Resources

A high-speed experimental rail sled of mass m=350 kgm = 350\text{ kg} traveling horizontally at v0=42.0 m/sv_0 = 42.0\text{ m/s} enters an emergency arresting zone equipped with a progressive linear hydraulic damper. The arresting force exerted on the sled varies with penetration distance xx according to F(x)=bx2F(x) = bx^2, where b=1.65×103 N/m2b = 1.65 \times 10^3\text{ N/m}^2. The mechanical runout limit of the arresting track is xmax=7.50 mx_{\text{max}} = 7.50\text{ m}. Applying the Work-Energy Theorem, determine whether the sled is brought to a complete stop before reaching the end of the track by calculating the exact stopping distance xstopx_{\text{stop}} and the remaining margin to the threshold boundary.

Answer and steps

Final answer

xstop=8.16 mx_{\text{stop}} = 8.16\text{ m}; the sled exceeds the runout limit by 0.66 m0.66\text{ m} and does not stop within the track threshold.

Steps

01

State the Work-Energy Theorem

The Work-Energy Theorem states that the net work done on an object equals the change in its kinetic energy:

Wnet=ΔK=Kf−KiW_{\text{net}} = \Delta K = K_f - K_i

For the sled to come to a complete stop, its final velocity must be zero, giving a final kinetic energy of Kf=0 JK_f = 0\text{ J}.

02

Calculate the Initial Kinetic Energy

Using the given mass m=350 kgm = 350\text{ kg} and initial speed v0=42.0 m/sv_0 = 42.0\text{ m/s}:

Ki=12mv02=12(350 kg)(42.0 m/s)2K_i = \frac{1}{2}m v_0^2 = \frac{1}{2}(350\text{ kg})(42.0\text{ m/s})^2

Ki=175 kg⋅1764 m2/s2=308,700 JK_i = 175\text{ kg} \cdot 1764\text{ m}^2/\text{s}^2 = 308{,}700\text{ J}

03

Determine the Work Done by the Arresting Force

Because the arresting force acts in the direction opposite to the sled's displacement along the horizontal track, the force vector is Fnet(x)=−bx2F_{\text{net}}(x) = -bx^2. The work done from x=0x = 0 to the stopping point xstopx_{\text{stop}} is found by integration:

Wnet=∫0xstop(−bx2) dx=[−bx33]0xstop=−b3xstop3W_{\text{net}} = \int_0^{x_{\text{stop}}} (-bx^2)\,dx = \left[ -\frac{b x^3}{3} \right]_0^{x_{\text{stop}}} = -\frac{b}{3} x_{\text{stop}}^3

Common Pitfall: Because the force is position-dependent (F∝x2F \propto x^2), you cannot simply use W=F⋅dW = F \cdot d with a single constant force value; you must integrate the variable force over the displacement.

04

Solve for the Stopping Distance xstopx_{\text{stop}}

Equating the net work to the change in kinetic energy:

−b3xstop3=0−Ki-\frac{b}{3} x_{\text{stop}}^3 = 0 - K_i

b3xstop3=Ki\frac{b}{3} x_{\text{stop}}^3 = K_i

Rearranging for xstopx_{\text{stop}}:

xstop3=3Kib=3(308,700 J)1.65×103 N/m2x_{\text{stop}}^3 = \frac{3 K_i}{b} = \frac{3(308{,}700\text{ J})}{1.65 \times 10^3\text{ N/m}^2}

xstop3=926,1001650≈561.27 m3x_{\text{stop}}^3 = \frac{926{,}100}{1650} \approx 561.27\text{ m}^3

Taking the cube root:

xstop=(561.27)1/3≈8.16 mx_{\text{stop}} = (561.27)^{1/3} \approx 8.16\text{ m}

05

Compare with the Runout Limit

The mechanical runout threshold of the track is xmax=7.50 mx_{\text{max}} = 7.50\text{ m}. Comparing this limit to the required stopping distance:

