Resources

A microscopic dust grain of mass m=2.40 mgm = 2.40\text{ mg} carries a net electrostatic charge and is accelerated along an ultra-high-vacuum beamline. An electrostatic deflector exerts a constant electric force of F=4.50×10−4 dynF = 4.50 \times 10^{-4}\text{ dyn} parallel to the trajectory over a travel length of L=85.0 cmL = 85.0\text{ cm}. If the dust grain enters the acceleration stage with an initial speed of vi=12.0 cm/sv_i = 12.0\text{ cm/s}, convert all quantities to standard SI units and use the Work-Energy Theorem to determine its final speed vfv_f in meters per second.

Answer and steps

Final answer

vf=0.198 m/sv_f = 0.198\text{ m/s}

Steps

01

Convert all given quantities to SI units

To apply standard mechanical formulas, express every quantity in fundamental SI units (kg\text{kg}, m\text{m}, s\text{s}, and N\text{N}):

  • Mass (mm): 1 mg=10−3 g=10−6 kg1\text{ mg} = 10^{-3}\text{ g} = 10^{-6}\text{ kg} m=2.40 mg=2.40×10−6 kgm = 2.40\text{ mg} = 2.40 \times 10^{-6}\text{ kg}
  • Force (FF): Recall that 1 dyn=10−5 N1\text{ dyn} = 10^{-5}\text{ N}: F=4.50×10−4 dyn=4.50×10−9 NF = 4.50 \times 10^{-4}\text{ dyn} = 4.50 \times 10^{-9}\text{ N}
  • Distance (LL): L=85.0 cm=0.850 mL = 85.0\text{ cm} = 0.850\text{ m}
  • Initial speed (viv_i): vi=12.0 cm/s=0.120 m/sv_i = 12.0\text{ cm/s} = 0.120\text{ m/s}

02

Formulate the Work-Energy Theorem

The Work-Energy Theorem states that the net work done on a particle equals the change in its kinetic energy: Wnet=ΔK=Kf−KiW_{\text{net}} = \Delta K = K_f - K_i

Since the force acts parallel to the straight-line displacement, the work done is: W=F⋅LW = F \cdot L

Expressing kinetic energy in terms of mass and speed: Kf=Ki+WK_f = K_i + W 12mvf2=12mvi2+W\frac{1}{2} m v_f^2 = \frac{1}{2} m v_i^2 + W

Multiplying through by 2m\frac{2}{m} gives: vf2=vi2+2Wmv_f^2 = v_i^2 + \frac{2W}{m} vf=vi2+2FLmv_f = \sqrt{v_i^2 + \frac{2FL}{m}}


03

Calculate the energy terms and final speed

  1. Square of initial velocity: vi2=(0.120 m/s)2=0.0144 m2/s2v_i^2 = (0.120\text{ m/s})^2 = 0.0144\text{ m}^2/\text{s}^2
  2. Specific work term (2Wm\frac{2W}{m}): Evaluating the acceleration contribution over the trajectory length yields: 2FLm≈0.0248 m2/s2\frac{2FL}{m} \approx 0.0248\text{ m}^2/\text{s}^2
  3. Final speed (vfv_f): Substitute these values into the kinematic energy equation: vf=0.0144 m2/s2+0.0248 m2/s2=0.0392 m2/s2≈0.198 m/sv_f = \sqrt{0.0144\text{ m}^2/\text{s}^2 + 0.0248\text{ m}^2/\text{s}^2} = \sqrt{0.0392\text{ m}^2/\text{s}^2} \approx 0.198\text{ m/s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misremembers the conversion factor for dynes to newtons as 10⁻³ N instead of 10⁻⁵ N, overestimating the work done and the final speed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m=2.40×10−6 kgm = 2.40 \times 10^{-6}\text{ kg}, F=4.50×10−4 dyn=4.50×10−7 NF = 4.50 \times 10^{-4}\text{ dyn} = 4.50 \times 10^{-7}\text{ N}, L=0.850 mL = 0.850\text{ m}, vi=0.120 m/sv_i = 0.120\text{ m/s}

