Resources

A closed DC circuit loop contains an ideal battery with an electromotive force of E=15.0 V\mathcal{E} = 15.0\text{ V} and two ohmic resistors, R1=120 ΩR_1 = 120\,\Omega and R2=180 ΩR_2 = 180\,\Omega, connected in series. Node AA is located between the positive terminal of the battery and R1R_1, node BB is located between R1R_1 and R2R_2, and node CC is connected directly to the negative terminal of the battery. Defining the electric potential at node CC as the reference ground (VC=0.00 VV_C = 0.00\text{ V}) and traversing the loop in the direction of conventional current, calculate the directed electric potential difference VCB=VC−VBV_{CB} = V_C - V_B in volts (V\text{V}).

Answer and steps

Final answer

−9.00 V-9.00\text{ V}

Steps

01

Find the total equivalent resistance of the loop

To find the directed electric potential difference VCB=VC−VBV_{CB} = V_C - V_B, we determine the current flowing through the circuit and the electric potential at node BB.

The two resistors R1R_1 and R2R_2 are connected in series along a single closed path. The total equivalent resistance ReqR_{\text{eq}} is: Req=R1+R2=120 Ω+180 Ω=300 ΩR_{\text{eq}} = R_1 + R_2 = 120\text{ }\Omega + 180\text{ }\Omega = 300\text{ }\Omega

02

Calculate the circuit current using Ohm's law

The battery is ideal, meaning its internal resistance is zero. According to Ohm's law, the steady conventional current II circulating clockwise from the positive terminal through node AA, resistor R1R_1, node BB, resistor R2R_2, and back to node CC is: I=EReq=15.0 V300 Ω=0.050 AI = \frac{\mathcal{E}}{R_{\text{eq}}} = \frac{15.0\text{ V}}{300\text{ }\Omega} = 0.050\text{ A}

03

Determine the electric potential at node BB

The negative terminal connects to node CC, which is set as the reference ground: VC=0.00 VV_C = 0.00\text{ V}

Conventional current flows from higher potential to lower potential through a resistor. Because the current flows from node BB through resistor R2R_2 to node CC, the potential drop across R2R_2 is: VB−VC=IR2=(0.050 A)(180 Ω)=9.00 VV_B - V_C = I R_2 = (0.050\text{ A})(180\text{ }\Omega) = 9.00\text{ V}

Substitute VC=0.00 VV_C = 0.00\text{ V}: VB−0.00 V=9.00 V  ⟹  VB=9.00 VV_B - 0.00\text{ V} = 9.00\text{ V} \implies V_B = 9.00\text{ V}

Alternatively, using the voltage divider formula: VB=E⋅R2R1+R2=15.0 V⋅180 Ω300 Ω=9.00 VV_B = \mathcal{E} \cdot \frac{R_2}{R_1 + R_2} = 15.0\text{ V} \cdot \frac{180\text{ }\Omega}{300\text{ }\Omega} = 9.00\text{ V}

04

Compute the directed potential difference VCBV_{CB}

The question specifies the difference VCB=VC−VBV_{CB} = V_C - V_B: VCB=0.00 V−9.00 V=−9.00 VV_{CB} = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}

Common Pitfall: A potential difference designated as VCBV_{CB} is strictly defined as the final potential minus the initial potential (VC−VBV_C - V_B). Do not confuse it with the magnitude of the voltage drop across R2R_2 (VBC=VB−VC=+9.00 VV_{BC} = V_B - V_C = +9.00\text{ V}). Because node CC is at a lower electric potential than node BB, VCBV_{CB} must be negative.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student reverses the order of subtraction or treats potential difference as a magnitude, calculating V_BC = V_B - V_C instead of V_CB = V_C - V_B.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Req=120+180=300 ΩR_{eq} = 120 + 180 = 300\text{ }\Omega

  2. Step 2

    I=15.0300=0.050 AI = \frac{15.0}{300} = 0.050\text{ A}

  3. Step 3

    VB=0.050∗180=9.00 VV_B = 0.050 * 180 = 9.00\text{ V}

  4. Step 4

    VCB=VB−VC=9.00−0.00=9.00 VV_{CB} = V_B - V_C = 9.00 - 0.00 = 9.00\text{ V}

    Correct

    VCB=VC−VB=0.00 V−9.00 V=−9.00 VV_{CB} = V_C - V_B = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}

    In standard double-subscript notation and as explicitly stated in the problem, VCBV_{CB} is defined as VC−VBV_C - V_B. You computed VB−VCV_B - V_C (VBCV_{BC}) instead, reversing the sign.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the total equivalent resistance for resistors in series.

