Resources

An introductory physics student connects an incandescent tungsten filament lamp across an adjustable DC power supply. At a very low applied voltage of V1=1.50 VV_1 = 1.50\text{ V}, the measured current is I1=0.150 AI_1 = 0.150\text{ A}. The student then turns the dial to V2=120 VV_2 = 120\text{ V} and expects the current to scale linearly by a factor of 8080 to 12.0 A12.0\text{ A} based on Ohm's law. However, an ammeter measures the actual current to be only I2=1.20 AI_2 = 1.20\text{ A}. (a) Calculate the apparent resistance of the lamp filament at 1.50 V1.50\text{ V} (R1R_1) and at 120 V120\text{ V} (R2R_2). (b) Resolve the conceptual paradox: explain why the resistance changed, distinguishing between a component having electrical resistance versus a component being purely ohmic.

Answer and steps

Final answer

(a) R1=1.50 V0.150 A=10.0 ΩR_1 = \frac{1.50\text{ V}}{0.150\text{ A}} = 10.0\ \Omega; R2=120 V1.20 A=100 ΩR_2 = \frac{120\text{ V}}{1.20\text{ A}} = 100\ \Omega; (b) Ohm's law states that RR is constant and independent of VV and II only for ideal ohmic conductors; the tungsten filament is non-ohmic because significant Joule heating at 120 V120\text{ V} raises the filament's temperature, increasing lattice vibrations and electron scattering, which dramatically increases its intrinsic resistance tenfold from 10.0 Ω10.0\ \Omega to 100 Ω100\ \Omega.

Steps

01

Defining Resistance vs. Being "Ohmic"

Part (a): Calculating the Filament Resistance at Both Voltages

At any operating state, the operational resistance RR of a circuit component is defined by the ratio of the potential difference across it (VV) to the electric current flowing through it (II): R=VIR = \frac{V}{I}

  1. At the lower voltage (V1=1.50 VV_1 = 1.50\text{ V}): R1=V1I1=1.50 V0.150 A=10.0 ΩR_1 = \frac{V_1}{I_1} = \frac{1.50\text{ V}}{0.150\text{ A}} = 10.0\ \Omega
  2. At the higher voltage (V2=120 VV_2 = 120\text{ V}): R2=V2I2=120 V1.20 A=100 ΩR_2 = \frac{V_2}{I_2} = \frac{120\text{ V}}{1.20\text{ A}} = 100\ \Omega

Part (b): Resolving the Paradox (Ohmic vs. Non-Ohmic Behavior)

  • Resistance (RR): Any material or component that impedes the flow of charge has an electrical resistance, simply calculated at any instant by R=VIR = \frac{V}{I}. Both ohmic and non-ohmic devices have resistance.
  • Ohmic Conductor: An object is strictly ohmic only if its resistance remains constant regardless of the applied voltage or current across its operating range (V∝IV \propto I). For an ohmic resistor, the current-voltage graph (II-VV characteristic) is a straight line through the origin.
02

Why the Tungsten Filament Is Non-Ohmic

  • Joule Heating: The electrical power dissipated in the filament is given by:

    P=V⋅IP = V \cdot I

    At 1.50 V1.50\text{ V}, the dissipated power is tiny:

    P1=1.50 V⋅0.150 A=0.225 WP_1 = 1.50\text{ V} \cdot 0.150\text{ A} = 0.225\text{ W}

    At this power level, the filament remains near room temperature.

    At 120 V120\text{ V}, the power increases dramatically:

    P2=120 V⋅1.20 A=144 WP_2 = 120\text{ V} \cdot 1.20\text{ A} = 144\text{ W}

    This massive dissipation heats the tungsten wire to well over 2000∘C2000^\circ\text{C}, causing it to glow white-hot.