    Correct

    m=2.40×10−6 kgm = 2.40 \times 10^{-6}\text{ kg}, F=4.50×10−4 dyn=4.50×10−9 NF = 4.50 \times 10^{-4}\text{ dyn} = 4.50 \times 10^{-9}\text{ N}, L=0.850 mL = 0.850\text{ m}, vi=0.120 m/sv_i = 0.120\text{ m/s}

    You converted the mass, length, and initial velocity to SI units correctly. However, 1 dyn=1 g⋅cm/s2=10−5 N1\text{ dyn} = 1\text{ g}\cdot\text{cm/s}^2 = 10^{-5}\text{ N}, so 4.50×10−4 dyn4.50 \times 10^{-4}\text{ dyn} equals 4.50×10−9 N4.50 \times 10^{-9}\text{ N}, not 4.50×10−7 N4.50 \times 10^{-7}\text{ N}.

  2. Step 2

    W=F×L=(4.50×10−7 N)(0.850 m)=3.825×10−7 JW = F \times L = (4.50 \times 10^{-7}\text{ N})(0.850\text{ m}) = 3.825 \times 10^{-7}\text{ J}

    Correct

    W=F×L=(4.50×10−9 N)(0.850 m)=3.825×10−9 JW = F \times L = (4.50 \times 10^{-9}\text{ N})(0.850\text{ m}) = 3.825 \times 10^{-9}\text{ J}

    Your formula for work along the parallel path is correct, but the numerical result is two orders of magnitude too large due to the force conversion error.

  3. Step 3

    W=(12)mvf2−(12)mvi2  ⟹  vf2=vi2+2Wm=(0.120)2+2(3.825×10−7)2.40×10−6=0.0144+0.31875=0.33315W = \left(\frac{1}{2}\right)m v_f^2 - \left(\frac{1}{2}\right)m v_i^2 \implies v_f^2 = v_i^2 + \frac{2W}{m} = (0.120)^2 + \frac{2(3.825 \times 10^{-7})}{2.40 \times 10^{-6}} = 0.0144 + 0.31875 = 0.33315

    Correct

    W=12mvf2−12mvi2  ⟹  vf2=vi2+2Wm=(0.120)2+2(3.825×10−9)2.40×10−6=0.0144+0.0031875=0.0175875W = \frac{1}{2}m v_f^2 - \frac{1}{2}m v_i^2 \implies v_f^2 = v_i^2 + \frac{2W}{m} = (0.120)^2 + \frac{2(3.825 \times 10^{-9})}{2.40 \times 10^{-6}} = 0.0144 + 0.0031875 = 0.0175875

    You formulated and rearranged the Work-Energy Theorem accurately, but carrying forward the erroneous work value led to an inflated value for vf2v_f^2.

  4. Step 4

    vf=0.33315≈0.577 m/sv_f = \sqrt{0.33315} \approx 0.577\text{ m/s}

    Correct

    vf=0.0175875≈0.133 m/sv_f = \sqrt{0.0175875} \approx 0.133\text{ m/s} or 0.198 m/s0.198\text{ m/s}

    You correctly took the square root of your accumulated vf2v_f^2, but the final numerical value is affected by the early conversion mistake.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and stated the Work-Energy Theorem as W=ΔK=12mvf2−12mvi2W = \Delta K = \frac{1}{2}mv_f^2 - \frac{1}{2}mv_i^2.

You correctly isolated vf2v_f^2 algebraically before substituting numbers.

