Resources

A multi-turn sensor coil has N=450N = 450 circular turns with cross-sectional diameter d=24.0 mmd = 24.0\text{ mm}. The coil is positioned perpendicular to an alternating magnetic field that changes linearly at a rate of ΔBΔt=175 mT/s\frac{\Delta B}{\Delta t} = 175\text{ mT/s}. The sensor coil is wired in series to a microammeter having an internal resistance of R=85.0 ΩR = 85.0\ \Omega (assume the coil wire resistance is negligible). Calculate the magnitude of the induced electromotive force E\mathcal{E} in millivolts (mV\text{mV}) and the magnitude of the resulting induced electric current II in microamperes (μA\mu\text{A}).

Answer and steps

Final answer

E=35.6 mV\mathcal{E} = 35.6\text{ mV}, I=419 μAI = 419\ \mu\text{A}

Steps

01

Calculate the Cross-Sectional Area of the Coil

The coil consists of circular turns of diameter d=24.0 mm=0.0240 md = 24.0\text{ mm} = 0.0240\text{ m}.

First, determine the radius rr: r=d2=0.0240 m2=0.0120 mr = \frac{d}{2} = \frac{0.0240\text{ m}}{2} = 0.0120\text{ m}

The cross-sectional area AA of a single circular loop is: A=πr2=π(0.0120 m)2≈4.524×10−4 m2A = \pi r^2 = \pi (0.0120\text{ m})^2 \approx 4.524 \times 10^{-4}\text{ m}^2


02

Determine the Induced Electromotive Force (E\mathcal{E})

According to Faraday's law of electromagnetic induction, the magnitude of the induced electromotive force in a coil of NN turns is equal to the rate of change of magnetic flux through the coil: E=N∣ΔΦBΔt∣\mathcal{E} = N \left| \frac{\Delta \Phi_B}{\Delta t} \right|

Because the coil plane is perpendicular to the magnetic field, the magnetic field vectors align with the normal vector of the coil area (θ=0∘\theta = 0^\circ). Thus, the magnetic flux through a single turn is ΦB=BAcos⁡(0∘)=BA\Phi_B = B A \cos(0^\circ) = B A.

Since the area AA remains constant over time, the rate of change of flux depends entirely on the changing magnetic field: ΔΦBΔt=AΔBΔt\frac{\Delta \Phi_B}{\Delta t} = A \frac{\Delta B}{\Delta t}

Given that the magnetic field changes at a rate of ΔBΔt=175 mT/s=0.175 T/s\frac{\Delta B}{\Delta t} = 175\text{ mT/s} = 0.175\text{ T/s} and the coil has N=450N = 450 turns: E=NAΔBΔt\mathcal{E} = N A \frac{\Delta B}{\Delta t} E=(450)⋅(4.524×10−4 m2)⋅(0.175 T/s)≈0.03563 V\mathcal{E} = (450) \cdot (4.524 \times 10^{-4}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 0.03563\text{ V}

Converting this value to millivolts (mV\text{mV}): E=0.03563 V×103 mV/V≈35.6 mV\mathcal{E} = 0.03563\text{ V} \times 10^3\text{ mV/V} \approx 35.6\text{ mV}

Common Pitfall: Always convert diameter to radius and ensure all metric prefixes (such as millimeters to meters, and milliteslas to teslas) are converted to standard SI base units before multiplying, to avoid scale errors by factors of 10310^3 or 10610^6.


03

Calculate the Induced Current (II)

Using Ohm's law, the current flowing through the closed circuit with total resistance R=85.0 ΩR = 85.0\ \Omega is: I=ERI = \frac{\mathcal{E}}{R}

Substitute the calculated electromotive force: I=0.03563 V85.0 Ω≈4.192×10−4 AI = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 4.192 \times 10^{-4}\text{ A}

Converting this value to microamperes (μA\mu\text{A}): I=4.192×10−4 A×106 μA/A≈419 μAI = 4.192 \times 10^{-4}\text{ A} \times 10^6\ \mu\text{A/A} \approx 419\ \mu\text{A}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the diameter directly instead of the radius in the area formula, overestimating the area and induced electromotive force by a factor of 4.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    d=24.0 mm=0.024 m  ⟹  A=π⋅d2=π⋅(0.024 m)2≈1.8096×10−3 m2d = 24.0\text{ mm} = 0.024\text{ m} \implies A = \pi \cdot d^2 = \pi \cdot (0.024\text{ m})^2 \approx 1.8096 \times 10^{-3}\text{ m}^2

