Resources

An uncharged 47.0 μF47.0\text{ }\mu\text{F} capacitor is connected in series with a 150 kΩ150\text{ }\text{k}\Omega resistor and a 12.0 V12.0\text{ V} DC power supply. The switch is closed at time t=0 st = 0\text{ s}. (a) Calculate the capacitive time constant τ\tau of the circuit. (b) Determine the charge qq stored on the capacitor plates and the current ii in the circuit at t=10.0 st = 10.0\text{ s}.

Answer and steps

Final answer

(a) τ=7.05 s\tau = 7.05\text{ s}; (b) q=4.27×10−4 Cq = 4.27 \times 10^{-4}\text{ C} (or 427 μC427\text{ }\mu\text{C}), i=1.94×10−5 Ai = 1.94 \times 10^{-5}\text{ A} (or 19.4 μA19.4\text{ }\mu\text{A})

Steps

01

Charge on the Capacitor

Part (a): Calculating the Time Constant τ\tau

In a series resistance-capacitance (RCRC) circuit, the capacitive time constant τ\tau characterizes the rate at which the capacitor charges or discharges. It is defined as: τ=RC\tau = R C Convert the given values into base SI units:

  • Resistance: R=150 kΩ=150×103 ΩR = 150\text{ k}\Omega = 150 \times 10^3\text{ }\Omega
  • Capacitance: C=47.0 μF=47.0×10−6 FC = 47.0\text{ }\mu\text{F} = 47.0 \times 10^{-6}\text{ F} Substitute these values into the formula: τ=(150×103 Ω)(47.0×10−6 F)=7.05 s\tau = (150 \times 10^3\text{ }\Omega)(47.0 \times 10^{-6}\text{ F}) = 7.05\text{ s}

Part (b): Finding Charge qq and Current ii at t=10.0 st = 10.0\text{ s}

When connected to a constant voltage supply E=12.0 V\mathcal{E} = 12.0\text{ V}, an initially uncharged capacitor accumulates charge according to the charging equation:

q(t)=Qmax(1−e−t/τ)q(t) = Q_{\text{max}}\left(1 - e^{-t/\tau}\right)

where the maximum charge QmaxQ_{\text{max}} is the charge stored when the capacitor is fully charged:

Qmax=CE=(47.0×10−6 F)(12.0 V)=5.64×10−4 CQ_{\text{max}} = C \mathcal{E} = (47.0 \times 10^{-6}\text{ F})(12.0\text{ V}) = 5.64 \times 10^{-4}\text{ C}

Now evaluate the exponential decay factor at t=10.0 st = 10.0\text{ s}:

tτ=10.0 s7.05 s≈1.4184\frac{t}{\tau} = \frac{10.0\text{ s}}{7.05\text{ s}} \approx 1.4184

e−t/τ=e−1.4184≈0.2421e^{-t/\tau} = e^{-1.4184} \approx 0.2421

Substitute this back into the charge formula:

q(10.0 s)=(5.64×10−4 C)(1−0.2421)=(5.64×10−4 C)(0.7579)≈4.27×10−4 Cq(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C})(1 - 0.2421) = (5.64 \times 10^{-4}\text{ C})(0.7579) \approx 4.27 \times 10^{-4}\text{ C}

Expressing this in microcoulombs gives q=427 μCq = 427\text{ }\mu\text{C}.

02

Current in the Circuit

As the capacitor charges, its opposing potential difference increases, causing the circuit current to decay exponentially from its initial maximum value I0I_0:

i(t)=I0e−t/τi(t) = I_0 e^{-t/\tau}

The initial current at t=0 st = 0\text{ s} is determined entirely by the resistor:

I0=ER=12.0 V150×103 Ω=8.00×10−5 AI_0 = \frac{\mathcal{E}}{R} = \frac{12.0\text{ V}}{150 \times 10^3\text{ }\Omega} = 8.00 \times 10^{-5}\text{ A}

Using the calculated exponential factor e−t/τ≈0.2421e^{-t/\tau} \approx 0.2421:

i(10.0 s)=(8.00×10−5 A)(0.2421)≈1.94×10−5 Ai(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A})(0.2421) \approx 1.94 \times 10^{-5}\text{ A}

