Resources

A series-wound DC motor has an internal armature resistance of R=2.40 ΩR = 2.40\ \Omega and is connected across an external power supply of Esource=120 V\mathcal{E}_{\text{source}} = 120\text{ V}. When running at its steady-state operating speed, the spinning armature generates a counter-electromotive force (back-EMF) of Eback=108 V\mathcal{E}_{\text{back}} = 108\text{ V} due to Faraday's law of induction. Coupling Ohm's law with the motor torque principle (where magnetic torque is proportional to operating current, τ=kI\tau = k I with k=0.350 N⋅m/Ak = 0.350\text{ N}\cdot\text{m/A}), calculate: (a) the inrush current IstartI_{\text{start}} and starting torque τstart\tau_{\text{start}} at the instant of motor startup before motion begins, and (b) the operating current IrunI_{\text{run}} and steady running torque τrun\tau_{\text{run}}.

Answer and steps

Final answer

(a) Istart=50.0 AI_{\text{start}} = 50.0\text{ A} and τstart=17.5 N⋅m\tau_{\text{start}} = 17.5\text{ N}\cdot\text{m}; (b) Irun=5.00 AI_{\text{run}} = 5.00\text{ A} and τrun=1.75 N⋅m\tau_{\text{run}} = 1.75\text{ N}\cdot\text{m}.

Steps

Operating Principle of a DC Motor

A DC motor consists of a current-carrying armature coil inside a magnetic field. When connected to a voltage source Esource\mathcal{E}_{\text{source}}, the current II passing through the coil experiences a magnetic force that produces a mechanical torque: τ=kI\tau = k I As the armature rotates, the magnetic flux through the turning coils continuously changes. According to Faraday's law of induction and Lenz's law, this rotation induces a counter-electromotive force, or back-EMF (Eback\mathcal{E}_{\text{back}}), that opposes the source voltage.

Applying Kirchhoff's loop rule to the motor circuit gives the net voltage driving the current: Esource−Eback=IR  ⟹  I=Esource−EbackR\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}} = I R \implies I = \frac{\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}}{R}


(a) Startup Conditions (Inrush Current and Starting Torque)

  1. Calculate the starting current (IstartI_{\text{start}}): At the instant the motor is energized, the armature has not yet begun to rotate (ω=0\omega = 0). Therefore, no back-EMF is generated: Eback=0 V\mathcal{E}_{\text{back}} = 0\text{ V}

    The inrush current is limited only by the internal armature resistance: Istart=Esource−0 VR=120 V2.40 Ω=50.0 AI_{\text{start}} = \frac{\mathcal{E}_{\text{source}} - 0\text{ V}}{R} = \frac{120\text{ V}}{2.40\ \Omega} = 50.0\text{ A}

  2. Calculate the starting torque (τstart\tau_{\text{start}}): Using the torque relationship τ=kI\tau = k I: τstart=(0.350 N⋅m/A)⋅(50.0 A)=17.5 N⋅m\tau_{\text{start}} = (0.350\text{ N}\cdot\text{m/A}) \cdot (50.0\text{ A}) = 17.5\text{ N}\cdot\text{m}

Common Pitfall: Forgetting that back-EMF depends on motion. At startup, Eback=0\mathcal{E}_{\text{back}} = 0, leading to a very large "inrush" current that can damage motors if not properly managed or limited.


(b) Steady-State Running Conditions

  1. Calculate the operating current (IrunI_{\text{run}}): At full operating speed, the spinning armature generates a back-EMF of Eback=108 V\mathcal{E}_{\text{back}} = 108\text{ V}.

