Resources

An engineer designs an experimental reversible Carnot heat pump intended to maintain a building interior at a steady temperature of TH=295 KT_H = 295\text{ K}. Analysis of the heating data demonstrates that the heat pump supplies heat to the interior at a rate of Q˙H=8.50 kW\dot{Q}_H = 8.50\text{ kW} while consuming electrical mechanical power at W˙in=1.25 kW\dot{W}_{\text{in}} = 1.25\text{ kW}. Assuming the unit operates at the theoretical maximum reversible thermodynamic limit, determine: (a) the coefficient of performance for heating COPHP\text{COP}_{\text{HP}}, (b) the outdoor ambient temperature TCT_C in kelvins, and (c) the outdoor temperature in degrees Celsius.

Answer and steps

Final answer

(a) COPHP=6.80\text{COP}_{\text{HP}} = 6.80; (b) TC=252 KT_C = 252\text{ K}; (c) TC=−21.6∘CT_C = -21.6^\circ\text{C}.

Steps

Part (a): Coefficient of Performance (COPHP\text{COP}_{\text{HP}})

The coefficient of performance of a heat pump (COPHP\text{COP}_{\text{HP}}) measures the heating effectiveness and is defined as the ratio of the desired heat transfer rate delivered to the warm space (Q˙H\dot{Q}_H) to the required power input (W˙in\dot{W}_{\text{in}}):

COPHP=Q˙HW˙in\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}}

Substitute the given values:

COPHP=8.50 kW1.25 kW=6.80\text{COP}_{\text{HP}} = \frac{8.50\text{ kW}}{1.25\text{ kW}} = 6.80


Part (b): Outdoor Ambient Temperature (TCT_C) in Kelvins

For a fully reversible (Carnot) heat pump, the coefficient of performance is limited solely by the absolute temperatures of the high-temperature reservoir (THT_H) and low-temperature reservoir (TCT_C):

COPHP, rev=THTH−TC\text{COP}_{\text{HP, rev}} = \frac{T_H}{T_H - T_C}

Rearrange the equation to isolate the temperature difference (TH−TC)(T_H - T_C):

TH−TC=THCOPHPT_H - T_C = \frac{T_H}{\text{COP}_{\text{HP}}}

TC=TH−THCOPHP=TH(1−1COPHP)T_C = T_H - \frac{T_H}{\text{COP}_{\text{HP}}} = T_H \left(1 - \frac{1}{\text{COP}_{\text{HP}}}\right)

Substitute TH=295 KT_H = 295\text{ K} and COPHP=6.80\text{COP}_{\text{HP}} = 6.80:

TC=295 K⋅(1−16.80)≈295 K⋅0.85294≈251.62 KT_C = 295\text{ K} \cdot \left(1 - \frac{1}{6.80}\right) \approx 295\text{ K} \cdot 0.85294 \approx 251.62\text{ K}

Rounding to three significant figures gives:

TC≈252 KT_C \approx 252\text{ K}

Common Pitfall: Thermodynamic formulas for Carnot cycles require absolute temperature in kelvins (K\text{K}). Substituting temperatures in degrees Celsius directly into the Carnot efficiency or COP formulas leads to incorrect results.


Part (c): Outdoor Ambient Temperature in Degrees Celsius

Convert the unrounded Kelvin temperature to the Celsius scale using the standard relation T(∘C)=T(K)−273.15T(^\circ\text{C}) = T(\text{K}) - 273.15:

TC=251.6 K−273.2≈−21.6∘CT_C = 251.6\text{ K} - 273.2 \approx -21.6^\circ\text{C}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the coefficient of performance of a heat pump with that of a refrigerator, using heat absorbed from the cold reservoir rather than heat rejected to the warm interior.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Q˙C=Q˙H−W˙in=8.50 kW−1.25 kW=7.25 kW  ⟹  COP=Q˙CW˙in=7.25 kW1.25 kW=5.80\dot{Q}_C = \dot{Q}_H - \dot{W}_{\text{in}} = 8.50\text{ kW} - 1.25\text{ kW} = 7.25\text{ kW} \implies \text{COP} = \frac{\dot{Q}_C}{\dot{W}_{\text{in}}} = \frac{7.25\text{ kW}}{1.25\text{ kW}} = 5.80