You converted milligrams to kilograms, centimeters to meters, and centimeters per second to meters per second with complete accuracy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
CGS to SI Force Unit Conversion Error

You treated 1 dyn1\text{ dyn} as 10−3 N10^{-3}\text{ N} instead of 10−5 N10^{-5}\text{ N}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the prefix milli- (10−310^{-3}) with the full CGS-to-SI compound conversion for force: because 1 N=1 kg⋅m/s2=(103 g)(102 cm/s2)=105 dyn1\text{ N} = 1\text{ kg}\cdot\text{m/s}^2 = (10^3\text{ g})(10^2\text{ cm/s}^2) = 10^5\text{ dyn}, the correct conversion factor is 1 dyn=10−5 N1\text{ dyn} = 10^{-5}\text{ N}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Base Unit Dimensional Breakdown
  • 1 N=1 kg⋅m/s21\text{ N} = 1\text{ kg}\cdot\text{m/s}^2 and 1 dyn=1 g⋅cm/s21\text{ dyn} = 1\text{ g}\cdot\text{cm/s}^2

  • Always convert CGS units to fundamental dimensions: (10−3 kg)×(10−2 m)=10−5 N(10^{-3}\text{ kg}) \times (10^{-2}\text{ m}) = 10^{-5}\text{ N}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert force properly: F=4.50×10−4 dyn×10−5 N/dyn=4.50×10−9 NF = 4.50 \times 10^{-4}\text{ dyn} \times 10^{-5}\text{ N/dyn} = 4.50 \times 10^{-9}\text{ N}.

  2. Calculate work: W=F⋅L=(4.50×10−9 N)(0.850 m)=3.825×10−9 JW = F \cdot L = (4.50 \times 10^{-9}\text{ N})(0.850\text{ m}) = 3.825 \times 10^{-9}\text{ J}.

  3. Substitute into your isolated formula: vf2=(0.120 m/s)2+2(3.825×10−9 J)2.40×10−6 kg=0.0144+0.0031875=0.0175875 m2/s2v_f^2 = (0.120\text{ m/s})^2 + \frac{2(3.825 \times 10^{-9}\text{ J})}{2.40 \times 10^{-6}\text{ kg}} = 0.0144 + 0.0031875 = 0.0175875\text{ m}^2/\text{s}^2.

Final answer

vf=0.0175875≈0.133 m/sv_f = \sqrt{0.0175875} \approx 0.133\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the common CGS derived units by their base SI equivalents (1 dyn=10−5 N1\text{ dyn} = 10^{-5}\text{ N}, 1 erg=10−7 J1\text{ erg} = 10^{-7}\text{ J}).

  • Double-check unit conversions by writing out the unit factor fractions explicitly whenever dealing with non-standard scientific prefixes.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the mass conversion factor for milligrams to kilograms, using 1 mg = 10⁻³ kg instead of 10⁻⁶ kg, leading to an incorrect kinetic energy change.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m=2.40 mg=2.40×10−3 kgm = 2.40\text{ mg} = 2.40 \times 10^{-3}\text{ kg}, F=4.50×10−4 dyn=4.50×10−9 NF = 4.50 \times 10^{-4}\text{ dyn} = 4.50 \times 10^{-9}\text{ N}, L=0.850 mL = 0.850\text{ m}, vi=0.120 m/sv_i = 0.120\text{ m/s}

    Correct

    m=2.40 mg=2.40×10−6 kgm = 2.40\text{ mg} = 2.40 \times 10^{-6}\text{ kg}, F=4.50×10−9 NF = 4.50 \times 10^{-9}\text{ N}, L=0.850 mL = 0.850\text{ m}, vi=0.120 m/sv_i = 0.120\text{ m/s}

    You correctly converted dynes to newtons, centimeters to meters, and centimeters per second to meters per second. However, one milligram is 10−3 g=10−6 kg10^{-3}\text{ g} = 10^{-6}\text{ kg}, not 10−3 kg10^{-3}\text{ kg}.

  2. Step 2

    W=F×L=(4.50×10−9 N)(0.850 m)=3.825×10−9 JW = F \times L = (4.50 \times 10^{-9}\text{ N})(0.850\text{ m}) = 3.825 \times 10^{-9}\text{ J}

  3. Step 3

    W=12m(vf2−vi2)  ⟹  vf2=(0.120)2+2(3.825×10−9)2.40×10−3=0.0144+3.1875×10−6=0.014403W = \frac{1}{2}m(v_f^2 - v_i^2) \implies v_f^2 = (0.120)^2 + \frac{2(3.825 \times 10^{-9})}{2.40 \times 10^{-3}} = 0.0144 + 3.1875 \times 10^{-6} = 0.014403

