Resources

A heating circuit couples electrical circuit analysis with thermodynamics. An immersion heater is constructed from two identical resistive heating elements, each having resistance R=16.0 ΩR = 16.0\,\Omega, connected in parallel with each other across an ideal 120 V120\text{ V} DC power supply. The immersion heater is submerged in an insulated container holding 0.500 kg0.500\text{ kg} of liquid water at an initial temperature of Ti=20.0∘CT_i = 20.0^\circ\text{C}. Assuming all electrical energy is transferred as heat to the water (with specific heat capacity c=4184 J/(kg⋅∘C)c = 4184\text{ J}/(\text{kg}\cdot^\circ\text{C})) and neglecting heat capacity of the vessel, calculate the time tt in seconds required to heat the water to its boiling point of 100.0∘C100.0^\circ\text{C}.

Answer and steps

Final answer

t=93.0 st = 93.0\text{ s}

Steps

01

Calculate the equivalent resistance and total electrical power

To find the time required to heat the water to its boiling point, we determine the electrical power delivered to the water and equate the total electrical energy supplied to the thermal energy absorbed.

The two heating elements are identical resistors connected in parallel across the voltage source:

  • Each resistor has resistance R=16.0 ΩR = 16.0\,\Omega.
  • Supply voltage V=120 VV = 120\text{ V}.

For two identical resistors connected in parallel, the equivalent resistance ReqR_{\text{eq}} is: Req=R2=16.0 Ω2=8.00 ΩR_{\text{eq}} = \frac{R}{2} = \frac{16.0\,\Omega}{2} = 8.00\,\Omega

The total electrical power PP dissipated by the heater is given by: P=V2Req=(120 V)28.00 Ω=14400 V28.00 Ω=1800 WP = \frac{V^2}{R_{\text{eq}}} = \frac{(120\text{ V})^2}{8.00\,\Omega} = \frac{14400\text{ V}^2}{8.00\,\Omega} = 1800\text{ W}

(Alternative check: each parallel branch experiences the full 120 V120\text{ V}, dissipating P1=V2R=1440016.0=900 WP_1 = \frac{V^2}{R} = \frac{14400}{16.0} = 900\text{ W}. The total power is 2×900 W=1800 W2 \times 900\text{ W} = 1800\text{ W}.)

02

Calculate the thermal energy required to reach boiling point

The heat energy QQ needed to raise the temperature of the water from Ti=20.0∘CT_i = 20.0^\circ\text{C} to Tf=100.0∘CT_f = 100.0^\circ\text{C} is given by the calorimetry formula: Q=m⋅c⋅ΔTQ = m \cdot c \cdot \Delta T

Substitute the given values:

  • Mass of water: m=0.500 kgm = 0.500\text{ kg}
  • Specific heat capacity: c=4184 J/(kg⋅∘C)c = 4184\text{ J}/(\text{kg}\cdot^\circ\text{C})
  • Temperature change: ΔT=100.0∘C−20.0∘C=80.0∘C\Delta T = 100.0^\circ\text{C} - 20.0^\circ\text{C} = 80.0^\circ\text{C}

Q=0.500 kg⋅4184 J/(kg⋅∘C)⋅80.0∘C=167360 JQ = 0.500\text{ kg} \cdot 4184\text{ J}/(\text{kg}\cdot^\circ\text{C}) \cdot 80.0^\circ\text{C} = 167360\text{ J}

03

Solve for the heating time tt

Assuming 100%100\% efficiency, the electrical energy delivered equals the thermal energy absorbed: E=P⋅t=QE = P \cdot t = Q

Solving for time tt: t=QP=167360 J1800 W≈92.98 st = \frac{Q}{P} = \frac{167360\text{ J}}{1800\text{ W}} \approx 92.98\text{ s}

Rounding to three significant figures gives: t=93.0 st = 93.0\text{ s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student treats the two parallel resistors as connected in series, adding their resistances to obtain 32.0 Ω and underestimating the heating power.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Req=16.0 Ω+16.0 Ω=32.0 ΩR_{\text{eq}} = 16.0\,\Omega + 16.0\,\Omega = 32.0\,\Omega

    Correct

    Req=(116.0 Ω+116.0 Ω)−1=8.00 ΩR_{\text{eq}} = \left(\frac{1}{16.0\,\Omega} + \frac{1}{16.0\,\Omega}\right)^{-1} = 8.00\,\Omega

    The problem specifies that the two heating elements are connected in parallel. You added their resistances directly using the series combination formula instead of the reciprocal parallel rule.