    Correct

    COPHP=Q˙HW˙in=8.50 kW1.25 kW=6.80\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}} = \frac{8.50\text{ kW}}{1.25\text{ kW}} = 6.80

    You evaluated the coefficient of performance for cooling (a refrigerator, COPR=Q˙CW˙in\text{COP}_{\text{R}} = \frac{\dot{Q}_C}{\dot{W}_{\text{in}}}) instead of heating. For a heat pump, the desired output is the heat delivered to the warm interior, Q˙H\dot{Q}_H, giving COPHP=Q˙HW˙in\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}}.

  2. Step 2

    COP=TCTH−TC  ⟹  5.80=TC295 K−TC  ⟹  5.80(295−TC)=TC  ⟹  1711−5.80TC=TC  ⟹  6.80TC=1711  ⟹  TC=251.62 K\text{COP} = \frac{T_C}{T_H - T_C} \implies 5.80 = \frac{T_C}{295\text{ K} - T_C} \implies 5.80(295 - T_C) = T_C \implies 1711 - 5.80 T_C = T_C \implies 6.80 T_C = 1711 \implies T_C = 251.62\text{ K}

  3. Step 3

    TC(∘C)=251.62−273.15=−21.53∘CT_C(^\circ\text{C}) = 251.62 - 273.15 = -21.53^\circ\text{C}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the first law of thermodynamics to find the heat extracted from the cold source.

You correctly related the Carnot temperatures to your COP formulation and solved the algebraic equation without error.

You correctly converted the absolute temperature in kelvins to degrees Celsius.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing Heat Pump and Refrigerator COP

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You defined COP using the cooling benefit Q˙C\dot{Q}_C instead of the heating benefit Q˙H\dot{Q}_H. A heat pump is operated to heat a warm space, so its useful output is Q˙H\dot{Q}_H, which makes COPHP=Q˙HW˙in=COPR+1\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}} = \text{COP}_{\text{R}} + 1.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Desired Effect
  • COP=Desired OutputRequired Work Input\text{COP} = \frac{\text{Desired Output}}{\text{Required Work Input}}

  • Use Q˙H\dot{Q}_H in the numerator when the objective is heating, and Q˙C\dot{Q}_C when the objective is cooling.

Carnot Relation Between COPs
  • COPHP=COPR+1\text{COP}_{\text{HP}} = \text{COP}_{\text{R}} + 1

  • Check your heat pump COP: because Q˙H=Q˙C+W˙in\dot{Q}_H = \dot{Q}_C + \dot{W}_{\text{in}}, the heat pump COP must always exceed 11 by exactly the refrigerator COP value.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the desired thermal output for heating: Q˙H=8.50 kW\dot{Q}_H = 8.50\text{ kW}.

  2. Compute the heating coefficient of performance: COPHP=Q˙HW˙in=8.50 kW1.25 kW=6.80\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}} = \frac{8.50\text{ kW}}{1.25\text{ kW}} = 6.80.

Final answer

(a) COPHP=6.80\text{COP}_{\text{HP}} = 6.80; (b) TC=252 KT_C = 252\text{ K}; (c) TC=−21.6∘CT_C = -21.6^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the general definition COP=∣Qdesired∣∣Win∣\text{COP} = \frac{|Q_{\text{desired}}|}{|W_{\text{in}}|} before substituting numbers to verify whether you need QHQ_H or QCQ_C.

  • Verify that any heat pump COP satisfies COPHP>1\text{COP}_{\text{HP}} > 1, and specifically COPHP=COPR+1\text{COP}_{\text{HP}} = \text{COP}_{\text{R}} + 1 for the same operating reservoirs.