You applied Ohm's law properly to find the circuit current.

You accurately calculated the potential at node B with respect to ground.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Subscript notation reversal

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the directed potential difference VCBV_{CB} as VB−VCV_B - V_C (or as an unsigned magnitude drop) rather than following the formal double-subscript definition Vxy=Vx−VyV_{xy} = V_x - V_y.

REASONING PATH
Your ACEpath teacher’s suggested approach
Double-Subscript Convention
  • For any two nodes xx and yy, the potential difference is defined as Vxy=Vx−VyV_{xy} = V_x - V_y (first subscript minus second subscript).

  • Always write the expansion Vxy=Vx−VyV_{xy} = V_x - V_y explicitly before substituting numerical values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the required quantity from the problem definition: VCB=VC−VBV_{CB} = V_C - V_B.

  2. Substitute the known node potentials: VC=0.00 VV_C = 0.00\text{ V} and VB=9.00 VV_B = 9.00\text{ V}.

  3. Calculate the signed difference: VCB=0.00 V−9.00 V=−9.00 VV_{CB} = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}.

Final answer

−9.00 V-9.00\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the double-subscript potential convention VAB=VA−VBV_{AB} = V_A - V_B.

  • Practice distinguishing between absolute node potentials, voltage drops across components, and directed potential differences.

OverviewACEpath Teacher's Diagnosis

02 The student confuses resistor R_1 with R_2 when finding the potential drop from node A to node B, inadvertently computing V_C - V_A or using R_1 to find V_B.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Req=120+180=300 Ω  ⟹  I=15.0300=0.050 AR_{\text{eq}} = 120 + 180 = 300\text{ }\Omega \implies I = \frac{15.0}{300} = 0.050\text{ A}

  2. Step 2

    VB=I⋅R1=0.050⋅120=6.00 VV_B = I \cdot R_1 = 0.050 \cdot 120 = 6.00\text{ V}

    Correct

    VB=VC+IR2=0.00 V+(0.050 A)(180 Ω)=9.00 VV_B = V_C + I R_2 = 0.00\text{ V} + (0.050\text{ A})(180\text{ }\Omega) = 9.00\text{ V}

    You computed the potential drop across resistor R1R_1 (VA−VB=6.00 VV_A - V_B = 6.00\text{ V}) and assigned that value directly to VBV_B. Because node BB is separated from reference ground (VC=0.00 VV_C = 0.00\text{ V}) by resistor R2R_2, the potential at node BB is determined by the drop across R2R_2: VB−VC=IR2=9.00 VV_B - V_C = I R_2 = 9.00\text{ V}, which gives VB=9.00 VV_B = 9.00\text{ V} (or VB=VA−IR1=15.0 V−6.00 V=9.00 VV_B = V_A - I R_1 = 15.0\text{ V} - 6.00\text{ V} = 9.00\text{ V}).

  3. Step 3

    VCB=VC−VB=0.00−6.00=−6.00 VV_{CB} = V_C - V_B = 0.00 - 6.00 = -6.00\text{ V}

    Correct

    VCB=VC−VB=0.00 V−9.00 V=−9.00 VV_{CB} = V_C - V_B = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}

    You correctly applied the definition VCB=VC−VBV_{CB} = V_C - V_B, but your result was offset by the incorrect value of VBV_B from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the equivalent resistance of the two series resistors.

You used Ohm's law properly to determine the loop current.

You correctly set up the directed difference formula as VCB=VC−VBV_{CB} = V_C - V_B.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Node potential vs. element voltage drop confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the voltage drop across the first resistor (VA−VBV_A - V_B) as the absolute potential at node BB, overlooking that the potential at node AA is 15.0 V15.0\text{ V} and node BB is referenced to ground (VC=0.00 VV_C = 0.00\text{ V}) through resistor R2R_2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Path Rule
  • The absolute potential at any node XX is the directed sum of potential changes from reference ground (0 V0\text{ V}) to node XX: VX=Vref+∑ΔVV_X = V_{\text{ref}} + \sum \Delta V.

  • Trace a path from node CC (0 V0\text{ V}) to node BB. Moving against conventional current through R2R_2 gains potential: VB=VC+IR2V_B = V_C + I R_2.

