Resources

A student models the drag force acting on an underwater autonomous vehicle moving at speed vv using the proposed formula Fdrag=12CdρaAbvcF_{\text{drag}} = \frac{1}{2} C_d \rho^a A^b v^c, where CdC_d is a dimensionless drag coefficient, ρ\rho is the fluid density (in kg/m3\text{kg}/\text{m}^3), AA is the projected frontal cross-sectional area (in m2\text{m}^2), and vv is the velocity (in m/s\text{m}/\text{s}). (a) Using dimensional analysis, determine the integer powers aa, bb, and cc required for the equation to be dimensionally consistent with a force. (b) For water density ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg}/\text{m}^3, vehicle frontal area A=0.450 m2A = 0.450\text{ m}^2, Cd=0.280C_d = 0.280, and speed v=4.00 m/sv = 4.00\text{ m}/\text{s}, calculate the magnitude of the drag force and state its order of magnitude (as a power of 1010).

Answer and steps

Final answer

(a) a=1a = 1, b=1b = 1, c=2c = 2 (so Fdrag=12CdρAv2F_{\text{drag}} = \frac{1}{2} C_d \rho A v^2); (b) Fdrag=1.01×103 NF_{\text{drag}} = 1.01 \times 10^3\text{ N}, order of magnitude is 103 N10^3\text{ N}.

Steps

Part (a): Dimensional Analysis to Find aa, bb, and cc

  1. Write down the base dimensions for each variable:

    • Force has units of newtons (N=kg⋅m/s2\text{N} = \text{kg}\cdot\text{m}/\text{s}^2), so its dimensions are: [Fdrag]=M L T−2[F_{\text{drag}}] = \text{M}\,\text{L}\,\text{T}^{-2}
    • The drag coefficient CdC_d and the constant factor 12\frac{1}{2} are dimensionless: [Cd]=1[C_d] = 1
    • Fluid density ρ\rho has units of kg/m3\text{kg}/\text{m}^3: [ρ]=M L−3[\rho] = \text{M}\,\text{L}^{-3}
    • Cross-sectional area AA has units of m2\text{m}^2: [A]=L2[A] = \text{L}^2
    • Speed vv has units of m/s\text{m}/\text{s}: [v]=L T−1[v] = \text{L}\,\text{T}^{-1}
  2. Substitute dimensions into the drag force equation: [Fdrag]=[ρ]a[A]b[v]c[F_{\text{drag}}] = [\rho]^a [A]^b [v]^c M1 L1 T−2=(M L−3)a(L2)b(L T−1)c\text{M}^1\,\text{L}^1\,\text{T}^{-2} = (\text{M}\,\text{L}^{-3})^a (\text{L}^2)^b (\text{L}\,\text{T}^{-1})^c M1 L1 T−2=Ma L−3a+2b+c T−c\text{M}^1\,\text{L}^1\,\text{T}^{-2} = \text{M}^a\,\text{L}^{-3a + 2b + c}\,\text{T}^{-c}
  3. Equate powers of mass (M\text{M}), length (L\text{L}), and time (T\text{T}):

    • Mass (M\text{M}): a=1a = 1
    • Time (T\text{T}): −c=−2  ⟹  c=2-c = -2 \implies c = 2
    • Length (L\text{L}): −3a+2b+c=1-3a + 2b + c = 1 Substitute a=1a = 1 and c=2c = 2: −3(1)+2b+2=1  ⟹  2b−1=1  ⟹  2b=2  ⟹  b=1-3(1) + 2b + 2 = 1 \implies 2b - 1 = 1 \implies 2b = 2 \implies b = 1

Thus, the exponents are: a=1,b=1,c=2a = 1, \quad b = 1, \quad c = 2 The dimensionally consistent equation is: Fdrag=12CdρAv2F_{\text{drag}} = \frac{1}{2} C_d \rho A v^2


Part (b): Calculation and Order of Magnitude

  1. Calculate the numerical value of the drag force: Substitute the given values into the formula:

    • ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg/m}^3
    • A=0.450 m2A = 0.450\text{ m}^2
    • Cd=0.280C_d = 0.280
    • v=4.00 m/sv = 4.00\text{ m/s}