OverviewACEpath Teacher's Diagnosis

02 The student misremembers the Carnot heat pump COP formula as the Carnot heat engine thermal efficiency formula, COP = (T_H - T_C) / T_H.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    COPHP=Q˙HW˙in=8.501.25=6.80\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}} = \frac{8.50}{1.25} = 6.80

  2. Step 2

    COPHP=TH−TCTH  ⟹  6.80=295−TC295\text{COP}_{\text{HP}} = \frac{T_H - T_C}{T_H} \implies 6.80 = \frac{295 - T_C}{295}

    Correct

    COPHP, rev=THTH−TC  ⟹  6.80=295295−TC\text{COP}_{\text{HP, rev}} = \frac{T_H}{T_H - T_C} \implies 6.80 = \frac{295}{295 - T_C}

    You substituted the expression TH−TCTH\frac{T_H - T_C}{T_H}, which is the thermal efficiency of a Carnot heat engine (η=WQH<1\eta = \frac{W}{Q_H} < 1). For a reversible Carnot heat pump, the coefficient of performance is the reciprocal of engine efficiency, COPHP, rev=THTH−TC\text{COP}_{\text{HP, rev}} = \frac{T_H}{T_H - T_C}.

  3. Step 3

    295⋅6.80=295−TC  ⟹  2006=295−TC  ⟹  TC=295−2006=−1711 K295 \cdot 6.80 = 295 - T_C \implies 2006 = 295 - T_C \implies T_C = 295 - 2006 = -1711\text{ K}

    Correct

    TH−TC=295 K6.80≈43.38 K  ⟹  TC=295 K−43.38 K≈252 KT_H - T_C = \frac{295\text{ K}}{6.80} \approx 43.38\text{ K} \implies T_C = 295\text{ K} - 43.38\text{ K} \approx 252\text{ K}

    Your algebraic solving steps were executed consistently with your formula, but the result was propagated from the inverted COP formula. An absolute temperature below 0 K0\text{ K} is a strong clue that the relation was inverted.

  4. Step 4

    TC(∘C)=−1711−273.15=−1984.15∘CT_C(^{\circ}\text{C}) = -1711 - 273.15 = -1984.15^{\circ}\text{C}

    Correct

    TC(∘C)=251.62 K−273.15≈−21.6∘CT_C(^{\circ}\text{C}) = 251.62\text{ K} - 273.15 \approx -21.6^{\circ}\text{C}

    You correctly subtracted 273.15273.15 to convert kelvins to degrees Celsius, but the numerical value was skewed by the earlier formula error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the heat pump coefficient of performance from the given heat output and work input.

You correctly recognized that converting from kelvins to degrees Celsius requires subtracting 273.15273.15.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Carnot COP Formula

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the Carnot heat pump coefficient of performance COPHP=THTH−TC\text{COP}_{\text{HP}} = \frac{T_H}{T_H - T_C} with the Carnot heat engine thermal efficiency ηth=TH−TCTH\eta_{\text{th}} = \frac{T_H - T_C}{T_H}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Benefit vs. Cost Definition
  • Every efficiency metric equals Desired OutputRequired Input\frac{\text{Desired Output}}{\text{Required Input}}. For a heat pump, the desired output is QHQ_H delivered to the warm space, so COPHP=QHW=THTH−TC\text{COP}_{\text{HP}} = \frac{Q_H}{W} = \frac{T_H}{T_H - T_C}.

  • Always write the energy ratio QHW\frac{Q_H}{W} first, then replace heat terms with reversible temperatures.

Sanity Check on Values
  • A heat pump's coefficient of performance is always greater than 11 (since QH=QC+W>WQ_H = Q_C + W > W), whereas engine efficiency is always strictly less than 11.

  • If you see a formula where TH−TCTH\frac{T_H - T_C}{T_H} is equated to a value >1> 1, flip it to THTH−TC\frac{T_H}{T_H - T_C}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the reversible heat pump relation: COPHP, rev=THTH−TC\text{COP}_{\text{HP, rev}} = \frac{T_H}{T_H - T_C}.

  2. Substitute TH=295 KT_H = 295\text{ K} and COPHP=6.80\text{COP}_{\text{HP}} = 6.80: 6.80=295295−TC6.80 = \frac{295}{295 - T_C}.

