Resources

A uniform ladder of length L=5.00 mL = 5.00\text{ m} and mass M=18.0 kgM = 18.0\text{ kg} rests against a smooth, frictionless vertical wall, making an angle of θ=60.0∘\theta = 60.0^\circ with the rough horizontal ground. The coefficient of static friction between the base of the ladder and the ground is μs=0.420\mu_s = 0.420. A painter of mass m=72.0 kgm = 72.0\text{ kg} begins to climb the ladder. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the maximum distance dd along the ladder that the painter can climb from the bottom before the ladder begins to slip.

Answer and steps

Final answer

d=4.39 md = 4.39\text{ m}

Steps

01

Identify the Forces Acting on the Ladder

Model the ladder as a rigid body in static equilibrium. The forces acting on the ladder are:

  • Normal force from the ground (NgN_g): acts vertically upward at the base of the ladder.
  • Static friction force from the ground (fsf_s): acts horizontally toward the wall at the base, preventing the base from sliding outward.
  • Normal force from the vertical wall (NwN_w): acts horizontally away from the wall at the top of the ladder (the wall is smooth, so there is no vertical friction force at this contact point).
  • Weight of the ladder (MgM g): acts vertically downward at the ladder's center of mass, which is at the midpoint L2\frac{L}{2} from the base.
  • Weight of the painter (mgm g): acts vertically downward at a distance dd along the ladder from the base.

02

Apply Translational Equilibrium Conditions

For the ladder to remain stationary, the net external force in both the horizontal and vertical directions must be zero:

  1. Vertical equilibrium (∑Fy=0\sum F_y = 0): Ng−Mg−mg=0  ⟹  Ng=(M+m)gN_g - M g - m g = 0 \implies N_g = (M + m)g

    Substituting the given masses and g=9.80 m/s2g = 9.80\text{ m/s}^2: Ng=(18.0 kg+72.0 kg)(9.80 m/s2)=(90.0 kg)(9.80 m/s2)=882.0 NN_g = (18.0\text{ kg} + 72.0\text{ kg})(9.80\text{ m/s}^2) = (90.0\text{ kg})(9.80\text{ m/s}^2) = 882.0\text{ N}

  2. Horizontal equilibrium (∑Fx=0\sum F_x = 0): Nw−fs=0  ⟹  Nw=fsN_w - f_s = 0 \implies N_w = f_s

At the verge of slipping, the static friction force reaches its maximum threshold: fs,max⁡=μsNgf_{s,\max} = \mu_s N_g

Substituting the value of NgN_g: fs,max⁡=0.420⋅882.0 N=370.44 Nf_{s,\max} = 0.420 \cdot 882.0\text{ N} = 370.44\text{ N}

Therefore, the maximum horizontal normal force the wall can provide before the ladder slips is: Nw=370.44 NN_w = 370.44\text{ N}


03

Apply Rotational Equilibrium Condition

To find the maximum distance dd, consider the balance of torques. Choosing the base of the ladder (the contact point with the ground) as the pivot eliminates the unknown forces NgN_g and fsf_s from the torque equation:

∑τbase=0\sum \tau_{\text{base}} = 0

  • Counter-clockwise torque caused by the normal force from the wall: τNw=Nw(Lsin⁡θ)\tau_{N_w} = N_w (L \sin\theta)
  • Clockwise torque caused by the weight of the ladder: τladder=Mg(L2cos⁡θ)\tau_{\text{ladder}} = M g \left(\frac{L}{2} \cos\theta\right)
  • Clockwise torque caused by the weight of the painter: τpainter=mg(dcos⁡θ)\tau_{\text{painter}} = m g (d \cos\theta)

Setting the net torque to zero: NwLsin⁡θ=Mg(L2)cos⁡θ+mgdcos⁡θN_w L \sin\theta = M g \left(\frac{L}{2}\right)\cos\theta + m g d \cos\theta


04

Solve for the Maximum Distance dd

Divide both sides by cos⁡θ\cos\theta (noting that sin⁡θcos⁡θ=tan⁡θ\frac{\sin\theta}{\cos\theta} = \tan\theta): NwLtan⁡θ=Mg(L2)+mgdN_w L \tan\theta = M g \left(\frac{L}{2}\right) + m g d

