Resources

Consider an idealized Carnot heat engine operating between a fixed cold sink at TC=295 KT_C = 295\text{ K} and an ultra-high temperature plasma reservoir at THT_H. (a) Determine the asymptotic limit of the thermal efficiency η\eta as TH→∞T_H \to \infty. (b) Calculate the minimum temperature THT_H required for the engine to achieve η=95.0%\eta = 95.0\%.

Answer and steps

Final answer

(a) lim⁡TH→∞η=1.00\lim_{T_H \to \infty} \eta = 1.00 (100%100\%); (b) TH=5900 KT_H = 5900\text{ K}

Steps

Part (a): Asymptotic Limit of Thermal Efficiency

The thermal efficiency η\eta of an idealized Carnot engine operating between a hot reservoir at absolute temperature THT_H and a cold sink at absolute temperature TCT_C is given by:

η=1−TCTH\eta = 1 - \frac{T_C}{T_H}

Here, the cold sink temperature is held constant at TC=295 KT_C = 295\text{ K}. Taking the mathematical limit as the hot reservoir temperature approaches infinity (TH→∞T_H \to \infty):

lim⁡TH→∞η=lim⁡TH→∞(1−TCTH)=1−0=1.00\lim_{T_H \to \infty} \eta = \lim_{T_H \to \infty} \left(1 - \frac{T_C}{T_H}\right) = 1 - 0 = 1.00

Expressed as a percentage, this theoretical upper bound is:

lim⁡TH→∞η=100%\lim_{T_H \to \infty} \eta = 100\%

Physical note: Even with an infinitely hot reservoir, complete conversion of heat to work (η=100%\eta = 100\%) is strictly an asymptotic limit because practical reservoir temperatures are always finite.


Part (b): Minimum Hot Reservoir Temperature for η=95.0%\eta = 95.0\%

  1. Set up the efficiency relation:
    Given the target efficiency η=95.0%=0.950\eta = 95.0\% = 0.950 and cold reservoir temperature TC=295 KT_C = 295\text{ K}, substitute these values into the Carnot efficiency formula:

    0.950=1−295 KTH0.950 = 1 - \frac{295\text{ K}}{T_H}

  2. Rearrange to solve for THT_H:
    Isolate the ratio TCTH\frac{T_C}{T_H}:

    295 KTH=1−0.950=0.050\frac{295\text{ K}}{T_H} = 1 - 0.950 = 0.050

    Solve for THT_H:

    TH=295 K0.050=5900 KT_H = \frac{295\text{ K}}{0.050} = 5900\text{ K}

Thus, the hot reservoir must be maintained at a minimum temperature of TH=5900 KT_H = 5900\text{ K}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student inverts the temperature ratio in the Carnot efficiency formula, defining efficiency as 1 - TH/TC, which leads to an unphysical negative value for the required hot temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    η=1−THTC  ⟹  As TH→∞,  η→−∞\eta = 1 - \frac{T_H}{T_C} \implies \text{As } T_H \to \infty,\; \eta \to -\infty

    Correct

    η=1−TCTH  ⟹  lim⁡TH→∞η=1−0=1.00 (or 100%)\eta = 1 - \frac{T_C}{T_H} \implies \lim_{T_H \to \infty} \eta = 1 - 0 = 1.00\text{ (or } 100\%\text{)}

    Carnot efficiency is defined as η=1−QCQH=1−TCTH\eta = 1 - \frac{Q_C}{Q_H} = 1 - \frac{T_C}{T_H}. Because THT_H is in the denominator, taking TH→∞T_H \to \infty causes TCTH→0\frac{T_C}{T_H} \to 0, making the asymptotic efficiency approach 1.001.00 (100%100\%) rather than −∞-\infty.

  2. Step 2

    0.950=1−TH295  ⟹  TH295=0.0500.950 = 1 - \frac{T_H}{295} \implies \frac{T_H}{295} = 0.050

    Correct

    0.950=1−295TH  ⟹  295TH=0.0500.950 = 1 - \frac{295}{T_H} \implies \frac{295}{T_H} = 0.050

    You isolated the fraction correctly from your working equation, but this step carries forward the inverted ratio from Step 1.

