Resources

In a university physics laboratory, students calibrate an aluminum bomb calorimeter coupled to a continuous-flow electrical dynamometer. A small DC electric motor is powered by an adjustable regulated power supply set at V=18.0 VV = 18.0\text{ V} and I=2.40 AI = 2.40\text{ A}. The motor drives an insulated stirring paddle submerged in an aluminum cup containing water, converting electrical energy into mechanical fluid shear, which subsequently degrades into thermal internal energy via viscous dissipation. The aluminum cup has mass mAl=0.180 kgm_{\text{Al}} = 0.180\text{ kg} (cAl=900 J/(kg⋅K)c_{\text{Al}} = 900\text{ J/(kg}\cdot\text{K)}) and contains mw=0.450 kgm_w = 0.450\text{ kg} of pure water (cw=4.184×103 J/(kg⋅K)c_w = 4.184 \times 10^3\text{ J/(kg}\cdot\text{K)}). Over a run time of Δt=10.0 minutes\Delta t = 10.0\text{ minutes}, the fluid temperature increases from Ti=21.40∘CT_i = 21.40^\circ\text{C} to Tf=29.85∘CT_f = 29.85^\circ\text{C}. Taking the system boundaries as the calorimeter cup and liquid water, calculate: (a) the total electrical input energy EelecE_{\text{elec}}, (b) the thermal energy absorbed by the calorimeter and water QabsorbedQ_{\text{absorbed}}, and (c) the overall electromechanical-to-thermal transfer efficiency η\eta of the experimental apparatus.

Answer and steps

Final answer

(a) Eelec=2.59×104 JE_{\text{elec}} = 2.59 \times 10^4\text{ J}; (b) Qabsorbed=1.73×104 JQ_{\text{absorbed}} = 1.73 \times 10^4\text{ J}; (c) η=66.8%\eta = 66.8\%.

Steps

Part (a): Total Electrical Input Energy (EelecE_{\text{elec}})

The electrical power supplied to the motor is the product of voltage VV and current II:

P=V⋅IP = V \cdot I

Substitute the given electrical parameters:

P=(18.0 V)⋅(2.40 A)=43.2 WP = (18.0\text{ V}) \cdot (2.40\text{ A}) = 43.2\text{ W}

The total time interval in seconds is:

Δt=10.0 min⋅60 s/min=600 s\Delta t = 10.0\text{ min} \cdot 60\text{ s/min} = 600\text{ s}

The total electrical energy supplied is the power multiplied by the duration:

Eelec=P⋅Δt=(43.2 W)⋅(600 s)=25920 J≈2.59×104 JE_{\text{elec}} = P \cdot \Delta t = (43.2\text{ W}) \cdot (600\text{ s}) = 25920\text{ J} \approx 2.59 \times 10^4\text{ J}


Part (b): Thermal Energy Absorbed (QabsorbedQ_{\text{absorbed}})

Both the aluminum cup and the water undergo the same temperature increase:

ΔT=Tf−Ti=29.85∘C−21.40∘C=8.45∘C=8.45 K\Delta T = T_f - T_i = 29.85^\circ\text{C} - 21.40^\circ\text{C} = 8.45^\circ\text{C} = 8.45\text{ K}

The total heat capacity CtotalC_{\text{total}} of the calorimeter cup and water system is:

Ctotal=mAlcAl+mwcwC_{\text{total}} = m_{\text{Al}} c_{\text{Al}} + m_w c_w

Substitute the given masses and specific heat capacities:

CAl=mAlcAl=(0.180 kg)⋅(900 J/(kg⋅K))=162 J/KC_{\text{Al}} = m_{\text{Al}} c_{\text{Al}} = (0.180\text{ kg}) \cdot (900\text{ J/(kg}\cdot\text{K)}) = 162\text{ J/K}

Cw=mwcw=(0.450 kg)⋅(4184 J/(kg⋅K))=1882.8 J/KC_w = m_w c_w = (0.450\text{ kg}) \cdot (4184\text{ J/(kg}\cdot\text{K)}) = 1882.8\text{ J/K}

Ctotal=162 J/K+1882.8 J/K=2044.8 J/KC_{\text{total}} = 162\text{ J/K} + 1882.8\text{ J/K} = 2044.8\text{ J/K}

The heat absorbed by the system is:

Qabsorbed=CtotalΔT=(2044.8 J/K)⋅(8.45 K)=17278.56 J≈1.73×104 JQ_{\text{absorbed}} = C_{\text{total}} \Delta T = (2044.8\text{ J/K}) \cdot (8.45\text{ K}) = 17278.56\text{ J} \approx 1.73 \times 10^4\text{ J}


