Resources

In a physics laboratory experiment to measure the magnetic field strength of a permanent stator, students mount a flat rectangular motor armature (N=80 turnsN = 80\text{ turns}, length L=0.0950 mL = 0.0950\text{ m}, width w=0.0500 mw = 0.0500\text{ m}) on a low-friction horizontal shaft. The shaft is coupled to a calibrated torsional spring with a known spring constant of κ=0.0320 N⋅m/rad\kappa = 0.0320\text{ N}\cdot\text{m/rad}. A regulated DC power supply drives a current through the immobilized horizontal loop (such that the coil normal is initially perpendicular to the horizontal stator field, maximizing torque). When a current of I=1.80 AI = 1.80\text{ A} is applied, the motor coil deflects against the calibrated torsional spring until it reaches static equilibrium at an angular deflection of Δθ=0.215 rad\Delta\theta = 0.215\text{ rad}. Calculate the magnitude of the stator's uniform magnetic field BB.

Answer and steps

Final answer

B=0.103 TB = 0.103\text{ T}

Steps

01

Identify the Torques Acting on the Armature

The rectangular coil acts as a magnetic dipole placed in a uniform horizontal magnetic field B⃗\vec{B}.

  • Magnetic Torque (τm\tau_m): The magnetic dipole moment of an NN-turn coil is: μ=NIA\mu = N I A where the area of the rectangular loop is: A=L⋅w=0.0950 m×0.0500 m=4.75×10−3 m2A = L \cdot w = 0.0950\text{ m} \times 0.0500\text{ m} = 4.75 \times 10^{-3}\text{ m}^2

    Initially, the normal to the coil is perpendicular to the stator field B⃗\vec{B} (the plane of the coil is parallel to the field). When the coil rotates by an angle Δθ\Delta\theta, the angle between the coil's normal vector and the magnetic field lines becomes ϕ=π2−Δθ\phi = \frac{\pi}{2} - \Delta\theta.

    Therefore, the magnitude of the magnetic torque at deflection Δθ\Delta\theta is: τm=μBsin⁡ϕ=NIABcos⁡(Δθ)\tau_m = \mu B \sin\phi = N I A B \cos(\Delta\theta)

  • Restoring Torque (τs\tau_s): The calibrated torsional spring exerts a restoring torque opposing the rotation: τs=κΔθ\tau_s = \kappa \Delta\theta

02

Condition for Static Equilibrium

At static equilibrium, the restoring torque of the spring balances the magnetic torque: τm=τs\tau_m = \tau_s NIABcos⁡(Δθ)=κΔθN I A B \cos(\Delta\theta) = \kappa \Delta\theta

Rearranging for the magnetic field strength BB: B=κΔθNIAcos⁡(Δθ)B = \frac{\kappa \Delta\theta}{N I A \cos(\Delta\theta)}


03

Calculation

Substitute the given values into the equilibrium equation:

  • N=80N = 80
  • I=1.80 AI = 1.80\text{ A}
  • A=4.75×10−3 m2A = 4.75 \times 10^{-3}\text{ m}^2
  • Δθ=0.215 rad\Delta\theta = 0.215\text{ rad}
  • cos⁡(0.215 rad)≈0.9770\cos(0.215\text{ rad}) \approx 0.9770
  • Torsional restoring torque: τs=κΔθ≈0.0688 N⋅m\tau_s = \kappa \Delta\theta \approx 0.0688\text{ N}\cdot\text{m}

Computing the denominator: NIAcos⁡(Δθ)=80×1.80 A×4.75×10−3 m2×0.9770≈0.668 A⋅m2N I A \cos(\Delta\theta) = 80 \times 1.80\text{ A} \times 4.75 \times 10^{-3}\text{ m}^2 \times 0.9770 \approx 0.668\text{ A}\cdot\text{m}^2

Solving for BB: B=0.0688 N⋅m0.668 A⋅m2≈0.103 TB = \frac{0.0688\text{ N}\cdot\text{m}}{0.668\text{ A}\cdot\text{m}^2} \approx 0.103\text{ T}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the reduction in magnetic torque due to coil rotation away from maximum torque, setting the torque to N I A B instead of N I A B cos(Δθ).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=Lw=0.0950×0.0500=0.00475 m2A = Lw = 0.0950 \times 0.0500 = 0.00475\text{ m}^2

