Resources

A heavy laboratory container of mass M=35.0 kgM = 35.0\text{ kg} is situated on an adjustable inclined ramp. The coefficients of friction between the container and the ramp surface are μs=0.600\mu_s = 0.600 and μk=0.420\mu_k = 0.420. The ramp's inclination angle θ\theta above the horizontal is slowly increased from θ=0∘\theta = 0^\circ. Determine: (a) the critical angle θcrit\theta_{\text{crit}} at which the container transitions from static equilibrium to slipping down the ramp, and (b) the magnitude of the friction force acting on the container immediately before slipping at θ=θcrit\theta = \theta_{\text{crit}}, and immediately after slipping begins at θ=θcrit\theta = \theta_{\text{crit}}. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

(a) θcrit=31.0∘\theta_{\text{crit}} = 31.0^\circ; (b) Immediately before slipping: fs=177 Nf_s = 177\text{ N}; immediately after slipping begins: fk=124 Nf_k = 124\text{ N}.

Steps

Part (a): Determining the Critical Angle θcrit\theta_{\text{crit}}

  1. Identify the forces acting on the container along and perpendicular to the incline:

    • Gravitational force acting downward: W=MgW = Mg. Resolving this into components gives:
      • Parallel to the incline (down the slope): W∥=Mgsin⁡θW_\parallel = Mg \sin\theta
      • Perpendicular to the incline: W⊥=Mgcos⁡θW_\perp = Mg \cos\theta
    • Normal force perpendicular to the surface: N=Mgcos⁡θN = Mg \cos\theta
    • Static friction directed up the slope, opposing the tendency to slide: fsf_s
  2. Condition for impending motion: As the inclination angle θ\theta increases, the component of gravity pulling the container down the ramp, Mgsin⁡θMg \sin\theta, increases. The container remains at rest as long as static friction can balance this force: fs=Mgsin⁡θf_s = Mg \sin\theta Slipping begins at the critical angle θcrit\theta_{\text{crit}} when the required friction reaches the maximum possible static friction force: fs,max⁡=μsN=μsMgcos⁡θcritf_{s,\max} = \mu_s N = \mu_s Mg \cos\theta_{\text{crit}}
  3. Solve for θcrit\theta_{\text{crit}}: Equating the parallel forces at the threshold of motion: Mgsin⁡θcrit=μsMgcos⁡θcritMg \sin\theta_{\text{crit}} = \mu_s Mg \cos\theta_{\text{crit}} Dividing both sides by Mgcos⁡θcritMg \cos\theta_{\text{crit}}: tan⁡θcrit=μs\tan\theta_{\text{crit}} = \mu_s θcrit=arctan⁡(0.600)≈30.96∘≈31.0∘\theta_{\text{crit}} = \arctan(0.600) \approx 30.96^\circ \approx 31.0^\circ

Part (b): Calculating the Friction Forces at θ=θcrit\theta = \theta_{\text{crit}}

  1. Calculate the normal force at θcrit\theta_{\text{crit}}: Using the exact relationship cos⁡(arctan⁡(0.600))=11+0.6002=11.36≈0.8575\cos(\arctan(0.600)) = \frac{1}{\sqrt{1 + 0.600^2}} = \frac{1}{\sqrt{1.36}} \approx 0.8575: N=Mgcos⁡θcrit=(35.0 kg)(9.80 m/s2)(0.8575)≈294.1 NN = Mg \cos\theta_{\text{crit}} = (35.0\text{ kg})(9.80\text{ m/s}^2)(0.8575) \approx 294.1\text{ N}
  2. Friction immediately before slipping: Right before the container slips, it is held by maximum static friction: fs=fs,max⁡=μsN=(0.600)(294.1 N)≈176.5 N≈177 Nf_s = f_{s,\max} = \mu_s N = (0.600)(294.1\text{ N}) \approx 176.5\text{ N} \approx 177\text{ N} (Alternatively, fs=Mgsin⁡θcrit=343 N×sin⁡(30.96∘)≈177 Nf_s = Mg \sin\theta_{\text{crit}} = 343\text{ N} \times \sin(30.96^\circ) \approx 177\text{ N}.)
  3. Friction immediately after slipping begins: Once sliding starts, static friction abruptly drops to kinetic friction: fk=μkN=(0.420)(294.1 N)≈123.5 N≈124 Nf_k = \mu_k N = (0.420)(294.1\text{ N}) \approx 123.5\text{ N} \approx 124\text{ N}