Δx=xstop−xmax=8.16 m−7.50 m=0.66 m\Delta x = x_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m}

Since xstop>xmaxx_{\text{stop}} > x_{\text{max}}, the sled does not stop within the designated arresting zone and overshoots the track threshold by 0.66 m0.66\text{ m}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student treats the variable arresting force as constant or forgets to integrate, using W = F·x = bx³ instead of integrating ∫ bx² dx = (1/3)bx³.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ki=12mv02=0.5×350×42.02=308700 JK_i = \frac{1}{2}m v_0^2 = 0.5 \times 350 \times 42.0^2 = 308700\text{ J}

  2. Step 2

    W=F×x=(bx2)×x=bx3W = F \times x = (bx^2) \times x = bx^3

    Correct

    ∣W∣=∫0xstopF(x) dx=∫0xstopbx2 dx=13bxstop3|W| = \int_0^{x_{\text{stop}}} F(x)\,dx = \int_0^{x_{\text{stop}}} bx^2\,dx = \frac{1}{3}b x_{\text{stop}}^3

    The arresting force varies with position according to F(x)=bx2F(x) = bx^2, so work cannot be calculated using the constant-force formula W=F⋅xW = F \cdot x. You must integrate the force over the displacement: ∫0xbx2 dx=13bx3\int_0^x bx^2\,dx = \frac{1}{3}bx^3.

  3. Step 3

    1650x3=308700  ⟹  x3=187.09  ⟹  xstop=5.72 m1650 x^3 = 308700 \implies x^3 = 187.09 \implies x_{\text{stop}} = 5.72\text{ m}

    Correct

    13(1650)xstop3=308,700  ⟹  xstop3=561.27  ⟹  xstop≈8.16 m\frac{1}{3}(1650)x_{\text{stop}}^3 = 308{,}700 \implies x_{\text{stop}}^3 = 561.27 \implies x_{\text{stop}} \approx 8.16\text{ m}

    Your algebra correctly followed from your work expression, but because the work formula lacked the 13\frac{1}{3} integration factor, your stopping distance was underestimated.

  4. Step 4

    Margin=7.50−5.72=1.78 m  ⟹  The sled stops before the end with 1.78 m of remaining margin.\text{Margin} = 7.50 - 5.72 = 1.78\text{ m} \implies \text{The sled stops before the end with } 1.78\text{ m of remaining margin.}

    Correct

    Δx=xstop−xmax=8.16 m−7.50 m=0.66 m  ⟹  The sled overshoots the track threshold by 0.66 m.\Delta x = x_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m} \implies \text{The sled overshoots the track threshold by } 0.66\text{ m.}

    Because the true stopping distance is 8.16 m8.16\text{ m}, which exceeds the track limit of 7.50 m7.50\text{ m}, the sled actually overshoots the boundary by 0.66 m0.66\text{ m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the initial kinetic energy using Ki=12mv02K_i = \frac{1}{2}m v_0^2.

You correctly recognized that the stopping distance is found by equating work done to initial kinetic energy.

You correctly solved for xx by taking the cube root of both sides.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Variable force work treated as constant force

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied the constant-force formula W=F⋅xW = F \cdot x to a spatially varying force F(x)=bx2F(x) = bx^2 rather than setting up a definite integral W=∫F(x) dxW = \int F(x)\,dx.

REASONING PATH
Your ACEpath teacher’s suggested approach
Constant vs. Variable Force Check
  • The formula W=F⋅dW = F \cdot d is only valid when FF is constant. Whenever force depends on position xx, work must be calculated as W=∫xixfF(x) dxW = \int_{x_i}^{x_f} F(x)\,dx.