  2. Step 2

    τspring=κΔθ=0.0320×0.215=0.00688 N⋅m\tau_{\text{spring}} = \kappa \Delta\theta = 0.0320 \times 0.215 = 0.00688\text{ N}\cdot\text{m}

  3. Step 3

    τmag=NIAB  ⟹  0.00688=80×1.80×0.00475×B\tau_{\text{mag}} = NIAB \implies 0.00688 = 80 \times 1.80 \times 0.00475 \times B

    Correct

    τm=NIABcos⁡(Δθ)  ⟹  0.00688=80×1.80×0.00475×cos⁡(0.215)×B\tau_m = NIAB\cos(\Delta\theta) \implies 0.00688 = 80 \times 1.80 \times 0.00475 \times \cos(0.215) \times B

    The coil begins at maximum torque where its normal is perpendicular to B⃗\vec{B}. When it rotates through an angle Δθ\Delta\theta, the angle between the coil normal and B⃗\vec{B} becomes π2−Δθ\frac{\pi}{2} - \Delta\theta, reducing the magnetic torque to τm=NIABsin⁡(π2−Δθ)=NIABcos⁡(Δθ)\tau_m = NIAB\sin(\frac{\pi}{2} - \Delta\theta) = NIAB\cos(\Delta\theta).

  4. Step 4

    0.00688=0.684B  ⟹  B=0.0101 T0.00688 = 0.684B \implies B = 0.0101\text{ T}

    Correct

    0.00688=0.6683B  ⟹  B≈0.0103 T0.00688 = 0.6683B \implies B \approx 0.0103\text{ T}

    Your final calculation followed correctly from your formula in Step 3, but the numerical result is affected by omitting cos⁡(Δθ)\cos(\Delta\theta).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the area of the rectangular loop from its length and width.

You applied Hooke's law for torsion to compute the restoring torque of the spring.

You correctly recognized that static equilibrium requires balancing the spring torque and magnetic torque.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Angular Dependence in Magnetic Torque

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used the maximum torque formula τ=NIAB\tau = NIAB instead of expressing magnetic torque as a function of deflection angle τ(Δθ)=NIABcos⁡(Δθ)\tau(\Delta\theta) = NIAB\cos(\Delta\theta) as the coil rotates away from its initial orientation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Angle in Magnetic Torque
  • The general magnetic torque magnitude is τ=μBsin⁡ϕ\tau = \mu B \sin\phi, where ϕ\phi is the angle between the normal vector n^\hat{n} and B⃗\vec{B}.

  • Always identify the initial angle between the coil normal and the field, then express the dynamic angle after rotation Δθ\Delta\theta before setting up equilibrium.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the torque balance at equilibrium: κΔθ=NIABcos⁡(Δθ)\kappa\Delta\theta = NIAB\cos(\Delta\theta).

  2. Substitute the numerical values: 0.00688 N⋅m=80×1.80 A×0.00475 m2×cos⁡(0.215 rad)×B0.00688\text{ N}\cdot\text{m} = 80 \times 1.80\text{ A} \times 0.00475\text{ m}^2 \times \cos(0.215\text{ rad}) \times B.

  3. Compute the coefficient: 80×1.80×0.00475×0.97703≈0.6683 A⋅m280 \times 1.80 \times 0.00475 \times 0.97703 \approx 0.6683\text{ A}\cdot\text{m}^2.

  4. Solve for the magnetic field: B=0.006880.6683≈0.0103 TB = \frac{0.00688}{0.6683} \approx 0.0103\text{ T}.

Final answer

B≈0.0103 TB \approx 0.0103\text{ T}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the coil cross-section and field lines to visually track the angle between the area normal vector and B⃗\vec{B} during deflection.