Common Pitfall: A frequent error is assuming kinetic friction depends on the parallel force component (Mgsin⁡θMg\sin\theta). The kinetic friction force depends strictly on the normal force and the kinetic coefficient (μkN\mu_k N), causing an instantaneous drop in resistive force as soon as motion begins because μk<μs\mu_k < \mu_s.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the kinetic friction coefficient instead of the static friction coefficient to determine the onset of slipping, underestimating the critical angle and both friction forces.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    tan⁡(θcrit)=μk=0.420  ⟹  θcrit=arctan⁡(0.420)=22.8∘\tan(\theta_{\text{crit}}) = \mu_k = 0.420 \implies \theta_{\text{crit}} = \arctan(0.420) = 22.8^\circ

    Correct

    tan⁡(θcrit)=μs=0.600  ⟹  θcrit=arctan⁡(0.600)≈31.0∘\tan(\theta_{\text{crit}}) = \mu_s = 0.600 \implies \theta_{\text{crit}} = \arctan(0.600) \approx 31.0^\circ

    The block is stationary right up to the verge of sliding, so the threshold of motion occurs when the downslope component of gravity balances the maximum static friction force, Mgsin⁡θ=μsMgcos⁡θMg \sin\theta = \mu_s Mg \cos\theta, which gives tan⁡θcrit=μs\tan\theta_{\text{crit}} = \mu_s, not μk\mu_k.

  2. Step 2

    fbefore=μs⋅M⋅g⋅cos⁡(22.8∘)=0.600⋅35.0⋅9.80⋅cos⁡(22.8∘)=190 Nf_{\text{before}} = \mu_s \cdot M \cdot g \cdot \cos(22.8^\circ) = 0.600 \cdot 35.0 \cdot 9.80 \cdot \cos(22.8^\circ) = 190\text{ N}

    Correct

    fs=μsMgcos⁡(31.0∘)=(0.600)(35.0)(9.80)cos⁡(30.96∘)≈177 Nf_s = \mu_s Mg \cos(31.0^\circ) = (0.600)(35.0)(9.80)\cos(30.96^\circ) \approx 177\text{ N}

    Your formula for maximum static friction is correct, and your arithmetic is accurate, but the value is affected because you evaluated it using your critical angle of 22.8∘22.8^\circ instead of 31.0∘31.0^\circ.

  3. Step 3

    fafter=μk⋅M⋅g⋅cos⁡(22.8∘)=0.420⋅35.0⋅9.80⋅cos⁡(22.8∘)=133 Nf_{\text{after}} = \mu_k \cdot M \cdot g \cdot \cos(22.8^\circ) = 0.420 \cdot 35.0 \cdot 9.80 \cdot \cos(22.8^\circ) = 133\text{ N}

    Correct

    fk=μkMgcos⁡(31.0∘)=(0.420)(35.0)(9.80)cos⁡(30.96∘)≈124 Nf_k = \mu_k Mg \cos(31.0^\circ) = (0.420)(35.0)(9.80)\cos(30.96^\circ) \approx 124\text{ N}

    Your formula for kinetic friction once motion begins is correct, but this step is also affected by carrying forward θ=22.8∘\theta = 22.8^\circ rather than θ=31.0∘\theta = 31.0^\circ.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the ramp angle condition for slipping takes the form tan⁡θ=μ\tan\theta = \mu.

You correctly identified that the friction force immediately before slipping is maximum static friction μsN\mu_s N.

You correctly applied kinetic friction μkN\mu_k N once sliding begins.

You computed the arithmetic and trigonometric evaluations accurately based on your assumed angle.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing Static and Kinetic Friction Coefficients at Threshold of Motion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the transition to motion with kinetic friction rather than maximum static friction. Because static friction maintains equilibrium until its absolute threshold fs,max⁡=μsNf_{s,\max} = \mu_s N is exceeded, the critical angle of impending slip depends strictly on μs\mu_s.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Motion State at the Threshold
  • At the verge of slipping (impending motion), the object is still in static equilibrium, so fs=fs,max⁡=μsNf_s = f_{s,\max} = \mu_s N. Kinetic friction μkN\mu_k N only acts once relative motion has already started.

  • Check whether the body is still at rest right at the transition point; if it has not yet moved, use μs\mu_s to find the impending slipping condition.