  3. Solve for the temperature difference: 295−TC=2956.80≈43.38 K295 - T_C = \frac{295}{6.80} \approx 43.38\text{ K}.

  4. Compute TCT_C in kelvins: TC=295−43.38≈252 KT_C = 295 - 43.38 \approx 252\text{ K} (or 251.62 K251.62\text{ K}).

  5. Convert to degrees Celsius: TC(∘C)=251.62−273.15=−21.53∘C≈−21.6∘CT_C(^{\circ}\text{C}) = 251.62 - 273.15 = -21.53^{\circ}\text{C} \approx -21.6^{\circ}\text{C}.

Final answer

(a) COPHP=6.80\text{COP}_{\text{HP}} = 6.80; (b) TC=252 KT_C = 252\text{ K}; (c) TC=−21.6∘CT_C = -21.6^{\circ}\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the key difference: engines produce work from heat (η<1\eta < 1), while heat pumps move heat using work (COP>1\text{COP} > 1).

  • Practice deriving reversible COPs directly from QdesiredW=QdesiredQH−QC\frac{Q_{\text{desired}}}{W} = \frac{Q_{\text{desired}}}{Q_H - Q_C}.

OverviewACEpath Teacher's Diagnosis

03 The student adds 273.15 instead of subtracting it when converting the temperature from kelvins to degrees Celsius.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    COPHP=Q˙HW˙in=8.501.25=6.80\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}} = \frac{8.50}{1.25} = 6.80

  2. Step 2

    COPHP=THTH−TC  ⟹  6.80=295295−TC  ⟹  295−TC=2956.80=43.38 K  ⟹  TC=295−43.38=251.62 K\text{COP}_{\text{HP}} = \frac{T_H}{T_H - T_C} \implies 6.80 = \frac{295}{295 - T_C} \implies 295 - T_C = \frac{295}{6.80} = 43.38\text{ K} \implies T_C = 295 - 43.38 = 251.62\text{ K}

  3. Step 3

    TC(∘C)=251.62+273.15=524.77∘CT_C(^\circ\text{C}) = 251.62 + 273.15 = 524.77^\circ\text{C}

    Correct

    TC(∘C)=251.62−273.15=−21.53∘C≈−21.6∘CT_C(^\circ\text{C}) = 251.62 - 273.15 = -21.53^\circ\text{C} \approx -21.6^\circ\text{C}

    To convert from kelvins to degrees Celsius, you must subtract 273.15273.15 because T(∘C)=T(K)−273.15T(^\circ\text{C}) = T(\text{K}) - 273.15. Adding 273.15273.15 gives an unphysically hot temperature rather than a cold outdoor winter temperature.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the heat pump coefficient of performance from the given heat and work rates.

You correctly applied the theoretical Carnot limit equation using absolute temperature in kelvins.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Temperature Scale Conversion Error

You inverted the sign in the temperature conversion formula, adding 273.15273.15 instead of subtracting it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the conversion direction between the Celsius and Kelvin scales: remembering that the number 273.15273.15 is involved, but forgetting that the numerical value in Celsius is always smaller than the numerical value in kelvins (T∘C=TK−273.15T_{^\circ\text{C}} = T_{\text{K}} - 273.15).

REASONING PATH
Your ACEpath teacher’s suggested approach
Kelvin to Celsius Conversion
  • T(∘C)=T(K)−273.15T(^\circ\text{C}) = T(\text{K}) - 273.15 and T(K)=T(∘C)+273.15T(\text{K}) = T(^\circ\text{C}) + 273.15

  • Anchor your memory with a known physical benchmark: water freezes at 0∘C=273.15 K0^\circ\text{C} = 273.15\text{ K}. Since 251.62 K<273.15 K251.62\text{ K} < 273.15\text{ K}, the Celsius temperature must be negative.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. TC(∘C)=TC(K)−273.15T_C(^\circ\text{C}) = T_C(\text{K}) - 273.15

  2. TC(∘C)=251.62−273.15=−21.53∘C≈−21.6∘CT_C(^\circ\text{C}) = 251.62 - 273.15 = -21.53^\circ\text{C} \approx -21.6^\circ\text{C}

Final answer

(a) COPHP=6.80\text{COP}_{\text{HP}} = 6.80; (b) TC=252 KT_C = 252\text{ K}; (c) TC=−21.6∘CT_C = -21.6^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always perform a reality check on the sign and magnitude of ambient temperatures in heat pump problems.

