Resources

A small block of mass m=0.250 kgm = 0.250\text{ kg} is released from rest at the top of a smooth, frictionless track at height hh. The track terminates in a vertical circular loop of radius R=0.600 mR = 0.600\text{ m}. Using the work-energy theorem and centripetal dynamics, determine (a) the minimum release height hmin⁡h_{\min} required for the block to maintain contact with the track at the very top of the loop and (b) the magnitude of the normal force FNF_N exerted by the track on the block at the bottom of the loop if released from h=2.00 mh = 2.00\text{ m}. Assume g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

(a) hmin⁡=1.50 mh_{\min} = 1.50\text{ m}; (b) FN=18.8 NF_N = 18.8\text{ N}

Steps

Part (a): Minimum Release Height hmin⁡h_{\min}

  1. Condition to complete the loop: At the very top of the vertical loop, the block experiences two downward forces: the gravitational force mgmg and the normal force FN,topF_{N,\text{top}} from the track. Together, these provide the required centripetal force: FN,top+mg=mvtop2RF_{N,\text{top}} + mg = \frac{m v_{\text{top}}^2}{R} To stay on the track and maintain contact, the normal force must be non-negative (FN,top≥0F_{N,\text{top}} \ge 0). At the critical threshold where the block just maintains contact, FN,top=0F_{N,\text{top}} = 0: mg=mvtop2R  ⟹  vtop2=gRmg = \frac{m v_{\text{top}}^2}{R} \implies v_{\text{top}}^2 = gR
  2. Applying Conservation of Mechanical Energy: Because the track is frictionless and the normal force acts perpendicular to the motion at all points, mechanical energy is conserved: Einitial=EtopE_{\text{initial}} = E_{\text{top}} Setting the bottom of the loop as the reference level for potential energy (y=0y = 0), the height at the top of the loop is y=2Ry = 2R: mghmin⁡=mg(2R)+12mvtop2mgh_{\min} = mg(2R) + \frac{1}{2}mv_{\text{top}}^2 Substitute vtop2=gRv_{\text{top}}^2 = gR: mghmin⁡=2mgR+12mgR=52mgRmgh_{\min} = 2mgR + \frac{1}{2}mgR = \frac{5}{2}mgR Dividing both sides by mgmg: hmin⁡=52R=2.5⋅0.600 m=1.50 mh_{\min} = \frac{5}{2}R = 2.5 \cdot 0.600\text{ m} = 1.50\text{ m}

Part (b): Normal Force at the Bottom of the Loop

  1. Velocity at the bottom of the loop: Using conservation of energy between the release point at height h=2.00 mh = 2.00\text{ m} and the bottom of the track (y=0y = 0): mgh=12mvbot2  ⟹  vbot2=2ghmgh = \frac{1}{2}mv_{\text{bot}}^2 \implies v_{\text{bot}}^2 = 2gh
  2. Dynamics at the bottom of the loop: At the bottom, the normal force FNF_N points vertically upward toward the center of the circular loop, while gravity mgmg points vertically downward. The net upward force provides the centripetal acceleration: FN−mg=mvbot2RF_N - mg = \frac{m v_{\text{bot}}^2}{R} Substitute vbot2=2ghv_{\text{bot}}^2 = 2gh into the equation: FN=mg+m(2gh)R=mg(1+2hR)F_N = mg + \frac{m(2gh)}{R} = mg\left(1 + \frac{2h}{R}\right)
  3. Calculate the numerical value: Substitute the given values m=0.250 kgm = 0.250\text{ kg}, g=9.80 m/s2g = 9.80\text{ m/s}^2, h=2.00 mh = 2.00\text{ m}, and R=0.600 mR = 0.600\text{ m}: mg=0.250 kg⋅9.80 m/s2=2.45 Nmg = 0.250\text{ kg} \cdot 9.80\text{ m/s}^2 = 2.45\text{ N} 1+2hR=1+2(2.00 m)0.600 m=1+203=2331 + \frac{2h}{R} = 1 + \frac{2(2.00\text{ m})}{0.600\text{ m}} = 1 + \frac{20}{3} = \frac{23}{3} FN=2.45 N⋅233≈18.8 NF_N = 2.45\text{ N} \cdot \frac{23}{3} \approx 18.8\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes the block just needs zero velocity at the top of the loop rather than accounting for the required centripetal acceleration to maintain contact.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    At top of loop, minimum condition to reach the top is v=0\text{At top of loop, minimum condition to reach the top is } v = 0