Equate Forces Along the Incline
  • Along an incline at impending slip, ∑F∥=Mgsin⁡θcrit−μsMgcos⁡θcrit=0  ⟹  tan⁡θcrit=μs\sum F_\parallel = Mg\sin\theta_{\text{crit}} - \mu_s Mg\cos\theta_{\text{crit}} = 0 \implies \tan\theta_{\text{crit}} = \mu_s.

  • Always derive the tangent relationship directly from Newton's first law along the incline using fs,max⁡f_{s,\max}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the static equilibrium condition at the verge of motion: Mgsin⁡θcrit=fs,max⁡=μsMgcos⁡θcritMg \sin\theta_{\text{crit}} = f_{s,\max} = \mu_s Mg \cos\theta_{\text{crit}}.

  2. Solve for the critical angle: tan⁡θcrit=μs=0.600  ⟹  θcrit=arctan⁡(0.600)≈30.96∘≈31.0∘\tan\theta_{\text{crit}} = \mu_s = 0.600 \implies \theta_{\text{crit}} = \arctan(0.600) \approx 30.96^\circ \approx 31.0^\circ.

  3. Compute the normal force at θcrit\theta_{\text{crit}}: N=Mgcos⁡(30.96∘)=(35.0)(9.80)(0.8575)≈294.1 NN = Mg \cos(30.96^\circ) = (35.0)(9.80)(0.8575) \approx 294.1\text{ N}.

  4. Calculate friction immediately before slipping: fs=μsN=(0.600)(294.1 N)≈177 Nf_s = \mu_s N = (0.600)(294.1\text{ N}) \approx 177\text{ N}.

  5. Calculate friction immediately after slipping begins: fk=μkN=(0.420)(294.1 N)≈124 Nf_k = \mu_k N = (0.420)(294.1\text{ N}) \approx 124\text{ N}.

Final answer

(a) θcrit=31.0∘\theta_{\text{crit}} = 31.0^\circ; (b) Immediately before slipping: fs=177 Nf_s = 177\text{ N}; immediately after slipping begins: fk=124 Nf_k = 124\text{ N}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the physical distinction between static friction (which holds an object at rest) and kinetic friction (which opposes ongoing sliding).

  • Practice free-body diagrams for impending motion problems, explicitly labeling the friction force as fs,max⁡=μsNf_{s,\max} = \mu_s N before solving for critical parameters.

OverviewACEpath Teacher's Diagnosis

02 The student equates the normal force directly to the full weight M*g instead of resolving it perpendicular to the ramp as M*g*cos(θ), overestimating the normal force and friction forces.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    tan⁡(θcrit)=μs=0.600  ⟹  θcrit=arctan⁡(0.600)=31.0∘\tan(\theta_{\text{crit}}) = \mu_s = 0.600 \implies \theta_{\text{crit}} = \arctan(0.600) = 31.0^\circ

  2. Step 2

    N=M∗g=35.0∗9.80=343 NN = M * g = 35.0 * 9.80 = 343\text{ N}

    Correct

    N=Mgcos⁡θcrit=(35.0 kg)(9.80 m/s2)cos⁡(31.0∘)≈294 NN = Mg\cos\theta_{\text{crit}} = (35.0\text{ kg})(9.80\text{ m/s}^2)\cos(31.0^\circ) \approx 294\text{ N}

    On an incline angled at θ\theta, the surface supports only the perpendicular component of gravity, Mgcos⁡θMg\cos\theta, not the total weight MgMg.

  3. Step 3

    fbefore=μs∗N=0.600∗343=206 N  ⟹  fafter=μk∗N=0.420∗343=144 Nf_{\text{before}} = \mu_s * N = 0.600 * 343 = 206\text{ N} \implies f_{\text{after}} = \mu_k * N = 0.420 * 343 = 144\text{ N}

    Correct

    fs=μsN=0.600(294.1 N)≈177 N  ⟹  fk=μkN=0.420(294.1 N)≈124 Nf_s = \mu_s N = 0.600(294.1\text{ N}) \approx 177\text{ N} \implies f_k = \mu_k N = 0.420(294.1\text{ N}) \approx 124\text{ N}

    Your formulas for fs=μsNf_s = \mu_s N and fk=μkNf_k = \mu_k N were correct, but the numerical answers were affected by the overestimated normal force.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the critical slip angle to the static friction coefficient via tan⁡θcrit=μs\tan\theta_{\text{crit}} = \mu_s.