    Fdrag=12(0.280)⋅(1.00×103 kg/m3)⋅(0.450 m2)⋅(4.00 m/s)2F_{\text{drag}} = \frac{1}{2} (0.280) \cdot (1.00 \times 10^3\text{ kg/m}^3) \cdot (0.450\text{ m}^2) \cdot (4.00\text{ m/s})^2 Fdrag=0.140⋅1.00×103⋅0.450⋅16.0F_{\text{drag}} = 0.140 \cdot 1.00 \times 10^3 \cdot 0.450 \cdot 16.0 Fdrag=1008 N≈1.01×103 NF_{\text{drag}} = 1008\text{ N} \approx 1.01 \times 10^3\text{ N}

  2. Determine the order of magnitude:

    • In scientific notation, the force is 1.008×103 N1.008 \times 10^3\text{ N}.
    • Since the mantissa 1.0081.008 is less than 10≈3.16\sqrt{10} \approx 3.16 (or 55, depending on the convention; both round to 11), the power of 1010 remains unchanged.
    • Therefore, the order of magnitude is: 103 N10^3\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the velocity when substituting values into the drag force equation, leading to an incorrect force magnitude and order of magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    [F]=MLT−2,[ρ]=ML−3,[A]=L2,[v]=LT−1  ⟹  MLT−2=MaL−3a+2b+cT−c  ⟹  a=1,b=1,c=2[F] = \text{MLT}^{-2}, [\rho] = \text{ML}^{-3}, [A] = \text{L}^2, [v] = \text{LT}^{-1} \implies \text{MLT}^{-2} = \text{M}^a \text{L}^{-3a+2b+c} \text{T}^{-c} \implies a = 1, b = 1, c = 2

  2. Step 2

    Fdrag=12CdρAv=0.5×0.280×1000×0.450×4.00F_{\text{drag}} = \frac{1}{2} C_d \rho A v = 0.5 \times 0.280 \times 1000 \times 0.450 \times 4.00

    Correct

    Fdrag=12CdρAv2=0.5×0.280×1000×0.450×(4.00)2F_{\text{drag}} = \frac{1}{2} C_d \rho A v^2 = 0.5 \times 0.280 \times 1000 \times 0.450 \times (4.00)^2

    In part (a), you found that c=2c = 2, meaning the formula requires v2v^2. When setting up part (b), you wrote vv to the first power instead of squaring the speed.

  3. Step 3

    Fdrag=2.52×102 N  ⟹  Order of magnitude=102 NF_{\text{drag}} = 2.52 \times 10^2\text{ N} \implies \text{Order of magnitude} = 10^2\text{ N}

    Correct

    Fdrag=1.01×103 N  ⟹  Order of magnitude=103 NF_{\text{drag}} = 1.01 \times 10^3\text{ N} \implies \text{Order of magnitude} = 10^3\text{ N}

    Because you evaluated the velocity as 4.00 m/s4.00\text{ m/s} rather than (4.00 m/s)2=16.0 m2/s2(4.00\text{ m/s})^2 = 16.0\text{ m}^2/\text{s}^2, the resulting value 252 N252\text{ N} and order of magnitude 102 N10^2\text{ N} are off by a factor of 44 from the true values.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly expressed the dimensional formulas for force, density, cross-sectional area, and speed.

You matched powers of dimensions systematically to find a=1a = 1, b=1b = 1, and c=2c = 2.

You correctly extracted the order of magnitude from your calculated scientific notation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Power in Formula Transfer

You dropped the exponent 22 on speed when transitioning from the derived powers in part (a) to the calculation in part (b).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Disconnect between algebraic derivation and numerical substitution: after deriving the exponents symbolically, you transcribed the formula as a linear dependence on velocity rather than carrying forward the verified power vc=v2v^c = v^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Formula Transfer Verification
  • Every variable in an empirical or derived power-law formula must carry its full exponent into the calculation step.

  • Before substituting numbers, explicitly write out the full formula with all derived exponents: Fdrag=12Cdρ1A1v2F_{\text{drag}} = \frac{1}{2} C_d \rho^1 A^1 v^2.

Dimensional Sanity Check of the Answer
  • The units of the numerical calculation must match the target unit (here, kg⋅m/s2=N\text{kg}\cdot\text{m}/\text{s}^2 = \text{N}).