Voltage Divider / Drop Check
  • For a series string connected between VhighV_{\text{high}} and 0 V0\text{ V}, intermediate node potentials equal Vhigh−ΔVprecedingV_{\text{high}} - \Delta V_{\text{preceding}} or 0 V+ΔVfollowing0\text{ V} + \Delta V_{\text{following}}.

  • Verify VBV_B from both directions: VB=15.0 V−IR1=9.00 VV_B = 15.0\text{ V} - I R_1 = 9.00\text{ V}, and VB=0.00 V+IR2=9.00 VV_B = 0.00\text{ V} + I R_2 = 9.00\text{ V}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine VBV_B relative to reference ground VC=0.00 VV_C = 0.00\text{ V}: moving from CC to BB goes upstream against current through R2R_2, so VB=VC+IR2=0.00 V+(0.050 A)(180 Ω)=9.00 VV_B = V_C + I R_2 = 0.00\text{ V} + (0.050\text{ A})(180\text{ }\Omega) = 9.00\text{ V}.

  2. Compute the directed potential difference: VCB=VC−VB=0.00 V−9.00 V=−9.00 VV_{CB} = V_C - V_B = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}.

Final answer

−9.00 V-9.00\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice tracing electric potential step-by-step from the defined ground node along the circuit path.

  • Always double-check intermediate node potentials by calculating from both the positive and negative supply terminals.

OverviewACEpath Teacher's Diagnosis

03 The student treats the two resistors as connected in parallel rather than in series when calculating equivalent resistance and current.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    1Req=1120+1180=5360  ⟹  Req=72 Ω\frac{1}{R_{\text{eq}}} = \frac{1}{120} + \frac{1}{180} = \frac{5}{360} \implies R_{\text{eq}} = 72\text{ }\Omega

    Correct

    Req=R1+R2=120 Ω+180 Ω=300 ΩR_{\text{eq}} = R_1 + R_2 = 120\text{ }\Omega + 180\text{ }\Omega = 300\text{ }\Omega

    Because R1R_1 and R2R_2 are connected end-to-end along a single loop with no junctions, they are in series, so their resistances add directly: Req=R1+R2R_{\text{eq}} = R_1 + R_2.

  2. Step 2

    I=15.072=0.208 AI = \frac{15.0}{72} = 0.208\text{ A}

    Correct

    I=EReq=15.0 V300 Ω=0.050 AI = \frac{\mathcal{E}}{R_{\text{eq}}} = \frac{15.0\text{ V}}{300\text{ }\Omega} = 0.050\text{ A}

    You correctly applied Ohm's law I=EReqI = \frac{\mathcal{E}}{R_{\text{eq}}}, but the value is affected by your earlier calculation of ReqR_{\text{eq}}.

  3. Step 3

    VB=0.208⋅180=37.44 VV_B = 0.208 \cdot 180 = 37.44\text{ V}

    Correct

    VB=IR2=0.050 A⋅180 Ω=9.00 VV_B = I R_2 = 0.050\text{ A} \cdot 180\text{ }\Omega = 9.00\text{ V}

    You correctly identified that the potential at node BB relative to ground is the voltage drop across R2R_2, but using the inflated current yielded a potential greater than the battery's total EMF.

  4. Step 4

    VCB=VC−VB=0.00−37.44=−37.44 VV_{CB} = V_C - V_B = 0.00 - 37.44 = -37.44\text{ V}

    Correct

    VCB=VC−VB=0.00 V−9.00 V=−9.00 VV_{CB} = V_C - V_B = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}

    You correctly evaluated the directed difference as VC−VBV_C - V_B, but the numerical value inherits the error from previous steps.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Ohm's law to relate current, EMF, and total resistance.

You correctly recognized that the potential at node BB is determined by the drop across resistor R2R_2 from ground.

You correctly set up the directed potential difference formula VCB=VC−VBV_{CB} = V_C - V_B.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Parallel formula used for series resistors

You applied the reciprocal formula for parallel resistors to a single series loop.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the series combination rule (Req=R1+R2R_{\text{eq}} = R_1 + R_2) with the parallel combination rule (1Req=1R1+1R2\frac{1}{R_{\text{eq}}} = \frac{1}{R_1} + \frac{1}{R_2}). A sanity check is that no node potential in a single-source DC resistive loop can exceed the battery EMF (15.0 V15.0\text{ V}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Path Connectivity
  • Components sharing a single unbroken current path with no branching nodes are strictly in series.