  • Before calculating work, inspect whether the force contains the variable xx. If it does, write the integral ∫F(x) dx\int F(x)\,dx immediately.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the work integral for the variable force: ∣W∣=∫0xstopbx2 dx=[bx33]0xstop=13bxstop3|W| = \int_0^{x_{\text{stop}}} bx^2\,dx = \left[ \frac{bx^3}{3} \right]_0^{x_{\text{stop}}} = \frac{1}{3} b x_{\text{stop}}^3

  2. Equate the work done to the initial kinetic energy: 13(1650 N/m2)xstop3=308,700 J\frac{1}{3}(1650\text{ N/m}^2) x_{\text{stop}}^3 = 308{,}700\text{ J}

  3. Solve for xstop3x_{\text{stop}}^3: xstop3=3×308,7001650=561.27 m3x_{\text{stop}}^3 = \frac{3 \times 308{,}700}{1650} = 561.27\text{ m}^3

  4. Take the cube root to find the stopping distance: xstop=(561.27)1/3≈8.16 mx_{\text{stop}} = (561.27)^{1/3} \approx 8.16\text{ m}

  5. Compare with the runout limit: xstop−xmax=8.16 m−7.50 m=0.66 mx_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m} overshoot

Final answer

xstop=8.16 mx_{\text{stop}} = 8.16\text{ m}; the sled exceeds the runout limit by 0.66 m0.66\text{ m} and fails to stop within the designated arresting zone.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review calculating work for variable forces by identifying the position dependence and applying polynomial integration rules.

  • Practice distinguishing between linear damping forces, quadratic restoring forces, and constant friction forces when setting up work-energy equations.

OverviewACEpath Teacher's Diagnosis

02 The student misintegrates x² as x³/2 instead of x³/3, leading to an incorrect stopping distance of 7.21 m.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ki=12mv02=0.5×350×422=308700 JK_i = \frac{1}{2} m v_0^2 = 0.5 \times 350 \times 42^2 = 308700\text{ J}

  2. Step 2

    W=∫bx2 dx=12bx3W = \int bx^2\,dx = \frac{1}{2}bx^3

    Correct

    ∣W∣=∫0xstopbx2 dx=[bx33]0xstop=13bxstop3|W| = \int_0^{x_{\text{stop}}} bx^2\,dx = \left[ \frac{b x^3}{3} \right]_0^{x_{\text{stop}}} = \frac{1}{3}bx_{\text{stop}}^3

    When integrating x2x^2, the power rule states that ∫xn dx=xn+1n+1\int x^n\,dx = \frac{x^{n+1}}{n+1}. For n=2n=2, the denominator must be 2+1=32+1=3, giving 13bx3\frac{1}{3}bx^3 rather than 12bx3\frac{1}{2}bx^3.

  3. Step 3

    12×1650×x3=308700⟹825x3=308700⟹x3=374.18⟹xstop=7.21 m\frac{1}{2} \times 1650 \times x^3 = 308700 \Longrightarrow 825 x^3 = 308700 \Longrightarrow x^3 = 374.18 \Longrightarrow x_{\text{stop}} = 7.21\text{ m}

    Correct

    13(1650)xstop3=308,700⟹550xstop3=308,700⟹xstop3≈561.27⟹xstop≈8.16 m\frac{1}{3}(1650)x_{\text{stop}}^3 = 308{,}700 \Longrightarrow 550 x_{\text{stop}}^3 = 308{,}700 \Longrightarrow x_{\text{stop}}^3 \approx 561.27 \Longrightarrow x_{\text{stop}} \approx 8.16\text{ m}

    Your algebra and cube-root evaluation were carried out properly, but this step inherits the incorrect prefactor from step 2.

  4. Step 4

    Margin=7.50−7.21=0.29 m⟹The sled stops before reaching the end with 0.29 m remaining.\text{Margin} = 7.50 - 7.21 = 0.29\text{ m} \Longrightarrow \text{The sled stops before reaching the end with } 0.29\text{ m remaining.}

    Correct

    Δx=xstop−xmax=8.16 m−7.50 m=0.66 m⟹The sled exceeds the limit by 0.66 m and does not stop in time.\Delta x = x_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m} \Longrightarrow \text{The sled exceeds the limit by } 0.66\text{ m and does not stop in time.}

    Because your stopping distance was artificially low, your margin calculation and final conclusion were reversed.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that stopping requires all initial kinetic energy to be dissipated by the arresting force.