    Correct

    FN,top+mg=mvtop2R  ⟹  FN,top≥0  ⟹  vtop2≥gRF_{N,\text{top}} + mg = \frac{mv_{\text{top}}^2}{R} \implies F_{N,\text{top}} \ge 0 \implies v_{\text{top}}^2 \ge gR

    You assumed v=0v = 0 at the peak, but an unconstrained block inside a vertical loop must keep moving fast enough that gravity alone provides the centripetal acceleration (vtop=gRv_{\text{top}} = \sqrt{gR}); otherwise, it falls off the track before reaching the apex.

  2. Step 2

    m⋅g⋅hmin⁡=m⋅g⋅(2R)  ⟹  2R=2⋅0.600 m=1.20 mm \cdot g \cdot h_{\min} = m \cdot g \cdot (2R) \implies 2R = 2 \cdot 0.600\text{ m} = 1.20\text{ m}

    Correct

    mghmin⁡=mg(2R)+12mvtop2=52mgR  ⟹  hmin⁡=2.5(0.600 m)=1.50 mmgh_{\min} = mg(2R) + \frac{1}{2}mv_{\text{top}}^2 = \frac{5}{2}mgR \implies h_{\min} = 2.5(0.600\text{ m}) = 1.50\text{ m}

    Because you set vtop=0v_{\text{top}} = 0, you omitted the kinetic energy required at the top of the loop, underestimating the minimum release height.

  3. Step 3

    m⋅g⋅h=12mvbot2  ⟹  vbot2=2gh=2(9.80)(2.00)=39.2 m2/s2m \cdot g \cdot h = \frac{1}{2}m v_{\text{bot}}^2 \implies v_{\text{bot}}^2 = 2gh = 2(9.80)(2.00) = 39.2\text{ m}^2/\text{s}^2

  4. Step 4

    FN−mg=mvbot2R  ⟹  FN=mg+mvbot2R=2.45+16.33=18.8 NF_N - mg = \frac{mv_{\text{bot}}^2}{R} \implies F_N = mg + \frac{mv_{\text{bot}}^2}{R} = 2.45 + 16.33 = 18.8\text{ N}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly formulated Newton's second law in the radial direction at the bottom of the loop.

You accurately calculated the velocity at the bottom using conservation of mechanical energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Zero-velocity threshold in vertical circular motion

You treated reaching the top of the loop as a simple height-climbing problem with v=0v=0 instead of enforcing circular motion dynamics.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing a constrained track (like a bead on a wire, where v=0v=0 at the top is possible) with an unconstrained surface track, where contact requires FN≥0F_N \ge 0 and therefore a minimum speed vtop=gRv_{\text{top}} = \sqrt{gR}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Critical speed at top of a loop
  • For an unattached object on the inside of a vertical circular track of radius RR, normal force must satisfy FN≥0F_N \ge 0. At the threshold of leaving the track, FN=0F_N = 0, so mg=mv2Rmg = \frac{mv^2}{R}.

  • Always set vtop2=gRv_{\text{top}}^2 = gR for the critical minimum speed condition at the top of a loop.

Energy balance including apex kinetic energy
  • Mechanical energy at the top must account for both gravitational potential energy (2mgR2mgR) and minimum kinetic energy (12mvtop2=12mgR\frac{1}{2}m v_{\text{top}}^2 = \frac{1}{2}mgR).

  • Use Etop=2mgR+12mgR=2.5mgRE_{\text{top}} = 2mgR + \frac{1}{2}mgR = 2.5mgR when calculating the minimum release height.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the radial force equation at the top of the loop: FN,top+mg=mvtop2RF_{N,\text{top}} + mg = \frac{mv_{\text{top}}^2}{R}.

  2. Apply the threshold condition for maintaining contact: FN,top=0  ⟹  vtop2=gRF_{N,\text{top}} = 0 \implies v_{\text{top}}^2 = gR.