  • Trace the current path: if all current must pass through one component and then directly through the next, add their resistances directly.

Voltage Bound Sanity Check
  • In a simple single-battery resistive circuit, intermediate node potentials must stay between 0 V0\text{ V} and the battery EMF.

  • Check whether intermediate potentials like VB=37.44 VV_B = 37.44\text{ V} exceed the source EMF of 15.0 V15.0\text{ V}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find total series resistance: Req=R1+R2=120 Ω+180 Ω=300 ΩR_{\text{eq}} = R_1 + R_2 = 120\text{ }\Omega + 180\text{ }\Omega = 300\text{ }\Omega.

  2. Calculate loop current: I=EReq=15.0 V300 Ω=0.050 AI = \frac{\mathcal{E}}{R_{\text{eq}}} = \frac{15.0\text{ V}}{300\text{ }\Omega} = 0.050\text{ A}.

  3. Determine potential at node BB: VB=VC+IR2=0.00 V+(0.050 A)(180 Ω)=9.00 VV_B = V_C + I R_2 = 0.00\text{ V} + (0.050\text{ A})(180\text{ }\Omega) = 9.00\text{ V}.

  4. Calculate directed difference: VCB=VC−VB=0.00 V−9.00 V=−9.00 VV_{CB} = V_C - V_B = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}.

Final answer

−9.00 V-9.00\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying whether circuit elements share nodes in parallel or share a single branch in series before writing formulas.

  • Perform a sanity check on intermediate voltages to make sure they do not exceed the supply voltage.

Lock it in

Similar question

01

In a single-loop circuit, a 12.0 V12.0\text{ V} battery is connected across two series resistors R1=100 ΩR_1 = 100\text{ }\Omega and R2=300 ΩR_2 = 300\text{ }\Omega. Node XX is between the positive terminal and R1R_1, node YY is between R1R_1 and R2R_2, and node ZZ is connected to the negative terminal (ground, VZ=0.00 VV_Z = 0.00\text{ V}). Calculate the directed potential difference VZY=VZ−VYV_{ZY} = V_Z - V_Y.

Answer

VZY=−9.00 VV_{ZY} = -9.00\text{ V}. Key steps: I=12.0 V/(100+300) Ω=0.030 AI = 12.0\text{ V} / (100 + 300)\text{ }\Omega = 0.030\text{ A}; potential at YY is VY=IR2=0.030 A×300 Ω=9.00 VV_Y = I R_2 = 0.030\text{ A} \times 300\text{ }\Omega = 9.00\text{ V}; then VZY=VZ−VY=0.00 V−9.00 V=−9.00 VV_{ZY} = V_Z - V_Y = 0.00\text{ V} - 9.00\text{ V} = -9.00\text{ V}.

02

Two points PP and QQ along a resistive wire carry a steady current. If the electric potential at PP is −3.50 V-3.50\text{ V} and the electric potential at QQ is +2.50 V+2.50\text{ V}, determine the directed potential difference VPQV_{PQ} and state whether moving from PP to QQ corresponds to a potential rise or drop.

Answer

VPQ=−6.00 VV_{PQ} = -6.00\text{ V}; moving from PP to QQ is a potential rise. Key steps: VPQ=VP−VQ=−3.50 V−(+2.50 V)=−6.00 VV_{PQ} = V_P - V_Q = -3.50\text{ V} - (+2.50\text{ V}) = -6.00\text{ V}. Since VQ>VPV_Q > V_P, going from PP to QQ gains potential.

03

A DC circuit has three nodes: AA, BB, and CC. It is known that VAB=5.00 VV_{AB} = 5.00\text{ V} and VBC=−8.00 VV_{BC} = -8.00\text{ V}. Without knowing individual absolute potentials, evaluate VCAV_{CA}.

Answer

VCA=+3.00 VV_{CA} = +3.00\text{ V}. Key steps: VAC=VAB+VBC=5.00 V+(−8.00 V)=−3.00 VV_{AC} = V_{AB} + V_{BC} = 5.00\text{ V} + (-8.00\text{ V}) = -3.00\text{ V}; since VCA=−VACV_{CA} = -V_{AC}, we have VCA=−(−3.00 V)=+3.00 VV_{CA} = -(-3.00\text{ V}) = +3.00\text{ V}.

Loading workspace…