which component. Because the incline angle is measured relative to the horizontal, the angle between the vertical gravity vector and the perpendicular axis () is also . Therefore, the perpendicular component uses , and the parallel component uses .
Typical errors
01 The student swaps sine and cosine for the tilted components of gravity, using F_N = m g sin(θ) instead of m g cos(θ).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the ramp angle is measured relative to the horizontal, the angle between the vertically downward gravity vector and the perpendicular -axis is also . Therefore, the perpendicular balance equation is , which yields .
- Step 2Correct
The component of gravity directed down the incline is opposite to angle in the force triangle, so it should be . Because you evaluated , your numerical result happened to match , but the formula was reversed.
- Step 3
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the normal force balances the perpendicular component of gravity.
You calculated the total weight and the kinetic friction force with exact arithmetic.
You correctly set up Newton's second law along the inclined axis.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou associated the vertical/perpendicular axis with sine and the horizontal/parallel axis with cosine by default, reversing the correct projection for an incline measured from the horizontal.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOn a flat surface with an angle from the horizontal, vertical forces typically take and horizontal forces take . However, on an incline of angle to the horizontal, tilting the axes rotates this geometry: the angle between and the normal (-axis) is , making the perpendicular component adjacent () and the parallel component opposite ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Extreme-Angle Sanity Check
As an incline flattens (), the normal force must approach full weight () and sliding force down the ramp must approach zero.
Check: does your perpendicular component have () and does your parallel component have ()?
- Geometric Triangle Check
In the right triangle formed by , , and , the angle at the top between and the perpendicular axis equals the incline angle .
Identify as the adjacent side () and as the opposite side ().
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the perpendicular forces in equilibrium: .
Substitute the numerical values: .
Calculate the incline angle: .
(a) , (b) , (c)
02 The student calculates kinetic friction using the full weight instead of the normal force, writing f_k = μ_k m g.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
F_N = mg \cos() \cos() = = = 0.7228 = \arccos(0.7228) = 43.7^
- Step 2
F_{gx} = mg \sin() = 12.0 9.80 \sin(43.71^) = 81.3_
- Step 3
f_k = k mg = 0.250 12.0 9.80 = 29.4
Correctf_k = k F_N = (0.250)(85.0) = 21.25
By definition, kinetic friction is proportional to the normal force pressing the surfaces together (). On an inclined plane, ; here, was already measured and given.
- Step 4
\sum F_x = F_{gx} - f_k = ma_x a_x = = 4.33^2_
Correcta_x = = 5.00^2
Your Newton's second law formulation along the -axis was completely correct, but substituting the incorrect friction value carried over into the final acceleration.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved gravity into tilted parallel () and perpendicular () components.
You accurately balanced forces along the -axis to determine the incline angle .
You correctly set up Newton's second law along the -axis as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou actually had the correct value () written down first, but crossed it out to recalculate friction as .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating the general definition of friction () with the special case of a horizontal surface without vertical applied forces where . On any inclined surface, the normal force is less than the object's total weight.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Friction
always, whereas is only valid when on a flat horizontal plane.
Always identify and substitute the actual normal force from the perpendicular force balance into .
- Checking Perpendicular Contact Force
On an incline of angle with no additional vertical forces, .
Verify that the friction force is strictly smaller than whenever an incline is present.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute the given normal force into the friction formula: .
Apply Newton's second law along the tilted -axis: .
Substitute the values: .
Solve for acceleration: .
(a) , (b) , (c)
03 The student forgets to account for friction in the net force equation along the incline, setting m a_x = F_gx.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
\sum F_x = F_{gx} = m a_x a_x = = 6.78^2_
Correct\sum F_x = F_{gx} - f_k = m a_x a_x = = 5.00^2_
You omitted the kinetic friction force , which opposes the package's downward motion along the -axis.
WHAT YOU DID WELL
Compliments from Your TeacherYou properly set up the tilted coordinate system and recognized that acceleration perpendicular to the ramp is zero.
You correctly used the normal force to solve for the incline angle .
You correctly computed the downhill component of gravity, .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the downhill component of gravity as the only force acting along the inclined surface, overlooking the rough surface friction explicitly described in the problem statement.
REASONING PATH
Your ACEpath teacher’s suggested approach- Account for all surface interactions
When an object moves along a rough surface, kinetic friction acts parallel to the surface opposite to the direction of relative velocity.
Always draw a free-body diagram along the -axis and verify whether contact surfaces have a non-zero coefficient of friction before writing .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the magnitude of kinetic friction: .
Write Newton's second law along the incline, taking the downward direction as positive: .
Substitute the known values: .
Solve for the acceleration: .
Lock it in
For an object on a ramp inclined at angle above the horizontal, which trigonometric functions represent the components of gravity parallel () and perpendicular () to the ramp?
(down the ramp) and (perpendicular into the ramp). Remember: as , the ramp flattens, so and .
Similar question
A crate rests on a frictionless incline angled at above the horizontal. Find: (a) the magnitude of the normal force exerted by the surface, and (b) the acceleration of the crate down the ramp. (Use .)
Answer
(a) . (b) down the ramp.
A block is placed on a rough ramp inclined at an angle to the horizontal. If the measured normal force is and , find: (a) the angle , and (b) the minimum coefficient of static friction required to prevent the block from slipping.
Answer
(a) . (b) For impending slip, .
A sled is pulled up a incline at constant velocity by a rope parallel to the slope. The coefficient of kinetic friction is . Using , find: (a) the normal force , (b) the kinetic friction force , and (c) the tension in the rope.
Answer
(a) . (b) directed down the ramp. (c) At constant velocity, .