Expressing this in microamperes gives i=19.4 μAi = 19.4\text{ }\mu\text{A}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the charging expression (1 - e^(-t/τ)) with the discharging expression e^(-t/τ) when calculating the stored charge, yielding an undercalculated charge.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=RC=(150×103 Ω)(47.0×10−6 F)=7.05 s\tau = RC = (150 \times 10^3\text{ }\Omega)(47.0 \times 10^{-6}\text{ F}) = 7.05\text{ s}

  2. Step 2

    Qmax=CV=(47.0×10−6 F)(12.0 V)=5.64×10−4 CQ_{\text{max}} = CV = (47.0 \times 10^{-6}\text{ F})(12.0\text{ V}) = 5.64 \times 10^{-4}\text{ C}

  3. Step 3

    q(10.0 s)=Qmax⋅e−t/τ  ⟹  q(10.0 s)=(5.64×10−4 C)⋅e−10.0/7.05=1.37×10−4 Cq(10.0\text{ s}) = Q_{\text{max}} \cdot e^{-t/\tau} \implies q(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C}) \cdot e^{-10.0/7.05} = 1.37 \times 10^{-4}\text{ C}

    Correct

    q(10.0 s)=Qmax(1−e−t/τ)=(5.64×10−4 C)(1−e−10.0/7.05)≈4.27×10−4 Cq(10.0\text{ s}) = Q_{\text{max}}\left(1 - e^{-t/\tau}\right) = (5.64 \times 10^{-4}\text{ C})\left(1 - e^{-10.0/7.05}\right) \approx 4.27 \times 10^{-4}\text{ C}

    Because the capacitor starts uncharged and is charging up toward QmaxQ_{\text{max}}, the stored charge increases according to q(t)=Qmax(1−e−t/τ)q(t) = Q_{\text{max}}(1 - e^{-t/\tau}). The formula Qmaxe−t/τQ_{\text{max}}e^{-t/\tau} models exponential decay during discharging.

  4. Step 4

    I0=VR=12.0 V150×103 Ω=8.00×10−5 A  ⟹  i(10.0 s)=I0⋅e−10.0/7.05=1.94×10−5 AI_0 = \frac{V}{R} = \frac{12.0\text{ V}}{150 \times 10^3\text{ }\Omega} = 8.00 \times 10^{-5}\text{ A} \implies i(10.0\text{ s}) = I_0 \cdot e^{-10.0/7.05} = 1.94 \times 10^{-5}\text{ A}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the circuit time constant τ=RC=7.05 s\tau = RC = 7.05\text{ s}.

You calculated the full saturation charge Qmax=5.64×10−4 CQ_{\text{max}} = 5.64 \times 10^{-4}\text{ C} accurately.

You correctly modeled and computed the decaying circuit current i(10.0 s)=1.94×10−5 Ai(10.0\text{ s}) = 1.94 \times 10^{-5}\text{ A}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula confusion (charging vs. discharging)

You used the exponential decay factor e−t/τe^{-t/\tau} instead of the accumulation factor (1−e−t/τ)(1 - e^{-t/\tau}) when finding the charge on a charging capacitor.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the transient behavior of quantities that build up from zero with quantities that decay toward zero. While current i(t)i(t) decays toward zero in both charging and discharging, charge q(t)q(t) accumulates from 00 to QmaxQ_{\text{max}} during charging.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Boundary Conditions at $t = 0$
  • For an initially uncharged capacitor, q(0)=0q(0) = 0.

  • Always test t=0t = 0: Qmaxe−0/τ=Qmax≠0Q_{\text{max}}e^{-0/\tau} = Q_{\text{max}} \neq 0, whereas Qmax(1−e−0/τ)=0Q_{\text{max}}(1 - e^{-0/\tau}) = 0.

Distinguish Growing vs. Decaying Quantities
  • Quantities that rise from zero toward a maximum use (1−e−t/τ)(1 - e^{-t/\tau}); quantities decaying to zero use e−t/τe^{-t/\tau}.

  • Verify whether the physical quantity increases or decreases over time before selecting the exponential function.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the correct charging expression: q(t)=Qmax(1−e−t/τ)q(t) = Q_{\text{max}}\left(1 - e^{-t/\tau}\right).