  3. Apply conservation of mechanical energy from release to the top: mghmin⁡=mg(2R)+12mvtop2mgh_{\min} = mg(2R) + \frac{1}{2}mv_{\text{top}}^2.

  4. Substitute vtop2=gRv_{\text{top}}^2 = gR: mghmin⁡=2mgR+0.5mgR=2.5mgRmgh_{\min} = 2mgR + 0.5mgR = 2.5mgR.

  5. Solve for hmin⁡h_{\min}: hmin⁡=2.5R=2.5(0.600 m)=1.50 mh_{\min} = 2.5R = 2.5(0.600\text{ m}) = 1.50\text{ m}.

Final answer

(a) hmin⁡=1.50 mh_{\min} = 1.50\text{ m}; (b) FN=18.8 NF_N = 18.8\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Notice whether a path is constrained (bead on a wire) or unconstrained (sliding inside a track / swinging on a string) before choosing the threshold speed at the top.

  • Practice drawing free-body diagrams at the critical topmost point of vertical circles to identify which forces provide the centripetal acceleration.

OverviewACEpath Teacher's Diagnosis

02 The student forgets that the top of the loop is at height 2R and mistakenly uses height R in the conservation of energy equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    At top of loop: m⋅g=m⋅vtop2R  ⟹  vtop2=g⋅R\text{At top of loop: } m \cdot g = \frac{m \cdot v_{\text{top}}^2}{R} \implies v_{\text{top}}^2 = g \cdot R

  2. Step 2

    m⋅g⋅hmin⁡=m⋅g⋅R+(12)⋅m⋅vtop2  ⟹  m⋅g⋅hmin⁡=1.5⋅m⋅g⋅R  ⟹  hmin⁡=1.5⋅R=1.5⋅0.600 m=0.900 mm \cdot g \cdot h_{\min} = m \cdot g \cdot R + \left(\frac{1}{2}\right) \cdot m \cdot v_{\text{top}}^2 \implies m \cdot g \cdot h_{\min} = 1.5 \cdot m \cdot g \cdot R \implies h_{\min} = 1.5 \cdot R = 1.5 \cdot 0.600\text{ m} = 0.900\text{ m}

    Correct

    mghmin⁡=mg(2R)+12mvtop2  ⟹  mghmin⁡=2mgR+0.5mgR=2.5mgR  ⟹  hmin⁡=2.5R=1.50 mmgh_{\min} = mg(2R) + \frac{1}{2}mv_{\text{top}}^2 \implies mgh_{\min} = 2mgR + 0.5mgR = 2.5mgR \implies h_{\min} = 2.5R = 1.50\text{ m}

    You set the potential energy at the highest point of the loop to mgRmgR instead of mg(2R)mg(2R). The vertical position at the top of a circle with radius RR measured from the bottom track is its diameter 2R2R.

  3. Step 3

    m⋅g⋅h=(12)⋅m⋅vbot2  ⟹  vbot2=2⋅g⋅h=2⋅9.80⋅2.00=39.2 m2/s2m \cdot g \cdot h = \left(\frac{1}{2}\right) \cdot m \cdot v_{\text{bot}}^2 \implies v_{\text{bot}}^2 = 2 \cdot g \cdot h = 2 \cdot 9.80 \cdot 2.00 = 39.2\text{ m}^2/\text{s}^2

  4. Step 4

    FN−m⋅g=m⋅vbot2R  ⟹  FN=m⋅g+m⋅vbot2R=0.250⋅9.80+0.250⋅39.20.600=2.45+16.33=18.8 NF_N - m \cdot g = \frac{m \cdot v_{\text{bot}}^2}{R} \implies F_N = m \cdot g + \frac{m \cdot v_{\text{bot}}^2}{R} = 0.250 \cdot 9.80 + \frac{0.250 \cdot 39.2}{0.600} = 2.45 + 16.33 = 18.8\text{ N}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived the critical speed condition vtop2=gRv_{\text{top}}^2 = gR for staying on the circular track.

You properly set up conservation of energy and radial dynamics for the bottom of the loop in part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometry misconception in gravitational potential energy

You used the loop radius RR rather than its full diameter 2R2R as the vertical height of the apex.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the radius of circular curvature RR with the vertical displacement from the bottom to the top of the circle (h=2Rh = 2R).

