Resources
A microscopic particle of mass carrying an electrostatic charge moves along a rectilinear path of length through a viscous liquid column. The fluid exerts a non-conservative drag force opposed to motion with average magnitude . Simultaneously, an external electric field does of positive work on the particle. Expressing all quantities in standard SI units: (a) convert to newtons () and the particle mass to kilograms (), (b) calculate the non-conservative work done by the fluid drag in joules, and (c) find the resulting net change in kinetic energy of the particle in nanojoules ().
Answer and steps
Final answer
(a) , ; (b) ; (c) (or )
Steps
Part (a): Conversion to SI Units
- Drag Force (): The dyne () is the CGS unit of force, related to the newton () by: Converting the given drag force:
- Mass (): A microgram () is related to the kilogram () by: Therefore:
Part (b): Work Done by Fluid Drag
The work done by a constant force over a straight displacement is given by: where:
- because the drag force directly opposes the direction of displacement ().
Calculating the work done by the drag force:
Common Pitfall: Forgetting the negative sign for resistive forces. Because drag acts opposite to the direction of motion, it removes mechanical energy from the particle, doing strictly negative work.
Part (c): Net Change in Kinetic Energy
According to the Work-Energy Theorem, the net work done by all forces equals the change in kinetic energy of the particle:
Substitute the values in joules:
To express this value in nanojoules (), where :
The negative sign indicates that the resistive fluid drag dissipated more energy than the electric field supplied, resulting in a net decrease in the particle's kinetic energy.
Typical errors
01 The student forgets that drag force opposes the displacement, treating the work done by drag as positive and resulting in an incorrect positive sum for change in kinetic energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because drag opposes the displacement (), the work done by drag is negative: .
- Step 3Correct
Your work-energy setup was structurally correct, but using the positive value for produced instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately converted dynes to newtons and micrograms to kilograms.
You converted the displacement from centimeters to meters correctly.
You properly set up the work-energy theorem .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeOmitting the negative sign or factor when calculating work done by a resistive drag force.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating work done by a force as simply force magnitude times displacement magnitude without accounting for the angle between the force vector and the displacement vector. Resistive forces like friction and fluid drag oppose motion, removing energy from the particle and doing strictly negative work.
REASONING PATH
Your ACEpath teacher’s suggested approach- Vector Direction Check
Always identify the relative direction between force and displacement before multiplying magnitudes. If , include a negative sign explicitly.
- Physical Consistency Check
Resistive forces remove kinetic energy from a moving system.
Check whether the force aids motion (positive work) or hinders motion (negative work). Drag forces must always do negative work on a moving object.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) , ; (b) ; (c)
02 The student fails to convert the displacement from centimeters to meters, resulting in a work value that is two orders of magnitude too large.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You recognized that drag opposes motion and does negative work, but you substituted directly in centimeters rather than converting to meters ().
- Step 3Correct
You correctly applied the Work-Energy Theorem and converted your result to nanojoules, but the numerical answer is off because it used the incorrect value of from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted force from dynes to newtons and mass from micrograms to kilograms.
You correctly identified that the resistive drag force does negative work.
You correctly stated and applied the Work-Energy Theorem .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted as instead of converting to meters ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou overlooked checking whether all input variables were in standard base SI units (meters for distance) before evaluating the work formula .
REASONING PATH
Your ACEpath teacher’s suggested approach- SI Base Units for Mechanical Work
The joule is defined as ; displacement must always be expressed in meters () before calculating work.
Check and explicitly write down unit conversions for all distance/displacement values (e.g., ) before substituting them into work equations.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert displacement to SI base units: .
Calculate the work done by drag: .
Sum the work terms to find net work: .
Convert the change in kinetic energy to nanojoules: .
(a) , ; (b) ; (c)
03 The student incorrectly treats microgram as 10⁻⁶ kilograms instead of 10⁻⁹ kilograms by confusing conversion from grams with conversion from kilograms.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The prefix micro () means , which converts micrograms to grams (). Because the standard SI unit of mass is the kilogram (), you must divide by another , giving .
- Step 3
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the drag force from dynes to newtons.
You properly identified that resistive fluid drag does negative work on the moving particle.
You correctly used the work-energy theorem to find the net change in kinetic energy and converted the result to nanojoules.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou applied the factor directly from micrograms to kilograms, bypassing the intermediate base unit of grams.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the metric prefix reference unit: SI prefixes (such as micro, milli, and centi) attach to the base unit 'gram' (), but the standard coherent SI base unit for mechanics is the 'kilogram' (). Consequently, converting a prefixed gram unit to kilograms requires two steps: first to grams (), then to kilograms ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Two-Step Mass Conversion to SI
Prefixes apply to grams (), but SI calculations require kilograms (): .
Whenever you see a prefixed mass unit (like or ), convert first to grams using the prefix power, then multiply by to reach standard kilograms.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) , ; (b) ; (c)
Lock it in
When a force acts directly opposite to the displacement vector, what is the work done by that force?
(strictly negative), because and .
Similar question
A block slides along a rough horizontal table. The kinetic friction force opposing motion is . Concurrently, a pulling force does of work on the block. Calculate (a) the work done by friction and (b) the net change in kinetic energy of the block.
Answer
(a) ; (b) .
A charged bead moves through an oil bath. An electric force does of work. Viscous drag opposes motion with an average force of . Find the net change in kinetic energy in microjoules ().
Answer
Work done by drag: . Net work: .
A particle of mass enters a resistive medium with an initial kinetic energy of . A constant retarding drag force of acts on it over a distance of while no external driving force acts. What is the final kinetic energy of the particle in nanojoules?
Answer
. . By the work-energy theorem: .