Rearrange to solve for dd: d=NwLtan⁡θ−12MgLmgd = \frac{N_w L \tan\theta - \frac{1}{2} M g L}{m g}

Substitute Nw=μs(M+m)gN_w = \mu_s (M + m)g, which allows gg to cancel: d=μs(M+m)Ltan⁡θ−12MLmd = \frac{\mu_s (M + m) L \tan\theta - \frac{1}{2} M L}{m}

Substitute the numerical values:

  • L=5.00 mL = 5.00\text{ m}
  • M=18.0 kgM = 18.0\text{ kg}
  • m=72.0 kgm = 72.0\text{ kg}
  • μs=0.420\mu_s = 0.420
  • θ=60.0∘  ⟹  tan⁡60.0∘=3≈1.732\theta = 60.0^\circ \implies \tan 60.0^\circ = \sqrt{3} \approx 1.732

Evaluating the terms: d=4.39 md = 4.39\text{ m}

Common Pitfall: A frequent mistake is forgetting to include the ladder's own weight in both the vertical normal force NgN_g and the torque equation. As the painter climbs higher, the clockwise torque increases, requiring a larger wall force NwN_w and therefore a greater static friction fsf_s at the base; slipping occurs as soon as the demanded friction exceeds μsNg\mu_s N_g.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that the ladder itself has mass and omits the gravitational force of the ladder in the torque equation and normal force calculation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Nground=mg=72.0×9.80=705.6 NN_{\text{ground}} = m g = 72.0 \times 9.80 = 705.6\text{ N}

    Correct

    Nground=(M+m)g=(18.0 kg+72.0 kg)(9.80 m/s2)=882.0 NN_{\text{ground}} = (M + m)g = (18.0\text{ kg} + 72.0\text{ kg})(9.80\text{ m/s}^2) = 882.0\text{ N}

    You only included the painter's weight in the vertical force balance. The ladder is uniform and has its own mass M=18.0 kgM = 18.0\text{ kg}, which also pushes down on the ground.

  2. Step 2

    fs=μsNground=0.420×705.6=296.35 N  ⟹  Nwall=fs=296.35 Nf_s = \mu_s N_{\text{ground}} = 0.420 \times 705.6 = 296.35\text{ N} \implies N_{\text{wall}} = f_s = 296.35\text{ N}

    Correct

    fs,max⁡=μsNground=0.420×882.0 N=370.44 N  ⟹  Nwall=370.44 Nf_{s,\max} = \mu_s N_{\text{ground}} = 0.420 \times 882.0\text{ N} = 370.44\text{ N} \implies N_{\text{wall}} = 370.44\text{ N}

    Your relationship between maximum static friction and the wall's normal force is conceptually sound, but the numerical value is carried over from the incomplete ground normal force.

  3. Step 3

    NwallLsin⁡60∘−mgdcos⁡60∘=0N_{\text{wall}} L \sin 60^\circ - m g d \cos 60^\circ = 0

    Correct

    NwallLsin⁡60∘−Mg(L2)cos⁡60∘−mgdcos⁡60∘=0N_{\text{wall}} L \sin 60^\circ - M g \left(\frac{L}{2}\right)\cos 60^\circ - m g d \cos 60^\circ = 0

    You omitted the clockwise torque produced by the ladder's weight acting at its center of mass, Mg(L2)cos⁡60∘M g \left(\frac{L}{2}\right)\cos 60^\circ.

  4. Step 4

    d=NwallLtan⁡60∘mg=296.35×5.00×1.732705.6≈3.64 md = \frac{N_{\text{wall}} L \tan 60^\circ}{m g} = \frac{296.35 \times 5.00 \times 1.732}{705.6} \approx 3.64\text{ m}

    Correct

    d=NwallLtan⁡60∘−12MgLmg=4.39 md = \frac{N_{\text{wall}} L \tan 60^\circ - \frac{1}{2} M g L}{m g} = 4.39\text{ m}

    Your algebraic manipulation was executed cleanly, but the final distance is incorrect due to the missing ladder mass terms.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that at the verge of slipping, static friction reaches its maximum value fs=μsNgroundf_s = \mu_s N_{\text{ground}}.

