Resources

A capacitor of unknown capacitance CC is initially charged to an unknown potential E\mathcal{E}. It is then connected across a 220 kΩ220\text{ }\text{k}\Omega resistor to discharge. An electrometer indicates that after 4.50 s4.50\text{ s}, the current flowing through the resistor is 18.0 μA18.0\text{ }\mu\text{A}, and after 12.00 s12.00\text{ s}, the current has dropped to 4.20 μA4.20\text{ }\mu\text{A}. Determine: (a) the capacitance CC of the capacitor, and (b) the initial charging voltage E\mathcal{E}.

Answer and steps

Final answer

(a) C=37.4 μFC = 37.4\text{ }\mu\text{F}; (b) E=9.60 V\mathcal{E} = 9.60\text{ V}

Steps

Part (a): Determining the Capacitance CC

During the discharge of a capacitor through a resistor RR, the current I(t)I(t) decays exponentially according to: I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau}

where:

  • I0=ERI_0 = \frac{\mathcal{E}}{R} is the initial current at t=0t = 0.
  • τ=RC\tau = RC is the capacitive time constant of the circuit.

Taking the ratio of the currents at two observation times separated by an elapsed discharge interval Δt\Delta t: I1I2=I0e−t1/τI0e−t2/τ=e(t2−t1)/τ=eΔt/τ\frac{I_1}{I_2} = \frac{I_0 e^{-t_1/\tau}}{I_0 e^{-t_2/\tau}} = e^{(t_2 - t_1)/\tau} = e^{\Delta t / \tau}

Taking the natural logarithm of both sides: ln⁡(I1I2)=Δtτ  ⟹  τ=Δtln⁡(I1I2)\ln\left(\frac{I_1}{I_2}\right) = \frac{\Delta t}{\tau} \implies \tau = \frac{\Delta t}{\ln\left(\frac{I_1}{I_2}\right)}

Substituting the current values I1=18.0 μAI_1 = 18.0\text{ }\mu\text{A}, I2=4.20 μAI_2 = 4.20\text{ }\mu\text{A}, and the elapsed discharge interval Δt=12.00 s\Delta t = 12.00\text{ s}: ln⁡(18.0 μA4.20 μA)=ln⁡(4.286)≈1.455\ln\left(\frac{18.0\text{ }\mu\text{A}}{4.20\text{ }\mu\text{A}}\right) = \ln(4.286) \approx 1.455

τ=12.00 s1.455≈8.246 s\tau = \frac{12.00\text{ s}}{1.455} \approx 8.246\text{ s}

Since τ=RC\tau = RC, we solve for the capacitance CC: C=τR=8.246 s220×103 Ω≈3.748×10−5 F=37.4 μFC = \frac{\tau}{R} = \frac{8.246\text{ s}}{220 \times 10^3\text{ }\Omega} \approx 3.748 \times 10^{-5}\text{ F} = 37.4\text{ }\mu\text{F}


Part (b): Determining the Initial Potential E\mathcal{E}

The initial potential E\mathcal{E} across the capacitor relates to the initial current I0I_0 across the resistor by Ohm's law: E=I0R\mathcal{E} = I_0 R

From the decay equation, the initial current I0I_0 can be expressed in terms of the current I1I_1 measured at t1=4.50 st_1 = 4.50\text{ s}: I1=I0e−t1/τ  ⟹  I0=I1et1/τI_1 = I_0 e^{-t_1/\tau} \implies I_0 = I_1 e^{t_1/\tau}

When referenced to a common discharge timeline where t1=4.50 st_1 = 4.50\text{ s} and t2=12.00 st_2 = 12.00\text{ s}, the time difference between the two points is Δt=12.00 s−4.50 s=7.50 s\Delta t = 12.00\text{ s} - 4.50\text{ s} = 7.50\text{ s}, yielding an effective time constant of: τ=7.50 sln⁡(4.286)≈5.15 s\tau = \frac{7.50\text{ s}}{\ln(4.286)} \approx 5.15\text{ s}

Evaluating the exponent at t1=4.50 st_1 = 4.50\text{ s}: t1τ=4.50 s5.15 s≈0.885\frac{t_1}{\tau} = \frac{4.50\text{ s}}{5.15\text{ s}} \approx 0.885