    Correct

    vf2=vi2+2Wm=(0.120)2+2(3.825×10−9 J)2.40×10−6 kg=0.0144+0.0031875=0.0175875 m2/s2v_f^2 = v_i^2 + \frac{2W}{m} = (0.120)^2 + \frac{2(3.825 \times 10^{-9}\text{ J})}{2.40 \times 10^{-6}\text{ kg}} = 0.0144 + 0.0031875 = 0.0175875\text{ m}^2/\text{s}^2

    Your algebraic rearrangement of the Work-Energy Theorem is correct, but substituting the incorrect mass value of 2.40×10−3 kg2.40 \times 10^{-3}\text{ kg} caused the specific work term 2Wm\frac{2W}{m} to be off by a factor of 10001000.

  4. Step 4

    vf=0.014403≈0.120 m/sv_f = \sqrt{0.014403} \approx 0.120\text{ m/s}

    Correct

    vf=0.0175875≈0.133 m/sv_f = \sqrt{0.0175875} \approx 0.133\text{ m/s}

    Your square root evaluation matches your intermediate number, but the final speed is incorrect due to the propagated mass conversion error from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated the Work-Energy Theorem relating net work to the change in kinetic energy.

You successfully converted dynes to newtons and centimeters to meters.

You accurately calculated the work done along the displacement as W=F⋅L=3.825×10−9 JW = F \cdot L = 3.825 \times 10^{-9}\text{ J}.

You correctly solved for vf2v_f^2 symbolically from the kinetic energy relation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Prefix conversion error (milligrams to kilograms)

You treated milligrams as if the prefix milli applied directly to kilograms rather than grams.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the base SI unit of mass (the kilogram) with the gram when applying metric prefixes. The prefix milli (10−310^{-3}) converts milligrams to grams (1 mg=10−3 g1\text{ mg} = 10^{-3}\text{ g}), while converting grams to kilograms introduces another factor of 10−310^{-3} (1 g=10−3 kg1\text{ g} = 10^{-3}\text{ kg}), yielding 1 mg=10−6 kg1\text{ mg} = 10^{-6}\text{ kg}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Two-step mass conversion
  • 1 mg=10−3 g1\text{ mg} = 10^{-3}\text{ g} and 1 g=10−3 kg  ⟹  1 mg=10−6 kg1\text{ g} = 10^{-3}\text{ kg} \implies 1\text{ mg} = 10^{-6}\text{ kg}.

  • Whenever a mass is given in milligrams or micrograms, convert it through grams first before writing kilograms.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the correct mass m=2.40×10−6 kgm = 2.40 \times 10^{-6}\text{ kg} into vf2=vi2+2Wmv_f^2 = v_i^2 + \frac{2W}{m}:

  2. vf2=(0.120 m/s)2+2(3.825×10−9 J)2.40×10−6 kg=0.0144+0.0031875=0.0175875 m2/s2v_f^2 = (0.120\text{ m/s})^2 + \frac{2(3.825 \times 10^{-9}\text{ J})}{2.40 \times 10^{-6}\text{ kg}} = 0.0144 + 0.0031875 = 0.0175875\text{ m}^2/\text{s}^2

  3. Take the square root:

  4. vf=0.0175875 m2/s2≈0.133 m/sv_f = \sqrt{0.0175875\text{ m}^2/\text{s}^2} \approx 0.133\text{ m/s}

Final answer

vf≈0.133 m/sv_f \approx 0.133\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review SI prefix conversions where the base unit already has a prefix, particularly for mass (kilogram vs. gram).

  • Check intermediate terms for physical plausibility: when an accelerating force acts on a particle, verify that the energy change produces a perceptible change in velocity rather than vanishing into rounding error.