  • Microscopic Cause of Increased Resistance: In metals like tungsten, electrical resistance arises from conduction electrons colliding with vibrating metal ions in the crystal lattice. As temperature rises, the thermal vibrations of the lattice ions increase in amplitude, presenting a larger effective collision cross-section to drifting electrons. These frequent collisions increase the resistivity ρ\rho of the material according to:

    R(T)≈R0[1+α(T−T0)]R(T) \approx R_0 [1 + \alpha(T - T_0)]

    where α>0\alpha > 0 is the temperature coefficient of resistivity for tungsten.

Because the filament's temperature changes significantly with operating conditions, its resistance increases tenfold (from 10.0 Ω10.0\ \Omega to 100 Ω100\ \Omega), meaning the current only increases by a factor of 88 instead of the expected factor of 8080. The filament is therefore a non-ohmic device.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the definition of resistance with conductance by using R = I / V instead of R = V / I.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    R1=I1V1=0.150 A1.50 V=0.100 ΩR_1 = \frac{I_1}{V_1} = \frac{0.150\text{ A}}{1.50\text{ V}} = 0.100\ \Omega

    Correct

    R1=V1I1=1.50 V0.150 A=10.0 ΩR_1 = \frac{V_1}{I_1} = \frac{1.50\text{ V}}{0.150\text{ A}} = 10.0\ \Omega

    You inverted the definition of electrical resistance. Resistance is defined as potential difference divided by current (R=VIR = \frac{V}{I}), whereas IV\frac{I}{V} defines electrical conductance (GG).

  2. Step 2

    R2=I2V2=1.20 A120 V=0.0100 ΩR_2 = \frac{I_2}{V_2} = \frac{1.20\text{ A}}{120\text{ V}} = 0.0100\ \Omega

    Correct

    R2=V2I2=120 V1.20 A=100 ΩR_2 = \frac{V_2}{I_2} = \frac{120\text{ V}}{1.20\text{ A}} = 100\ \Omega

    You correctly carried out your chosen formula with the provided values, but because the formula was inverted from Step 1, the result represents conductance rather than resistance.

  3. Step 3

    Current heats up the wire, causing resistance to drop from 0.100 Ω to 0.0100 Ω.\text{Current heats up the wire, causing resistance to drop from } 0.100\ \Omega \text{ to } 0.0100\ \Omega.

    Correct

    Joule heating from the higher electrical power dissipation increases the temperature of the tungsten filament. Higher temperature increases lattice vibrations and electron scattering, causing the resistance to increase tenfold from 10.0 Ω10.0\ \Omega to 100 Ω100\ \Omega.

    Because of the inverted formula, you concluded that the resistance decreased. In reality, for metallic conductors like tungsten, increased temperature causes greater lattice ion vibration, leading to more frequent electron collisions and an increase in resistance.

  4. Step 4

    A component has resistance when R=IV is non-zero, but is ohmic only if R stays constant as voltage changes.\text{A component has resistance when } R = \frac{I}{V} \text{ is non-zero, but is ohmic only if } R \text{ stays constant as voltage changes.}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that being ohmic requires resistance to remain constant as the applied voltage changes.

You correctly set up ratios using the corresponding current and voltage pairs at both operating points.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Definition of Resistance ($R = \frac{I}{V}$ instead of $R = \frac{V}{I}$)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused resistance (RR) with electrical conductance (G=1R=IVG = \frac{1}{R} = \frac{I}{V}). Consequently, the calculated values were conductances rather than resistances, which led you to conclude that resistance drops upon heating instead of rising.

REASONING PATH
Your ACEpath teacher’s suggested approach
Operational Definition of Resistance
  • Electrical resistance measures the voltage required per unit of current: R=VIR = \frac{V}{I} (measured in ohms, Ω=V/A\Omega = \text{V}/\text{A}).

  • Always double-check your units: ohms are volts divided by amperes (V/A\text{V}/\text{A}). If you calculate amperes per volt (A/V\text{A}/\text{V}), you have calculated conductance in siemens (S\text{S}).

Temperature Dependence of Metals
  • For metallic conductors, resistivity and resistance increase as temperature rises due to increased electron-lattice scattering.

  • Check whether your numerical trend aligns with physical reality: when a metal filament heats up, its resistance must increase, not decrease.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the operational definition of resistance: R=VIR = \frac{V}{I}.