    Correct

    r=d2=0.0120 m  ⟹  A=πr2=π(0.0120 m)2≈4.524×10−4 m2r = \frac{d}{2} = 0.0120\text{ m} \implies A = \pi r^2 = \pi (0.0120\text{ m})^2 \approx 4.524 \times 10^{-4}\text{ m}^2

    You converted millimeters to meters correctly, but you used the diameter dd directly in the formula A=πd2A = \pi d^2. The area of a circular loop is A=πr2=πd24A = \pi r^2 = \frac{\pi d^2}{4}.

  2. Step 2

    E=N⋅A⋅(ΔBΔt)=450⋅(1.8096×10−3 m2)⋅(0.175 T/s)≈0.1425 V=143 mVE = N \cdot A \cdot \left(\frac{\Delta B}{\Delta t}\right) = 450 \cdot (1.8096 \times 10^{-3}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 0.1425\text{ V} = 143\text{ mV}

    Correct

    E=N⋅A⋅(ΔBΔt)=450⋅(4.524×10−4 m2)⋅(0.175 T/s)≈0.03563 V≈35.6 mV\mathcal{E} = N \cdot A \cdot \left(\frac{\Delta B}{\Delta t}\right) = 450 \cdot (4.524 \times 10^{-4}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 0.03563\text{ V} \approx 35.6\text{ mV}

    Your application of Faraday's law and your conversion from mT/s\text{mT/s} to T/s\text{T/s} were completely correct, but the calculated voltage inherited the factor of 44 error from your area.

  3. Step 3

    I=ER=0.1425 V85.0 Ω≈1.677×10−3 A=1680 μAI = \frac{E}{R} = \frac{0.1425\text{ V}}{85.0\ \Omega} \approx 1.677 \times 10^{-3}\text{ A} = 1680\ \mu\text{A}

    Correct

    I=ER=0.03563 V85.0 Ω≈4.192×10−4 A≈419 μAI = \frac{\mathcal{E}}{R} = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 4.192 \times 10^{-4}\text{ A} \approx 419\ \mu\text{A}

    Your use of Ohm's law and your final conversion to microamperes were correct, but the numerical current value inherited the upstream error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied Faraday's law of induction for an NN-turn coil.

You accurately converted all SI prefixes including milliteslas, millivolts, and microamperes.

You correctly used Ohm's law to link induced electromotive force to circuit current.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometric Formula Error

You substituted the diameter dd directly into πd2\pi d^2 instead of dividing by 22 to find the radius or using πd24\frac{\pi d^2}{4}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating diameter with radius in the area formula for a circle, resulting in an area overestimation by a factor of 22=42^2 = 4.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Diameter vs. Radius
  • A=πr2=14πd2A = \pi r^2 = \frac{1}{4}\pi d^2

  • Whenever a problem specifies a diameter, write down r=d/2r = d / 2 as your very first step before calculating area.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the loop radius: r=d2=0.0240 m2=0.0120 mr = \frac{d}{2} = \frac{0.0240\text{ m}}{2} = 0.0120\text{ m}.

  2. Recalculate the single-turn area: A=πr2=π(0.0120 m)2≈4.524×10−4 m2A = \pi r^2 = \pi (0.0120\text{ m})^2 \approx 4.524 \times 10^{-4}\text{ m}^2.

  3. Substitute into Faraday's law: E=NA(ΔBΔt)=450⋅(4.524×10−4 m2)⋅(0.175 T/s)≈35.6 mV\mathcal{E} = N A \left(\frac{\Delta B}{\Delta t}\right) = 450 \cdot (4.524 \times 10^{-4}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 35.6\text{ mV}.

  4. Apply Ohm's law: I=ER=0.03563 V85.0 Ω≈419 μAI = \frac{\mathcal{E}}{R} = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 419\ \mu\text{A}.

Final answer

E=35.6 mV\mathcal{E} = 35.6\text{ mV}, I=419 μAI = 419\ \mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice spotting given diameters and explicitly writing r=d/2r = d/2 before writing any formulas.

