Resources
A textbook of mass is held pressed flat against a vertical wall by a student applying a direct horizontal pushing force . The static and kinetic coefficients of friction between the textbook and the wall are and , respectively. Take . (a) Identify the horizontal and vertical forces acting on the book, clarifying which force provides the normal force and which opposes gravity. (b) If the student pushes with a force of , determine the actual magnitude and direction of the friction force acting on the book. (c) Determine the minimum pushing force required to prevent the book from slipping down the wall.
Answer and steps
Final answer
(a) Horizontal: Applied pushing force (inward) and normal force (outward from wall, so ); Vertical: Gravitational force (downward) and static/kinetic friction (upward along the wall); (b) upward (since , the book remains stationary); (c) .
Steps
(a) Force Identification and Free-Body Analysis
When the book is held against a vertical wall, four forces act on it along two perpendicular axes:
-
Horizontal Forces:
- The student exerts a horizontal pushing force perpendicular to the wall (inward).
- The wall exerts a perpendicular contact force, the normal force , directed horizontally away from the wall (outward).
- Because the book has no horizontal acceleration, Newton's first law gives:
- Thus, the student's push directly provides the normal force against the wall.
-
Vertical Forces:
- The Earth exerts a downward gravitational force:
- The microscopic interactions between the book and the wall's surface exert a vertical friction force directed parallel to the wall and upward, opposing the tendency of the book to slide downward.
(b) Determining the Actual Friction Force for
- Calculate the downward weight:
- Determine the maximum possible static friction: Since , the maximum static friction the wall can provide before slipping begins is:
-
Compare required friction to maximum static friction:
- Static friction is an adaptive, self-adjusting force: it only provides as much force as necessary to maintain equilibrium, up to .
- Because the required force to hold the book stationary () is strictly less than the threshold (), the book does not slip.
- Therefore, the actual friction force is:
Common Pitfall: Do not automatically calculate friction as . The formula gives the maximum limit of static friction, not necessarily the actual value when the object is stationary.
(c) Minimum Pushing Force to Prevent Slipping
- Condition for slipping: The book will begin to slide down if the downward weight exceeds the maximum static friction:
- Set up the threshold condition: To just keep the book stationary, the maximum static friction must balance the gravitational force:
- Solve for : Since :
Typical errors
01 The student confuses the actual static friction force required for equilibrium with the maximum possible static friction force, calculating f = μ_s N directly in part (b).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Horizontal forces: pushing force and normal force from the wall, where . Vertical forces: downward gravity and upward friction from the wall opposing gravity.
- Step 2Correct
;
You calculated the maximum possible static friction () rather than the actual friction. Because the book is at rest and , static friction self-adjusts to match the downward gravitational force, .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified all four forces and their balancing relationships in part (a).
You accurately related the applied pushing force to the normal force perpendicular to the wall.
You correctly applied the impending-slip condition in part (c) to find the minimum pushing force.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual misunderstanding of static friction as a fixed formula rather than an adaptive constraint force.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated static friction as having a fixed value given by . In reality, static friction is an inequality () that only provides the exact force needed for equilibrium, reaching only when slipping is impending.
REASONING PATH
Your ACEpath teacher’s suggested approach- Static Friction Nature
For an object at rest, static friction satisfies . Its actual magnitude is determined by Newton's first law (), not by .
Calculate the required balancing force first from equilibrium, then compare it to to confirm the object does not slip.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the downward gravitational force: .
Compute the maximum static friction threshold: .
Check equilibrium: since , the book does not slip, so static friction matches weight: upward.
upward
02 The student misuses the kinetic friction coefficient instead of the static friction coefficient when analyzing the threshold of slipping and actual friction for a stationary object.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Horizontal forces: applied push and normal force from the wall. Vertical forces: gravity downward and friction upward opposing gravity.
- Step 2Correct
. Since , the book remains at rest and upward.
Although your conclusion that the book remains stationary and your final value are numerically correct, you evaluated the threshold of static friction using instead of . The maximum static friction is .