  2. Step 2

    P=V2Req=120232.0=450 WP = \frac{V^2}{R_{\text{eq}}} = \frac{120^2}{32.0} = 450\text{ W}

    Correct

    P=V2Req=12028.00=1800 WP = \frac{V^2}{R_{\text{eq}}} = \frac{120^2}{8.00} = 1800\text{ W}

    Your power formula P=V2RP = \frac{V^2}{R} is correct, but substituting the incorrect series resistance of 32.0 Ω32.0\,\Omega led to an underestimated power.

  3. Step 3

    Q=mcΔT=0.500×4184×(100.0−20.0)=167360 JQ = mc\Delta T = 0.500 \times 4184 \times (100.0 - 20.0) = 167360\text{ J}

  4. Step 4

    t=QP=167360450=371.9 st = \frac{Q}{P} = \frac{167360}{450} = 371.9\text{ s}

    Correct

    t=QP=167360 J1800 W≈93.0 st = \frac{Q}{P} = \frac{167360\text{ J}}{1800\text{ W}} \approx 93.0\text{ s}

    Your relationship t=QPt = \frac{Q}{P} is completely sound, but substituting P=450 WP = 450\text{ W} propagated the earlier equivalent resistance error into the final time.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the heat energy needed to bring the water to boiling using Q=mcΔTQ = mc\Delta T.

You correctly related electrical energy and thermal energy using t=QPt = \frac{Q}{P}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Parallel vs. series resistor formula confusion

You used the simple sum formula R1+R2R_1 + R_2 instead of combining parallel resistors via reciprocals.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated parallel branches as a single series loop, overlooking that connecting identical resistors in parallel provides multiple current paths, which halves the total equivalent resistance rather than doubling it.

REASONING PATH
Your ACEpath teacher’s suggested approach
Parallel Resistor Combination
  • For two identical resistors RR in parallel, 1Req=1R+1R  ⟹  Req=R2\frac{1}{R_{\text{eq}}} = \frac{1}{R} + \frac{1}{R} \implies R_{\text{eq}} = \frac{R}{2}.

  • Always verify circuit topology keywords ('in parallel' vs. 'in series') before writing the equivalent resistance formula.

Parallel Branch Power Check
  • In parallel, each resistor receives the full supply voltage VV, so total power is Ptotal=N×V2RP_{\text{total}} = N \times \frac{V^2}{R}.

  • Check your equivalent power by calculating the power of one branch first: each 16 Ω16\,\Omega resistor dissipates 120216=900 W\frac{120^2}{16} = 900\text{ W}, so two branches must deliver 1800 W1800\text{ W}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Req=R2=16.0 Ω2=8.00 ΩR_{\text{eq}} = \frac{R}{2} = \frac{16.0\,\Omega}{2} = 8.00\,\Omega

  2. P=V2Req=(120 V)28.00 Ω=1800 WP = \frac{V^2}{R_{\text{eq}}} = \frac{(120\text{ V})^2}{8.00\,\Omega} = 1800\text{ W}

  3. t=QP=167360 J1800 W=92.98… s≈93.0 st = \frac{Q}{P} = \frac{167360\text{ J}}{1800\text{ W}} = 92.98\dots\text{ s} \approx 93.0\text{ s}

Final answer

t=93.0 st = 93.0\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the difference between series (Req=R1+R2R_{\text{eq}} = R_1 + R_2) and parallel (1Req=1R1+1R2\frac{1}{R_{\text{eq}}} = \frac{1}{R_1} + \frac{1}{R_2}) formulas.

  • Practice using the shortcut Req=RnR_{\text{eq}} = \frac{R}{n} whenever nn identical resistors are connected in parallel.

  • Use individual branch powers as a quick sanity check for parallel circuits across an ideal voltage source.

OverviewACEpath Teacher's Diagnosis

02 The student uses the absolute boiling temperature instead of the temperature change when computing the heat energy, resulting in an overestimated required energy and time.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    1Req=116.0+116.0=216.0  ⟹  Req=8.00 Ω\frac{1}{R_{\text{eq}}} = \frac{1}{16.0} + \frac{1}{16.0} = \frac{2}{16.0} \implies R_{\text{eq}} = 8.00\,\Omega

  2. Step 2

    P=V2Req=12028.00=1800 WP = \frac{V^2}{R_{\text{eq}}} = \frac{120^2}{8.00} = 1800\text{ W}

  3. Step 3

    Q=mcT=0.500×4184×100.0=209200 JQ = mcT = 0.500 \times 4184 \times 100.0 = 209200\text{ J}