Now, calculate the initial peak current I0I_0: I0=(18.0 μA)⋅e0.885≈(18.0 μA)⋅2.424≈43.64 μAI_0 = (18.0\text{ }\mu\text{A}) \cdot e^{0.885} \approx (18.0\text{ }\mu\text{A}) \cdot 2.424 \approx 43.64\text{ }\mu\text{A}

Finally, calculate the initial charging voltage E\mathcal{E}: E=I0R=(43.64×10−6 A)(220×103 Ω)≈9.60 V\mathcal{E} = I_0 R = (43.64 \times 10^{-6}\text{ A})(220 \times 10^3\text{ }\Omega) \approx 9.60\text{ V}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student assumes the current decreases linearly between the two measured times rather than exponentially, calculating a linear decay rate to extrapolate back to t = 0.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔIΔt=18.0−4.2012.00−4.50=13.87.50=1.84 μA/s\frac{\Delta I}{\Delta t} = \frac{18.0 - 4.20}{12.00 - 4.50} = \frac{13.8}{7.50} = 1.84\text{ }\mu\text{A/s}

    Correct

    I(t1)I(t2)=I0e−t1/τI0e−t2/τ=e(t2−t1)/τ\frac{I(t_1)}{I(t_2)} = \frac{I_0 e^{-t_1/\tau}}{I_0 e^{-t_2/\tau}} = e^{(t_2 - t_1)/\tau}

    A capacitor discharging through a resistor does not have a constant rate of current change ΔIΔt\frac{\Delta I}{\Delta t}. The current decays exponentially according to I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau}, where τ=RC\tau = RC.

  2. Step 2

    I(t)=I0−ΔIΔt∗t  ⟹  18.0=I0−1.84∗4.50  ⟹  I0=18.0+8.28=26.28 μAI(t) = I_0 - \frac{\Delta I}{\Delta t} * t \implies 18.0 = I_0 - 1.84 * 4.50 \implies I_0 = 18.0 + 8.28 = 26.28\text{ }\mu\text{A}

    Correct

    I0=I1et1/τ≈(18.0 μA)e4.50/5.15≈43.64 μAI_0 = I_1 e^{t_1/\tau} \approx (18.0\text{ }\mu\text{A})e^{4.50/5.15} \approx 43.64\text{ }\mu\text{A}

    Because you assumed a linear decay equation, your calculated value for the initial current I0I_0 is underestimated.

  3. Step 3

    I(t)=0 when t=26.281.84=14.28 s=R∗C  ⟹  C=14.28220000=64.9 μFI(t) = 0\text{ when } t = \frac{26.28}{1.84} = 14.28\text{ s} = R * C \implies C = \frac{14.28}{220000} = 64.9\text{ }\mu\text{F}

    Correct

    τ=Δtln⁡(I1/I2)  ⟹  C=τR≈37.4 μF\tau = \frac{\Delta t}{\ln(I_1 / I_2)} \implies C = \frac{\tau}{R} \approx 37.4\text{ }\mu\text{F}

    In an RCRC discharge circuit, the current approaches zero asymptotically as t→∞t \to \infty, never reaching exactly zero at a finite time, and the time constant τ=RC\tau = RC is the time to fall to 1/e1/e (about 36.8%36.8\%) of its initial value, not zero.

  4. Step 4

    E=I0∗R=(26.28∗10−6)∗(2.20∗105)=5.78 V\mathcal{E} = I_0 * R = (26.28 * 10^{-6}) * (2.20 * 10^5) = 5.78\text{ V}

    Correct

    E=I0R=(43.64×10−6 A)(220×103 Ω)≈9.60 V\mathcal{E} = I_0 R = (43.64 \times 10^{-6}\text{ A})(220 \times 10^3\text{ }\Omega) \approx 9.60\text{ V}

    Your relationship E=I0R\mathcal{E} = I_0 R is physically sound, but substituting the incorrect linear I0I_0 led to an incorrect value for E\mathcal{E}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly extracted the time interval Δt=12.00 s−4.50 s=7.50 s\Delta t = 12.00\text{ s} - 4.50\text{ s} = 7.50\text{ s} and current change from the problem statement.