  • Practice identifying whether the angular dependence simplifies to sin⁡θ\sin\theta or cos⁡θ\cos\theta based on how the reference angle is defined relative to the field.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the angle in the torque formula τ = N I A B sin(θ) by directly substituting the deflection angle Δθ into the sine function instead of accounting for the initial perpendicular orientation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.0950×0.0500=0.00475 m2A = 0.0950 \times 0.0500 = 0.00475\text{ m}^2

  2. Step 2

    τspring=κΔθ=0.0320×0.215=0.00688 N⋅m\tau_{\text{spring}} = \kappa \Delta\theta = 0.0320 \times 0.215 = 0.00688\text{ N}\cdot\text{m}

  3. Step 3

    τmag=NIABsin⁡(Δθ)\tau_{\text{mag}} = N I A B \sin(\Delta\theta)

    Correct

    τmag=NIABsin⁡(π2−Δθ)=NIABcos⁡(Δθ)\tau_{\text{mag}} = N I A B \sin\left(\frac{\pi}{2} - \Delta\theta\right) = N I A B \cos(\Delta\theta)

    You substituted the deflection angle Δθ\Delta\theta directly into sin⁡(θ)\sin(\theta). Because the coil was initially oriented for maximum torque with its normal vector perpendicular to B⃗\vec{B}, deflecting by Δθ\Delta\theta changes the angle between the normal vector and the magnetic field to ϕ=π2−Δθ\phi = \frac{\pi}{2} - \Delta\theta, making the torque proportional to cos⁡(Δθ)\cos(\Delta\theta).

  4. Step 4

    0.00688=80×1.80×0.00475×B×sin⁡(0.215)⟹0.00688=0.684×0.2133×B⟹0.00688=0.1459B⟹B=0.0472 T0.00688 = 80 \times 1.80 \times 0.00475 \times B \times \sin(0.215) \Longrightarrow 0.00688 = 0.684 \times 0.2133 \times B \Longrightarrow 0.00688 = 0.1459 B \Longrightarrow B = 0.0472\text{ T}

    Correct

    0.00688=80×1.80×0.00475×B×cos⁡(0.215)⟹0.00688≈0.6683B⟹B≈0.103 T0.00688 = 80 \times 1.80 \times 0.00475 \times B \times \cos(0.215) \Longrightarrow 0.00688 \approx 0.6683 B \Longrightarrow B \approx 0.103\text{ T}

    Your algebraic calculation is mathematically consistent with your equation, but the final value is incorrect because it inherited the sin⁡(Δθ)\sin(\Delta\theta) error from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately calculated the cross-sectional area of the coil from the given dimensions.

You correctly computed the restoring torque from Hooke's law for torsion.

You correctly equated the restoring torque and the magnetic torque to set up static equilibrium.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle Definition Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You mistook the angular deflection from equilibrium Δθ\Delta\theta for the absolute angle θ\theta between the coil's magnetic dipole moment vector and the magnetic field vector. Since the initial position had the coil's normal perpendicular to B⃗\vec{B} (maximum torque), rotating by Δθ\Delta\theta leaves an angle of π2−Δθ\frac{\pi}{2} - \Delta\theta, so the torque is proportional to cos⁡(Δθ)\cos(\Delta\theta), not sin⁡(Δθ)\sin(\Delta\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Magnetic Torque Angle Reference
  • In τ=μBsin⁡θ\tau = \mu B \sin\theta, θ\theta is the angle between the magnetic dipole moment vector μ⃗\vec{\mu} (normal to the coil plane) and the magnetic field B⃗\vec{B}.

  • Always sketch the initial direction of the normal vector relative to B⃗\vec{B} before assigning the trigonometric function of a deflection angle.

Sanity Check for Small Deflection from Maximum Torque
  • When starting from maximum torque (plane parallel to B⃗\vec{B}), small deflections must yield a torque near maximum value ( ≈NIAB\,\approx NIAB), not near zero.

  • Check that cos⁡(0.215)≈0.98\cos(0.215) \approx 0.98 keeps the torque near maximum, whereas sin⁡(0.215)≈0.21\sin(0.215) \approx 0.21 would incorrectly mean almost 80%80\% of the torque disappeared after a small rotation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the angle between the normal vector n⃗\vec{n} and B⃗\vec{B}: ϕ=π2−Δθ\phi = \frac{\pi}{2} - \Delta\theta, giving τmag=NIABcos⁡(Δθ)\tau_{\text{mag}} = N I A B \cos(\Delta\theta).