  3. Step 3

    TH=−280.25 KT_H = -280.25\text{ K}

    Correct

    TH=295 K0.050=5900 KT_H = \frac{295\text{ K}}{0.050} = 5900\text{ K}

    Solving the correct relation 295 KTH=0.050\frac{295\text{ K}}{T_H} = 0.050 yields TH=5900 KT_H = 5900\text{ K}. Additionally, temperatures on the Kelvin scale cannot be negative, which is an immediate signal that an algebraic error occurred.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that efficiency connects the operating temperatures of the reservoir and sink.

You correctly isolated the subtracted term by subtracting the efficiency from 11.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Carnot ratio

You made an arithmetic slip in calculating the final numerical value of THT_H, arriving at a negative Kelvin temperature.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You reversed the numerator and denominator in the Carnot temperature ratio, using THTC\frac{T_H}{T_C} instead of TCTH\frac{T_C}{T_H}. Because efficiency measures work extracted relative to heat input, the discarded heat fraction is QCQH=TCTH\frac{Q_C}{Q_H} = \frac{T_C}{T_H}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Ratio Placement Check
  • Carnot efficiency is η=1−TCTH\eta = 1 - \frac{T_C}{T_H}, where TC<THT_C < T_H.

  • Always verify that TCTH<1\frac{T_C}{T_H} < 1, ensuring η\eta lies strictly between 00 and 11.

Physical Reality Check
  • Absolute temperature on the Kelvin scale must always be non-negative (T≥0 KT \ge 0\text{ K}).

  • If your calculated temperature turns out negative, stop and check your sign conventions and ratio orientations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the correct Carnot formula: η=1−TCTH\eta = 1 - \frac{T_C}{T_H}.

  2. Evaluate the limit for part (a): as TH→∞T_H \to \infty, TCTH→0\frac{T_C}{T_H} \to 0, so η→1.00\eta \to 1.00 (100%100\%).

  3. Set up part (b): 0.950=1−295 KTH0.950 = 1 - \frac{295\text{ K}}{T_H}.

  4. Isolate the temperature ratio: 295 KTH=1−0.950=0.050\frac{295\text{ K}}{T_H} = 1 - 0.950 = 0.050.

  5. Solve for the hot temperature: TH=295 K0.050=5900 KT_H = \frac{295\text{ K}}{0.050} = 5900\text{ K}.

Final answer

(a) lim⁡TH→∞η=1.00\lim_{T_H \to \infty} \eta = 1.00 (100%100\%); (b) TH=5900 KT_H = 5900\text{ K}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the efficiency definition from first principles: η=WQH=QH−QCQH=1−QCQH=1−TCTH\eta = \frac{W}{Q_H} = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H} = 1 - \frac{T_C}{T_H}.

  • Practice solving for both THT_H and TCT_C across different target efficiencies to build confidence in algebraic rearrangement.

  • Perform a sanity check on every thermal result: efficiency must satisfy 0≤η<10 \le \eta < 1, and TH>TC>0 KT_H > T_C > 0\text{ K}.

OverviewACEpath Teacher's Diagnosis

02 The student omits the term 1 minus the ratio and mistakenly defines Carnot efficiency directly as TC/TH, causing the limit to be 0 and the required temperature to be 310.5 K.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    η=TCTH  ⟹  As TH→∞, η→0\eta = \frac{T_C}{T_H} \implies \text{As } T_H \to \infty,\ \eta \to 0

    Correct

    η=1−TCTH  ⟹  lim⁡TH→∞η=1−0=1.00 (100%)\eta = 1 - \frac{T_C}{T_H} \implies \lim_{T_H \to \infty} \eta = 1 - 0 = 1.00\text{ }(100\%)

    You omitted the leading 1−…1 - \dots term in the Carnot efficiency formula. Thermal efficiency is defined by the work produced relative to heat absorbed, η=WQH=1−QCQH=1−TCTH\eta = \frac{W}{Q_H} = 1 - \frac{Q_C}{Q_H} = 1 - \frac{T_C}{T_H}. As TH→∞T_H \to \infty, the ratio TCTH→0\frac{T_C}{T_H} \to 0, making the asymptotic efficiency approach 11 (100%100\%), not 00.

  2. Step 2

    0.950=295TH  ⟹  TH=2950.950  ⟹  TH=310.5 K0.950 = \frac{295}{T_H} \implies T_H = \frac{295}{0.950} \implies T_H = 310.5\text{ K}

    Correct

    0.950=1−295 KTH  ⟹  295 KTH=0.050  ⟹  TH=5900 K0.950 = 1 - \frac{295\text{ K}}{T_H} \implies \frac{295\text{ K}}{T_H} = 0.050 \implies T_H = 5900\text{ K}

    You solved your equation for THT_H correctly, but the result was affected by using the ratio TCTH\frac{T_C}{T_H} directly instead of setting 1−TCTH=0.9501 - \frac{T_C}{T_H} = 0.950.