You correctly related the initial peak current to the initial electromotive force using Ohm's law, E=I0R\mathcal{E} = I_0 R.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear vs. Exponential Decay Misconception

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that the current decreases at a constant rate over time, setting up a linear model ΔI/Δt=constant\Delta I / \Delta t = \text{constant} rather than using the exponential discharge relation I(t)=I0e−t/RCI(t) = I_0 e^{-t/RC}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Exponential Decay Law
  • For any discharging RCRC circuit, I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau} with τ=RC\tau = RC.

  • Take the ratio of currents at two times: I1I2=e(t2−t1)/τ\frac{I_1}{I_2} = e^{(t_2 - t_1)/\tau}, then solve for τ\tau using natural logarithms.

Physical Meaning of the Time Constant
  • τ=RC\tau = RC represents the time required for current or charge to decay to 1/e≈36.8%1/e \approx 36.8\% of its initial value, not the time to reach zero.

  • Never equate the zero-current time of a linear extrapolation to RCRC.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the exponential ratio: I1I2=18.0 μA4.20 μA≈4.286=eΔt/τ\frac{I_1}{I_2} = \frac{18.0\text{ }\mu\text{A}}{4.20\text{ }\mu\text{A}} \approx 4.286 = e^{\Delta t / \tau}.

  2. Take the natural logarithm: ln⁡(4.286)≈1.455=Δtτ\ln(4.286) \approx 1.455 = \frac{\Delta t}{\tau}.

  3. Find τ\tau using the elapsed interval and solve for capacitance: C=τR=37.4 μFC = \frac{\tau}{R} = 37.4\text{ }\mu\text{F}.

  4. Extrapolate back exponentially to t=0t = 0: I0=I1et1/τ≈43.64 μAI_0 = I_1 e^{t_1/\tau} \approx 43.64\text{ }\mu\text{A}.

  5. Apply Ohm's law to find the initial voltage: E=I0R≈9.60 V\mathcal{E} = I_0 R \approx 9.60\text{ V}.

Final answer

(a) C=37.4 μFC = 37.4\text{ }\mu\text{F}; (b) E=9.60 V\mathcal{E} = 9.60\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the derivation of the RCRC discharge equation from Kirchhoff's loop rule: qC+IR=0  ⟹  I(t)=I0e−t/RC\frac{q}{C} + IR = 0 \implies I(t) = I_0 e^{-t/RC}.

  • Practice solving exponential ratio equations using logarithms to isolate time constants.

OverviewACEpath Teacher's Diagnosis

02 A student inverts the ratio in the exponent when taking the natural logarithm, using ln(I₂ / I₁) = (t₂ - t₁) / τ without the negative sign.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I2I1=e−(t2−t1R⋅C)  ⟹  ln⁡(4.2018.0)=12.00−4.50220000⋅C  ⟹  −1.4586=7.50220000⋅C  ⟹  C=−2.34×10−5 F  ⟹  C=23.4 μF\frac{I_2}{I_1} = e^{-\left(\frac{t_2 - t_1}{R \cdot C}\right)} \implies \ln\left(\frac{4.20}{18.0}\right) = \frac{12.00 - 4.50}{220000 \cdot C} \implies -1.4586 = \frac{7.50}{220000 \cdot C} \implies C = -2.34 \times 10^{-5}\text{ F} \implies C = 23.4\text{ }\mu\text{F}

    Correct

    ln⁡(I2I1)=−t2−t1RC  ⟹  ln⁡(4.2018.0)=−12.00−4.50220000⋅C  ⟹  C≈2.34×10−5 F=23.4 μF\ln\left(\frac{I_2}{I_1}\right) = -\frac{t_2 - t_1}{RC} \implies \ln\left(\frac{4.20}{18.0}\right) = -\frac{12.00 - 4.50}{220000 \cdot C} \implies C \approx 2.34 \times 10^{-5}\text{ F} = 23.4\text{ }\mu\text{F}

    You dropped the negative sign on the right-hand side when taking the natural logarithm of both sides. Because I2<I1I_2 < I_1, ln⁡(I2/I1)\ln(I_2/I_1) is negative, so dropping the minus sign made your calculated capacitance negative (−2.34×10−5 F-2.34 \times 10^{-5}\text{ F}), which you then artificially forced to be positive.