Part (c): Overall Efficiency (η\eta)

The overall conversion efficiency represents the fraction of input electrical energy successfully converted and stored as internal thermal energy in the calorimeter contents:

η=QabsorbedEelec×100%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} \times 100\%

Using the rounded values to three significant figures (1.73×104 J1.73 \times 10^4\text{ J} and 2.59×104 J2.59 \times 10^4\text{ J}):

η=1.73×104 J2.59×104 J×100%≈66.8%\eta = \frac{1.73 \times 10^4\text{ J}}{2.59 \times 10^4\text{ J}} \times 100\% \approx 66.8\%

(Note: The remaining energy, approximately 33.2%33.2\%, represents losses such as motor electrical and mechanical friction losses and parasitic heat transfer to the ambient surroundings.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the elapsed time from minutes to seconds when calculating electrical energy, resulting in an energy value that is 60 times too small and an impossible efficiency greater than 100%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=V⋅I=18.0 V⋅2.40 A=43.2 WP = V \cdot I = 18.0\text{ V} \cdot 2.40\text{ A} = 43.2\text{ W}

  2. Step 2

    Eelec=P⋅Δt=43.2 W⋅10.0=432 JE_{\text{elec}} = P \cdot \Delta t = 43.2\text{ W} \cdot 10.0 = 432\text{ J}

    Correct

    Eelec=P⋅Δt=(43.2 W)(10.0 min⋅60 s/min)=25920 J≈2.59×104 JE_{\text{elec}} = P \cdot \Delta t = (43.2\text{ W})(10.0\text{ min} \cdot 60\text{ s/min}) = 25920\text{ J} \approx 2.59 \times 10^4\text{ J}

    You multiplied power by 10.010.0 minutes directly without converting to seconds. Because a watt is one joule per second (1 W=1 J/s1\text{ W} = 1\text{ J/s}), time must be expressed in seconds (10.0 min=600 s10.0\text{ min} = 600\text{ s}).

  3. Step 3

    ΔT=29.85∘C−21.40∘C=8.45∘C  ⟹  Ctotal=(0.180)(900)+(0.450)(4184)=162+1882.8=2044.8 J/K  ⟹  Qabsorbed=2044.8 J/K⋅8.45 K=17278.6 J\Delta T = 29.85^\circ\text{C} - 21.40^\circ\text{C} = 8.45^\circ\text{C} \implies C_{\text{total}} = (0.180)(900) + (0.450)(4184) = 162 + 1882.8 = 2044.8\text{ J/K} \implies Q_{\text{absorbed}} = 2044.8\text{ J/K} \cdot 8.45\text{ K} = 17278.6\text{ J}

  4. Step 4

    η=QabsorbedEelec=17278.6 J432 J=40.0=4000%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} = \frac{17278.6\text{ J}}{432\text{ J}} = 40.0 = 4000\%

    Correct

    η=QabsorbedEelec×100%=1.73×104 J2.59×104 J×100%≈66.8%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} \times 100\% = \frac{1.73 \times 10^4\text{ J}}{2.59 \times 10^4\text{ J}} \times 100\% \approx 66.8\%

    Your efficiency ratio setup is correct, but propagating the underestimated input energy from Step 2 produced an impossible efficiency greater than 100%100\%.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the electrical power of the DC motor using P=VIP = VI.

You correctly calculated the combined heat capacity of the aluminum cup and water and found the total thermal energy absorbed.

You correctly identified the efficiency ratio as useful thermal energy divided by total electrical input energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion (Time: Minutes to Seconds)

You substituted Δt=10.0\Delta t = 10.0 directly into E=PΔtE = P \Delta t without multiplying by 60 s/min60\text{ s/min}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking that the SI definition of power (1 W=1 J/s1\text{ W} = 1\text{ J/s}) requires time to be in seconds to yield energy in joules. A helpful physical checkpoint is noticing that an efficiency of 4000%4000\% violates the conservation of energy, which immediately flags that the denominator was drastically underestimated.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Unit Consistency Check
  • 1 W=1 J/s1\text{ W} = 1\text{ J/s}, so E [J]=P [W]⋅t [s]E\text{ [J]} = P\text{ [W]} \cdot t\text{ [s]}. Time in minutes or hours must always be converted to seconds before multiplying by watts.

  • Write out explicit units during multiplication: (43.2 J/s)×(10.0 min×60 s/min)=25920 J(43.2\text{ J/s}) \times (10.0\text{ min} \times 60\text{ s/min}) = 25920\text{ J}.