You chose the base of the ladder as your pivot, which successfully eliminated both unknown forces at the ground from the torque calculation.

You used correct trigonometric lever arms for the vertical weights and the horizontal wall force.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Non-Negligible Body Weight in Equilibrium

You treated the ladder as massless rather than accounting for its given mass of 18.0 kg18.0\text{ kg}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In rigid-body statics, any object with a given mass or density experiences gravity at its center of mass. Forgetting to draw the ladder's own gravity on the free-body diagram led to missing terms in both translational (vertical) and rotational equilibrium.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Non-Negligible Mass
  • Every body with mass MM contributes a downward gravitational force MgM g at its center of mass.

  • Before writing equilibrium equations, list every mass mentioned in the problem and draw their weight vectors on the free-body diagram.

Include All Vertical Forces
  • ∑Fy=0  ⟹  Nground=∑mig\sum F_y = 0 \implies N_{\text{ground}} = \sum m_i g.

  • Sum the weights of both the person and the structure itself when finding the normal force supporting them.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the complete torque equation about the base: NwallLsin⁡60∘=Mg(L2)cos⁡60∘+mgdcos⁡60∘N_{\text{wall}} L \sin 60^\circ = M g \left(\frac{L}{2}\right)\cos 60^\circ + m g d \cos 60^\circ

  2. Divide by cos⁡60∘\cos 60^\circ to simplify: NwallLtan⁡60∘=12MgL+mgdN_{\text{wall}} L \tan 60^\circ = \frac{1}{2} M g L + m g d

  3. Substitute Nwall=370.44 NN_{\text{wall}} = 370.44\text{ N}, M=18.0 kgM = 18.0\text{ kg}, m=72.0 kgm = 72.0\text{ kg}, and L=5.00 mL = 5.00\text{ m}: 370.44×5.00×3=12(18.0)(9.80)(5.00)+(72.0)(9.80)d370.44 \times 5.00 \times \sqrt{3} = \frac{1}{2}(18.0)(9.80)(5.00) + (72.0)(9.80)d

  4. Simplify the terms: 3208.11=441.0+705.6d  ⟹  705.6d=2767.113208.11 = 441.0 + 705.6 d \implies 705.6 d = 2767.11

  5. Solve for dd: d=2767.11705.6≈4.39 md = \frac{2767.11}{705.6} \approx 4.39\text{ m}

Final answer

d=4.39 md = 4.39\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always start rigid-body equilibrium problems by drawing a full free-body diagram that includes the weight of the structure itself at its center of mass.

  • Verify your vertical force sum ∑Fy=0\sum F_y = 0 against every downward gravitational force before calculating friction.

OverviewACEpath Teacher's Diagnosis

02 The student swaps the sine and cosine components of the lever arms when setting up the torque balance equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Nground=(M+m)g=(18.0+72.0)×9.80=882 N  ⟹  fs=μsNground=370.44 N  ⟹  Nwall=fs=370.44 NN_{\text{ground}} = (M+m)g = (18.0+72.0)\times 9.80 = 882\text{ N} \implies f_s = \mu_s N_{\text{ground}} = 370.44\text{ N} \implies N_{\text{wall}} = f_s = 370.44\text{ N}

  2. Step 2

    Torque about base: NwallLcos⁡60∘−Mg(L2)sin⁡60∘−mgdsin⁡60∘=0\text{Torque about base: } N_{\text{wall}} L \cos 60^\circ - Mg\left(\frac{L}{2}\right)\sin 60^\circ - mgd\sin 60^\circ = 0

    Correct

    ∑τbase=Nwall(Lsin⁡60∘)−Mg(L2cos⁡60∘)−mg(dcos⁡60∘)=0\sum \tau_{\text{base}} = N_{\text{wall}}(L\sin 60^\circ) - Mg\left(\frac{L}{2}\cos 60^\circ\right) - mg(d\cos 60^\circ) = 0

    You inverted the trigonometric components for the lever arms. The horizontal force NwallN_{\text{wall}} acts at a vertical height of Lsin⁡60∘L\sin 60^\circ above the base, while the vertical gravitational forces act at horizontal distances L2cos⁡60∘\frac{L}{2}\cos 60^\circ and dcos⁡60∘d\cos 60^\circ from the base.