  2. Evaluate the exponential term: e−10.0/7.05≈e−1.4184≈0.2421e^{-10.0/7.05} \approx e^{-1.4184} \approx 0.2421.

  3. Calculate the growth factor: 1−e−t/τ=1−0.2421=0.75791 - e^{-t/\tau} = 1 - 0.2421 = 0.7579.

  4. Compute the charge: q(10.0 s)=(5.64×10−4 C)(0.7579)≈4.27×10−4 Cq(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C})(0.7579) \approx 4.27 \times 10^{-4}\text{ C} (or 427 μC427\text{ }\mu\text{C}).

Final answer

(a) τ=7.05 s\tau = 7.05\text{ s}; (b) q=4.27×10−4 Cq = 4.27 \times 10^{-4}\text{ C}, i=1.94×10−5 Ai = 1.94 \times 10^{-5}\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice checking boundary values at t=0t = 0 and t→∞t \to \infty to verify transient equations.

  • Review the distinction between capacitor voltage/charge (accumulating) and circuit current (decaying) during charging.

OverviewACEpath Teacher's Diagnosis

02 The student misapplies the charging formula factor (1 - e^(-t/τ)) to the current instead of using the exponential decay factor, resulting in an increasing current over time.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=RC=(150×103 Ω)(47.0×10−6 F)=7.05 s\tau = RC = (150 \times 10^3\text{ }\Omega)(47.0 \times 10^{-6}\text{ F}) = 7.05\text{ s}

  2. Step 2

    Qmax=CV=(47.0×10−6 F)(12.0 V)=5.64×10−4 C  ⟹  q(10.0 s)=(5.64×10−4 C)(1−e−10.0/7.05)=4.27×10−4 CQ_{\text{max}} = CV = (47.0 \times 10^{-6}\text{ F})(12.0\text{ V}) = 5.64 \times 10^{-4}\text{ C} \implies q(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C})\left(1 - e^{-10.0/7.05}\right) = 4.27 \times 10^{-4}\text{ C}

  3. Step 3

    I0=12.0 V150×103 Ω=8.00×10−5 AI_0 = \frac{12.0\text{ V}}{150 \times 10^3\text{ }\Omega} = 8.00 \times 10^{-5}\text{ A}

  4. Step 4

    i(10.0 s)=I0(1−e−t/τ)  ⟹  i(10.0 s)=(8.00×10−5 A)(1−e−10.0/7.05)=6.06×10−5 Ai(10.0\text{ s}) = I_0\left(1 - e^{-t/\tau}\right) \implies i(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A})\left(1 - e^{-10.0/7.05}\right) = 6.06 \times 10^{-5}\text{ A}

    Correct

    i(t)=I0e−t/τ  ⟹  i(10.0 s)=(8.00×10−5 A)e−10.0/7.05≈1.94×10−5 Ai(t) = I_0 e^{-t/\tau} \implies i(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A})e^{-10.0/7.05} \approx 1.94 \times 10^{-5}\text{ A}

    During charging, the opposing potential across the capacitor builds up, causing the current to decay exponentially from I0I_0 toward zero according to i(t)=I0e−t/τi(t) = I_0 e^{-t/\tau}, rather than increasing with (1−e−t/τ)(1 - e^{-t/\tau}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the capacitive time constant τ=RC\tau = RC.

You correctly applied the charging equation q(t)=Qmax(1−e−t/τ)q(t) = Q_{\text{max}}(1 - e^{-t/\tau}) to find the charge at t=10.0 st = 10.0\text{ s}.

You correctly determined the initial maximum current I0=ERI_0 = \frac{\mathcal{E}}{R}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Selection Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating quantities that grow from zero with quantities that decay from an initial maximum during capacitor charging. In an RC charging circuit, charge q(t)q(t) and capacitor voltage VC(t)V_C(t) start at zero and rise toward maximum using (1−e−t/τ)(1 - e^{-t/\tau}), whereas current i(t)i(t) and resistor voltage VR(t)V_R(t) start at a maximum and decay toward zero using e−t/τe^{-t/\tau}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Charging Behavior of Current vs. Charge
  • When charging an uncharged capacitor, charge accumulates from zero via (1−e−t/τ)(1 - e^{-t/\tau}), while current starts at maximum and drops via e−t/τe^{-t/\tau}.

