Resources
An industrial pressure gauge records a hydrostatic head in non-standard engineering units of (pounds-force per square inch, psi). Given the exact definitions and : (a) Convert this pressure directly into the SI derived unit of pascals (), expressing the result to three significant figures. (b) Express the resulting pressure entirely in SI base units.
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Converting to Pascals ()
Pressure is defined as force per unit area:
The given non-standard value is . To convert this into the SI derived unit of pascals (), apply unit conversion factors for force and area:
- Convert force from to :
-
Convert area from to :
Common Pitfall: Remember to square the length conversion factor when converting units of area; forgetting to square is a frequent mistake.
-
Substitute the conversion factors into the pressure expression:
Since , and the initial value has three significant figures, round the result to three significant figures:
Part (b): Expressing in SI Base Units
The derived SI unit for pressure is the pascal (), which is defined as:
According to Newton's second law (), the derived unit of force (newton, ) can be broken down into SI base units (, , and ):
Substitute this definition into the expression for pressure:
Multiplying by the numerical value from part (a):
Typical errors
01 The student forgets to square the linear conversion factor when converting from square inches to square meters in the denominator, resulting in a value that is too small by a factor of 0.0254.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used the linear factor in the denominator instead of squaring it. Because pressure is force per unit area, equals .
- Step 2Correct
Your numerical value of directly resulted from dividing by rather than .
- Step 3
- Step 4Correct
The base units are correct, but the numerical coefficient propagates the error from part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the given conversion factor to convert the force component.
You correctly related newtons to fundamental base units using .
You accurately derived that in SI base units.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by the linear conversion factor instead of squaring it for square inches.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated an area unit conversion as a linear unit conversion. When converting derived units with powers (such as area or volume ), the entire linear conversion factor must be raised to that same power: .
REASONING PATH
Your ACEpath teacher’s suggested approach- Area and Volume Unit Scaling
For any linear conversion , the area relation is and the volume relation is .
Wrap the complete conversion factor inside parentheses and apply the exponent to both the number and the unit: .
CORRECTED PATH
ACEpath Teacher's DemonstrationSquare the length factor in the denominator: .
Compute the ratio: .
Round to three significant figures: .
Combine the corrected coefficient with your verified base-unit breakdown: .
(a) ; (b)
02 The student multiplies by the conversion factor for area instead of dividing by it because inches are in the denominator of pressure, resulting in an incorrect conversion.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied by instead of dividing by it. Since square inches appear in the denominator of , canceling requires placing in the numerator and in the denominator.
- Step 2Correct
This result follows correctly from multiplying by , but is incorrect due to the inverted denominator conversion in Step 1.
- Step 3Correct
You correctly expressed the pascal in SI base units as , but the numerical value carries over the error from part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the conversion factor to convert force.
You correctly remembered to square the linear conversion factor when working with area.
You correctly derived that in SI base units.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the conversion factor for a denominator unit as a direct multiplier instead of setting up explicit fraction cancellation where the unit in the denominator cancels with the same unit in the numerator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Denominator Unit Cancellation
When converting a unit in the denominator, the conversion fraction must place the original unit in the numerator so that it cancels out: .
Always write full unit fractions with cancellation slashes before multiplying or dividing numerical values.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the dimensional analysis ratio:
Group the numerical calculation:
Round part (a) to three significant figures:
Substitute to complete part (b):
(a) ; (b)
03 The student confuses the definition of the newton as kg·m²/s² instead of kg·m/s², mistakenly using the units of energy rather than force.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You defined the newton as , which is the SI base unit definition of a joule (energy), rather than from Newton's second law ().
- Step 3Correct
You correctly divided your unit definition by , but because the base unit for force was incorrect in the previous step, the final unit for pressure became instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly set up and calculated the numerical conversion from psi to pascals.
You properly squared the length conversion factor when converting square inches to square meters.
You rounded your numerical value correctly to three significant figures.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote for the newton instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the SI base unit expression for force (, giving ) with that for work or energy (, giving ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Deriving Units from Defining Formulas
Base units for any derived unit should come directly from a defining physical law, such as for force.
Always recall to write before substituting into pressure or stress equations.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse Newton's second law () to express in SI base units: .
Substitute this into the definition of pressure (): .
Combine this with the numerical value from part (a): .
(a) ; (b)
Lock it in
When converting an area unit like to , why is it incorrect to multiply by ?
Because is the linear conversion factor; for area, you must square the entire conversion factor: .
Similar question
A hydraulic press exerts a pressure of . Using and , convert this pressure to pascals () rounded to three significant figures.
Answer
. Key steps: .
The shear modulus of a metal rod is . (a) Convert this modulus into pascals (). (b) Express the modulus in SI base units.
Answer
(a) ; (b) . Key steps: ; dividing by scales the value to . Since , the base unit form is identical in magnitude.
An engineering model specifies a dynamic viscosity of . Given and , convert entirely into SI base units () to three significant figures.
Answer
. Key steps: . Converting to base units: , giving .