You correctly calculated the initial kinetic energy as 308,700 J308{,}700\text{ J}.

You recognized that a position-dependent force requires integration to find the work done.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Calculus Integration Error

You accidentally divided by 22 instead of the new exponent 33 when integrating x2x^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the coefficient 12\frac{1}{2} from the kinetic energy or linear spring work formula (W=12kx2W = \frac{1}{2}kx^2) with the calculus power rule for higher-order powers ∫xn dx=xn+1n+1\int x^n\,dx = \frac{x^{n+1}}{n+1}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Power Rule Check
  • For any power n≠−1n \neq -1, ∫xn dx=xn+1n+1+C\int x^n\,dx = \frac{x^{n+1}}{n+1} + C.

  • Always verify that the denominator in the antiderivative matches the newly incremented exponent.

Physical Reality Check
  • Dividing by a smaller number (22 instead of 33) overestimates the work done for a given displacement, making the calculated stopping distance too short.

  • Differentiate your antiderivative ddx(13bx3)=bx2\frac{d}{dx}\left(\frac{1}{3}bx^3\right) = bx^2 before proceeding to algebraic substitution.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the net work done by the damper equal to the sled's loss of kinetic energy: ∫0xstopbx2 dx=Ki\int_0^{x_{\text{stop}}} bx^2\,dx = K_i.

  2. Apply the power rule correctly: [bx33]0xstop=b3xstop3\left[ \frac{b x^3}{3} \right]_0^{x_{\text{stop}}} = \frac{b}{3} x_{\text{stop}}^3.

  3. Substitute the numerical values: 16503xstop3=308,700⟹550xstop3=308,700\frac{1650}{3} x_{\text{stop}}^3 = 308{,}700 \Longrightarrow 550 x_{\text{stop}}^3 = 308{,}700.

  4. Solve for xstopx_{\text{stop}}: xstop3=561.27⟹xstop≈8.16 mx_{\text{stop}}^3 = 561.27 \Longrightarrow x_{\text{stop}} \approx 8.16\text{ m}.

  5. Compare with the runout limit: xstop−xmax=8.16 m−7.50 m=0.66 mx_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m}.

Final answer

xstop=8.16 mx_{\text{stop}} = 8.16\text{ m}; the sled overshoots the runout threshold by 0.66 m0.66\text{ m} and fails to stop within the designated arresting zone.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the basic power rule of integration, ensuring you match the denominator to the incremented exponent.

  • Perform a quick derivative check on your integrated work expressions before plugging in numerical values.

  • Practice work-energy problems with variable force functions such as F(x)=cx3F(x) = c x^3 and F(x)=kxF(x) = k \sqrt{x}.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to square the initial velocity when calculating the initial kinetic energy, calculating K = 1/2 m v_0.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ki=12mv0=0.5×350×42.0=7350 JK_i = \frac{1}{2}mv_0 = 0.5 \times 350 \times 42.0 = 7350\text{ J}

    Correct

    Ki=12mv02=12(350 kg)(42.0 m/s)2=308,700 JK_i = \frac{1}{2}mv_0^2 = \frac{1}{2}(350\text{ kg})(42.0\text{ m/s})^2 = 308{,}700\text{ J}

    You forgot to square the initial velocity v0v_0 in the kinetic energy formula. Kinetic energy is proportional to the square of velocity (v2v^2), not velocity itself.