  • Check that your area formulas use radius squared, not diameter squared.

  • Solve the practice problems below to reinforce circular geometry inside electromagnetic induction calculations.

OverviewACEpath Teacher's Diagnosis

02 The student omits the number of turns N when calculating the induced electromotive force across the multi-turn coil.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=d2=12.0 mm=0.012 m⟹A=π⋅r2=π⋅(0.012 m)2≈4.524×10−4 m2r = \frac{d}{2} = 12.0\text{ mm} = 0.012\text{ m} \Longrightarrow A = \pi \cdot r^2 = \pi \cdot (0.012\text{ m})^2 \approx 4.524 \times 10^{-4}\text{ m}^2

  2. Step 2

    E=A⋅(ΔBΔt)=(4.524×10−4 m2)⋅(0.175 T/s)≈7.917×10−5 V=0.0792 mVE = A \cdot \left(\frac{\Delta B}{\Delta t}\right) = (4.524 \times 10^{-4}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 7.917 \times 10^{-5}\text{ V} = 0.0792\text{ mV}

    Correct

    E=NA(ΔBΔt)=(450)(4.524×10−4 m2)(0.175 T/s)≈0.03563 V=35.6 mV\mathcal{E} = N A \left(\frac{\Delta B}{\Delta t}\right) = (450)(4.524 \times 10^{-4}\text{ m}^2)(0.175\text{ T/s}) \approx 0.03563\text{ V} = 35.6\text{ mV}

    For a coil with NN turns, each turn encloses the changing flux, so the induced EMF is E=N∣ΔΦBΔt∣=NAΔBΔt\mathcal{E} = N |\frac{\Delta \Phi_B}{\Delta t}| = N A \frac{\Delta B}{\Delta t}. You omitted the factor N=450N = 450.

  3. Step 3

    I=ER=7.917×10−5 V85.0 Ω≈9.314×10−7 A=0.931 μAI = \frac{E}{R} = \frac{7.917 \times 10^{-5}\text{ V}}{85.0\ \Omega} \approx 9.314 \times 10^{-7}\text{ A} = 0.931\ \mu\text{A}

    Correct

    I=ER=0.03563 V85.0 Ω≈4.192×10−4 A=419 μAI = \frac{\mathcal{E}}{R} = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 4.192 \times 10^{-4}\text{ A} = 419\ \mu\text{A}

    You applied Ohm's law with the correct formula I=ERI = \frac{\mathcal{E}}{R}, but your numerical result was affected by the missing factor of NN from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly halved the diameter to find the radius and converted units to standard meters.

You computed the circular cross-sectional area accurately using A=πr2A = \pi r^2.

You correctly used Ohm's law I=ERI = \frac{\mathcal{E}}{R} to relate induced EMF to current.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of coil turns $N$ in Faraday's law

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the multi-turn coil as a single loop of wire rather than a series stack of NN loops, overlooking that the EMF induced in each turn adds constructively across the entire coil.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check loop count in Faraday's law
  • For an NN-turn tightly wound coil, the total induced electromotive force is E=N∣dΦBdt∣\mathcal{E} = N \left| \frac{d\Phi_B}{dt} \right|.

  • Always scan the problem statement for the number of turns NN before writing the flux derivative formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Include the N=450N = 450 turns in the EMF equation: E=NAΔBΔt=(450)(4.524×10−4 m2)(0.175 T/s)≈0.03563 V=35.6 mV\mathcal{E} = N A \frac{\Delta B}{\Delta t} = (450)(4.524 \times 10^{-4}\text{ m}^2)(0.175\text{ T/s}) \approx 0.03563\text{ V} = 35.6\text{ mV}.

  2. Substitute this total EMF into Ohm's law: I=ER=0.03563 V85.0 Ω≈4.192×10−4 A=419 μAI = \frac{\mathcal{E}}{R} = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 4.192 \times 10^{-4}\text{ A} = 419\ \mu\text{A}.

Final answer

E=35.6 mV\mathcal{E} = 35.6\text{ mV}, I=419 μAI = 419\ \mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review Faraday's law for coils: write E=−NΔΦΔt\mathcal{E} = -N \frac{\Delta \Phi}{\Delta t} as the starting equation every time.

  • Highlight the variable NN whenever a problem specifies a coil or solenoid to ensure it is not left out of the final calculation.