    The effective voltage across the armature resistance is reduced to: Enet=Esource−Eback=120 V−108 V=12 V\mathcal{E}_{\text{net}} = \mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}} = 120\text{ V} - 108\text{ V} = 12\text{ V}

    Therefore, the steady-state running current is: Irun=12 V2.40 Ω=5.00 AI_{\text{run}} = \frac{12\text{ V}}{2.40\ \Omega} = 5.00\text{ A}

  2. Calculate the running torque (τrun\tau_{\text{run}}): τrun=(0.350 N⋅m/A)⋅(5.00 A)=1.75 N⋅m\tau_{\text{run}} = (0.350\text{ N}\cdot\text{m/A}) \cdot (5.00\text{ A}) = 1.75\text{ N}\cdot\text{m}

As the motor accelerates, back-EMF increases, naturally reducing the armature current and torque until the driving torque balances the mechanical load.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student mistakenly includes the steady-state back-EMF at startup, resulting in an underestimated starting current and starting torque.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Istart=(120−108)2.40  ⟹  Istart=122.40=5.00 AI_{\text{start}} = \frac{(120 - 108)}{2.40} \implies I_{\text{start}} = \frac{12}{2.40} = 5.00\text{ A}

    Correct

    Istart=Esource−0R=120 V2.40 Ω=50.0 AI_{\text{start}} = \frac{\mathcal{E}_{\text{source}} - 0}{R} = \frac{120\text{ V}}{2.40\ \Omega} = 50.0\text{ A}

    You subtracted the operating back-EMF (108 V108\text{ V}) when finding the starting current. At the exact instant of startup, the armature is stationary (ω=0\omega = 0), so no back-EMF has developed yet (Eback=0 V\mathcal{E}_{\text{back}} = 0\text{ V}).

  2. Step 2

    τstart=0.350∗5.00=1.75 N⋅m\tau_{\text{start}} = 0.350 * 5.00 = 1.75\text{ N}\cdot\text{m}

    Correct

    τstart=kIstart=(0.350 N⋅m/A)(50.0 A)=17.5 N⋅m\tau_{\text{start}} = k I_{\text{start}} = (0.350\text{ N}\cdot\text{m/A})(50.0\text{ A}) = 17.5\text{ N}\cdot\text{m}

    You applied the torque formula τ=kI\tau = k I correctly, but your numerical answer was carried over from your starting current in Step 1.

  3. Step 3

    Irun=(120−108)2.40=5.00 AI_{\text{run}} = \frac{(120 - 108)}{2.40} = 5.00\text{ A}

  4. Step 4

    τrun=0.350∗5.00=1.75 N⋅m\tau_{\text{run}} = 0.350 * 5.00 = 1.75\text{ N}\cdot\text{m}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Ohm's law and Kirchhoff's loop rule to find the running current.

You accurately applied the proportional relationship τ=kI\tau = k I to calculate magnetic torque.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Startup back-EMF misconception

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated back-EMF as a fixed constant of the motor circuit rather than a motion-dependent induced voltage that is strictly zero before rotation begins.

REASONING PATH
Your ACEpath teacher’s suggested approach
Evaluate Speed Before Calculating Back-EMF
  • Back-EMF is produced by Faraday induction (Eback∝ω\mathcal{E}_{\text{back}} \propto \omega) and is strictly zero when the armature is at rest.

  • Always set Eback=0 V\mathcal{E}_{\text{back}} = 0\text{ V} at the instant the switch closes (t=0t = 0), so Istart=EsourceRI_{\text{start}} = \frac{\mathcal{E}_{\text{source}}}{R}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. At startup, the armature is not rotating, so Eback=0 V\mathcal{E}_{\text{back}} = 0\text{ V}.

  2. Istart=Esource−0 VR=120 V2.40 Ω=50.0 AI_{\text{start}} = \frac{\mathcal{E}_{\text{source}} - 0\text{ V}}{R} = \frac{120\text{ V}}{2.40\ \Omega} = 50.0\text{ A}.

  3. Compute starting torque: τstart=kIstart=(0.350 N⋅m/A)(50.0 A)=17.5 N⋅m\tau_{\text{start}} = k I_{\text{start}} = (0.350\text{ N}\cdot\text{m/A})(50.0\text{ A}) = 17.5\text{ N}\cdot\text{m}.