  • Always verify boundary values: at t=0t = 0, i(0)=I0i(0) = I_0; at t→∞t \to \infty, i(∞)=0i(\infty) = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the current decay equation for an RC charging circuit: i(t)=I0e−t/τi(t) = I_0 e^{-t/\tau}.

  2. Evaluate the decay factor at t=10.0 st = 10.0\text{ s}: e−10.0/7.05=e−1.4184≈0.2421e^{-10.0/7.05} = e^{-1.4184} \approx 0.2421.

  3. Multiply by the initial current: i(10.0 s)=(8.00×10−5 A)(0.2421)≈1.94×10−5 Ai(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A})(0.2421) \approx 1.94 \times 10^{-5}\text{ A} (or 19.4 μA19.4\text{ }\mu\text{A}).

Final answer

(a) τ=7.05 s\tau = 7.05\text{ s}; (b) q=4.27×10−4 Cq = 4.27 \times 10^{-4}\text{ C} (427 μC427\text{ }\mu\text{C}), i=1.94×10−5 Ai = 1.94 \times 10^{-5}\text{ A} (19.4 μA19.4\text{ }\mu\text{A})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how Kirchhoff's loop rule E−iR−qC=0\mathcal{E} - iR - \frac{q}{C} = 0 dictates that as q(t)q(t) increases, i(t)i(t) must decrease.

  • Practice checking the t=0t = 0 and t→∞t \to \infty limits of your formula before computing values.

OverviewACEpath Teacher's Diagnosis

03 The student fails to convert the metric prefixes micro (10⁻⁶) and kilo (10³) to base SI units, resulting in an incorrect time constant and subsequent incorrect values.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=RC=150⋅47.0=7050 s\tau = RC = 150 \cdot 47.0 = 7050\text{ s}

    Correct

    τ=RC=(150×103 Ω)(47.0×10−6 F)=7.05 s\tau = RC = (150 \times 10^3\text{ }\Omega)(47.0 \times 10^{-6}\text{ F}) = 7.05\text{ s}

    You multiplied the raw numerical values without converting 150 kΩ150\text{ k}\Omega and 47.0 μF47.0\text{ }\mu\text{F} into base SI units (Ω\Omega and F\text{F}). Because 103×10−6=10−310^3 \times 10^{-6} = 10^{-3}, the correct time constant is 7.05 s7.05\text{ s}.

  2. Step 2

    Qmax⁡=CV=(47.0×10−6 F)(12.0 V)=5.64×10−4 CQ_{\max} = CV = (47.0 \times 10^{-6}\text{ F})(12.0\text{ V}) = 5.64 \times 10^{-4}\text{ C}

  3. Step 3

    q(10.0 s)=(5.64×10−4 C)(1−e−10.07050)=8.00×10−7 Cq(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C})\left(1 - e^{-\frac{10.0}{7050}}\right) = 8.00 \times 10^{-7}\text{ C}

    Correct

    q(10.0 s)=(5.64×10−4 C)(1−e−10.07.05)≈4.27×10−4 Cq(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C})\left(1 - e^{-\frac{10.0}{7.05}}\right) \approx 4.27 \times 10^{-4}\text{ C}

    You applied the charging equation correctly, but using τ=7050 s\tau = 7050\text{ s} instead of 7.05 s7.05\text{ s} led to an incorrect numerical result.

  4. Step 4

    I0=12.0 V150×103 Ω=8.00×10−5 AI_0 = \frac{12.0\text{ V}}{150 \times 10^3\text{ }\Omega} = 8.00 \times 10^{-5}\text{ A}

  5. Step 5

    i(10.0 s)=(8.00×10−5 A)⋅e−10.07050=7.99×10−5 Ai(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A}) \cdot e^{-\frac{10.0}{7050}} = 7.99 \times 10^{-5}\text{ A}

    Correct

    i(10.0 s)=(8.00×10−5 A)⋅e−10.07.05≈1.94×10−5 Ai(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A}) \cdot e^{-\frac{10.0}{7.05}} \approx 1.94 \times 10^{-5}\text{ A}

    You correctly set up the decaying exponential current equation, but substituting τ=7050 s\tau = 7050\text{ s} affected your final answer.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the exact physical formulas for RCRC circuit charging dynamics: q(t)=Qmax⁡(1−e−t/τ)q(t) = Q_{\max}(1 - e^{-t/\tau}) and i(t)=I0e−t/τi(t) = I_0 e^{-t/\tau}.