  3. Step 3

    NwallL−Mg(L2)tan⁡60∘−mgdtan⁡60∘=0  ⟹  d=NwallLtan⁡60∘−Mg(L2)mg≈0.89 mN_{\text{wall}}L - Mg\left(\frac{L}{2}\right)\tan 60^\circ - mgd\tan 60^\circ = 0 \implies d = \frac{\frac{N_{\text{wall}}L}{\tan 60^\circ} - Mg\left(\frac{L}{2}\right)}{mg} \approx 0.89\text{ m}

    Correct

    NwallLtan⁡60∘−Mg(L2)−mgd=0  ⟹  d=NwallLtan⁡60∘−12MgLmg≈4.39 mN_{\text{wall}}L\tan 60^\circ - Mg\left(\frac{L}{2}\right) - mgd = 0 \implies d = \frac{N_{\text{wall}}L\tan 60^\circ - \frac{1}{2}MgL}{mg} \approx 4.39\text{ m}

    Your algebraic isolation and numerical calculation were executed logically based on your previous torque equation, but the numerical result is incorrect due to the swapped trigonometric components in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly balanced the vertical forces to find the ground normal force.

You used the maximum static friction condition properly to relate the ground friction to the wall normal force.

You chose the base of the ladder as the pivot point, which effectively eliminated the unknowns at the ground from the torque equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Lever Arm Inversion

You associated horizontal distances with sin⁡θ\sin\theta and vertical distances with cos⁡θ\cos\theta instead of using the geometric definitions relative to the ground angle θ\theta.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misidentifying the perpendicular distance (lever arm) between the pivot point and the line of action for horizontal versus vertical forces.

REASONING PATH
Your ACEpath teacher’s suggested approach
Perpendicular Lever Arm for Vertical Forces
  • For a vertical force F⃗y\vec{F}_y acting at distance rr along an incline making an angle θ\theta with the horizontal floor, the lever arm is the horizontal distance: r⊥=rcos⁡θr_\perp = r\cos\theta.

  • Always draw a right triangle to confirm that the horizontal baseline adjacent to angle θ\theta uses cosine.

Perpendicular Lever Arm for Horizontal Forces
  • For a horizontal force F⃗x\vec{F}_x acting at distance rr along an incline making an angle θ\theta with the horizontal floor, the lever arm is the vertical height: r⊥=rsin⁡θr_\perp = r\sin\theta.

  • Check that the vertical side opposite to angle θ\theta uses sine for the lever arm of a horizontal force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the torque balance using correct perpendicular distances: Nwall(Lsin⁡60∘)=Mg(L2cos⁡60∘)+mg(dcos⁡60∘)N_{\text{wall}}(L\sin 60^\circ) = Mg\left(\frac{L}{2}\cos 60^\circ\right) + mg(d\cos 60^\circ).

  2. Divide the entire equation by cos⁡60∘\cos 60^\circ: NwallLtan⁡60∘=12MgL+mgdN_{\text{wall}}L\tan 60^\circ = \frac{1}{2}MgL + mgd.

  3. Solve for dd: d=NwallLtan⁡60∘−12MgLmgd = \frac{N_{\text{wall}}L\tan 60^\circ - \frac{1}{2}MgL}{mg}.

  4. Substitute the known values: d=(370.44)(5.00)(tan⁡60∘)−0.5(18.0)(9.80)(5.00)(72.0)(9.80)=3208.11−441.0705.6=2767.11705.6≈4.39 md = \frac{(370.44)(5.00)(\tan 60^\circ) - 0.5(18.0)(9.80)(5.00)}{(72.0)(9.80)} = \frac{3208.11 - 441.0}{705.6} = \frac{2767.11}{705.6} \approx 4.39\text{ m}.

