Resources
A student pushes a heavy crate of mass across a rough horizontal warehouse floor () over a total horizontal distance . In Route 1, the student pushes the crate in a single continuous straight line from rest to final rest, where the crate reaches a peak speed at the midpoint before decelerating. In Route 2, the student pushes the crate along an S-shaped meandering path of total path length between the same initial and final positions, reaching an identical peak speed before coming to rest. Intuition often leads students to assume both routes require equal work because the displacement between endpoints is identical. (a) Calculate the total thermal energy generated by friction along Route 1 () versus Route 2 (). (b) Explain why mechanical energy conservation cannot be expressed purely in terms of state coordinates for this system. (Use .)
Answer and steps
Final answer
(a) , ; (b) Friction is a non-conservative, path-dependent force whose cumulative work depends on the integral of arc length , not on spatial displacement.
Steps
Part (a): Calculating Thermal Energy Generated by Friction
-
Determine the Magnitude of Kinetic Friction On a level horizontal surface with no vertical applied forces, the normal force balances gravity:
The magnitude of the kinetic friction force is constant along the motion:
Substitute the given values (, , ):
-
Compute Thermal Energy for Route 1 Friction always opposes the instantaneous direction of motion, so the thermal energy dissipated over any path of total distance (arc length) is:
For Route 1, the crate travels in a straight line, so the path length equals the displacement magnitude:
- Compute Thermal Energy for Route 2 For the curved Route 2, the total distance traveled along the floor is :
Part (b): Why Mechanical Energy Cannot Be Expressed by State Coordinates Alone
- Conservative vs. Non-Conservative Forces: For conservative forces (such as gravity or ideal spring forces), the work done depends only on the initial and final positions (state coordinates and ). As a result, a scalar potential energy function can be defined such that .
-
Path Dependence of Friction: Kinetic friction is a non-conservative force that opposes instantaneous velocity at every point along the trajectory. The work done by friction along a path is given by the line integral:
Because is proportional to the total arc length rather than the net displacement vector , two paths sharing the exact same endpoint coordinates produce entirely different energy transformations. Therefore, energy dissipated by friction cannot be expressed as a function of the system's state coordinates alone.
Common Pitfall: Conflating displacement () with total distance traveled (). While conservative work depends on net displacement, work done by friction accumulates continuously over the actual trajectory length.
Typical errors
01 The student treats friction as a conservative force depending only on net displacement rather than total path length, calculating equal thermal energy for both routes.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
Displacement for both routes is
- Step 3Correct
You used the straight-line displacement instead of the total path length . Because kinetic friction continuously opposes the instantaneous velocity along the curved trajectory, thermal energy dissipation accumulates over the entire arc length.
- Step 4
Friction depends on initial and final positions, so mechanical energy depends only on endpoint state coordinates.
CorrectKinetic friction is a non-conservative, path-dependent force whose work is given by . Because work accumulates along the total path length rather than depending solely on initial and final position coordinates , mechanical energy cannot be expressed purely in terms of state coordinates.
You concluded that friction depends only on initial and final positions. In reality, friction is non-conservative and path-dependent, so its cumulative work cannot be represented as a state function or potential energy difference.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the normal force and calculated the constant kinetic friction force magnitude as .
You correctly solved for the thermal energy dissipated over the straight-line motion in Route 1.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated path-independent conservative forces with path-dependent non-conservative forces, incorrectly assuming that friction work depends only on net displacement rather than total path length.
REASONING PATH
Your ACEpath teacher’s suggested approach- Work of Non-Conservative Forces
For friction on a horizontal plane, , where is the actual path length, not the straight-line displacement .
Always integrate along the actual trajectory when calculating work done by non-conservative forces such as friction or air drag.
- State Coordinates vs. Path History
A potential energy function can only be defined for conservative forces where .
Recognize that non-conservative dissipation cannot be tracked solely by start and end points; it requires knowledge of the complete path history.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the actual path length for Route 2: .
Multiply the constant friction force by the path length: .
State the conceptual distinction for part (b): kinetic friction is non-conservative because always opposes instantaneous motion, meaning depends on the total distance traveled, making it impossible to write energy conservation solely in terms of state coordinates.
(a) , ; (b) Friction is non-conservative and path-dependent, so its work depends on total arc length rather than endpoint coordinates.
02 The student incorrectly adds kinetic energy from the peak speed to the thermal energy generated by friction.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You added to the thermal dissipation. Because the crate starts at rest and ends at rest, the total thermal energy dissipated by friction over the entire trajectory is simply , where is the total path length. Any kinetic energy gained during the motion is completely converted to thermal energy as the crate decelerates to rest, so adding double counts that energy.
- Step 4
Energy is lost as thermal energy due to friction along the path, which depends on path length rather than state coordinates alone, so it cannot be modeled by potential energy coordinates.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the magnitude of the kinetic friction force on the level floor.
You correctly identified that thermal dissipation depends on the total path length rather than endpoint displacement alone in Part (b).
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the peak kinetic energy as an additional, separate energy sink instead of recognizing that kinetic energy is an internal intermediate state that dissipates entirely back into thermal energy as the object comes to rest.
REASONING PATH
Your ACEpath teacher’s suggested approach- Thermal Energy from Friction
For a constant magnitude of kinetic friction opposing motion along a path of total arc length , the thermal energy generated is .
Multiply friction magnitude directly by total distance traveled; do not add intermediate kinetic energy terms.
- Overall Energy Accounting (Rest to Rest)
When initial and final velocities are both zero, .
Recognize that all intermediate kinetic energy has already returned to zero at the final state and was dissipated through friction during deceleration.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the direct relation for thermal energy generated by friction over total distance traveled: .
For Route 1, substitute : .
For Route 2, substitute : .
(a) , ; (b) Friction is a non-conservative, path-dependent force whose cumulative work depends on total arc length rather than endpoint displacement.
Lock it in
What distinguishes a conservative force from a non-conservative force in terms of work?
A conservative force does work that depends only on the endpoints (path-independent), whereas a non-conservative force (like friction) does work that depends on the actual path length traveled.
Similar question
A block is pushed along a horizontal surface (, ) around a complete circular loop of radius , returning to its starting point. Calculate the total work done by friction.
Answer
. The friction force magnitude is . The total distance traveled around the circle is . Because friction always opposes motion, (even though displacement is zero).
An object moves from to under gravity ( downward along the y-axis) and kinetic friction (). Path A is a straight line of length . Path B consists of two segments: along the x-axis to then parallel to the y-axis to . Compare the work done by gravity and the work done by friction along both paths.
Answer
For gravity (conservative): for both paths, because it depends only on the change in vertical state coordinate . For friction (non-conservative): Path A has , giving ; Path B has , giving .
A crate slides along a horizontal track from to . The coefficient of kinetic friction varies with position as . Express the total thermal energy generated over this straight-line displacement in terms of , , , and , and state whether this friction force can be associated with a potential energy function.
Answer
. Friction varies with position: . The work magnitude is . Although is a function of position here, it still cannot be associated with a potential energy function because reversing direction reverses the force vector (it always opposes ), so the loop integral .