You correctly used SI base units when finding both Qmax⁡Q_{\max} and I0I_0 independently.

You carried through your calculations with clean mathematical presentation and accurate arithmetic based on your intermediate values.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix omission in time constant calculation

You actually had 7.05 s7.05\text{ s} initially, but crossed it out in favor of 7050 s7050\text{ s} after multiplying 150150 by 47.047.0 without their powers of ten.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You omitted metric prefix multipliers (k=103\text{k} = 10^3 and μ=10−6\mu = 10^{-6}) when computing the product RCRC, forgetting that seconds (s\text{s}) only emerge when resistance is in ohms (Ω\Omega) and capacitance is in farads (F\text{F}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert All Component Values to Base SI Units First
  • 1 kΩ=103 Ω1\text{ k}\Omega = 10^3\text{ }\Omega and 1 μF=10−6 F1\text{ }\mu\text{F} = 10^{-6}\text{ F}. Time in seconds requires ohms and farads: 1 Ω×1 F=1 s1\text{ }\Omega \times 1\text{ F} = 1\text{ s}.

  • Always write down (150×103 Ω)(47.0×10−6 F)(150 \times 10^3\text{ }\Omega)(47.0 \times 10^{-6}\text{ F}) with explicit exponential powers before multiplying.

Use the Kilohm-Microfarad Shortcut Reliably
  • kilo×micro=103×10−6=10−3=milli\text{kilo} \times \text{micro} = 10^3 \times 10^{-6} = 10^{-3} = \text{milli}. Therefore, (kΩ)×(μF)=10−3 s=ms(\text{k}\Omega) \times (\mu\text{F}) = 10^{-3}\text{ s} = \text{ms}.

  • If you multiply the numbers directly without powers of ten (150×47.0=7050150 \times 47.0 = 7050), recognize that the unit is milliseconds (ms\text{ms}), so 7050 ms=7.05 s7050\text{ ms} = 7.05\text{ s}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate τ\tau: τ=RC=(150×103 Ω)(47.0×10−6 F)=7.05 s\tau = RC = (150 \times 10^3\text{ }\Omega)(47.0 \times 10^{-6}\text{ F}) = 7.05\text{ s}.

  2. Compute the exponent at t=10.0 st = 10.0\text{ s}: tτ=10.0 s7.05 s≈1.4184\frac{t}{\tau} = \frac{10.0\text{ s}}{7.05\text{ s}} \approx 1.4184.

  3. Evaluate e−t/τ=e−1.4184≈0.2421e^{-t/\tau} = e^{-1.4184} \approx 0.2421.

  4. Calculate charge q(10.0 s)=(5.64×10−4 C)(1−0.2421)=(5.64×10−4 C)(0.7579)≈4.27×10−4 Cq(10.0\text{ s}) = (5.64 \times 10^{-4}\text{ C})(1 - 0.2421) = (5.64 \times 10^{-4}\text{ C})(0.7579) \approx 4.27 \times 10^{-4}\text{ C} (or 427 μC427\text{ }\mu\text{C}).

  5. Calculate current i(10.0 s)=(8.00×10−5 A)(0.2421)≈1.94×10−5 Ai(10.0\text{ s}) = (8.00 \times 10^{-5}\text{ A})(0.2421) \approx 1.94 \times 10^{-5}\text{ A} (or 19.4 μA19.4\text{ }\mu\text{A}).

Final answer

(a) τ=7.05 s\tau = 7.05\text{ s}; (b) q(10.0 s)=4.27×10−4 Cq(10.0\text{ s}) = 4.27 \times 10^{-4}\text{ C}, i(10.0 s)=1.94×10−5 Ai(10.0\text{ s}) = 1.94 \times 10^{-5}\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out standard scientific notation for all circuit components before multiplying them together.

  • Review the dimensional unit product: (kΩ)×(μF)=103×10−6 s=10−3 s(\text{k}\Omega) \times (\mu\text{F}) = 10^3 \times 10^{-6}\text{ s} = 10^{-3}\text{ s}.