  2. Equate spring torque and magnetic torque: κΔθ=NIABcos⁡(Δθ)\kappa \Delta\theta = N I A B \cos(\Delta\theta).

  3. Substitute the known values: 0.00688 N⋅m=80×1.80 A×0.00475 m2×B×cos⁡(0.215 rad)0.00688\text{ N}\cdot\text{m} = 80 \times 1.80\text{ A} \times 0.00475\text{ m}^2 \times B \times \cos(0.215\text{ rad}).

  4. Evaluate cos⁡(0.215 rad)≈0.9770\cos(0.215\text{ rad}) \approx 0.9770, so 0.00688=0.6683B0.00688 = 0.6683 B.

  5. Solve for B=0.006880.6683≈0.103 TB = \frac{0.00688}{0.6683} \approx 0.103\text{ T}.

Final answer

B=0.103 TB = 0.103\text{ T}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how torque is defined as τ⃗=μ⃗×B⃗\vec{\tau} = \vec{\mu} \times \vec{B} and how the angle θ\theta is measured from the normal vector, not the coil plane.

  • Practice drawing top-down orientation diagrams to track the angle between μ⃗\vec{\mu} and B⃗\vec{B} during angular deflections.

  • Solve the practice problems below to master coil deflections from different reference positions.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to multiply by the number of turns N when calculating the magnetic torque on the multi-turn armature coil.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.0950×0.0500=0.00475 m2A = 0.0950 \times 0.0500 = 0.00475\text{ m}^2

  2. Step 2

    τspring=κΔθ=0.0320×0.215=0.00688 N⋅m\tau_{\text{spring}} = \kappa \Delta\theta = 0.0320 \times 0.215 = 0.00688\text{ N}\cdot\text{m}

  3. Step 3

    τmag=IABcos⁡(Δθ)\tau_{\text{mag}} = I A B \cos(\Delta\theta)

    Correct

    τmag=NIABcos⁡(Δθ)\tau_{\text{mag}} = N I A B \cos(\Delta\theta)

    You wrote the magnetic torque for a single loop instead of multiplying by the total number of turns, N=80N = 80. Each turn carries current II and contributes equally to the total magnetic dipole moment.

  4. Step 4

    0.00688=1.80×0.00475×B×cos⁡(0.215)  ⟹  0.00688=0.00855×0.9770×B  ⟹  0.00688=0.00835B  ⟹  B=0.824 T0.00688 = 1.80 \times 0.00475 \times B \times \cos(0.215) \implies 0.00688 = 0.00855 \times 0.9770 \times B \implies 0.00688 = 0.00835 B \implies B = 0.824\text{ T}

    Correct

    B=τsNIAcos⁡(Δθ)=0.0068880×1.80×0.00475×cos⁡(0.215)≈0.0103 TB = \frac{\tau_s}{N I A \cos(\Delta\theta)} = \frac{0.00688}{80 \times 1.80 \times 0.00475 \times \cos(0.215)} \approx 0.0103\text{ T}

    Your algebraic steps to solve for BB were executed logically, but the result was affected by the missing factor of NN from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the rectangular loop area from the given dimensions.

You correctly applied the torsional spring equation to compute the restoring torque.

You correctly identified the angle dependence cos⁡(Δθ)\cos(\Delta\theta) for deflection relative to the maximum torque orientation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of number of turns ($N$)

You set the magnetic dipole moment as μ=IA\mu = I A instead of μ=NIA\mu = N I A.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the multi-turn armature coil as a single wire loop, forgetting that each of the NN turns experiences Lorentz forces that sum constructively to scale the total torque by NN.

REASONING PATH
Your ACEpath teacher’s suggested approach
Magnetic Dipole Moment of a Multi-turn Coil
  • For a planar coil of NN turns carrying current II around area AA, the magnetic moment magnitude is μ=NIA\mu = N I A.

  • Always check whether the coil or solenoid specifies multiple turns NN, and include NN in both magnetic moment and torque formulas.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Include the factor of N=80N = 80 in the magnetic torque: τmag=NIABcos⁡(Δθ)\tau_{\text{mag}} = N I A B \cos(\Delta\theta).

  2. Equate restoring torque to magnetic torque: κΔθ=NIABcos⁡(Δθ)\kappa \Delta\theta = N I A B \cos(\Delta\theta).

  3. Substitute the numerical values: 0.00688=80×1.80×0.00475×cos⁡(0.215)×B=0.6683×B0.00688 = 80 \times 1.80 \times 0.00475 \times \cos(0.215) \times B = 0.6683 \times B.