Final answer

(a) Istart=50.0 AI_{\text{start}} = 50.0\text{ A} and τstart=17.5 N⋅m\tau_{\text{start}} = 17.5\text{ N}\cdot\text{m}; (b) Irun=5.00 AI_{\text{run}} = 5.00\text{ A} and τrun=1.75 N⋅m\tau_{\text{run}} = 1.75\text{ N}\cdot\text{m}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how Faraday's law links induced back-EMF directly to rotational speed ω\omega.

  • Practice distinguishing between locked-rotor/startup conditions and steady-state rated conditions in motor circuits.

OverviewACEpath Teacher's Diagnosis

02 The student adds the back-EMF to the supply voltage instead of subtracting it when calculating the operating current, leading to an artificially high running current and torque.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    At startup, \text{At startup, } E_{back\text{back}} = 0   ⟹  \implies I_{start\text{start}} = 1202.40\frac{120}{2.40} = 50.0 A\text{ A}   ⟹  \implies τ\tau{start\text{start}} = 0.350 ×\times 50.0 = 17.5\text{ N}$$\cdot$$\text{m}

  2. Step 2

    I_{run\text{run}} = 120+1082.40\frac{120 + 108}{2.40} = 2282.40\frac{228}{2.40} = 95.0 A\text{ A}_

    Correct

    I_{run\text{run}} = Esource−EbackR\frac{\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}}{R} = 120 V−108 V2.40 Ω\frac{120\text{ V} - 108\text{ V}}{2.40\ \Omega} = 12 V2.40 Ω\frac{12\text{ V}}{2.40\ \Omega} = 5.00 A\text{ A}_

    You added the back-EMF to the source voltage instead of subtracting it. By Lenz's law, the counter-electromotive force opposes the external voltage driving the current, so the net voltage across the armature is Esource−Eback\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}.

  3. Step 3

    τ\tau{run\text{run}} = 0.350 ×\times 95.0 = 33.25\text{ N}$$\cdot$$\text{m}

    Correct

    τ\tau{run\text{run}} = k I{run\text{run}} = 0.350\text{ N}$$\cdot$$\text{m/A} ×\times 5.00 A\text{ A} = 1.75\text{ N}$$\cdot$$\text{m}

    You correctly applied the torque formula τ=kI\tau = k I, but your calculated value was affected by the incorrect running current from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the back-EMF is zero when the armature is not yet moving at startup.

You accurately calculated the startup current using Ohm's law.

You correctly applied the proportional torque relationship τ=kI\tau = k I.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Back-EMF Sign Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misinterpreting the directional role of counter-electromotive force in Kirchhoff's loop rule by treating back-EMF as an aiding voltage source rather than an opposing potential difference.

REASONING PATH
Your ACEpath teacher’s suggested approach
Direction of Back-EMF
  • By Lenz's law and Faraday's law of induction, the induced counter-EMF in a rotating motor always opposes the applied line voltage: Vnet=Esource−EbackV_{\text{net}} = \mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}.

  • Always subtract the back-EMF from the source voltage when writing Kirchhoff's voltage loop for a motor.

Physical Sanity Check for Motors
  • Because back-EMF increases with rotation speed, the net voltage and current must decrease from startup to full running speed: Irun<IstartI_{\text{run}} < I_{\text{start}}.

  • Check that your running current is significantly smaller than the starting (inrush) current.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Subtract the back-EMF from the supply voltage to find the net driving voltage: Vnet=120 V−108 V=12 VV_{\text{net}} = 120\text{ V} - 108\text{ V} = 12\text{ V}.

  2. Calculate the steady running current: Irun=12 V2.40 Ω=5.00 AI_{\text{run}} = \frac{12\text{ V}}{2.40\ \Omega} = 5.00\text{ A}.

  3. Calculate the running torque: τrun=0.350 N⋅m/A×5.00 A=1.75 N⋅m\tau_{\text{run}} = 0.350\text{ N}\cdot\text{m/A} \times 5.00\text{ A} = 1.75\text{ N}\cdot\text{m}.