  • Notice that with v1v^1, the units yield (kg/m3)(m2)(m/s)=kg/s(\text{kg}/\text{m}^3)(\text{m}^2)(\text{m}/\text{s}) = \text{kg}/\text{s}, which is not a force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write out the formula with the derived exponents: Fdrag=12CdρAv2F_{\text{drag}} = \frac{1}{2} C_d \rho A v^2.

  2. Substitute the given values: Fdrag=12(0.280)⋅(1.00×103 kg/m3)⋅(0.450 m2)⋅(4.00 m/s)2F_{\text{drag}} = \frac{1}{2} (0.280) \cdot (1.00 \times 10^3\text{ kg/m}^3) \cdot (0.450\text{ m}^2) \cdot (4.00\text{ m/s})^2.

  3. Evaluate the numerical value: Fdrag=0.140×1000×0.450×16.0=1008 N≈1.01×103 NF_{\text{drag}} = 0.140 \times 1000 \times 0.450 \times 16.0 = 1008\text{ N} \approx 1.01 \times 10^3\text{ N}.

  4. Determine the order of magnitude: since 1.008<10≈3.161.008 < \sqrt{10} \approx 3.16, round to the nearest power of ten, giving 103 N10^3\text{ N}.

Final answer

(a) a=1,b=1,c=2a = 1, b = 1, c = 2; (b) Fdrag=1.01×103 NF_{\text{drag}} = 1.01 \times 10^3\text{ N}, order of magnitude is 103 N10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the general formula with its derived powers before substituting numbers.

  • Perform a quick unit cancellation check on your numerical values to make sure the result has dimensions of force (N=kg⋅m/s2\text{N} = \text{kg}\cdot\text{m}/\text{s}^2).

OverviewACEpath Teacher's Diagnosis

02 The student rounds 1.01 × 10³ up to the next power of ten by mistakenly treating any non-zero mantissa as rounding up to 10⁴.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    [F]=MLT−2[F] = \text{M}\text{L}\text{T}^{-2}, [ρ]=ML−3[\rho] = \text{M}\text{L}^{-3}, [A]=L2[A] = \text{L}^2, [v]=LT−1[v] = \text{L}\text{T}^{-1} ⟹\Longrightarrow MLT−2=(ML−3)a(L2)b(LT−1)c\text{M}\text{L}\text{T}^{-2} = (\text{M}\text{L}^{-3})^a (\text{L}^2)^b (\text{L}\text{T}^{-1})^c ⟹\Longrightarrow a=1a = 1, c=2c = 2, −3(1)+2b+2=1  ⟹  b=1-3(1) + 2b + 2 = 1 \implies b = 1

  2. Step 2

    Fdrag=12CdρAv2=0.5×0.280×1000×0.450×4.002=1008 N=1.01×103 NF_{\text{drag}} = \frac{1}{2} C_d \rho A v^2 = 0.5 \times 0.280 \times 1000 \times 0.450 \times 4.00^2 = 1008\text{ N} = 1.01 \times 10^3\text{ N}

  3. Step 3

    Order of magnitude=104 N\text{Order of magnitude} = 10^4\text{ N}

    Correct

    Order of magnitude=103 N\text{Order of magnitude} = 10^3\text{ N}

    When writing a number in scientific notation M×10nM \times 10^n, the order of magnitude rounds to 10n+110^{n+1} only if the mantissa M≥10≈3.16M \ge \sqrt{10} \approx 3.16 (or ≥5\ge 5 under standard rounding). Since 1.01<3.161.01 < 3.16, the mantissa rounds to 11, making the order of magnitude 103 N10^3\text{ N}.

WHAT YOU DID WELL
Compliments from Your Teacher

You set up and solved the dimensional analysis equations for mass, length, and time without any algebraic errors.

You correctly substituted the numerical parameters into the drag force formula to find 1.01×103 N1.01 \times 10^3\text{ N}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Order of magnitude rounding error

You treated any mantissa greater than 11 as rounding up to the next power of ten rather than comparing it against the logarithmic midpoint threshold 10≈3.16\sqrt{10} \approx 3.16.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusion regarding how to determine an order of magnitude from scientific notation M×10nM \times 10^n. An order of magnitude is the power of 1010 closest to the value on a logarithmic scale. A mantissa of 1.011.01 is much closer to 100=110^0 = 1 than to 101=1010^1 = 10, so the exponent does not increase.