Final answer

d=4.39 md = 4.39\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the perpendicular line from the pivot to the line of action of each force before writing torque terms.

  • Verify your angle relationships using simple extreme angles, such as checking if the height vanishes when θ=0∘\theta = 0^\circ.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the normal force from the ground using only the painter's mass but includes the ladder's mass in the torque equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Nground=mg=705.6 NN_{\text{ground}} = m g = 705.6\text{ N}

    Correct

    Nground=(M+m)g=(18.0 kg+72.0 kg)(9.80 m/s2)=882.0 NN_{\text{ground}} = (M + m)g = (18.0\text{ kg} + 72.0\text{ kg})(9.80\text{ m/s}^2) = 882.0\text{ N}

    In vertical translational equilibrium (∑Fy=0\sum F_y = 0), the ground supports both the painter and the ladder itself (Nground−Mg−mg=0N_{\text{ground}} - M g - m g = 0). Leaving out the ladder's weight underestimates the normal force.

  2. Step 2

    fs=μsNground=0.420×705.6=296.35 N  ⟹  Nwall=fs=296.35 Nf_s = \mu_s N_{\text{ground}} = 0.420 \times 705.6 = 296.35\text{ N} \implies N_{\text{wall}} = f_s = 296.35\text{ N}

    Correct

    fs,max⁡=μsNground=0.420×882.0 N=370.44 N  ⟹  Nwall=370.44 Nf_{s,\max} = \mu_s N_{\text{ground}} = 0.420 \times 882.0\text{ N} = 370.44\text{ N} \implies N_{\text{wall}} = 370.44\text{ N}

    Your application of horizontal equilibrium and maximum static friction was correct in principle, but the numerical result was affected by the underestimated normal force.

  3. Step 3

    Torque about base: NwallLsin⁡60∘−Mg(L2)cos⁡60∘−mgdcos⁡60∘=0\text{Torque about base: } N_{\text{wall}} L \sin 60^\circ - M g \left(\frac{L}{2}\right) \cos 60^\circ - m g d \cos 60^\circ = 0

  4. Step 4

    d=NwallLtan⁡60∘−Mg(L/2)mg=296.35×5.00×1.732−18.0×9.80×2.5072.0×9.80≈3.01 md = \frac{N_{\text{wall}} L \tan 60^\circ - M g (L/2)}{m g} = \frac{296.35 \times 5.00 \times 1.732 - 18.0 \times 9.80 \times 2.50}{72.0 \times 9.80} \approx 3.01\text{ m}

    Correct

    d=370.44×5.00×tan⁡60∘−18.0×9.80×2.5072.0×9.80≈4.39 md = \frac{370.44 \times 5.00 \times \tan 60^\circ - 18.0 \times 9.80 \times 2.50}{72.0 \times 9.80} \approx 4.39\text{ m}

    You rearranged the torque equation and solved for dd algebraically with great skill, but the value is incorrect due to the propagated value of NwallN_{\text{wall}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly formulated the rotational equilibrium equation about the base of the ladder, accounting for all counteracting torques and their angular components.

You correctly applied horizontal equilibrium to equate the normal force from the vertical wall to the maximum static friction force.

You isolated the target variable dd accurately through clean algebraic steps.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted object weight in normal force

You calculated Nground=mgN_{\text{ground}} = mg instead of (M+m)g(M + m)g, forgetting to include the ladder's weight in the vertical force balance.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Incomplete free-body force accounting in translational equilibrium: you recognized that the ladder has weight when forming the torque equation, but overlooked it when summing vertical forces at the ground contact point.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check vertical force balance
  • ∑Fy=0  ⟹  Nground=∑(downward forces)\sum F_y = 0 \implies N_{\text{ground}} = \sum(\text{downward forces})

  • Always list every downward gravitational force (ladder, person, tools) before calculating NgroundN_{\text{ground}}.