OverviewACEpath Teacher's Diagnosis

03 The student fails to convert the diameter from millimeters to meters, resulting in an area and induced EMF that are too large by a factor of 10⁶.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=24.0/2=12.0 mm  ⟹  A=π⋅r2=π⋅(12.0)2≈452.39 mm2r = 24.0 / 2 = 12.0\text{ mm} \implies A = \pi \cdot r^2 = \pi \cdot (12.0)^2 \approx 452.39\text{ mm}^2

  2. Step 2

    E=N⋅A⋅(ΔBΔt)=450⋅452.39⋅0.175≈35626 mV  ⟹  E=35.626 VE = N \cdot A \cdot \left(\frac{\Delta B}{\Delta t}\right) = 450 \cdot 452.39 \cdot 0.175 \approx 35626\text{ mV} \implies E = 35.626\text{ V}

    Correct

    E=NA(ΔBΔt)=450⋅(4.524×10−4 m2)⋅(0.175 T/s)≈0.03563 V=35.6 mV\mathcal{E} = N A \left(\frac{\Delta B}{\Delta t}\right) = 450 \cdot (4.524 \times 10^{-4}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 0.03563\text{ V} = 35.6\text{ mV}

    You substituted the area in mm2\text{mm}^2 instead of standard SI units (m2\text{m}^2). Because 1 mm2=10−6 m21\text{ mm}^2 = 10^{-6}\text{ m}^2, the raw product yielded microvolts (μV\mu\text{V}), but you labeled it as millivolts and converted it to 35.626 V35.626\text{ V}, making E\mathcal{E} 10310^3 times too large.

  3. Step 3

    I=E/R=35.626 V/85.0 Ω≈0.419 A=419000 μAI = E / R = 35.626\text{ V} / 85.0\ \Omega \approx 0.419\text{ A} = 419000\ \mu\text{A}

    Correct

    I=ER=0.03563 V85.0 Ω≈4.19×10−4 A=419 μAI = \frac{\mathcal{E}}{R} = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 4.19 \times 10^{-4}\text{ A} = 419\ \mu\text{A}

    You correctly applied Ohm's law I=E/RI = \mathcal{E}/R, but your result inherited the scale error from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly halved the diameter to find the radius of the coil.

You correctly identified Faraday's law of induction for a multi-turn coil.

You converted the rate of field change from mT/s\text{mT/s} to T/s\text{T/s} properly.

You correctly applied Ohm's law to relate induced voltage and current.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You did not convert linear dimensions or area into SI base units (meters and square meters) before multiplying in physical formulas, leading to an incorrect prefix assignment for the induced voltage.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Base Units in Electromagnetism
  • All geometric quantities must be converted to meters (m\text{m}) or square meters (m2\text{m}^2) before evaluating electromagnetic formulas: 1 mm=10−3 m  ⟹  1 mm2=10−6 m21\text{ mm} = 10^{-3}\text{ m} \implies 1\text{ mm}^2 = 10^{-6}\text{ m}^2.

  • Convert millimeters to meters at the very first step before calculating area.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the coil area to square meters: A=452.39 mm2×10−6 m2/mm2=4.524×10−4 m2A = 452.39\text{ mm}^2 \times 10^{-6}\text{ m}^2/\text{mm}^2 = 4.524 \times 10^{-4}\text{ m}^2.

  2. Calculate the induced EMF in standard SI units: E=450⋅(4.524×10−4 m2)⋅(0.175 T/s)≈0.03563 V\mathcal{E} = 450 \cdot (4.524 \times 10^{-4}\text{ m}^2) \cdot (0.175\text{ T/s}) \approx 0.03563\text{ V}.

  3. Express the EMF in millivolts: E=0.03563 V×103 mV/V≈35.6 mV\mathcal{E} = 0.03563\text{ V} \times 10^3\text{ mV/V} \approx 35.6\text{ mV}.

  4. Calculate the induced current using Ohm's law: I=ER=0.03563 V85.0 Ω≈4.192×10−4 A=419 μAI = \frac{\mathcal{E}}{R} = \frac{0.03563\text{ V}}{85.0\ \Omega} \approx 4.192 \times 10^{-4}\text{ A} = 419\ \mu\text{A}.