  2. Step 2

    I0=I1⋅e−(t1τ)=18.0×10−6⋅e−(4.505.14)=7.51 μAI_0 = I_1 \cdot e^{-\left(\frac{t_1}{\tau}\right)} = 18.0 \times 10^{-6} \cdot e^{-\left(\frac{4.50}{5.14}\right)} = 7.51\text{ }\mu\text{A}

    Correct

    I1=I0e−t1/τ  ⟹  I0=I1e+t1/τ=(18.0 μA)⋅e4.50/5.15≈43.6 μAI_1 = I_0 e^{-t_1/\tau} \implies I_0 = I_1 e^{+t_1/\tau} = (18.0\text{ }\mu\text{A}) \cdot e^{4.50/5.15} \approx 43.6\text{ }\mu\text{A}

    You multiplied by e−t1/τe^{-t_1/\tau} instead of dividing by it. During capacitor discharge, the current decays over time, so the initial current I0I_0 at t=0t = 0 must be larger than I(4.50 s)=18.0 μAI(4.50\text{ s}) = 18.0\text{ }\mu\text{A}, not smaller.

  3. Step 3

    E=I0R=(7.51×10−6)(220000)=1.65 V\mathcal{E} = I_0 R = (7.51 \times 10^{-6})(220000) = 1.65\text{ V}

    Correct

    E=I0R=(43.64×10−6 A)(220000 Ω)≈9.60 V\mathcal{E} = I_0 R = (43.64 \times 10^{-6}\text{ A})(220000\text{ }\Omega) \approx 9.60\text{ V}

    Your formula E=I0R\mathcal{E} = I_0 R is correct, but the calculated voltage is wrong because it uses the incorrect value of I0I_0 from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the exponential decay equation for current during capacitor discharge.

You correctly used the time difference Δt=t2−t1=7.50 s\Delta t = t_2 - t_1 = 7.50\text{ s} between the two measurement points.

You correctly related the initial current and resistance to find the initial voltage using Ohm's law.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign and Inversion Error in Exponential Decay

You dropped the minus sign from −t2−t1RC-\frac{t_2 - t_1}{RC} when applying the natural logarithm, and you wrote I0=I1e−t1/τI_0 = I_1 e^{-t_1/\tau} instead of I0=I1e+t1/τI_0 = I_1 e^{+t_1/\tau}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You are losing track of signs when solving exponential equations ln⁡(e−x)=−x\ln(e^{-x}) = -x and reversing whether an exponential factor should grow or decay when solving backward in time.

REASONING PATH
Your ACEpath teacher’s suggested approach
Logarithm of Exponential with Negative Exponent
  • ln⁡(e−u)=−u\ln\left(e^{-u}\right) = -u, not +u+u.

  • Keep the negative sign explicitly on the exponent side, or invert the ratio so both sides are positive: ln⁡(I1/I2)=(t2−t1)/τ\ln(I_1 / I_2) = (t_2 - t_1)/\tau.

Physical Sanity Check for Extrapolating to $t = 0$
  • In discharging circuits, current decreases monotonically: I0>I(t)I_0 > I(t) for all t>0t > 0.

  • When solving I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau} for I0I_0, isolate I0=I(t)e+t/τI_0 = I(t) e^{+t/\tau} and verify that I0>I(t)I_0 > I(t).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Solve for the initial current: I0=I1et1/τ=(18.0 μA)e4.50 s/5.153 s≈18.0×2.424=43.64 μAI_0 = I_1 e^{t_1/\tau} = (18.0\text{ }\mu\text{A}) e^{4.50\text{ s} / 5.153\text{ s}} \approx 18.0 \times 2.424 = 43.64\text{ }\mu\text{A}.

  2. Calculate the initial potential: E=I0R=(43.64×10−6 A)(2.20×105 Ω)≈9.60 V\mathcal{E} = I_0 R = (43.64 \times 10^{-6}\text{ A})(2.20 \times 10^5\text{ }\Omega) \approx 9.60\text{ V}.

Final answer

(a) C=23.4 μFC = 23.4\text{ }\mu\text{F} (or 37.4 μF37.4\text{ }\mu\text{F} if referenced to total elapsed time 12.00 s12.00\text{ s}); (b) E=9.60 V\mathcal{E} = 9.60\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out ln⁡(Iearlier/Ilater)=Δt/τ\ln(I_{\text{earlier}} / I_{\text{later}}) = \Delta t / \tau to keep both sides positive and avoid sign drops.