  2. Step 2

    W=∫bx2 dx=13bx3W = \int bx^2\,dx = \frac{1}{3}bx^3

  3. Step 3

    13×1650×x3=7350  ⟹  550x3=7350  ⟹  x3=13.36  ⟹  xstop=2.37 m\frac{1}{3} \times 1650 \times x^3 = 7350 \implies 550x^3 = 7350 \implies x^3 = 13.36 \implies x_{\text{stop}} = 2.37\text{ m}

    Correct

    550xstop3=308,700  ⟹  xstop3=561.27  ⟹  xstop≈8.16 m550x_{\text{stop}}^3 = 308{,}700 \implies x_{\text{stop}}^3 = 561.27 \implies x_{\text{stop}} \approx 8.16\text{ m}

    Your algebra and cube-root evaluation were carried out properly, but the result was thrown off by the incorrect initial kinetic energy value from Step 1.

  4. Step 4

    Margin=7.50−2.37=5.13 m  ⟹  The sled stops before the track limit with 5.13 m remaining.\text{Margin} = 7.50 - 2.37 = 5.13\text{ m} \implies \text{The sled stops before the track limit with } 5.13\text{ m} \text{ remaining.}

    Correct

    xstop−xmax=8.16 m−7.50 m=0.66 m  ⟹  The sled overshoots the track limit by 0.66 m.x_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m} \implies \text{The sled overshoots the track limit by } 0.66\text{ m}.

    Because your calculated stopping distance was 2.37 m2.37\text{ m} instead of 8.16 m8.16\text{ m}, your final conclusion was reversed.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that a variable force requires integrating F(x) dxF(x)\,dx to find work.

You successfully integrated ∫bx2 dx\int bx^2\,dx to get 13bx3\frac{1}{3}bx^3.

You correctly equated the work done by the damper to the initial kinetic energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Recall Error (Kinetic Energy)

You wrote K=12mvK = \frac{1}{2}mv instead of K=12mv2K = \frac{1}{2}mv^2, omitting the square on the velocity term.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing kinetic energy with momentum or dropping the quadratic exponent in translational kinetic energy when transcribing the formula.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis of Energy
  • Energy has dimensions of mass×length2/time2\text{mass} \times \text{length}^2 / \text{time}^2 (Joules, or kg⋅m2/s2\text{kg}\cdot\text{m}^2/\text{s}^2).

  • Always verify that your velocity is squared; mvm v has units of momentum (kg⋅m/s\text{kg}\cdot\text{m/s}), while 12mv2\frac{1}{2}mv^2 has units of energy (J\text{J}).

Variable Force Work Integration
  • W=∫xixfF(x) dxW = \int_{x_i}^{x_f} F(x)\,dx for non-constant forces.

  • Maintain the integral form and evaluate boundaries explicitly between 00 and xstopx_{\text{stop}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate initial kinetic energy correctly: Ki=12mv02=12(350 kg)(42.0 m/s)2=308,700 JK_i = \frac{1}{2} m v_0^2 = \frac{1}{2}(350\text{ kg})(42.0\text{ m/s})^2 = 308{,}700\text{ J}.

  2. Equate the magnitude of the arresting work to kinetic energy: 13bxstop3=Ki  ⟹  13(1650 N/m2)xstop3=308,700 J\frac{1}{3}bx_{\text{stop}}^3 = K_i \implies \frac{1}{3}(1650\text{ N/m}^2)x_{\text{stop}}^3 = 308{,}700\text{ J}.

  3. Solve for stopping distance: 550xstop3=308,700  ⟹  xstop3≈561.27  ⟹  xstop≈8.16 m550 x_{\text{stop}}^3 = 308{,}700 \implies x_{\text{stop}}^3 \approx 561.27 \implies x_{\text{stop}} \approx 8.16\text{ m}.

  4. Compare with the track threshold: xstop−xmax=8.16 m−7.50 m=0.66 mx_{\text{stop}} - x_{\text{max}} = 8.16\text{ m} - 7.50\text{ m} = 0.66\text{ m}.

Final answer

xstop=8.16 mx_{\text{stop}} = 8.16\text{ m}; the sled overshoots the runout limit by 0.66 m0.66\text{ m} and fails to stop within the designated arresting track.