Final answer

(a) Istart=50.0 AI_{\text{start}} = 50.0\text{ A} and τstart=17.5 N⋅m\tau_{\text{start}} = 17.5\text{ N}\cdot\text{m}; (b) Irun=5.00 AI_{\text{run}} = 5.00\text{ A} and τrun=1.75 N⋅m\tau_{\text{run}} = 1.75\text{ N}\cdot\text{m}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review Kirchhoff's loop law applied to motors to cement why back-EMF acts as an opposing battery.

  • Perform a quick physical plausibility check: an electric motor draws its peak current at startup, not during steady-state rotation.

  • Practice solving similar motor circuits with varying loads and mechanical friction.

OverviewACEpath Teacher's Diagnosis

03 The student ignores the counter-electromotive force when calculating steady-state operation, treating the motor as a simple static resistor and obtaining identical startup and running values.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Istart=1202.40=50.0 AI_{\text{start}} = \frac{120}{2.40} = 50.0\text{ A}

  2. Step 2

    τstart=0.350∗50.0=17.5 N⋅m\tau_{\text{start}} = 0.350 * 50.0 = 17.5\text{ N}\cdot\text{m}

  3. Step 3

    Irun=1202.40=50.0 AI_{\text{run}} = \frac{120}{2.40} = 50.0\text{ A}

    Correct

    Irun=Esource−EbackR=120 V−108 V2.40 Ω=12 V2.40 Ω=5.00 AI_{\text{run}} = \frac{\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}}{R} = \frac{120\text{ V} - 108\text{ V}}{2.40\ \Omega} = \frac{12\text{ V}}{2.40\ \Omega} = 5.00\text{ A}

    You did not account for the 108 V108\text{ V} counter-electromotive force generated when the armature spins. The net voltage driving the current in steady state is Esource−Eback\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}.

  4. Step 4

    τrun=0.350∗50.0=17.5 N⋅m\tau_{\text{run}} = 0.350 * 50.0 = 17.5\text{ N}\cdot\text{m}

    Correct

    τrun=kIrun=(0.350 N⋅m/A)(5.00 A)=1.75 N⋅m\tau_{\text{run}} = k I_{\text{run}} = (0.350\text{ N}\cdot\text{m/A})(5.00\text{ A}) = 1.75\text{ N}\cdot\text{m}

    Your torque formula setup was correct, but the calculated value carried over the incorrect operating current from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the motor generates zero back-EMF before rotation begins.

You accurately calculated the startup inrush current using Ohm's law.

You applied the linear torque-current relationship τ=kI\tau = k I accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Back-EMF in Steady-State Operation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the rotating DC motor as an ordinary fixed ohmic resistor, overlooking that rotation induces an opposing voltage (back-EMF) via Faraday's and Lenz's laws, which reduces the net voltage across the armature windings.

REASONING PATH
Your ACEpath teacher’s suggested approach
Apply Kirchhoff's loop rule with back-EMF
  • I=Esource−EbackRI = \frac{\mathcal{E}_{\text{source}} - \mathcal{E}_{\text{back}}}{R}

  • Always subtract the induced counter-EMF from the supply voltage to find the net driving voltage across the internal winding resistance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Subtract the back-EMF from the source voltage to find the net voltage across the armature: Vnet=120 V−108 V=12 VV_{\text{net}} = 120\text{ V} - 108\text{ V} = 12\text{ V}.

  2. Calculate the steady-state operating current: Irun=12 V2.40 Ω=5.00 AI_{\text{run}} = \frac{12\text{ V}}{2.40\ \Omega} = 5.00\text{ A}.

  3. Substitute the steady-state current into the torque equation: τrun=(0.350 N⋅m/A)(5.00 A)=1.75 N⋅m\tau_{\text{run}} = (0.350\text{ N}\cdot\text{m/A})(5.00\text{ A}) = 1.75\text{ N}\cdot\text{m}.