Physical Sanity Check on Efficiency
  • In any passive energy conversion system without an external energy source, η≤100%\eta \le 100\%.

  • If your calculated efficiency exceeds 100%100\%, recheck whether your input energy or power has a missing time-conversion factor.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the run time to seconds: Δt=10.0 min×60 s/min=600 s\Delta t = 10.0\text{ min} \times 60\text{ s/min} = 600\text{ s}.

  2. Calculate the true electrical input energy: Eelec=P⋅Δt=43.2 W×600 s=25920 J≈2.59×104 JE_{\text{elec}} = P \cdot \Delta t = 43.2\text{ W} \times 600\text{ s} = 25920\text{ J} \approx 2.59 \times 10^4\text{ J}.

  3. Compute the overall efficiency: η=QabsorbedEelec×100%=17278.6 J25920 J×100%≈66.8%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} \times 100\% = \frac{17278.6\text{ J}}{25920\text{ J}} \times 100\% \approx 66.8\%.

Final answer

(a) Eelec=2.59×104 JE_{\text{elec}} = 2.59 \times 10^4\text{ J}; (b) Qabsorbed=1.73×104 JQ_{\text{absorbed}} = 1.73 \times 10^4\text{ J}; (c) η=66.8%\eta = 66.8\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the unit conversion factor explicitly when substituting time given in minutes or hours into E=PΔtE = P \Delta t.

  • Perform a quick feasibility check on dimensionless quantities like efficiency to catch orders-of-magnitude errors before finalizing your answer.

OverviewACEpath Teacher's Diagnosis

02 The student neglects the heat capacity of the aluminum cup and calculates the absorbed thermal energy considering only the water.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Δt=10.0 min×60 s/min=600 s  ⟹  Eelec=V⋅I⋅Δt=18.0 V×2.40 A×600 s=25920 J\Delta t = 10.0\text{ min} \times 60\text{ s/min} = 600\text{ s} \implies E_{\text{elec}} = V \cdot I \cdot \Delta t = 18.0\text{ V} \times 2.40\text{ A} \times 600\text{ s} = 25920\text{ J}

  2. Step 2

    ΔT=29.85∘C−21.40∘C=8.45∘C  ⟹  Qabsorbed=mwcwΔT=(0.450 kg)(4184 J/(kg⋅K))(8.45 K)=15909.7 J\Delta T = 29.85^\circ\text{C} - 21.40^\circ\text{C} = 8.45^\circ\text{C} \implies Q_{\text{absorbed}} = m_w c_w \Delta T = (0.450\text{ kg})(4184\text{ J/(kg}\cdot\text{K)})(8.45\text{ K}) = 15909.7\text{ J}

    Correct

    Qabsorbed=(mwcw+mAlcAl)ΔT=[(0.450)(4184)+(0.180)(900)]×8.45=2044.8×8.45=17278.56 J≈1.73×104 JQ_{\text{absorbed}} = (m_w c_w + m_{\text{Al}} c_{\text{Al}})\Delta T = [(0.450)(4184) + (0.180)(900)] \times 8.45 = 2044.8 \times 8.45 = 17278.56\text{ J} \approx 1.73 \times 10^4\text{ J}

    You found the correct temperature difference ΔT=8.45 K\Delta T = 8.45\text{ K}, but the defined system includes both the liquid water and the aluminum cup. You need to add the heat absorbed by the cup, mAlcAlΔTm_{\text{Al}} c_{\text{Al}} \Delta T.

  3. Step 3

    η=QabsorbedEelec=15909.7 J25920 J=0.614=61.4%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} = \frac{15909.7\text{ J}}{25920\text{ J}} = 0.614 = 61.4\%

    Correct

    η=QabsorbedEelec=17278.56 J25920 J≈66.8%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} = \frac{17278.56\text{ J}}{25920\text{ J}} \approx 66.8\%

    Your efficiency definition is correct, but your numerical answer is lower than expected because it used the incomplete value of QabsorbedQ_{\text{absorbed}} from step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted minutes to seconds accurately.

You applied the electrical energy formula Eelec=VIΔtE_{\text{elec}} = V I \Delta t correctly.

You calculated the temperature change ΔT\Delta T correctly.

You used the correct ratio of useful thermal energy to total electrical input for efficiency.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Component Heat Capacity

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the calorimeter as an ideal, non-absorbing container rather than summing the heat capacities of all masses inside the defined system boundaries (water plus aluminum cup).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define System Boundaries
  • Every physical component inside the thermal system boundary that experiences the temperature change ΔT\Delta T absorbs heat: Qtotal=∑miciΔTQ_{\text{total}} = \sum m_i c_i \Delta T.