You used the static friction coefficient before motion and the kinetic friction coefficient after motion began.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal Force on an Incline Error

You set the normal force equal to the full gravitational force MgMg instead of its perpendicular component Mgcos⁡θMg\cos\theta.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating N=MgN = Mg as a universal rule rather than setting up Newton's second law along the axis perpendicular to the inclined contact surface (ΣF⊥=N−Mgcos⁡θ=0\Sigma F_\perp = N - Mg\cos\theta = 0).

REASONING PATH
Your ACEpath teacher’s suggested approach
Resolve Forces Along Tilted Axes
  • For a surface inclined at angle θ\theta with no perpendicular acceleration, the normal force is N=Mgcos⁡θN = Mg\cos\theta.

  • Always draw a free-body diagram with axes parallel and perpendicular to the ramp before computing friction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up equilibrium perpendicular to the ramp: N=Mgcos⁡θcrit=(35.0 kg)(9.80 m/s2)cos⁡(30.96∘)≈294.1 NN = Mg\cos\theta_{\text{crit}} = (35.0\text{ kg})(9.80\text{ m/s}^2)\cos(30.96^\circ) \approx 294.1\text{ N}.

  2. Calculate maximum static friction immediately before slipping: fs=μsN=(0.600)(294.1 N)≈177 Nf_s = \mu_s N = (0.600)(294.1\text{ N}) \approx 177\text{ N}.

  3. Calculate kinetic friction immediately after slipping starts: fk=μkN=(0.420)(294.1 N)≈124 Nf_k = \mu_k N = (0.420)(294.1\text{ N}) \approx 124\text{ N}.

Final answer

(a) θcrit=31.0∘\theta_{\text{crit}} = 31.0^\circ; (b) Before slipping: fs=177 Nf_s = 177\text{ N}; after slipping: fk=124 Nf_k = 124\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice resolving gravity into Mgsin⁡θMg\sin\theta (down the slope) and Mgcos⁡θMg\cos\theta (into the slope) for any inclined plane problem.

  • Verify that normal force reduces to MgMg only when θ=0∘\theta = 0^\circ.

OverviewACEpath Teacher's Diagnosis

03 The student assumes friction remains unchanged immediately after slipping starts, incorrectly setting the post-slip friction force equal to the maximum static friction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    tan⁡(θcrit)=μs=0.600  ⟹  θcrit=arctan⁡(0.600)=31.0∘\tan(\theta_{\text{crit}}) = \mu_s = 0.600 \implies \theta_{\text{crit}} = \arctan(0.600) = 31.0^\circ

  2. Step 2

    N=M∗g∗cos⁡(31.0∘)=35.0∗9.80∗cos⁡(31.0∘)=294 N  ⟹  fbefore=μs∗N=0.600∗294=176 NN = M * g * \cos(31.0^\circ) = 35.0 * 9.80 * \cos(31.0^\circ) = 294\text{ N} \implies f_{\text{before}} = \mu_s * N = 0.600 * 294 = 176\text{ N}

  3. Step 3

    fafter=fbefore=176 Nf_{\text{after}} = f_{\text{before}} = 176\text{ N}

    Correct

    fafter=fk=μkN=0.420×294 N≈124 Nf_{\text{after}} = f_k = \mu_k N = 0.420 \times 294\text{ N} \approx 124\text{ N}

    Once motion begins, the contact switches from static friction to kinetic friction. Because μk<μs\mu_k < \mu_s, the frictional force drops immediately to fk=μkNf_k = \mu_k N.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived and evaluated the critical slipping angle using tan⁡θcrit=μs\tan\theta_{\text{crit}} = \mu_s.

You correctly resolved the normal force perpendicular to the ramp at the critical angle.

You correctly identified that maximum static friction governs the contact immediately before slipping.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinetic vs. Static Friction Transition

You treated friction as continuous across the motion threshold instead of switching to kinetic friction once sliding starts.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the state change between static equilibrium and kinetic motion: static friction acts when surfaces are stationary relative to each other, but kinetic friction (fk=μkNf_k = \mu_k N) takes over the instant relative sliding begins.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Contact State
  • Before relative motion begins, use static friction (fs≤μsNf_s \le \mu_s N). Once relative motion occurs, use kinetic friction (fk=μkNf_k = \mu_k N).

  • Check whether the surfaces are at rest relative to each other or slipping.