  2. At 1.50 V1.50\text{ V}: R1=1.50 V0.150 A=10.0 ΩR_1 = \frac{1.50\text{ V}}{0.150\text{ A}} = 10.0\ \Omega.

  3. At 120 V120\text{ V}: R2=120 V1.20 A=100 ΩR_2 = \frac{120\text{ V}}{1.20\text{ A}} = 100\ \Omega.

  4. Explain the resistance increase: the filament dissipates electrical power (P=VIP = VI), heating the tungsten wire white-hot. Increased thermal vibration of the metal lattice increases electron scattering, driving the resistance up by a factor of 1010.

Final answer

(a) R1=10.0 ΩR_1 = 10.0\ \Omega, R2=100 ΩR_2 = 100\ \Omega; (b) Resistance increases from 10.0 Ω10.0\ \Omega to 100 Ω100\ \Omega because thermal heating increases electron-phonon collisions in the tungsten lattice; the lamp is non-ohmic because RR is not constant.

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize V=IRV = IR as the primary relationship so you can easily rearrange it to R=VIR = \frac{V}{I}.

  • Remember that standard metals always show a positive temperature coefficient of resistance (α>0\alpha > 0), meaning hot metals have higher resistance than cold metals.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the non-ohmic behavior as an experimental measurement error, believing real materials must strictly follow linear Ohm's law with constant resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R1=V1I1=1.50 V0.150 A=10.0 Ω  ⟹  R2=V2I2=120 V1.20 A=100 ΩR_1 = \frac{V_1}{I_1} = \frac{1.50\text{ V}}{0.150\text{ A}} = 10.0\ \Omega \implies R_2 = \frac{V_2}{I_2} = \frac{120\text{ V}}{1.20\text{ A}} = 100\ \Omega

  2. Step 2

    Tungsten is a metal so it must be an ohmic material with a constant resistance of 10.0 Ω10.0\ \Omega. The resistance measured at 120 V120\text{ V} changed to 100 Ω100\ \Omega because internal ammeter resistance or measurement error introduced a discrepancy from the true constant resistance.

    Correct

    Ohm's law requires resistance to remain constant across varying voltages, which only holds under constant physical conditions like temperature. At 120 V120\text{ V}, substantial electrical power (P=VI=144 WP = VI = 144\text{ W}) heats the filament significantly, increasing thermal lattice vibrations and electron scattering, which raises its intrinsic resistance tenfold to 100 Ω100\ \Omega, demonstrating non-ohmic behavior.

    You treated metallic conduction as strictly ohmic under all operating conditions and dismissed the real physical change in resistance as measurement error. The resistance change is an intrinsic physical effect: massive Joule heating at high voltage raises the metal's temperature and therefore its resistivity.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the apparent resistance at both low and high voltages using the operational definition R=VIR = \frac{V}{I}.

You recognized that the calculated resistance values differed between the two voltage states.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing Ohmic Behavior with General Resistance

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that all metals are inherently ohmic under all operating conditions, overlooking that Ohm's law (R=constantR = \text{constant}) requires constant temperature, and that significant Joule heating causes metals to exhibit non-ohmic, temperature-dependent resistance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Resistance vs. Ohm's Law
  • Any component has instantaneous resistance defined by R=VIR = \frac{V}{I}, but it is only 'ohmic' if RR remains constant as VV and II vary.

  • Check whether physical conditions—especially temperature—change significantly across the operating range.

Temperature Dependence of Metallic Resistance
  • For metals, electrical resistance increases with temperature (R(T)≈R0[1+αΔT]R(T) \approx R_0[1 + \alpha\Delta T]) because higher temperatures increase thermal lattice vibrations and electron collision rates.

  • Evaluate the dissipated power (P=VIP = VI) to see if Joule heating alters the operating temperature.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the electrical power dissipated at each operating voltage: P1=(1.50 V)(0.150 A)=0.225 WP_1 = (1.50\text{ V})(0.150\text{ A}) = 0.225\text{ W} versus P2=(120 V)(1.20 A)=144 WP_2 = (120\text{ V})(1.20\text{ A}) = 144\text{ W}.