  • Perform a quick physical sanity check: t=10.0 st = 10.0\text{ s} is greater than one time constant (7.05 s7.05\text{ s}), so the capacitor must be more than 63%63\% charged, whereas your value gave less than 1%1\%.

Lock it in

Similar question

01

A 20.0 μF20.0\text{ }\mu\text{F} capacitor is connected in series with a 50.0 kΩ50.0\text{ k}\Omega resistor and a 10.0 V10.0\text{ V} DC supply. If the capacitor is uncharged at t=0 st = 0\text{ s}, calculate the charge on the capacitor at t=1.00 st = 1.00\text{ s}.

Answer

q=1.26×10−4 Cq = 1.26 \times 10^{-4}\text{ C} (or 126 μC126\text{ }\mu\text{C}). Key steps: τ=RC=(50.0×103 Ω)(20.0×10−6 F)=1.00 s\tau = RC = (50.0 \times 10^3\text{ }\Omega)(20.0 \times 10^{-6}\text{ F}) = 1.00\text{ s}. Qmax=CE=2.00×10−4 CQ_{\text{max}} = C\mathcal{E} = 2.00 \times 10^{-4}\text{ C}. At t=τt = \tau, q(τ)=Qmax(1−e−1)=(2.00×10−4)(0.6321)≈1.26×10−4 Cq(\tau) = Q_{\text{max}}(1 - e^{-1}) = (2.00 \times 10^{-4})(0.6321) \approx 1.26 \times 10^{-4}\text{ C}.

02

An uncharged capacitor charges through a resistor from a 9.0 V9.0\text{ V} battery. How many time constants τ\tau must elapse before the voltage across the capacitor reaches 8.0 V8.0\text{ V}?

Answer

t≈2.20 τt \approx 2.20\,\tau. Key steps: VC(t)=E(1−e−t/τ)  ⟹  8.0=9.0(1−e−t/τ)  ⟹  e−t/τ=19  ⟹  t/τ=−ln⁡(1/9)=ln⁡(9)≈2.20V_C(t) = \mathcal{E}(1 - e^{-t/\tau}) \implies 8.0 = 9.0(1 - e^{-t/\tau}) \implies e^{-t/\tau} = \frac{1}{9} \implies t/\tau = -\ln(1/9) = \ln(9) \approx 2.20.

03

A 10.0 μF10.0\text{ }\mu\text{F} capacitor is charged to a potential of 24.0 V24.0\text{ V} and then disconnected from the source. At t=0 st = 0\text{ s}, it is connected across a 200 kΩ200\text{ k}\Omega resistor to discharge. Determine the remaining charge and the current at t=4.0 st = 4.0\text{ s}.

Answer

q(4.0 s)=3.25×10−5 Cq(4.0\text{ s}) = 3.25 \times 10^{-5}\text{ C} (or 32.5 μC32.5\text{ }\mu\text{C}); i(4.0 s)=1.62×10−5 Ai(4.0\text{ s}) = 1.62 \times 10^{-5}\text{ A} (or 16.2 μA16.2\text{ }\mu\text{A}). Key steps: τ=RC=(2.00×105 Ω)(1.00×10−5 F)=2.00 s\tau = RC = (2.00 \times 10^5\text{ }\Omega)(1.00 \times 10^{-5}\text{ F}) = 2.00\text{ s}. Q0=CV0=2.40×10−4 CQ_0 = CV_0 = 2.40 \times 10^{-4}\text{ C}. For discharging, q(t)=Q0e−t/τ=(2.40×10−4)e−4.0/2.0=(2.40×10−4)e−2≈3.25×10−5 Cq(t) = Q_0 e^{-t/\tau} = (2.40 \times 10^{-4})e^{-4.0/2.0} = (2.40 \times 10^{-4})e^{-2} \approx 3.25 \times 10^{-5}\text{ C}. Current i(t)=VC(t)R=q(t)RC=3.25×10−52.00≈1.62×10−5 Ai(t) = \frac{V_C(t)}{R} = \frac{q(t)}{RC} = \frac{3.25 \times 10^{-5}}{2.00} \approx 1.62 \times 10^{-5}\text{ A}.

Loading workspace…