Discontinuous Friction Drop
  • Because μk<μs\mu_k < \mu_s for standard material pairs, the friction force experiences an instantaneous downward step when slipping starts.

  • Recalculate friction using μk\mu_k as soon as relative velocity becomes non-zero.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify that relative sliding has commenced, so kinetic friction governs the contact.

  2. Apply the kinetic friction law: fk=μkNf_k = \mu_k N.

  3. Substitute μk=0.420\mu_k = 0.420 and N=294.1 NN = 294.1\text{ N}: fk=0.420×294.1 N≈123.5 N≈124 Nf_k = 0.420 \times 294.1\text{ N} \approx 123.5\text{ N} \approx 124\text{ N}.

Final answer

(a) θcrit=31.0∘\theta_{\text{crit}} = 31.0^\circ; (b) fbefore=177 Nf_{\text{before}} = 177\text{ N} (or 176 N176\text{ N}), fafter=124 Nf_{\text{after}} = 124\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review flashcards comparing static and kinetic friction regimes.

  • Practice identifying whether a body is stationary or sliding before choosing between μs\mu_s and μk\mu_k.

Lock it in

Similar question

01

A 12.0 kg12.0\text{ kg} crate rests on a horizontal floor where μs=0.500\mu_s = 0.500 and μk=0.350\mu_k = 0.350. (a) What minimum horizontal force PP is required to start the crate moving? (b) What friction force acts on the crate immediately after it begins to slide? Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

N=mg=(12.0)(9.80)=117.6 NN = mg = (12.0)(9.80) = 117.6\text{ N}. (a) To initiate motion, P≥fs,max⁡=μsN=(0.500)(117.6 N)=58.8 NP \ge f_{s,\max} = \mu_s N = (0.500)(117.6\text{ N}) = 58.8\text{ N}. (b) Once sliding, fk=μkN=(0.350)(117.6 N)≈41.2 Nf_k = \mu_k N = (0.350)(117.6\text{ N}) \approx 41.2\text{ N}.

02

A block rests on an adjustable incline with μs=0.800\mu_s = 0.800 and μk=0.550\mu_k = 0.550. If the ramp is tilted to θ=25.0∘\theta = 25.0^\circ, does the block slide? What is the magnitude of the friction force acting on a 5.00 kg5.00\text{ kg} block at this angle? Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Critical angle θcrit=arctan⁡(0.800)≈38.7∘\theta_{\text{crit}} = \arctan(0.800) \approx 38.7^\circ. Since θ=25.0∘<θcrit\theta = 25.0^\circ < \theta_{\text{crit}}, the block does not slide. Because it remains in static equilibrium, fs=mgsin⁡θ=(5.00)(9.80)sin⁡(25.0∘)≈20.7 Nf_s = mg\sin\theta = (5.00)(9.80)\sin(25.0^\circ) \approx 20.7\text{ N} (not μsN\mu_s N).

03

A 20.0 kg20.0\text{ kg} trunk is placed on an incline tilted at θ=35.0∘\theta = 35.0^\circ. The coefficients are μs=0.650\mu_s = 0.650 and μk=0.450\mu_k = 0.450. Determine whether the trunk remains at rest or slides down the ramp, and find its acceleration down the ramp if it moves. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Critical angle θcrit=arctan⁡(0.650)≈33.0∘\theta_{\text{crit}} = \arctan(0.650) \approx 33.0^\circ. Since θ=35.0∘>33.0∘\theta = 35.0^\circ > 33.0^\circ, the trunk slips and accelerates. Kinetic friction applies: fk=μkmgcos⁡θ=(0.450)(20.0)(9.80)cos⁡(35.0∘)≈72.25 Nf_k = \mu_k mg\cos\theta = (0.450)(20.0)(9.80)\cos(35.0^\circ) \approx 72.25\text{ N}. Net force: Fnet=mgsin⁡(35.0∘)−fk=(20.0)(9.80)sin⁡(35.0∘)−72.25≈112.42−72.25=40.17 NF_{\text{net}} = mg\sin(35.0^\circ) - f_k = (20.0)(9.80)\sin(35.0^\circ) - 72.25 \approx 112.42 - 72.25 = 40.17\text{ N}. Acceleration: a=Fnetm=g(sin⁡θ−μkcos⁡θ)≈2.01 m/s2a = \frac{F_{\text{net}}}{m} = g(\sin\theta - \mu_k\cos\theta) \approx 2.01\text{ m/s}^2.

Loading workspace…