  2. Note that at 144 W144\text{ W}, the tungsten filament heats to well over 2000∘C2000^\circ\text{C}, whereas at 0.225 W0.225\text{ W} it remains near room temperature.

  3. Relate temperature to resistance: enhanced lattice vibrations at high temperatures cause more frequent collisions with conduction electrons, dramatically increasing resistivity (R∝TR \propto T).

  4. Conclude that because RR changes with applied voltage and current, the incandescent lamp is non-ohmic, and the measured 100 Ω100\ \Omega is a genuine physical property rather than an experimental error.

Final answer

(a) R1=10.0 ΩR_1 = 10.0\ \Omega, R2=100 ΩR_2 = 100\ \Omega; (b) The lamp is non-ohmic because large Joule heating at 120 V120\text{ V} (144 W144\text{ W}) raises the filament's temperature, increasing lattice scattering and raising the intrinsic resistance from 10.0 Ω10.0\ \Omega to 100 Ω100\ \Omega.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between the operational definition of resistance (R=V/IR = V/I) and Ohm's empirical law (V∝IV \propto I with constant RR).

  • Practice sketching and interpreting non-linear I–VI\text{--}V characteristic curves for filament lamps and diodes.

OverviewACEpath Teacher's Diagnosis

03 The student attributes the resistance increase to a thermal expansion in the physical dimensions of the wire rather than an increase in temperature-dependent resistivity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R1=V1I1=1.50 V0.150 A=10.0 ΩR_1 = \frac{V_1}{I_1} = \frac{1.50\text{ V}}{0.150\text{ A}} = 10.0\ \Omega ⟹ R2=V2I2=120 V1.20 A=100 ΩR_2 = \frac{V_2}{I_2} = \frac{120\text{ V}}{1.20\text{ A}} = 100\ \Omega

  2. Step 2

    The higher voltage heats the filament, causing thermal expansion that significantly lengthens the wire to increase R=ρL/AR = \rho L/A tenfold.

    Correct

    Joule heating from increased power dissipation raises the filament temperature significantly, which increases thermal lattice vibrations and electron collisions, driving a large increase in resistivity ρ(T)\rho(T) rather than wire dimensions.

    Thermal expansion increases the length of a tungsten filament by only around 1%1\%, which cannot account for a 1000%1000\% (10×10\times) change in resistance. The increase is almost entirely driven by the temperature dependence of intrinsic resistivity ρ\rho due to intensified electron-phonon scattering.

  3. Step 3

    A component has resistance if R=VI>0R = \frac{V}{I} > 0, but is ohmic only if its dimensions and resistance remain constant.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the operating resistances R1=10.0 ΩR_1 = 10.0\ \Omega and R2=100 ΩR_2 = 100\ \Omega using Ohm's ratio.

You clearly recognized that an ohmic component requires a constant resistance across operating states.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misconception: Geometric vs. Resistivity Origins of Temperature-Dependent Resistance

No computational slips were present in your numerical calculations.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You mistakenly assumed that temperature affects macroscopic resistance predominantly through geometric changes (thermal expansion changing length and area) rather than microscopic transport properties (thermal lattice vibrations drastically increasing resistivity ρ\rho).

REASONING PATH
Your ACEpath teacher’s suggested approach
Geometric vs. Intrinsic Changes
  • Thermal expansion alters wire dimensions by only ≈1%\approx 1\%, whereas intrinsic resistivity ρ(T)\rho(T) can change by an order of magnitude or more over thousands of kelvins.

  • Attribute large thermal resistance changes in conductors to temperature-dependent resistivity ρ(T)\rho(T) caused by lattice scattering, not changes in LL or AA.

Defining Ohmic Behavior
  • A device is ohmic if and only if V∝IV \propto I (R=constantR = \text{constant} across the working range).