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference level and apex height
  • When the base of a vertical circle of radius RR is at y=0y = 0, the apex is at y=2Ry = 2R.

  • Always draw a quick height coordinate axis alongside the loop and mark y=0y = 0, y=Ry = R (center), and y=2Ry = 2R (top) before writing energy conservation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify that the apex of the loop of radius RR sits at vertical height ytop=2Ry_{\text{top}} = 2R relative to the bottom baseline.

  2. Write the total mechanical energy conservation equation: mghmin⁡=mg(2R)+12mvtop2mgh_{\min} = mg(2R) + \frac{1}{2}m v_{\text{top}}^2.

  3. Substitute vtop2=gRv_{\text{top}}^2 = gR: mghmin⁡=2mgR+12mgR=52mgRmgh_{\min} = 2mgR + \frac{1}{2}mgR = \frac{5}{2}mgR.

  4. Divide by mgmg to isolate hmin⁡=2.5R=2.5(0.600 m)=1.50 mh_{\min} = 2.5R = 2.5(0.600\text{ m}) = 1.50\text{ m}.

Final answer

(a) hmin⁡=1.50 mh_{\min} = 1.50\text{ m}; (b) FN=18.8 NF_N = 18.8\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch vertical circles with explicit labeled elevations (00, RR, 2R2R) to prevent radius-diameter confusion.

  • Practice vertical loop energy problems where release happens from ramps of different geometries.

OverviewACEpath Teacher's Diagnosis

03 The student equates the normal force directly to the centripetal force at the bottom of the loop, omitting gravity from the radial force balance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m×g=m×vtop2R  ⟹  vtop2=g×Rm \times g = \frac{m \times v_{\text{top}}^2}{R} \implies v_{\text{top}}^2 = g \times R

  2. Step 2

    m×g×hmin⁡=m×g×(2R)+(12)×m×vtop2=2.5×m×g×R  ⟹  hmin⁡=2.5×R=2.5×0.600 m=1.50 mm \times g \times h_{\min} = m \times g \times (2R) + \left(\frac{1}{2}\right) \times m \times v_{\text{top}}^2 = 2.5 \times m \times g \times R \implies h_{\min} = 2.5 \times R = 2.5 \times 0.600\text{ m} = 1.50\text{ m}

  3. Step 3

    m×g×h=(12)×m×vbot2  ⟹  vbot2=2×g×h=2×9.80×2.00=39.2 m2/s2m \times g \times h = \left(\frac{1}{2}\right) \times m \times v_{\text{bot}}^2 \implies v_{\text{bot}}^2 = 2 \times g \times h = 2 \times 9.80 \times 2.00 = 39.2\text{ m}^2/\text{s}^2

  4. Step 4

    FN=m×vbot2RF_N = \frac{m \times v_{\text{bot}}^2}{R}

    Correct

    FN−mg=mvbot2R  ⟹  FN=mg+mvbot2RF_N - mg = \frac{m v_{\text{bot}}^2}{R} \implies F_N = mg + \frac{m v_{\text{bot}}^2}{R}

    At the bottom of the loop, both the upward normal force FNF_N and the downward gravitational force mgmg act along the radial line. Newton's second law requires ΣFradial=FN−mg=mvbot2R\Sigma F_{\text{radial}} = F_N - mg = \frac{m v_{\text{bot}}^2}{R}, so FNF_N must balance both gravity and provide the required centripetal acceleration.

  5. Step 5

    FN=0.250×39.20.600=16.3 NF_N = \frac{0.250 \times 39.2}{0.600} = 16.3\text{ N}

    Correct

    FN=mg+mvbot2R=0.250(9.80)+16.33 N≈18.8 NF_N = mg + \frac{m v_{\text{bot}}^2}{R} = 0.250(9.80) + 16.33\text{ N} \approx 18.8\text{ N}

    This numerical calculation follows correctly from your formula in step 4, but it is incorrect because the mg=2.45 Nmg = 2.45\text{ N} term was missing.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the normal force vanishes at the critical release height at the top of the loop.

You applied conservation of mechanical energy accurately for both the top and bottom positions.