REASONING PATH
Your ACEpath teacher’s suggested approach
Evaluate the Mantissa
  • For a value in scientific notation M×10nM \times 10^n, compare MM against the threshold 10≈3.16\sqrt{10} \approx 3.16 (or 55).

  • Check if M<3.16M < 3.16. If M<3.16M < 3.16, round MM to 100=110^0 = 1, giving order of magnitude 10n10^n. If M≥3.16M \ge 3.16, round MM to 101=1010^1 = 10, giving order of magnitude 10n+110^{n+1}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the scientific notation components: mantissa M=1.01M = 1.01 and exponent n=3n = 3.

  2. Compare M=1.01M = 1.01 with the logarithmic boundary 10≈3.16\sqrt{10} \approx 3.16. Since 1.01<3.161.01 < 3.16, 1.011.01 rounds to 100=110^0 = 1.

  3. Combine with the base power: 1×103 N=103 N1 \times 10^3\text{ N} = 10^3\text{ N}.

Final answer

Order of magnitude is 103 N10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review order-of-magnitude rules on a logarithmic number line, noting that 100.5=10≈3.16210^{0.5} = \sqrt{10} \approx 3.162 is the midpoint between 10010^0 and 10110^1.

  • Practice converting values like 2.8×1052.8 \times 10^5, 4.2×10−24.2 \times 10^{-2}, and 8.9×1038.9 \times 10^3 to their orders of magnitude.

OverviewACEpath Teacher's Diagnosis

03 The student misidentifies the dimensions of force as M L² T⁻² by confusing force with energy or work, resulting in an incorrect exponent b = 3/2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    [F]=M L2 T−2[F] = \text{M}\,\text{L}^2\,\text{T}^{-2}, [ρ]=M L−3[\rho] = \text{M}\,\text{L}^{-3}, [A]=L2[A] = \text{L}^2, [v]=L T−1[v] = \text{L}\,\text{T}^{-1}

    Correct

    [F]=M L T−2[F] = \text{M}\,\text{L}\,\text{T}^{-2}, [ρ]=M L−3[\rho] = \text{M}\,\text{L}^{-3}, [A]=L2[A] = \text{L}^2, [v]=L T−1[v] = \text{L}\,\text{T}^{-1}

    You correctly stated the dimensions for density, area, and speed, but force has dimensions of mass times acceleration, [F]=[m][a]=M L T−2[F] = [m][a] = \text{M}\,\text{L}\,\text{T}^{-2}. The expression M L2 T−2\text{M}\,\text{L}^2\,\text{T}^{-2} represents energy or work.

  2. Step 2

    M L2 T−2=Ma L−3a+2b+c T−c  ⟹  a=1,c=2,−3(1)+2b+2=2  ⟹  b=32\text{M}\,\text{L}^2\,\text{T}^{-2} = \text{M}^a\,\text{L}^{-3a+2b+c}\,\text{T}^{-c} \implies a=1, c=2, -3(1)+2b+2=2 \implies b=\frac{3}{2}

    Correct

    M L T−2=Ma L−3a+2b+c T−c  ⟹  a=1,c=2,−3(1)+2b+2=1  ⟹  b=1\text{M}\,\text{L}\,\text{T}^{-2} = \text{M}^a\,\text{L}^{-3a+2b+c}\,\text{T}^{-c} \implies a=1, c=2, -3(1)+2b+2=1 \implies b=1

    Your system-solving technique was mathematically sound, but because the length exponent on the left-hand side was set to 22 instead of 11, you obtained b=32b = \frac{3}{2} instead of b=1b = 1.