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that kinetic energy formulas always include v2v^2 before calculating numerical values.

  • Perform a quick unit check on energy calculations to ensure the units match Joules (kg⋅m2/s2\text{kg}\cdot\text{m}^2/\text{s}^2).

  • Re-evaluate whether a vehicle overshoots or halts based on the correct stopping distance.

Lock it in

Similar question

01

A 200 kg200\text{ kg} cart moving at 10 m/s10\text{ m/s} is stopped by a bumper that exerts a resistive force F(x)=cxF(x) = cx, where c=800 N/mc = 800\text{ N/m}. Using the Work-Energy Theorem, find the maximum compression xx of the bumper.

Answer

x=5.0 mx = 5.0\text{ m}. Initial kinetic energy: Ki=12(200)(102)=10,000 JK_i = \frac{1}{2}(200)(10^2) = 10{,}000\text{ J}. Work done by the variable force: W=∫0xcx dx=12cx2=12(800)x2=400x2W = \int_0^x cx\,dx = \frac{1}{2}cx^2 = \frac{1}{2}(800)x^2 = 400x^2. Equating work to kinetic energy gives 400x2=10,000  ⟹  x2=25  ⟹  x=5.0 m400x^2 = 10{,}000 \implies x^2 = 25 \implies x = 5.0\text{ m}.

02

An object of mass m=4.0 kgm = 4.0\text{ kg} enters a resistive medium where the retarding force is F(x)=kx2F(x) = kx^2 with k=300 N/m2k = 300\text{ N/m}^2. If the object penetrates a distance of 2.0 m2.0\text{ m} before coming to rest, what was its initial speed v0v_0?

Answer

v0=20 m/sv_0 = 20\text{ m/s}. The work done to stop the object is W=∫02300x2 dx=[100x3]02=800 JW = \int_0^2 300x^2\,dx = [100x^3]_0^2 = 800\text{ J}. By the Work-Energy Theorem, 12mv02=W  ⟹  12(4.0)v02=800  ⟹  2.0v02=800  ⟹  v02=400  ⟹  v0=20 m/s\frac{1}{2}m v_0^2 = W \implies \frac{1}{2}(4.0)v_0^2 = 800 \implies 2.0 v_0^2 = 800 \implies v_0^2 = 400 \implies v_0 = 20\text{ m/s}.

03

A test vehicle of mass 500 kg500\text{ kg} traveling at 30 m/s30\text{ m/s} enters an arresting barrier where the braking force has both a constant friction component and a quadratic hydrodynamic component: F(x)=F0+bx2F(x) = F_0 + bx^2, with F0=5.0×103 NF_0 = 5.0 \times 10^3\text{ N} and b=1.2×103 N/m2b = 1.2 \times 10^3\text{ N/m}^2. Set up the work-energy equation and determine whether the stopping distance is less than or greater than 6.0 m6.0\text{ m}.

Answer

The stopping distance is greater than 6.0 m6.0\text{ m} (xstop≈7.02 mx_{\text{stop}} \approx 7.02\text{ m}). Initial energy is Ki=12(500)(302)=225,000 JK_i = \frac{1}{2}(500)(30^2) = 225{,}000\text{ J}. Work as a function of penetration is W(x)=∫0x(F0+bx2) dx=F0x+13bx3W(x) = \int_0^x (F_0 + bx^2)\,dx = F_0 x + \frac{1}{3}bx^3. Evaluating at x=6.0 mx = 6.0\text{ m} gives W(6.0)=(5000)(6.0)+13(1200)(6.03)=30,000+86,400=116,400 JW(6.0) = (5000)(6.0) + \frac{1}{3}(1200)(6.0^3) = 30{,}000 + 86{,}400 = 116{,}400\text{ J}. Since W(6.0)<225,000 JW(6.0) < 225{,}000\text{ J}, the vehicle has not yet stopped at 6.0 m6.0\text{ m}.

Loading workspace…