WHAT YOU DID WELL
Compliments from Your Teacher

You evaluated the limit of a rational term as the denominator approaches infinity correctly.

You correctly isolated the variable in the denominator during your algebraic rearrangement.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Carnot efficiency formula omission

You set efficiency directly equal to the rejected-heat ratio TCTH\frac{T_C}{T_H} rather than subtracting that ratio from 11.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the fraction of heat rejected to the cold reservoir, QCQH=TCTH\frac{Q_C}{Q_H} = \frac{T_C}{T_H}, with the fraction of heat converted into useful work, η=1−TCTH\eta = 1 - \frac{T_C}{T_H}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Recall the definition of efficiency
  • η=WQH=QH−QCQH=1−QCQH\eta = \frac{W}{Q_H} = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H}

  • Always subtract the lost energy fraction from 1 when calculating efficiency.

Sanity check the infinite-temperature limit
  • A hotter heat source provides higher thermodynamic efficiency.

  • Check whether your formula yields higher efficiency as THT_H increases; if efficiency drops toward 0 as THT_H gets hotter, the ratio is missing the 1−1 - term.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the Carnot efficiency formula: η=1−TCTH\eta = 1 - \frac{T_C}{T_H}.

  2. Evaluate the limit for part (a): as TH→∞T_H \to \infty, TCTH→0\frac{T_C}{T_H} \to 0, so lim⁡TH→∞η=1−0=1.00\lim_{T_H \to \infty} \eta = 1 - 0 = 1.00 (100%100\%).

  3. Set up part (b) with target efficiency: 0.950=1−295 KTH0.950 = 1 - \frac{295\text{ K}}{T_H}.

  4. Isolate the temperature ratio: 295 KTH=1−0.950=0.050\frac{295\text{ K}}{T_H} = 1 - 0.950 = 0.050.

  5. Solve for the reservoir temperature: TH=295 K0.050=5900 KT_H = \frac{295\text{ K}}{0.050} = 5900\text{ K}.

Final answer

(a) lim⁡TH→∞η=1.00\lim_{T_H \to \infty} \eta = 1.00 (100%100\%); (b) TH=5900 KT_H = 5900\text{ K}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the First and Second Laws derivation of heat engine efficiency: η=WQH=1−TCTH\eta = \frac{W}{Q_H} = 1 - \frac{T_C}{T_H}.

  • Use physical boundary checks: as TH→TCT_H \to T_C, η→0\eta \to 0; as TH→∞T_H \to \infty, η→1\eta \to 1.

OverviewACEpath Teacher's Diagnosis

03 The student treats the percentage 95.0% as 95 in the efficiency formula rather than converting it to the decimal 0.950, calculating an unphysical negative temperature of -3.14 K.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    η=1−TCTH  ⟹  As TH→∞, TCTH→0  ⟹  Limit of η=1 (100%)\eta = 1 - \frac{T_C}{T_H} \implies \text{As } T_H \to \infty,\, \frac{T_C}{T_H} \to 0 \implies \text{Limit of } \eta = 1\text{ (100\%)}

  2. Step 2

    η=1−TCTH  ⟹  95=1−295TH\eta = 1 - \frac{T_C}{T_H} \implies 95 = 1 - \frac{295}{T_H}

    Correct

    0.950=1−295 KTH0.950 = 1 - \frac{295\text{ K}}{T_H}

    In thermodynamic equations, efficiency η\eta is a dimensionless fraction between 00 and 11. Substituting 9595 instead of 0.9500.950 caused 1−η1 - \eta to become negative.

  3. Step 3

    295TH=−94  ⟹  TH=−3.14 K\frac{295}{T_H} = -94 \implies T_H = -3.14\text{ K}

    Correct

    295 KTH=0.050  ⟹  TH=5900 K\frac{295\text{ K}}{T_H} = 0.050 \implies T_H = 5900\text{ K}

    Your algebraic rearrangement followed correctly from your prior equation, but absolute temperature on the Kelvin scale cannot be negative for ideal thermal reservoirs.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated the Carnot efficiency relationship η=1−TCTH\eta = 1 - \frac{T_C}{T_H}.