You solved part (a) completely with correct algebraic steps and units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of gravity in radial dynamics

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the net centripetal force ΣFr=mv2R\Sigma F_r = \frac{mv^2}{R} with an individual contact force (FNF_N), leading to the omission of gravity mgmg in the radial free-body diagram at the bottom of the loop.

REASONING PATH
Your ACEpath teacher’s suggested approach
Free-Body Diagram for Circular Motion
  • Centripetal force is not an applied force; it is the net force pointing toward the center of curvature: ΣFcenter=mv2R\Sigma F_{\text{center}} = \frac{mv^2}{R}.

  • Always draw all physical forces (normal force, gravity, tension) first, choose the radial direction toward the center as positive, and write ΣFradial=mv2R\Sigma F_{\text{radial}} = \frac{mv^2}{R}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Newton's second law along the radial axis toward the center of the loop: FN−mg=mvbot2RF_N - mg = \frac{m v_{\text{bot}}^2}{R}.

  2. Rearrange to solve for the normal force: FN=mg+mvbot2RF_N = mg + \frac{m v_{\text{bot}}^2}{R}.

  3. Substitute m=0.250 kgm = 0.250\text{ kg}, g=9.80 m/s2g = 9.80\text{ m/s}^2, and mvbot2R=0.250(39.2)0.600≈16.33 N\frac{m v_{\text{bot}}^2}{R} = \frac{0.250(39.2)}{0.600} \approx 16.33\text{ N}: FN=2.45 N+16.33 N=18.78 N≈18.8 NF_N = 2.45\text{ N} + 16.33\text{ N} = 18.78\text{ N} \approx 18.8\text{ N}.

Final answer

(a) hmin⁡=1.50 mh_{\min} = 1.50\text{ m}; (b) FN=18.8 NF_N = 18.8\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice setting up radial force balance equations at various points of a vertical circle (bottom, top, and horizontal sides).

  • Remember that FNF_N at the bottom of a dip or loop is always greater than the weight because the track must both support gravity and accelerate the object upward.

Lock it in

Similar question

01

A small toy car of mass m=0.100 kgm = 0.100\text{ kg} moves along the inside of a vertical circular loop of radius R=0.400 mR = 0.400\text{ m}. Calculate the minimum speed the car must have at the top of the loop to maintain contact. (Take g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer

vmin⁡=gR=(9.80)(0.400)=3.92≈1.98 m/sv_{\min} = \sqrt{gR} = \sqrt{(9.80)(0.400)} = \sqrt{3.92} \approx 1.98\text{ m/s}.

02

A small block slides down a frictionless ramp and loops a vertical circle of radius R=0.500 mR = 0.500\text{ m}. From what minimum height hmin⁡h_{\min} above the bottom of the loop must it be released from rest to successfully complete the loop?

Answer

At the top, vtop2=gRv_{\text{top}}^2 = gR. By energy conservation, mghmin⁡=mg(2R)+12m(gR)=2.5mgRmgh_{\min} = mg(2R) + \frac{1}{2}m(gR) = 2.5mgR. Therefore, hmin⁡=2.5R=2.5(0.500 m)=1.25 mh_{\min} = 2.5R = 2.5(0.500\text{ m}) = 1.25\text{ m}.

03

A block of mass m=0.200 kgm = 0.200\text{ kg} is released from rest at height h=3.00Rh = 3.00R on a frictionless track that leads into a vertical loop of radius R=0.500 mR = 0.500\text{ m}. Determine the magnitude of the normal force exerted by the track on the block at the top of the loop. (g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer

Energy conservation gives 12mvtop2=mg(h−2R)=mgR  ⟹  vtop2=2gR\frac{1}{2}mv_{\text{top}}^2 = mg(h - 2R) = mgR \implies v_{\text{top}}^2 = 2gR. At the top, FN+mg=mvtop2R=2mg  ⟹  FN=mg=(0.200 kg)(9.80 m/s2)=1.96 NF_N + mg = \frac{mv_{\text{top}}^2}{R} = 2mg \implies F_N = mg = (0.200\text{ kg})(9.80\text{ m/s}^2) = 1.96\text{ N}.

Loading workspace…