  • Check the problem statement for container masses and specific heat capacities before writing down Q=mcΔTQ = mc\Delta T.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Include the heat capacity of the aluminum cup: CAl=mAlcAl=(0.180 kg)(900 J/(kg⋅K))=162 J/KC_{\text{Al}} = m_{\text{Al}} c_{\text{Al}} = (0.180\text{ kg})(900\text{ J/(kg}\cdot\text{K)}) = 162\text{ J/K}.

  2. Add the heat capacity of the water: Cw=mwcw=(0.450 kg)(4184 J/(kg⋅K))=1882.8 J/KC_w = m_w c_w = (0.450\text{ kg})(4184\text{ J/(kg}\cdot\text{K)}) = 1882.8\text{ J/K}.

  3. Compute total thermal energy: Qabsorbed=(162+1882.8) J/K×8.45 K=17278.56 J≈1.73×104 JQ_{\text{absorbed}} = (162 + 1882.8)\text{ J/K} \times 8.45\text{ K} = 17278.56\text{ J} \approx 1.73 \times 10^4\text{ J}.

  4. Recalculate efficiency: η=17278.56 J25920 J≈0.667≈66.8%\eta = \frac{17278.56\text{ J}}{25920\text{ J}} \approx 0.667 \approx 66.8\%.

Final answer

(a) Eelec=2.59×104 JE_{\text{elec}} = 2.59 \times 10^4\text{ J}; (b) Qabsorbed=1.73×104 JQ_{\text{absorbed}} = 1.73 \times 10^4\text{ J}; (c) η=66.8%\eta = 66.8\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Review calorimetry problems involving non-negligible container heat capacities.

  • Practice identifying all components within thermodynamic boundaries before summing mcΔTmc\Delta T terms.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the definition of efficiency, computing input electrical energy divided by absorbed heat energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Δt=10.0×60=600 s  ⟹  Eelec=(18.0 V)(2.40 A)(600 s)=25920 J\Delta t = 10.0 \times 60 = 600\text{ s} \implies E_{\text{elec}} = (18.0\text{ V})(2.40\text{ A})(600\text{ s}) = 25920\text{ J}

  2. Step 2

    ΔT=29.85−21.40=8.45∘C  ⟹  Qabsorbed=((0.180)(900)+(0.450)(4184))×8.45=(162+1882.8)×8.45=17278.6 J\Delta T = 29.85 - 21.40 = 8.45^\circ\text{C} \implies Q_{\text{absorbed}} = ((0.180)(900) + (0.450)(4184)) \times 8.45 = (162 + 1882.8) \times 8.45 = 17278.6\text{ J}

  3. Step 3

    η=EelecQabsorbed=25920 J17278.6 J=1.50=150%\eta = \frac{E_{\text{elec}}}{Q_{\text{absorbed}}} = \frac{25920\text{ J}}{17278.6\text{ J}} = 1.50 = 150\%

    Correct

    η=QabsorbedEelec=17278.6 J25920 J≈66.8%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} = \frac{17278.6\text{ J}}{25920\text{ J}} \approx 66.8\%

    Efficiency is defined as useful energy output divided by total energy input (EoutEin\frac{E_{\text{out}}}{E_{\text{in}}}). Here, electrical energy is the input and absorbed thermal energy is the output.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted elapsed time from minutes to seconds properly.

You used the correct electric power formula P=VIP = VI to obtain the input energy.

You properly summed the heat capacities of both components of the calorimeter system.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Efficiency Ratio

You set up the efficiency fraction upside down as inputoutput\frac{\text{input}}{\text{output}} rather than useful outputtotal input\frac{\text{useful output}}{\text{total input}}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the roles of input and output energy in an energy conversion chain, along with not catching that an efficiency over 100%100\% violates the conservation of energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Input vs. Output
  • Efficiency is always η=Euseful, outEtotal, in\eta = \frac{E_{\text{useful, out}}}{E_{\text{total, in}}}.

  • Trace the direction of the energy flow: electrical power is supplied into the system, and absorbed heat is what the system successfully gained.

Sanity Check with Conservation of Energy
  • For any passive or driven real-world device without internal sources, η≤100%\eta \le 100\%.

  • Whenever you compute an efficiency exceeding 1.01.0 (or 100%100\%), pause and check if the numerator and denominator were accidentally swapped.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the useful energy output: Eout=Qabsorbed=1.728×104 JE_{\text{out}} = Q_{\text{absorbed}} = 1.728 \times 10^4\text{ J}.