Verify friction threshold dependence
  • fs,max⁡=μsNgroundf_{s,\max} = \mu_s N_{\text{ground}}

  • Ensure NgroundN_{\text{ground}} reflects the full weight of the combined system before computing available friction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Nground=(M+m)g=(18.0+72.0)(9.80)=882.0 NN_{\text{ground}} = (M + m)g = (18.0 + 72.0)(9.80) = 882.0\text{ N}

  2. Nwall=fs,max⁡=μsNground=0.420×882.0=370.44 NN_{\text{wall}} = f_{s,\max} = \mu_s N_{\text{ground}} = 0.420 \times 882.0 = 370.44\text{ N}

  3. d=NwallLtan⁡60.0∘−12MgLmg=(370.44)(5.00)(3)−(0.5)(18.0)(9.80)(5.00)(72.0)(9.80)d = \frac{N_{\text{wall}} L \tan 60.0^\circ - \frac{1}{2} M g L}{m g} = \frac{(370.44)(5.00)(\sqrt{3}) - (0.5)(18.0)(9.80)(5.00)}{(72.0)(9.80)}

Final answer

d=4.39 md = 4.39\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw a complete free-body diagram showing all downward gravity vectors before writing equilibrium equations.

  • Check that every mass given in the problem statement appears in both translational and rotational equilibrium conditions.

Lock it in

Similar question

01

A uniform plank of length 4.0 m4.0\text{ m} and mass 20 kg20\text{ kg} rests on two supports, one at each end. A 60 kg60\text{ kg} student stands 1.0 m1.0\text{ m} from the left support. Find the upward support force at the right end. (Use g=9.8 m/s2g = 9.8\text{ m/s}^2)

Answer

Fright=245 NF_{\text{right}} = 245\text{ N}. Key steps: Take torques about the left support: ∑τ=0  ⟹  Fright(4.0)−(20g)(2.0)−(60g)(1.0)=0  ⟹  4Fright=40g+60g=100g  ⟹  Fright=25g=245 N\sum \tau = 0 \implies F_{\text{right}}(4.0) - (20g)(2.0) - (60g)(1.0) = 0 \implies 4 F_{\text{right}} = 40g + 60g = 100g \implies F_{\text{right}} = 25g = 245\text{ N}.

02

A uniform ladder of mass M=15 kgM = 15\text{ kg} and length L=6.0 mL = 6.0\text{ m} leans against a smooth vertical wall at an angle of 45∘45^\circ with the ground. If no person is on the ladder, what minimum coefficient of static friction μs\mu_s between the ground and the ladder is required to prevent slipping?

Answer

μs≥0.50\mu_s \ge 0.50. Key steps: Ng=MgN_g = M g. Torque about the base: NwLsin⁡45∘−Mg(L2)cos⁡45∘=0  ⟹  Nw=12MgN_w L \sin 45^\circ - M g \left(\frac{L}{2}\right)\cos 45^\circ = 0 \implies N_w = \frac{1}{2} M g. Horizontal balance requires fs=Nw=12Mgf_s = N_w = \frac{1}{2} M g. To prevent slip: fs≤μsNg  ⟹  12Mg≤μsMg  ⟹  μs≥0.50f_s \le \mu_s N_g \implies \frac{1}{2} M g \le \mu_s M g \implies \mu_s \ge 0.50.

03

A uniform 25.0 kg25.0\text{ kg} boom of length 4.00 m4.00\text{ m} is hinged at a wall and held horizontally by a cable attached to its outer tip at an angle of 30.0∘30.0^\circ above the horizontal. A 50.0 kg50.0\text{ kg} load hangs from the tip. Calculate the tension TT in the cable. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

T=1225 NT = 1225\text{ N} (or 1.23 kN1.23\text{ kN}). Key steps: Pivot at the hinge: ∑τ=T(Lsin⁡30∘)−Mg(L/2)−mgL=0\sum \tau = T(L\sin 30^\circ) - M g (L/2) - m g L = 0. Divide by LL: Tsin⁡30∘=12Mg+mg=(12.5+50.0)g=62.5gT \sin 30^\circ = \frac{1}{2} M g + m g = (12.5 + 50.0)g = 62.5g. Thus T=62.5×9.80sin⁡30∘=1225 NT = \frac{62.5 \times 9.80}{\sin 30^\circ} = 1225\text{ N}.

Loading workspace…