  • Check whether resistance remains constant as operating voltage changes; if RR varies, the device is non-ohmic regardless of whether R=V/IR = V/I is defined at each point.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the change in operating temperature and recognize that tungsten's linear thermal expansion coefficient is tiny: αL≈4.5×10−6 K−1\alpha_L \approx 4.5 \times 10^{-6}\text{ K}^{-1}.

  2. Even a 2000 K2000\text{ K} rise produces ΔLL≈1%\frac{\Delta L}{L} \approx 1\%, while ΔAA≈2%\frac{\Delta A}{A} \approx 2\%, which slightly decreases geometric L/AL/A.

  3. Attribute the tenfold increase in R=ρLAR = \frac{\rho L}{A} entirely to the temperature dependence of resistivity: ρ(T)=ρ0[1+αR(T−T0)]\rho(T) = \rho_0 [1 + \alpha_R(T - T_0)], where lattice ion vibrations scatter conduction electrons far more frequently.

Final answer

(a) R1=10.0 ΩR_1 = 10.0\ \Omega, R2=100 ΩR_2 = 100\ \Omega; (b) The filament has electrical resistance at every point (R=V/IR = V/I), but is non-ohmic because Joule heating raises its temperature above 2000∘C2000^\circ\text{C}, vastly increasing lattice vibrations and electron scattering (resistivity ρ\rho), which causes resistance to increase tenfold.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the microscopic model of conduction (Drude model) to see why collision frequency increases with lattice temperature.

  • Compare typical values of linear expansion coefficients (≈10−5 K−1\approx 10^{-5}\text{ K}^{-1}) with temperature coefficients of resistivity (≈10−3 K−1\approx 10^{-3}\text{ K}^{-1}).

Lock it in

Similar question

01

A copper wire has a potential difference of 0.80 V0.80\text{ V} across its ends while carrying a current of 4.0 A4.0\text{ A}. Calculate the resistance of the wire.

Answer

R=VI=0.80 V4.0 A=0.20 ΩR = \frac{V}{I} = \frac{0.80\text{ V}}{4.0\text{ A}} = 0.20\ \Omega.

02

A non-ohmic device has a current-voltage relationship given by I=0.050 V2I = 0.050\,V^2, where VV is in volts and II is in amperes. Determine the apparent resistance of the device at V=2.0 VV = 2.0\text{ V} and at V=10 VV = 10\text{ V}. Does its resistance increase or decrease with voltage?

Answer

At V=2.0 VV = 2.0\text{ V}: I=0.050(2.0)2=0.20 AI = 0.050(2.0)^2 = 0.20\text{ A}, so R1=2.0 V0.20 A=10 ΩR_1 = \frac{2.0\text{ V}}{0.20\text{ A}} = 10\ \Omega.\nAt V=10 VV = 10\text{ V}: I=0.050(10)2=5.0 AI = 0.050(10)^2 = 5.0\text{ A}, so R2=10 V5.0 A=2.0 ΩR_2 = \frac{10\text{ V}}{5.0\text{ A}} = 2.0\ \Omega.\nThe resistance decreases as the voltage increases.

03

At room temperature (20∘C20^\circ\text{C}), a platinum sensor has a resistance of 100 Ω100\ \Omega and draws 0.020 A0.020\text{ A}. When immersed in a furnace at 500∘C500^\circ\text{C}, the applied voltage is increased to 5.40 V5.40\text{ V} and the measured current is 0.020 A0.020\text{ A}. (a) Calculate the furnace resistance R2R_2. (b) Explain on a microscopic level why the resistance changed in this direction.

Answer

(a) R2=V2I2=5.40 V0.020 A=270 ΩR_2 = \frac{V_2}{I_2} = \frac{5.40\text{ V}}{0.020\text{ A}} = 270\ \Omega.\n(b) At higher temperatures, platinum lattice ions vibrate with larger thermal amplitudes, presenting a larger scattering cross-section to conduction electrons. The increased frequency of electron-ion collisions impedes drift velocity, increasing resistivity and raising the resistance from 100 Ω100\ \Omega to 270 Ω270\ \Omega.

Loading workspace…