Resources
A uniform traffic signal of mass is suspended in static equilibrium at an intersection by two lightweight cables. Cable 1 is anchored to a vertical pole and makes an angle of below the horizontal. Cable 2 is attached to a high horizontal mast arm and pulls upward and rightward at an angle above the horizontal. If the tension in Cable 1 is measured to be , determine the required elevation angle of Cable 2 and its tension to maintain complete translational equilibrium. Take .
Answer and steps
Final answer
,
Steps
Identify the Forces and Coordinate System
For the traffic signal to remain in complete static equilibrium, the vector sum of all external forces acting at the junction must equal zero:
Set up a standard Cartesian coordinate system where the positive -axis points horizontally to the right and the positive -axis points vertically upward.
The three forces acting at the junction are:
- Gravitational force (weight, ): Directed vertically downward along the negative -axis.
- Tension in Cable 1 (): Directed down and to the left at below the negative -axis, with magnitude .
- Tension in Cable 2 (): Directed up and to the right at angle above the positive -axis.
Resolve Forces into Components
Break each tension into horizontal and vertical components:
- Cable 1:
- Cable 2:
Common Pitfall: Cable 1 pulls downward as well as to the left. Students often mistakenly assume cables only pull upward when suspending an object, but Cable 1 actually adds to the total downward load that Cable 2 must support.
Apply Conditions of Static Equilibrium
Horizontal Equilibrium ():
Vertical Equilibrium ():
Solve for the Angle and Tension
Divide the vertical component equation by the horizontal component equation to eliminate :
Now, determine using the Pythagorean theorem on its orthogonal components:
Typical errors
01 The student assumes Cable 1 pulls upward instead of below the horizontal, subtracting rather than adding its vertical component to the weight.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You treated Cable 1 as pulling upward with . Since Cable 1 is angled below the horizontal, tension pulls away from the junction downward and to the left, so its vertical component must be negative ().
- Step 4Correct
Your mathematical steps for calculating , , and were logically sound, but the numerical values were thrown off by the sign error in the vertical component from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the gravitational force accurately.
You set up and evaluated the horizontal equilibrium equation correctly.
You used the correct trigonometric ratio to eliminate the unknown tension and solve for the angle.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisAssuming all supporting cables exert upward vertical components, overlooking the explicit problem specification that Cable 1 pulls below the horizontal.
REASONING PATH
Your ACEpath teacher’s suggested approach- Tension Direction Rule
Tension in a taut cable always pulls directly along the cable away from the object or joint of interest.
Sketch an arrow along the cable pointing outward from the junction; if the angle is below the horizontal, assign a negative sign to its vertical component.
- Physical Sanity Check on Supporting Cables
If a cable pulls downward, the upward cable must support both the object's weight and that downward pull.
Check whether before calculating angles.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the sum of vertical forces to zero with acting downward: .
Isolate the vertical component: .
Divide the vertical component by the horizontal component: .
Find the angle: .
Compute the tension: (or via ).
,
02 The student swaps the sine and cosine trigonometric functions when resolving the tension forces with respect to the horizontal.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You used instead of for the horizontal force components. Because both angles are measured from the horizontal, the adjacent horizontal component of each tension vector is given by .
- Step 3Correct
You used instead of for the vertical force components. Since vertical is opposite to the angle measured from the horizontal, vertical equilibrium requires .
- Step 4Correct
You followed the correct algebraic procedure to isolate , but your result was affected by the swapped trigonometric components from the previous steps.
- Step 5Correct
You correctly isolated from your previous equation, but the numerical answer inherits the earlier component error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the gravitational force acting on the traffic signal.
You correctly identified that Cable 1 pulls downward as well as horizontally.
You correctly used the tangent ratio and inverse tangent to solve for the unknown angle from component equations.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou swapped sine and cosine when projecting force vectors. When an angle is defined adjacent to the horizontal axis, the horizontal component is and the vertical component is .
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Adjacent vs. Opposite Legs
With respect to an angle adjacent to the horizontal, and .
Always draw a right triangle for each force vector and confirm which leg lies along the -axis before writing equilibrium equations.
- Check Relative Magnitudes
For , the horizontal leg must be larger than the vertical leg: .
Check that your horizontal component () is greater than your vertical component () when the angle to the horizontal is less than .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the horizontal balance equation using the adjacent cosine projection: .
Write the vertical balance equation using the opposite sine projection: .
Divide the vertical equation by the horizontal equation: .
Compute the tension magnitude: .
,
03 The student forgets to include the downward vertical component of Cable 1 in the vertical equilibrium equation, balancing the weight with Cable 2 alone.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because Cable 1 angles downward at below the horizontal, it exerts a downward vertical force in addition to the signal's weight . Cable 2 must support both.
- Step 4Correct
Your algebra to find the elevation angle was sound, but the value is affected by the missing force component in Step 3.
- Step 5Correct
Your method of solving for was mathematically consistent with your prior lines, but carries forward the error from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the weight of the traffic light from its mass and the acceleration due to gravity.
You correctly resolved and balanced the horizontal components of tension.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated Cable 2 as the sole vertical support balancing weight, overlooking that Cable 1 also pulls downward.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisAssuming suspended cables only pull upward or purely horizontally, rather than resolving the full 2D vector for a cable angled below the horizontal.
REASONING PATH
Your ACEpath teacher’s suggested approach- Free-Body Diagram Check
Every tension force acts strictly along the cable away from the junction. If a cable angles downward, its vertical component acts downward.
Draw arrows along each cable from the junction, and mark whether each component points along or before writing .
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the downward component of Cable 1:
Solve for the vertical component of Cable 2:
Find :
Calculate :
,
Lock it in
Which direction does the tension force exerted by a taut cable always point relative to the connected junction or object?
It always pulls away from the junction or object, along the line of the cable.
Similar question
A small junction ring is in static equilibrium under three forces: a downward weight , a cable pulling at an angle of below the negative -axis with tension , and a second cable pulling upward and to the right at an angle with tension . Determine the required vertical component and horizontal component of the second cable.
Answer
, . Key steps: Horizontal equilibrium gives . Because Cable 1 pulls below the horizontal, its vertical component is downward: . Vertical equilibrium requires .
A street lamp is held in static equilibrium by two cables connected at a single knot. Cable A is anchored to a wall and pulls downward and to the left at an angle of below the horizontal with a tension of . Cable B pulls upward and to the right at an angle above the horizontal with tension . Find the angle and tension . (Use .)
Answer
, . Key steps: Weight . Horizontal: . Vertical: Cable A pulls downward with , so . Then . Magnitude .
A mass hangs from a central ring. Cable 1 pulls at an angle below the horizontal to the left with tension . Cable 2 pulls at an angle above the horizontal to the right with tension . Determine and for static equilibrium. (Use .)
Answer
, (). Key steps: Weight . Horizontal equilibrium: . Vertical equilibrium: . Substitute : . Then .