- Step 3Correct
To prevent a stationary book from starting to slide down, the impending motion threshold is governed by maximum static friction (), not kinetic friction. Dividing by gives .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the vertical and horizontal force balances on the textbook.
You correctly recognized that when the book does not slip, the actual static friction matches the downward weight rather than jumping automatically to maximum friction.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted instead of when checking impending motion thresholds.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated static friction (), which resists impending motion between surfaces at rest, with kinetic friction (), which acts only after relative sliding is already occurring.
REASONING PATH
Your ACEpath teacher’s suggested approach- Select the Right Coefficient
Use whenever an object is at rest or on the verge of slipping (); use only when surfaces are actively sliding past each other.
Check the state of motion before writing the friction formula. If and you are preventing sliding, apply .
CORRECTED PATH
ACEpath Teacher's DemonstrationAt the verge of slipping, static friction reaches its maximum possible value: .
Equate the maximum static friction to the downward weight: .
Solve for : .
03 The student assumes the normal force is always equal to the object's weight (N = mg), incorrectly applying horizontal friction concepts to a vertical wall scenario.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Horizontal forces: applied push . Vertical forces: gravity downward and normal force upward supporting the book.
CorrectHorizontal forces: applied push (inward) and normal force (outward from wall, so ). Vertical forces: gravity (downward) and static friction (upward).
A normal force is always perpendicular to the contact surface. Because the wall is vertical, the normal force must be horizontal (pointing away from the wall), balancing your horizontal push. The force holding the book up against gravity parallel to the wall is static friction.
- Step 2Correct
. Since , the book does not slide, so .
You set and assumed friction always equals . With a horizontal push of , the normal force is , giving a maximum available static friction of . Because this threshold exceeds the book's weight (), static friction only exerts what is needed for vertical equilibrium: .
- Step 3Correct
To prevent slipping, maximum static friction must balance weight: . Since , solving for requires dividing by rather than multiplying by it.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the magnitude of the textbook's gravitational force as .
You recognized that an upward force must counteract gravity to keep the textbook in vertical equilibrium.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou carried over the horizontal-floor habit where normal force points upward and equals . On a vertical surface, the normal force is perpendicular to the wall (horizontal), while friction acts parallel to the wall (vertical) to oppose sliding.
REASONING PATH
Your ACEpath teacher’s suggested approach- Define Normal Force Direction
Normal force is always perpendicular (orthogonal) to the contact plane.
Check the wall's orientation first: a vertical wall produces a horizontal normal force (), not a vertical one.
- Distinguish Static Friction from its Maximum Limit
Static friction satisfies ; it equals whatever force is needed to maintain equilibrium until is reached.
Compare with . If , then .
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify horizontal balance: .
Identify vertical balance: as long as .
For , compute . Because , the actual friction is upward.
For the minimum pushing force, set threshold .
(a) Horizontal: inward, outward; Vertical: downward, upward. (b) upward. (c) .
Lock it in
What does the formula actually represent for an object in contact with a rough surface?
It represents the maximum possible static friction force () before slipping begins, not necessarily the actual friction force acting on the object.
Similar question
A block of mass is held against a vertical wall by a horizontal force . The coefficients of friction are and . Take . Determine whether the block slips and find the magnitude and direction of the friction force.
Answer
The block does not slip, and upward. First, calculate weight . Next, find maximum static friction . Because , the block remains at rest, so static friction balances gravity: directed upward.
A box rests on a horizontal floor where and . A horizontal pulling force of is applied to the box. Take . (a) What is the actual friction force acting on the box? (b) What minimum horizontal force is needed to start the box moving?
Answer
(a) opposite the pull; (b) . The normal force is . The maximum static friction is . Since the applied pull , the box remains stationary and . Slipping requires exceeding .
A textbook of mass is held against a vertical wall with a horizontal pushing force . The coefficients of friction are and . Take . Determine whether the book stays at rest or slides down the wall, and calculate the magnitude of the resulting friction force.
Answer
The book slides down the wall, and upward. Downward weight is . The maximum static friction is . Because , static friction cannot hold the book and it accelerates downward. The surface transitions to kinetic friction: upward.