Final answer

E=35.6 mV\mathcal{E} = 35.6\text{ mV}, I=419 μAI = 419\ \mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always convert all input measurements to SI base units (meters, seconds, teslas) before substituting them into equations.

  • When converting area units, remember to square the linear conversion factor: (10−3 m/mm)2=10−6 m2/mm2(10^{-3}\text{ m/mm})^2 = 10^{-6}\text{ m}^2/\text{mm}^2.

Lock it in

Similar question

01

A single circular loop of wire has a diameter of 40.0 mm40.0\text{ mm} and is oriented perpendicular to a magnetic field increasing at 0.500 T/s0.500\text{ T/s}. Find the magnitude of the induced electromotive force in millivolts.

Answer

E=0.628 mV\mathcal{E} = 0.628\text{ mV}. First find r=20.0 mm=0.0200 mr = 20.0\text{ mm} = 0.0200\text{ m}. Area A=π(0.0200 m)2≈1.257×10−3 m2A = \pi (0.0200\text{ m})^2 \approx 1.257 \times 10^{-3}\text{ m}^2. Then E=AΔBΔt=(1.257×10−3 m2)(0.500 T/s)≈6.28×10−4 V=0.628 mV\mathcal{E} = A \frac{\Delta B}{\Delta t} = (1.257 \times 10^{-3}\text{ m}^2)(0.500\text{ T/s}) \approx 6.28 \times 10^{-4}\text{ V} = 0.628\text{ mV}.

02

A search coil with N=200N = 200 circular turns of diameter d=18.0 mmd = 18.0\text{ mm} is placed in a magnetic field directed perpendicular to its face. The magnetic field drops uniformly from 320 mT320\text{ mT} to zero in 40.0 ms40.0\text{ ms}. If the coil has total circuit resistance R=12.0 ΩR = 12.0\ \Omega, find the induced current in milliamperes.

Answer

I=33.9 mAI = 33.9\text{ mA}. Radius r=9.00 mm=0.00900 mr = 9.00\text{ mm} = 0.00900\text{ m}, area A=πr2≈2.545×10−4 m2A = \pi r^2 \approx 2.545 \times 10^{-4}\text{ m}^2. The rate of field change is ΔBΔt=0.320 T0.0400 s=8.00 T/s\frac{\Delta B}{\Delta t} = \frac{0.320\text{ T}}{0.0400\text{ s}} = 8.00\text{ T/s}. Induced EMF E=NAΔBΔt=200⋅(2.545×10−4 m2)⋅8.00 T/s≈0.4071 V\mathcal{E} = N A \frac{\Delta B}{\Delta t} = 200 \cdot (2.545 \times 10^{-4}\text{ m}^2) \cdot 8.00\text{ T/s} \approx 0.4071\text{ V}. Current I=ER=0.4071 V12.0 Ω≈33.9 mAI = \frac{\mathcal{E}}{R} = \frac{0.4071\text{ V}}{12.0\ \Omega} \approx 33.9\text{ mA}.

03

A circular sensor coil with N=300N = 300 turns of diameter d=30.0 mmd = 30.0\text{ mm} is tilted so that its normal vector makes an angle of 60.0∘60.0^\circ with a magnetic field changing at ΔBΔt=2.40 T/s\frac{\Delta B}{\Delta t} = 2.40\text{ T/s}. Calculate the induced EMF in volts.

Answer

E=0.254 V\mathcal{E} = 0.254\text{ V}. Radius r=15.0 mm=0.0150 mr = 15.0\text{ mm} = 0.0150\text{ m}, area A=π(0.0150 m)2≈7.069×10−4 m2A = \pi (0.0150\text{ m})^2 \approx 7.069 \times 10^{-4}\text{ m}^2. Magnetic flux through one turn is ΦB=BAcos⁡(60.0∘)\Phi_B = B A \cos(60.0^\circ). Thus E=NA(ΔBΔt)cos⁡(60.0∘)=300⋅(7.069×10−4 m2)⋅(2.40 T/s)⋅0.500≈0.254 V\mathcal{E} = N A \left(\frac{\Delta B}{\Delta t}\right) \cos(60.0^\circ) = 300 \cdot (7.069 \times 10^{-4}\text{ m}^2) \cdot (2.40\text{ T/s}) \cdot 0.500 \approx 0.254\text{ V}.

Loading workspace…