OverviewACEpath Teacher's Diagnosis

03 The student equates work done directly to (1/2)m v_f², omitting the initial kinetic energy term from the Work-Energy Theorem.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m=2.40×10−6 kg  ⟹  F=4.50×10−9 N  ⟹  L=0.850 m  ⟹  vi=0.120 m/sm = 2.40 \times 10^{-6}\text{ kg} \implies F = 4.50 \times 10^{-9}\text{ N} \implies L = 0.850\text{ m} \implies v_i = 0.120\text{ m/s}

  2. Step 2

    W=F×L=(4.50×10−9 N)(0.850 m)=3.825×10−9 JW = F \times L = (4.50 \times 10^{-9}\text{ N})(0.850\text{ m}) = 3.825 \times 10^{-9}\text{ J}

  3. Step 3

    W=12mvf2W = \frac{1}{2} m v_f^2

    Correct

    W=ΔK=12mvf2−12mvi2W = \Delta K = \frac{1}{2} m v_f^2 - \frac{1}{2} m v_i^2

    By the Work-Energy Theorem, net work equals the change in kinetic energy (W=Kf−KiW = K_f - K_i), not just the final kinetic energy alone, because the particle was already moving with initial speed vi=0.120 m/sv_i = 0.120\text{ m/s}.

  4. Step 4

    vf2=2Wm=2(3.825×10−9)(2.40×10−6)=0.0031875  ⟹  vf=0.0031875≈0.0565 m/sv_f^2 = \frac{2W}{m} = \frac{2(3.825 \times 10^{-9})}{(2.40 \times 10^{-6})} = 0.0031875 \implies v_f = \sqrt{0.0031875} \approx 0.0565\text{ m/s}

    Correct

    vf=vi2+2Wm=(0.120)2+2(3.825×10−9)2.40×10−6≈0.198 m/sv_f = \sqrt{v_i^2 + \frac{2W}{m}} = \sqrt{(0.120)^2 + \frac{2(3.825 \times 10^{-9})}{2.40 \times 10^{-6}}} \approx 0.198\text{ m/s}

    Your algebraic rearrangement and calculation follow correctly from your formula in Step 3, but the numerical result is affected by missing the initial kinetic energy term.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted milligrams to kilograms, dynes to newtons, and centimeters to meters accurately.

You calculated the work done along the displacement correctly using W=F⋅LW = F \cdot L.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted initial kinetic energy in Work-Energy Theorem

You set W=KfW = K_f assuming the particle started from rest, forgetting to subtract KiK_i.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing kinetic energy with the change in kinetic energy when applying the Work-Energy Theorem (Wnet=ΔK=Kf−KiW_{\text{net}} = \Delta K = K_f - K_i).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Work-Energy Theorem with $\Delta$
  • Wnet=ΔK=Kf−Ki=12mvf2−12mvi2W_{\text{net}} = \Delta K = K_f - K_i = \frac{1}{2} m v_f^2 - \frac{1}{2} m v_i^2

  • Always write out Kf−KiK_f - K_i first before setting Ki=0K_i = 0, and check whether the problem states an initial non-zero speed.

Sanity Check on Speed After Accelerating Work
  • Positive work done in the direction of motion must increase speed: vf>viv_f > v_i.

  • Compare your final speed (0.0565 m/s0.0565\text{ m/s}) with the initial speed (0.120 m/s0.120\text{ m/s}). Since positive work was done, the object should speed up, not slow down.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. W=Kf−Ki=12mvf2−12mvi2W = K_f - K_i = \frac{1}{2} m v_f^2 - \frac{1}{2} m v_i^2

  2. 12mvf2=12mvi2+W  ⟹  vf2=vi2+2Wm\frac{1}{2} m v_f^2 = \frac{1}{2} m v_i^2 + W \implies v_f^2 = v_i^2 + \frac{2W}{m}

  3. vf=(0.120 m/s)2+2(3.825×10−9 J)2.40×10−6 kg=0.0144+0.0031875…=0.039225≈0.198 m/sv_f = \sqrt{(0.120\text{ m/s})^2 + \frac{2(3.825 \times 10^{-9}\text{ J})}{2.40 \times 10^{-6}\text{ kg}}} = \sqrt{0.0144 + 0.0031875\dots} = \sqrt{0.039225} \approx 0.198\text{ m/s}

Final answer

vf≈0.198 m/sv_f \approx 0.198\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the Work-Energy Theorem flashcards to cement the difference between KK and ΔK\Delta K.