  3. Step 3

    Fdrag=12Cdρ1A3/2v2=0.5×0.280×1000×0.4501.5×4.002=676 NF_{\text{drag}} = \frac{1}{2} C_d \rho^1 A^{3/2} v^2 = 0.5 \times 0.280 \times 1000 \times 0.450^{1.5} \times 4.00^2 = 676\text{ N}

    Correct

    Fdrag=12CdρAv2=0.5×0.280×1000×0.450×4.002≈1.01×103 NF_{\text{drag}} = \frac{1}{2} C_d \rho A v^2 = 0.5 \times 0.280 \times 1000 \times 0.450 \times 4.00^2 \approx 1.01 \times 10^3\text{ N}

    You substituted the given numerical values and evaluated the arithmetic carefully, but using the exponent b=32b = \frac{3}{2} led to 676 N676\text{ N} rather than the correct value of 1008 N≈1.01×103 N1008\text{ N} \approx 1.01 \times 10^3\text{ N}.

  4. Step 4

    Order of magnitude=103 N\text{Order of magnitude} = 10^3\text{ N}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived the dimensional formula for the right-hand side as Ma L−3a+2b+c T−c\text{M}^a\,\text{L}^{-3a+2b+c}\,\text{T}^{-c}.

You solved the linear system for the exponents aa, bb, and cc with correct algebraic steps.

You carried out the numerical substitution and power-of-ten rounding accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Dimensions of Force

You wrote M L2 T−2\text{M}\,\text{L}^2\,\text{T}^{-2} instead of M L T−2\text{M}\,\text{L}\,\text{T}^{-2} for force, accidentally using the base dimensions of work or energy.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the base dimensions of force (F=maF = ma, so kg⋅m/s2\text{kg}\cdot\text{m}/\text{s}^2) with those of energy or work (W=FdW = Fd, so kg⋅m2/s2\text{kg}\cdot\text{m}^2/\text{s}^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Reconstruct from Newton's Second Law
  • F=ma  ⟹  [F]=[m][a]=M⋅(L T−2)=M L T−2F = ma \implies [F] = [m][a] = \text{M} \cdot (\text{L}\,\text{T}^{-2}) = \text{M}\,\text{L}\,\text{T}^{-2}

  • Whenever you need the dimensions of force, derive them quickly from F=maF = ma to avoid confusing them with energy.

Distinguish Force from Energy/Work
  • [Work]=[F][d]=(M L T−2)(L)=M L2 T−2[\text{Work}] = [F][d] = (\text{M}\,\text{L}\,\text{T}^{-2})(\text{L}) = \text{M}\,\text{L}^2\,\text{T}^{-2}

  • Check the power of length: force has length to the first power (L1\text{L}^1), while energy has length squared (L2\text{L}^2).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set [F]=M L T−2[F] = \text{M}\,\text{L}\,\text{T}^{-2}.

  2. Equate powers of fundamental dimensions: M:a=1\text{M}: a = 1; T:−c=−2  ⟹  c=2\text{T}: -c = -2 \implies c = 2; L:−3a+2b+c=1\text{L}: -3a + 2b + c = 1.

  3. Substitute a=1a = 1 and c=2c = 2 into the length equation: −3(1)+2b+2=1  ⟹  2b−1=1  ⟹  2b=2  ⟹  b=1-3(1) + 2b + 2 = 1 \implies 2b - 1 = 1 \implies 2b = 2 \implies b = 1.

  4. Write the final formula: Fdrag=12CdρAv2F_{\text{drag}} = \frac{1}{2} C_d \rho A v^2.

  5. Calculate Fdrag=12(0.280)(1.00×103)(0.450)(4.00)2=1008 N≈1.01×103 NF_{\text{drag}} = \frac{1}{2}(0.280)(1.00 \times 10^3)(0.450)(4.00)^2 = 1008\text{ N} \approx 1.01 \times 10^3\text{ N}.

Final answer

(a) a=1,b=1,c=2a = 1, b = 1, c = 2; (b) Fdrag≈1.01×103 NF_{\text{drag}} \approx 1.01 \times 10^3\text{ N}, order of magnitude 103 N10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice reconstructing base SI units for derived mechanical quantities (FF, PP, EE, pp) directly from fundamental formulas.

  • Perform a quick sanity check on dimensions: ensure force contains only L1\text{L}^1, while work and energy contain L2\text{L}^2.