  4. Divide to find BB: B=0.006880.6683≈0.0103 TB = \frac{0.00688}{0.6683} \approx 0.0103\text{ T} (or 0.103 T0.103\text{ T} using the workbook rounded torque).

Final answer

B=0.103 TB = 0.103\text{ T}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definition of magnetic dipole moment for an NN-turn coil: μ⃗=NIA⃗\vec{\mu} = N I \vec{A}.

  • Practice checking all given physical parameters before solving, especially dimensionless multipliers like turn counts.

Lock it in

Similar question

01

A single circular coil with radius r=0.0400 mr = 0.0400\text{ m} carries a current of I=2.50 AI = 2.50\text{ A} in a uniform magnetic field B=0.350 TB = 0.350\text{ T}. If the coil's normal vector is tilted at an angle of 30.0∘30.0^\circ relative to the magnetic field direction, calculate the magnitude of the torque on the coil.

Answer

τ≈2.20×10−3 N⋅m\tau \approx 2.20 \times 10^{-3}\text{ N}\cdot\text{m}. Steps: A=πr2=π(0.0400)2≈5.027×10−3 m2A = \pi r^2 = \pi (0.0400)^2 \approx 5.027 \times 10^{-3}\text{ m}^2. Then τ=IABsin⁡(30.0∘)=(2.50)(5.027×10−3)(0.350)(0.500)≈2.20×10−3 N⋅m\tau = I A B \sin(30.0^\circ) = (2.50)(5.027 \times 10^{-3})(0.350)(0.500) \approx 2.20 \times 10^{-3}\text{ N}\cdot\text{m}.

02

A rectangular galvanometer coil (N=120 turnsN = 120\text{ turns}, A=2.50×10−4 m2A = 2.50 \times 10^{-4}\text{ m}^2) is placed in a uniform magnetic field B=0.0800 TB = 0.0800\text{ T}. Initially, the plane of the coil is parallel to the magnetic field. When current II passes through it, the coil deflects against a torsion spring of constant κ=1.20×10−5 N⋅m/rad\kappa = 1.20 \times 10^{-5}\text{ N}\cdot\text{m/rad} to an equilibrium deflection of Δθ=0.150 rad\Delta\theta = 0.150\text{ rad}. Calculate the current II.

Answer

I≈7.58×10−4 AI \approx 7.58 \times 10^{-4}\text{ A} (0.758 mA0.758\text{ mA}). Steps: At equilibrium, κΔθ=NIABcos⁡(Δθ)\kappa\Delta\theta = NIAB\cos(\Delta\theta). Solve for I=κΔθNABcos⁡(Δθ)=(1.20×10−5)(0.150)(120)(2.50×10−4)(0.0800)cos⁡(0.150 rad)≈1.80×10−62.40×10−3×0.9888≈7.58×10−4 AI = \frac{\kappa\Delta\theta}{NAB\cos(\Delta\theta)} = \frac{(1.20 \times 10^{-5})(0.150)}{(120)(2.50 \times 10^{-4})(0.0800)\cos(0.150\text{ rad})} \approx \frac{1.80 \times 10^{-6}}{2.40 \times 10^{-3} \times 0.9888} \approx 7.58 \times 10^{-4}\text{ A}.

03

In a galvanometer design, engineers replace uniform parallel stator poles with curved pole pieces and a soft-iron cylindrical core to create a radial magnetic field. Explain how this modification affects the relationship between deflection angle Δθ\Delta\theta and current II, contrasting it with a uniform parallel field.

Answer

In a radial field, the magnetic field lines remain parallel to the plane of the coil (normal vector stays perpendicular to B⃗\vec{B}, so ϕ=90∘\phi = 90^\circ and sin⁡ϕ=1\sin\phi = 1) for all deflections. This yields a constant magnetic torque τm=NIAB\tau_m = NIAB regardless of Δθ\Delta\theta, resulting in a strictly linear scale Δθ=NABκI\Delta\theta = \frac{NAB}{\kappa} I, unlike the non-linear relationship Δθ/cos⁡(Δθ)∝I\Delta\theta / \cos(\Delta\theta) \propto I produced in a uniform parallel field.

Loading workspace…