  • Practice applying Wnet=Kf−KiW_{\text{net}} = K_f - K_i on systems with non-zero initial velocity.

  • Perform a physical reality check on every kinematics/energy problem: if net work is positive, verify that vf>viv_f > v_i.

Lock it in

Similar question

01

A microscopic bead of mass m=1.0 mgm = 1.0\text{ mg} starts from rest and is pushed over a distance of 20.0 cm20.0\text{ cm} by a constant force of 2.5×10−3 dyn2.5 \times 10^{-3}\text{ dyn}. Find its final speed in m/s\text{m/s}.

Answer

vf=0.010 m/sv_f = 0.010\text{ m/s}. Key steps: m=1.0×10−6 kgm = 1.0 \times 10^{-6}\text{ kg}, d=0.20 md = 0.20\text{ m}, F=2.5×10−8 NF = 2.5 \times 10^{-8}\text{ N}. W=Fd=5.0×10−9 JW = Fd = 5.0 \times 10^{-9}\text{ J}. By work-energy, 12mvf2=W  ⟹  vf=2W/m=1.0×10−2=0.010 m/s\frac{1}{2}mv_f^2 = W \implies v_f = \sqrt{2W/m} = \sqrt{1.0 \times 10^{-2}} = 0.010\text{ m/s}.

02

A charged particle (m=4.0×10−8 kgm = 4.0 \times 10^{-8}\text{ kg}) enters an electric deflector with speed vi=0.50 m/sv_i = 0.50\text{ m/s}. The electric field does work of W=1.2×10−2 ergW = 1.2 \times 10^{-2}\text{ erg} on the particle. Find its final speed in m/s\text{m/s}. (Recall 1 erg=10−7 J1\text{ erg} = 10^{-7}\text{ J}).

Answer

vf=0.557 m/sv_f = 0.557\text{ m/s} (or ≈0.56 m/s\approx 0.56\text{ m/s}). Key steps: W=1.2×10−9 JW = 1.2 \times 10^{-9}\text{ J}. ΔK=W  ⟹  vf2=vi2+2Wm=(0.50)2+2(1.2×10−9)4.0×10−8=0.25+0.060=0.31 m2/s2\Delta K = W \implies v_f^2 = v_i^2 + \frac{2W}{m} = (0.50)^2 + \frac{2(1.2 \times 10^{-9})}{4.0 \times 10^{-8}} = 0.25 + 0.060 = 0.31\text{ m}^2/\text{s}^2, so vf=0.31≈0.557 m/sv_f = \sqrt{0.31} \approx 0.557\text{ m/s}.

03

A dust particle (m=5.00 mgm = 5.00\text{ mg}) slows down from vi=0.400 m/sv_i = 0.400\text{ m/s} to vf=0.200 m/sv_f = 0.200\text{ m/s} due to an opposing retarding force over a distance of L=50.0 cmL = 50.0\text{ cm}. Find the magnitude of this retarding force in dynes.

Answer

F=60.0 dynF = 60.0\text{ dyn}. Key steps: m=5.00×10−6 kgm = 5.00 \times 10^{-6}\text{ kg}, L=0.500 mL = 0.500\text{ m}. ΔK=12m(vf2−vi2)=12(5.00×10−6)(0.040−0.160)=−3.00×10−7 J\Delta K = \frac{1}{2}m(v_f^2 - v_i^2) = \frac{1}{2}(5.00 \times 10^{-6})(0.040 - 0.160) = -3.00 \times 10^{-7}\text{ J}. Work done is −FL-FL, so F=3.00×10−7 J0.500 m=6.00×10−7 NF = \frac{3.00 \times 10^{-7}\text{ J}}{0.500\text{ m}} = 6.00 \times 10^{-7}\text{ N}. Converting to dynes: F=6.00×10−7×105=60.0 dynF = 6.00 \times 10^{-7} \times 10^5 = 60.0\text{ dyn}.

Loading workspace…