You accurately evaluated the mathematical limit as TH→∞T_H \to \infty to find the maximum theoretical efficiency of 100%100\%.

You carried out the algebraic steps to isolate the variable THT_H correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Percentage-to-decimal conversion omission in efficiency formula

You substituted the percentage value 9595 directly into the formula instead of its decimal equivalent 0.9500.950.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating percentage notation (95%95\%) with the raw numerical value (0.9500.950) required by physical formulas where efficiency is defined as a dimensionless ratio of energies η=WQH≤1\eta = \frac{W}{Q_H} \le 1.

REASONING PATH
Your ACEpath teacher’s suggested approach
Efficiency Scale Verification
  • In formulas, efficiency η\eta must satisfy 0≤η≤10 \le \eta \le 1 (95.0%=0.95095.0\% = 0.950).

  • Always convert percentages to decimal fractions before substituting them into thermodynamic equations.

Kelvin Temperature Sanity Check
  • Absolute temperature on the Kelvin scale must satisfy T>0 KT > 0\text{ K}.

  • If a thermodynamic calculation yields T<0 KT < 0\text{ K}, pause immediately and check whether a factor of 100%100\% was misapplied.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the Carnot relation with the decimal efficiency: 0.950=1−295 KTH0.950 = 1 - \frac{295\text{ K}}{T_H}

  2. Isolate the temperature ratio: 295 KTH=1−0.950=0.050\frac{295\text{ K}}{T_H} = 1 - 0.950 = 0.050

  3. Invert to solve for the hot reservoir temperature: TH=295 K0.050=5900 KT_H = \frac{295\text{ K}}{0.050} = 5900\text{ K}

Final answer

(a) lim⁡TH→∞η=1.00 (100%)\lim_{T_H \to \infty} \eta = 1.00\text{ (100\%)}; (b) TH=5900 KT_H = 5900\text{ K}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how percentage quantities must be converted to dimensionless decimals in physical formulas before calculating.

  • Perform a quick physical sanity check on all thermodynamic variables: absolute temperatures must always be positive.

Lock it in

Similar question

01

A Carnot heat engine operates between a hot reservoir at TH=800 KT_H = 800\text{ K} and a cold sink at TC=200 KT_C = 200\text{ K}. Calculate its thermal efficiency η\eta as a percentage.

Answer

η=75%\eta = 75\%. Apply η=1−TCTH=1−200 K800 K=1−0.25=0.75=75%\eta = 1 - \frac{T_C}{T_H} = 1 - \frac{200\text{ K}}{800\text{ K}} = 1 - 0.25 = 0.75 = 75\%.

02

A geothermal Carnot engine exhausts heat to ambient air at TC=280 KT_C = 280\text{ K}. If the engine must achieve a minimum thermal efficiency of 60.0%60.0\%, what is the minimum required temperature THT_H of the geothermal source in Kelvin?

Answer

TH=700 KT_H = 700\text{ K}. Using η=1−TCTH\eta = 1 - \frac{T_C}{T_H}, rearrange to TCTH=1−η=1−0.600=0.400\frac{T_C}{T_H} = 1 - \eta = 1 - 0.600 = 0.400. Thus, TH=280 K0.400=700 KT_H = \frac{280\text{ K}}{0.400} = 700\text{ K}.

03

An engineer claims that by doubling the absolute temperature of the hot reservoir from THT_H to 2TH2T_H while keeping TCT_C fixed, the efficiency of a Carnot engine doubles. If the initial efficiency is η1=40.0%\eta_1 = 40.0\%, determine the actual new efficiency η2\eta_2 and state whether the engineer's claim is valid.

Answer

η2=70.0%\eta_2 = 70.0\%; the claim is invalid. From η1=1−TCTH=0.400\eta_1 = 1 - \frac{T_C}{T_H} = 0.400, we find TCTH=0.600\frac{T_C}{T_H} = 0.600. Doubling THT_H gives a new ratio TC2TH=0.6002=0.300\frac{T_C}{2T_H} = \frac{0.600}{2} = 0.300. The new efficiency is η2=1−0.300=0.700=70.0%\eta_2 = 1 - 0.300 = 0.700 = 70.0\%, which is not 2×40.0%=80.0%2 \times 40.0\% = 80.0\%.

Loading workspace…