  • Always perform a physical sanity check on initial values: in a discharging capacitor, I0I_0 must always exceed any later current.

OverviewACEpath Teacher's Diagnosis

03 A student forgets to convert resistor units from kΩ to Ω, using R = 220 instead of 220000 Ω, leading to an answer that is three orders of magnitude too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ln⁡(I1I2)=t2−t1R⋅C  ⟹  ln⁡(18.04.20)=12.00−4.50220⋅C  ⟹  1.4586=7.50220⋅C  ⟹  C=7.50220⋅1.4586=0.0234 F=23.4 mF\ln\left(\frac{I_1}{I_2}\right) = \frac{t_2 - t_1}{R \cdot C} \implies \ln\left(\frac{18.0}{4.20}\right) = \frac{12.00 - 4.50}{220 \cdot C} \implies 1.4586 = \frac{7.50}{220 \cdot C} \implies C = \frac{7.50}{220 \cdot 1.4586} = 0.0234\text{ F} = 23.4\text{ mF}

    Correct

    C=t2−t1Rln⁡(I1/I2)=7.50 s(220×103 Ω)(1.455)≈2.34×10−5 F=23.4 μFC = \frac{t_2 - t_1}{R \ln(I_1 / I_2)} = \frac{7.50\text{ s}}{(220 \times 10^3\text{ }\Omega)(1.455)} \approx 2.34 \times 10^{-5}\text{ F} = 23.4\text{ }\mu\text{F}

    You correctly formulated the logarithmic ratio of currents across the elapsed time interval Δt=7.50 s\Delta t = 7.50\text{ s}. However, you substituted R=220R = 220 instead of converting 220 kΩ220\text{ k}\Omega to 220×103 Ω220 \times 10^3\text{ }\Omega, resulting in a capacitance that is off by a factor of 10310^3.

  2. Step 2

    τ=R⋅C=220⋅0.0234=5.148 s  ⟹  I0=I1⋅et1/τ=(18.0×10−6)⋅e4.50/5.148=4.32×10−5 A\tau = R \cdot C = 220 \cdot 0.0234 = 5.148\text{ s} \implies I_0 = I_1 \cdot e^{t_1/\tau} = (18.0 \times 10^{-6}) \cdot e^{4.50 / 5.148} = 4.32 \times 10^{-5}\text{ A}

  3. Step 3

    E=I0⋅R=(4.32×10−5)⋅220=0.00950 V=9.50 mV\mathcal{E} = I_0 \cdot R = (4.32 \times 10^{-5}) \cdot 220 = 0.00950\text{ V} = 9.50\text{ mV}

    Correct

    E=I0R=(4.32×10−5 A)(220×103 Ω)≈9.50 V\mathcal{E} = I_0 R = (4.32 \times 10^{-5}\text{ A})(220 \times 10^3\text{ }\Omega) \approx 9.50\text{ V}

    You correctly applied Ohm's law to relate initial voltage to initial current, but you again substituted R=220R = 220 instead of 220×103 Ω220 \times 10^3\text{ }\Omega, yielding millivolts instead of volts.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the exponential decay equation for capacitor discharge.

You accurately evaluated the elapsed time difference Δt=12.00 s−4.50 s=7.50 s\Delta t = 12.00\text{ s} - 4.50\text{ s} = 7.50\text{ s}.

You correctly projected backward in time from t1=4.50 st_1 = 4.50\text{ s} to find the initial discharge current I0I_0.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated resistance values given with metric prefixes (kilo-ohms) as base SI units (ohms) during algebraic substitutions, omitting the factor of 10310^3.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert Metric Prefixes Before Calculating
  • Base SI units are required in standard circuit formulas: 1 kΩ=103 Ω1\text{ k}\Omega = 10^3\text{ }\Omega, 1 μF=10−6 F1\text{ }\mu\text{F} = 10^{-6}\text{ F}, and 1 μA=10−6 A1\text{ }\mu\text{A} = 10^{-6}\text{ A}.

  • Always rewrite known quantities in scientific notation with base SI units before substituting them into algebraic expressions.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute R=220 kΩ=2.20×105 ΩR = 220\text{ k}\Omega = 2.20 \times 10^5\text{ }\Omega into the capacitance expression: C=7.50 s(2.20×105 Ω)(1.455)≈23.4 μFC = \frac{7.50\text{ s}}{(2.20 \times 10^5\text{ }\Omega)(1.455)} \approx 23.4\text{ }\mu\text{F}.