    Correct

    Q=mcΔT=0.500 kg×4184 J/(kg⋅∘C)×(100.0∘C−20.0∘C)=167360 JQ = mc\Delta T = 0.500\text{ kg} \times 4184\text{ J}/(\text{kg}\cdot^\circ\text{C}) \times (100.0^\circ\text{C} - 20.0^\circ\text{C}) = 167360\text{ J}

    You used the target final temperature 100.0∘C100.0^\circ\text{C} instead of the temperature difference ΔT=Tf−Ti=100.0∘C−20.0∘C=80.0∘C\Delta T = T_f - T_i = 100.0^\circ\text{C} - 20.0^\circ\text{C} = 80.0^\circ\text{C}.

  4. Step 4

    t=QP=2092001800=116.2 st = \frac{Q}{P} = \frac{209200}{1800} = 116.2\text{ s}

    Correct

    t=QP=167360 J1800 W≈93.0 st = \frac{Q}{P} = \frac{167360\text{ J}}{1800\text{ W}} \approx 93.0\text{ s}

    Your relationship between energy, power, and time was set up correctly, but the numerical answer inherits the error from using an incorrect value of QQ.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the equivalent resistance of two identical resistors in parallel.

You accurately computed the total electrical power using P=V2ReqP = \frac{V^2}{R_{\text{eq}}}.

You recognized that energy equals power multiplied by time.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Calorimetry temperature change omitted

You substituted the final boiling point TfT_f instead of the net temperature increase ΔT=Tf−Ti\Delta T = T_f - T_i.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating absolute temperature with temperature change when applying the heat formula Q=mcΔTQ = mc\Delta T. Specific heat capacity dictates energy required per degree of temperature change, so only the temperature gained from the initial state requires thermal energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Temperature change in calorimetry
  • Q=mcΔT=mc(Tf−Ti)Q = mc\Delta T = mc(T_f - T_i)

  • Always identify both the initial temperature TiT_i and the final temperature TfT_f, then write ΔT=Tf−Ti\Delta T = T_f - T_i explicitly before computing heat energy.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the temperature increase: ΔT=100.0∘C−20.0∘C=80.0∘C\Delta T = 100.0^\circ\text{C} - 20.0^\circ\text{C} = 80.0^\circ\text{C}.

  2. Calculate the thermal energy required: Q=mcΔT=(0.500 kg)(4184 J/(kg⋅∘C))(80.0∘C)=167360 JQ = mc\Delta T = (0.500\text{ kg})(4184\text{ J}/(\text{kg}\cdot^\circ\text{C}))(80.0^\circ\text{C}) = 167360\text{ J}.

  3. Compute the time using power: t=QP=167360 J1800 W≈93.0 st = \frac{Q}{P} = \frac{167360\text{ J}}{1800\text{ W}} \approx 93.0\text{ s}.

Final answer

t=93.0 st = 93.0\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out ΔT=Tf−Ti\Delta T = T_f - T_i explicitly before plugging values into Q=mcΔTQ = mc\Delta T.

  • Double-check whether a problem asks to heat from an ambient or non-zero initial temperature rather than from 0∘C0^\circ\text{C}.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the power of only one resistor instead of the combination, halving the total power and doubling the required time.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P=V2R=120216.0=900 WP = \frac{V^2}{R} = \frac{120^2}{16.0} = 900\text{ W}

    Correct

    Req=16.0 Ω2=8.00 Ω  ⟹  Ptotal=V2Req=12028.00=1800 WR_{\text{eq}} = \frac{16.0\,\Omega}{2} = 8.00\,\Omega \implies P_{\text{total}} = \frac{V^2}{R_{\text{eq}}} = \frac{120^2}{8.00} = 1800\text{ W} (or Ptotal=2×900 W=1800 WP_{\text{total}} = 2 \times 900\text{ W} = 1800\text{ W})

    You found the power dissipated by one resistor alone. The heater contains two identical 16.0 Ω16.0\,\Omega elements connected in parallel across 120 V120\text{ V}, so both elements dissipate power simultaneously.

  2. Step 2

    Q=mcΔT=0.500×4184×80.0=167360 JQ = mc\Delta T = 0.500 \times 4184 \times 80.0 = 167360\text{ J}

  3. Step 3

    t=QP=167360900=186.0 st = \frac{Q}{P} = \frac{167360}{900} = 186.0\text{ s}

    Correct

    t=QPtotal=167360 J1800 W≈93.0 st = \frac{Q}{P_{\text{total}}} = \frac{167360\text{ J}}{1800\text{ W}} \approx 93.0\text{ s}

    Your formula t=QPt = \frac{Q}{P} and arithmetic are sound, but using the single-resistor power of 900 W900\text{ W} resulted in an answer that is twice the true heating time.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the calorimetry relation Q=mcΔTQ = mc\Delta T to find the thermal energy needed to reach boiling.