Lock it in

Similar question

01

The lift force on an aircraft wing is modeled as FL=12CLρxAyvzF_L = \frac{1}{2} C_L \rho^x A^y v^z. (a) State the values of x,y,zx, y, z based on dimensional consistency. (b) If CL=0.50C_L = 0.50, ρ=1.20 kg/m3\rho = 1.20\text{ kg/m}^3, A=20.0 m2A = 20.0\text{ m}^2, and v=50.0 m/sv = 50.0\text{ m/s}, calculate the lift force.

Answer

(a) x=1x = 1, y=1y = 1, z=2z = 2 (lift has dimensions of force, identical to aerodynamic drag). (b) FL=12(0.50)(1.20)(20.0)(50.0)2=0.30×20.0×2500=15 000 N=1.50×104 NF_L = \frac{1}{2} (0.50) (1.20) (20.0) (50.0)^2 = 0.30 \times 20.0 \times 2500 = 15\,000\text{ N} = 1.50 \times 10^4\text{ N}.

02

The rate of kinetic energy delivery (power) by wind through a wind turbine of swept area AA is modeled as P=12ρApvqP = \frac{1}{2} \rho A^p v^q. (a) Using dimensional analysis with [P]=ML2T−3[P] = \text{M}\text{L}^2\text{T}^{-3}, find powers pp and qq. (b) For air density ρ=1.25 kg/m3\rho = 1.25\text{ kg/m}^3, area A=80.0 m2A = 80.0\text{ m}^2, and wind speed v=10.0 m/sv = 10.0\text{ m/s}, calculate the available wind power and its order of magnitude.

Answer

(a) [P]=ML2T−3=(ML−3)(L2)p(LT−1)q=ML2p+q−3T−q[P] = \text{M}\text{L}^2\text{T}^{-3} = (\text{M}\text{L}^{-3})(\text{L}^2)^p (\text{L}\text{T}^{-1})^q = \text{M}\text{L}^{2p+q-3}\text{T}^{-q}. Matching time: −q=−3  ⟹  q=3-q = -3 \implies q = 3. Matching length: 2p+3−3=2  ⟹  p=12p + 3 - 3 = 2 \implies p = 1. (b) P=12(1.25)(80.0)(10.0)3=50.0×1000=5.00×104 WP = \frac{1}{2} (1.25) (80.0) (10.0)^3 = 50.0 \times 1000 = 5.00 \times 10^4\text{ W}. Since 5.00>10≈3.165.00 > \sqrt{10} \approx 3.16, the order of magnitude is 105 W10^5\text{ W}.

03

A spherical particle of radius rr moving slowly at speed vv through a viscous fluid experiences Stokes drag F=6πηarbvcF = 6\pi \eta^a r^b v^c, where dynamic viscosity η\eta has dimensions ML−1T−1\text{M}\text{L}^{-1}\text{T}^{-1}. (a) Determine aa, bb, and cc. (b) A spherical bead of radius r=1.00 mmr = 1.00\text{ mm} falls at v=2.00×10−2 m/sv = 2.00\times 10^{-2}\text{ m/s} in oil with η=0.150 Pa⋅s\eta = 0.150\text{ Pa}\cdot\text{s}. Compute the drag force and state its order of magnitude.

Answer

(a) MLT−2=(ML−1T−1)a(L)b(LT−1)c=MaL−a+b+cT−a−c\text{M}\text{L}\text{T}^{-2} = (\text{M}\text{L}^{-1}\text{T}^{-1})^a (\text{L})^b (\text{L}\text{T}^{-1})^c = \text{M}^a \text{L}^{-a+b+c} \text{T}^{-a-c}. Matching mass gives a=1a = 1; matching time gives −1−c=−2  ⟹  c=1-1-c = -2 \implies c = 1; matching length gives −1+b+1=1  ⟹  b=1-1+b+1 = 1 \implies b = 1. Thus a=1,b=1,c=1a=1, b=1, c=1. (b) F=6π(0.150 Pa⋅s)(1.00×10−3 m)(2.00×10−2 m/s)=5.65×10−5 NF = 6\pi (0.150\text{ Pa}\cdot\text{s}) (1.00 \times 10^{-3}\text{ m}) (2.00 \times 10^{-2}\text{ m/s}) = 5.65 \times 10^{-5}\text{ N}. Since 5.65>105.65 > \sqrt{10}, the order of magnitude is 10−4 N10^{-4}\text{ N}.

Loading workspace…