  2. Recalculate the initial voltage using base SI units: E=I0R=(4.32×10−5 A)(2.20×105 Ω)≈9.50 V\mathcal{E} = I_0 R = (4.32 \times 10^{-5}\text{ A})(2.20 \times 10^5\text{ }\Omega) \approx 9.50\text{ V}.

Final answer

(a) C=23.4 μFC = 23.4\text{ }\mu\text{F}; (b) E=9.50 V\mathcal{E} = 9.50\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out every given parameter with its unit in full scientific notation before starting calculations.

  • Check that practical circuit values fall in reasonable ranges: capacitors in timing circuits are typically on the order of microfarads (μF\mu\text{F}), not millifarads (mF\text{mF}).

Lock it in

Similar question

01

A capacitor discharges through a 100 kΩ100\text{ k}\Omega resistor. If the current is 50 μA50\text{ }\mu\text{A} at t=0t = 0 and drops to 18.4 μA18.4\text{ }\mu\text{A} at t=2.0 st = 2.0\text{ s}, find the capacitance CC.

Answer

Using I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau}, 18.450=e−2.0/τ  ⟹  ln⁡(0.368)≈−1.0  ⟹  τ=2.0 s\frac{18.4}{50} = e^{-2.0/\tau} \implies \ln(0.368) \approx -1.0 \implies \tau = 2.0\text{ s}. Then C=τR=2.0 s100×103 Ω=20 μFC = \frac{\tau}{R} = \frac{2.0\text{ s}}{100 \times 10^3\text{ }\Omega} = 20\text{ }\mu\text{F}.

02

In a discharging RCRC circuit, the current drops from 24.0 mA24.0\text{ mA} at t=1.0 st = 1.0\text{ s} to 6.0 mA6.0\text{ mA} at t=5.0 st = 5.0\text{ s}. Determine the time constant τ\tau and the initial current I0I_0 at t=0t = 0.

Answer

I1I2=24.06.0=4=e(5.0−1.0)/τ  ⟹  ln⁡(4)=4.0τ  ⟹  τ=4.0ln⁡(4)≈2.89 s\frac{I_1}{I_2} = \frac{24.0}{6.0} = 4 = e^{(5.0 - 1.0)/\tau} \implies \ln(4) = \frac{4.0}{\tau} \implies \tau = \frac{4.0}{\ln(4)} \approx 2.89\text{ s}. Then I0=I1et1/τ=24.0⋅e1.0/2.89≈33.9 mAI_0 = I_1 e^{t_1/\tau} = 24.0 \cdot e^{1.0/2.89} \approx 33.9\text{ mA}.

03

A capacitor charged to E=12.0 V\mathcal{E} = 12.0\text{ V} discharges through an unknown resistor RR. At t=3.0 st = 3.0\text{ s}, the resistor current is 15.0 μA15.0\text{ }\mu\text{A}, and at t=9.0 st = 9.0\text{ s}, it is 5.0 μA5.0\text{ }\mu\text{A}. Find both RR and CC.

Answer

Δt=6.0 s\Delta t = 6.0\text{ s}, I1I2=3=e6.0/τ  ⟹  τ=6.0ln⁡(3)≈5.46 s\frac{I_1}{I_2} = 3 = e^{6.0/\tau} \implies \tau = \frac{6.0}{\ln(3)} \approx 5.46\text{ s}. Initial current I0=15.0⋅e3.0/5.46≈26.0 μAI_0 = 15.0 \cdot e^{3.0/5.46} \approx 26.0\text{ }\mu\text{A}. Resistor R=EI0=12.0 V26.0 μA≈462 kΩR = \frac{\mathcal{E}}{I_0} = \frac{12.0\text{ V}}{26.0\text{ }\mu\text{A}} \approx 462\text{ k}\Omega. Capacitance C=τR=5.46 s462×103 Ω≈11.8 μFC = \frac{\tau}{R} = \frac{5.46\text{ s}}{462 \times 10^3\text{ }\Omega} \approx 11.8\text{ }\mu\text{F}.

Loading workspace…