You correctly connected electrical power, total heat energy, and time through t=QPt = \frac{Q}{P}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Single branch power substituted for total circuit power

You calculated the power of one branch rather than accounting for both parallel heating elements.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the circuit topology when finding total power: in a multi-element circuit, total power is the sum of the power dissipated by each branch (or V2Req\frac{V^2}{R_{\text{eq}}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Parallel Resistor Power
  • For NN identical resistors in parallel across voltage VV, total power is Ptotal=N⋅V2R=V2R/NP_{\text{total}} = N \cdot \frac{V^2}{R} = \frac{V^2}{R/N}.

  • Always count the number of active heating elements and sum their dissipated powers or find ReqR_{\text{eq}} first.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the total power delivered by the two parallel branches: Ptotal=2×V2R=2×900 W=1800 WP_{\text{total}} = 2 \times \frac{V^2}{R} = 2 \times 900\text{ W} = 1800\text{ W}.

  2. Divide the required heat energy Q=167360 JQ = 167360\text{ J} by the total power: t=167360 J1800 W≈92.98 st = \frac{167360\text{ J}}{1800\text{ W}} \approx 92.98\text{ s}.

Final answer

t=93.0 st = 93.0\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before writing down the power formula, sketch or note the arrangement of all heating elements to confirm whether they are in series or parallel.

  • Check that your power represents the entire system (PtotalP_{\text{total}}) before using it in the energy conservation equation E=P⋅tE = P \cdot t.

Lock it in

Similar question

01

A kettle contains two identical 24.0 Ω24.0\,\Omega heating coils connected in parallel to a 120 V120\text{ V} supply. What is the total electrical power delivered to heat the water?

Answer

P=1200 WP = 1200\text{ W}. For two identical resistors in parallel, Req=24.0 Ω2=12.0 ΩR_{\text{eq}} = \frac{24.0\,\Omega}{2} = 12.0\,\Omega. Power is P=V2Req=120212.0=1200 WP = \frac{V^2}{R_{\text{eq}}} = \frac{120^2}{12.0} = 1200\text{ W}.

02

An immersion heater with three identical 30.0 Ω30.0\,\Omega resistors in parallel is used to heat 0.750 kg0.750\text{ kg} of water (c=4184 J/(kg⋅∘C)c = 4184\text{ J}/(\text{kg}\cdot^\circ\text{C})) by 50.0∘C50.0^\circ\text{C}. If the heater is powered by a 120 V120\text{ V} source, how long does this take?

Answer

t=109 st = 109\text{ s}. Total equivalent resistance is Req=30.0 Ω3=10.0 ΩR_{\text{eq}} = \frac{30.0\,\Omega}{3} = 10.0\,\Omega. Total power is P=120210.0=1440 WP = \frac{120^2}{10.0} = 1440\text{ W}. Required heat is Q=0.750×4184×50.0=156900 JQ = 0.750 \times 4184 \times 50.0 = 156900\text{ J}. Heating time is t=QP=156900 J1440 W≈109 st = \frac{Q}{P} = \frac{156900\text{ J}}{1440\text{ W}} \approx 109\text{ s}.

03

A dual-element water heater has two heating elements, R1=20.0 ΩR_1 = 20.0\,\Omega and R2=30.0 ΩR_2 = 30.0\,\Omega. Compare the heating times to deliver 360 kJ360\text{ kJ} of energy at 240 V240\text{ V} when connected in series versus when connected in parallel.

Answer

Series: tseries=312.5 st_{\text{series}} = 312.5\text{ s}; Parallel: tparallel=75.0 st_{\text{parallel}} = 75.0\text{ s}. In series, Req=20+30=50 ΩR_{\text{eq}} = 20 + 30 = 50\,\Omega, P=240250=1152 WP = \frac{240^2}{50} = 1152\text{ W}, t=3600001152=312.5 st = \frac{360000}{1152} = 312.5\text{ s}. In parallel, Req=20×3020+30=12 ΩR_{\text{eq}} = \frac{20 \times 30}{20 + 30} = 12\,\Omega, P=240212=4800 WP = \frac{240^2}{12} = 4800\text{ W}, t=3600004800=75.0 st = \frac{360000}{4800} = 75.0\text{ s}.

Loading workspace…