  2. Identify the total energy input: Ein=Eelec=2.592×104 JE_{\text{in}} = E_{\text{elec}} = 2.592 \times 10^4\text{ J}.

  3. Compute efficiency: η=QabsorbedEelec=17278.6 J25920 J≈0.667=66.7%\eta = \frac{Q_{\text{absorbed}}}{E_{\text{elec}}} = \frac{17278.6\text{ J}}{25920\text{ J}} \approx 0.667 = 66.7\% (or 66.8%66.8\% with rounded values).

Final answer

η≈66.8%\eta \approx 66.8\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the energy-conversion chain: trace what energy enters the system from outside versus what useful energy stays inside.

  • Practice labeling EinE_{\text{in}} and EoutE_{\text{out}} explicitly before setting up the fraction.

Lock it in

Similar question

01

An electric immersion heater rated at 120 V120\text{ V} and 2.50 A2.50\text{ A} is placed in an insulated container of water for 5.00 minutes5.00\text{ minutes}. Calculate the total electrical energy delivered by the heater in joules.

Answer

9.00×104 J9.00 \times 10^4\text{ J}. First find power: P=VI=(120 V)(2.50 A)=300 WP = VI = (120\text{ V})(2.50\text{ A}) = 300\text{ W}. Convert time to seconds: t=5.00 min×60 s/min=300 st = 5.00\text{ min} \times 60\text{ s/min} = 300\text{ s}. Then E=Pt=(300 W)(300 s)=90000 JE = Pt = (300\text{ W})(300\text{ s}) = 90000\text{ J}.

02

A 24.0 V24.0\text{ V} DC motor draws 1.50 A1.50\text{ A} of current while lifting a 5.00 kg5.00\text{ kg} load through a vertical height of 18.0 m18.0\text{ m} over a time of 0.500 minutes0.500\text{ minutes}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, determine: (a) the electrical energy input, (b) the useful gravitational potential energy gained, and (c) the overall efficiency of the hoist.

Answer

(a) 1080 J1080\text{ J}; (b) 882 J882\text{ J}; (c) 81.7%81.7\%. Key steps: Pin=(24.0)(1.50)=36.0 WP_{\text{in}} = (24.0)(1.50) = 36.0\text{ W}; t=0.500×60=30.0 st = 0.500 \times 60 = 30.0\text{ s}; Ein=(36.0 W)(30.0 s)=1080 JE_{\text{in}} = (36.0\text{ W})(30.0\text{ s}) = 1080\text{ J}; Euseful=mgh=(5.00)(9.80)(18.0)=882 JE_{\text{useful}} = mgh = (5.00)(9.80)(18.0) = 882\text{ J}; η=8821080×100%≈81.7%\eta = \frac{882}{1080} \times 100\% \approx 81.7\%.

03

In a mechanical equivalent of heat experiment, an electrical stirrer operating at V=15.0 VV = 15.0\text{ V} and I=3.20 AI = 3.20\text{ A} warms 0.250 kg0.250\text{ kg} of liquid (c=2400 J/(kg⋅K)c = 2400\text{ J/(kg}\cdot\text{K)}) housed in a 0.120 kg0.120\text{ kg} copper calorimeter (cCu=386 J/(kg⋅K)c_{\text{Cu}} = 386\text{ J/(kg}\cdot\text{K)}). If the system efficiency is 72.0%72.0\%, calculate the temperature rise ΔT\Delta T after running the stirrer for 12.0 minutes12.0\text{ minutes}.

Answer

ΔT=38.4 K\Delta T = 38.4\text{ K} (or 38.4∘C38.4^\circ\text{C}). Key steps: P=(15.0)(3.20)=48.0 WP = (15.0)(3.20) = 48.0\text{ W}; t=12.0×60=720 st = 12.0 \times 60 = 720\text{ s}; Eelec=(48.0)(720)=34560 JE_{\text{elec}} = (48.0)(720) = 34560\text{ J}. Heat absorbed: Q=η⋅Eelec=0.720×34560=24883.2 JQ = \eta \cdot E_{\text{elec}} = 0.720 \times 34560 = 24883.2\text{ J}. Total heat capacity: Ctot=(0.250)(2400)+(0.120)(386)=600+46.32=646.32 J/KC_{\text{tot}} = (0.250)(2400) + (0.120)(386) = 600 + 46.32 = 646.32\text{ J/K}. Temperature rise: ΔT=QCtot=24883.2646.32≈38.4 K\Delta T = \frac{Q}{C_{\text{tot}}} = \frac{24883.2}{646.32} \approx 38.4\text{ K}.

Loading workspace…