Final answer

(a) Istart=50.0 AI_{\text{start}} = 50.0\text{ A} and τstart=17.5 N⋅m\tau_{\text{start}} = 17.5\text{ N}\cdot\text{m}; (b) Irun=5.00 AI_{\text{run}} = 5.00\text{ A} and τrun=1.75 N⋅m\tau_{\text{run}} = 1.75\text{ N}\cdot\text{m}

NEXT STEPS
Final Takeaways from Your Teacher
  • When analyzing electric motors, draw an equivalent circuit that includes both the armature resistance RR and a variable opposing source Eback\mathcal{E}_{\text{back}}.

  • Verify that operating current and torque are substantially lower than startup values, as spinning armatures naturally throttle current via back-EMF.

Lock it in

Similar question

01

A 240 V240\text{ V} DC motor has an internal resistance of 1.50 Ω1.50\ \Omega and develops a back-EMF of 210 V210\text{ V} at full speed. Calculate the startup inrush current IstartI_{\text{start}} and the steady operating current IrunI_{\text{run}}.

Answer

Istart=160 AI_{\text{start}} = 160\text{ A} and Irun=20.0 AI_{\text{run}} = 20.0\text{ A}. At startup, Eback=0\mathcal{E}_{\text{back}} = 0, giving Istart=240 V1.50 Ω=160 AI_{\text{start}} = \frac{240\text{ V}}{1.50\ \Omega} = 160\text{ A}. At full speed, Irun=240 V−210 V1.50 Ω=30 V1.50 Ω=20.0 AI_{\text{run}} = \frac{240\text{ V} - 210\text{ V}}{1.50\ \Omega} = \frac{30\text{ V}}{1.50\ \Omega} = 20.0\text{ A}.

02

A motor with armature resistance R=0.80 ΩR = 0.80\ \Omega and torque constant k=0.25 N⋅m/Ak = 0.25\text{ N}\cdot\text{m/A} is connected to a 48 V48\text{ V} source. Find the ratio of starting torque to running torque if its back-EMF at operating speed is 40 V40\text{ V}.

Answer

Ratio is 6:16 : 1 (or 6.06.0). At startup, Istart=48 V0.80 Ω=60 AI_{\text{start}} = \frac{48\text{ V}}{0.80\ \Omega} = 60\text{ A}. At speed, Irun=48 V−40 V0.80 Ω=10 AI_{\text{run}} = \frac{48\text{ V} - 40\text{ V}}{0.80\ \Omega} = 10\text{ A}. Because τ∝I\tau \propto I, τstartτrun=IstartIrun=60 A10 A=6\frac{\tau_{\text{start}}}{\tau_{\text{run}}} = \frac{I_{\text{start}}}{I_{\text{run}}} = \frac{60\text{ A}}{10\text{ A}} = 6.

03

To prevent circuit breaker tripping, a DC motor (R=0.50 ΩR = 0.50\ \Omega, E=100 V\mathcal{E} = 100\text{ V}) uses an external starting resistor RextR_{\text{ext}} in series that cuts inrush current to 25 A25\text{ A}. Find the required resistance RextR_{\text{ext}}, and calculate the motor's operating current once up to speed with RextR_{\text{ext}} switched out and Eback=92 V\mathcal{E}_{\text{back}} = 92\text{ V}.

Answer

Rext=3.5 ΩR_{\text{ext}} = 3.5\ \Omega and Irun=16 AI_{\text{run}} = 16\text{ A}. At startup with Eback=0\mathcal{E}_{\text{back}} = 0, total resistance Rtot=100 V25 A=4.0 ΩR_{\text{tot}} = \frac{100\text{ V}}{25\text{ A}} = 4.0\ \Omega, so Rext=4.0−0.50=3.5 ΩR_{\text{ext}} = 4.0 - 0.50 = 3.5\ \Omega. In steady state without RextR_{\text{ext}}, Irun=100 V−92 V0.50 Ω=8 V0.50 Ω=16 AI_{\text{run}} = \frac{100\text{ V} - 92\text{ V}}{0.50\ \Omega} = \frac{8\text{ V}}{0.50\ \Omega} = 16\text{ A}.

Loading workspace…