  • Memorize the anchor point 0∘C=273.15 K0^\circ\text{C} = 273.15\text{ K} to verify whether you need to add or subtract 273.15273.15.

Lock it in

Similar question

01

A residential Carnot heat pump maintains a room at 21∘C21^\circ\text{C} (294.15 K294.15\text{ K}) by delivering heat at a rate of 6.00 kW6.00\text{ kW}. The compressor consumes 1.50 kW1.50\text{ kW} of electricity. Determine the heating coefficient of performance COPHP\text{COP}_{\text{HP}} and the outdoor temperature TCT_C in kelvins.

Answer

COPHP=4.00\text{COP}_{\text{HP}} = 4.00; TC=221 KT_C = 221\text{ K}.

  1. COPHP=Q˙HW˙in=6.00 kW1.50 kW=4.00\text{COP}_{\text{HP}} = \frac{\dot{Q}_H}{\dot{W}_{\text{in}}} = \frac{6.00\text{ kW}}{1.50\text{ kW}} = 4.00.
  2. For a Carnot heat pump, COPHP=THTH−TC  ⟹  TC=TH(1−1COPHP)=294.15(1−14.00)=220.6 K≈221 K\text{COP}_{\text{HP}} = \frac{T_H}{T_H - T_C} \implies T_C = T_H\left(1 - \frac{1}{\text{COP}_{\text{HP}}}\right) = 294.15\left(1 - \frac{1}{4.00}\right) = 220.6\text{ K} \approx 221\text{ K}.
02

An industrial heat pump operates on a reversible Carnot cycle between a cold river at 5∘C5^\circ\text{C} (278.15 K278.15\text{ K}) and a processing tank at 65∘C65^\circ\text{C} (338.15 K338.15\text{ K}). (a) Calculate the theoretical COPHP\text{COP}_{\text{HP}}. (b) If the heat pump delivers 90.0 kW90.0\text{ kW} of heat to the process tank, how much power must the compressor supply?

Answer

(a) COPHP=5.64\text{COP}_{\text{HP}} = 5.64; (b) W˙in=16.0 kW\dot{W}_{\text{in}} = 16.0\text{ kW}.

  1. COPHP=THTH−TC=338.15338.15−278.15=338.1560.0≈5.636≈5.64\text{COP}_{\text{HP}} = \frac{T_H}{T_H - T_C} = \frac{338.15}{338.15 - 278.15} = \frac{338.15}{60.0} \approx 5.636 \approx 5.64.
  2. W˙in=Q˙HCOPHP=90.0 kW5.636≈15.97 kW≈16.0 kW\dot{W}_{\text{in}} = \frac{\dot{Q}_H}{\text{COP}_{\text{HP}}} = \frac{90.0\text{ kW}}{5.636} \approx 15.97\text{ kW} \approx 16.0\text{ kW}.
03

A geothermal heat pump supplies 12.0 kW12.0\text{ kW} of heat to a building at TH=298 KT_H = 298\text{ K} while absorbing heat from underground ground-loop water at TC=280 KT_C = 280\text{ K}. Assuming it operates at 60%60\% of the maximum theoretical Carnot coefficient of performance, find the actual electrical power input required to drive the heat pump.

Answer

W˙in, actual=1.21 kW\dot{W}_{\text{in, actual}} = 1.21\text{ kW}.

  1. Maximum theoretical COP: COPHP, Carnot=THTH−TC=298 K298 K−280 K=29818≈16.56\text{COP}_{\text{HP, Carnot}} = \frac{T_H}{T_H - T_C} = \frac{298\text{ K}}{298\text{ K} - 280\text{ K}} = \frac{298}{18} \approx 16.56.
  2. Actual COP: COPactual=0.60×16.56≈9.933\text{COP}_{\text{actual}} = 0.60 \times 16.56 \approx 9.933.
  3. Required power input: W˙in=Q˙HCOPactual=12.0 kW9.933≈1.21 kW\dot{W}_{\text{in}} = \frac{\dot{Q}_H}{\text{COP}_{\text{actual}}} = \frac{12.0\text{ kW}}{9.933} \approx 1.21\text{ kW}.
Loading workspace…