Resources

Two rigid, immovable abutments are separated by an initial gap of w0=1.44 mmw_0 = 1.44\text{ mm} at T0=18.0∘CT_0 = 18.0^\circ\text{C}. A solid horizontal copper rod of unstressed length L0=1.200 mL_0 = 1.200\text{ m} is pinned to the left abutment and extends toward the right abutment. The copper rod has a linear expansion coefficient of α=1.70×10−5 ∘C−1\alpha = 1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1}, cross-sectional area A=4.50×10−4 m2A = 4.50 \times 10^{-4}\text{ m}^2, and Young's modulus Y=1.10×1011 N/m2Y = 1.10 \times 10^{11}\text{ N/m}^2. (a) Determine the threshold temperature TcontactT_{\text{contact}} at which the rod just bridges the gap and touches the right abutment. (b) If the temperature continues to rise to Tf=115.0∘CT_f = 115.0^\circ\text{C}, calculate the magnitude of the compressive thermal stress σ\sigma developed inside the rod.

Answer and steps

Final answer

(a) Tcontact=88.6∘CT_{\text{contact}} = 88.6^\circ\text{C}; (b) σ=4.94×107 Pa\sigma = 4.94 \times 10^7\text{ Pa}

Steps

Part (a): Temperature at Contact

As the temperature increases, the copper rod expands linearly according to the thermal expansion formula: ΔL=αL0ΔT\Delta L = \alpha L_0 \Delta T

where:

  • L0=1.200 mL_0 = 1.200\text{ m} is the initial length of the rod,
  • α=1.70×10−5 ∘C−1\alpha = 1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1} is the coefficient of linear expansion,
  • ΔT=Tcontact−T0\Delta T = T_{\text{contact}} - T_0 is the change in temperature.

The rod expands freely into the open gap without experiencing any internal stress until its elongation equals the initial gap width w0=1.44 mm=1.44×10−3 mw_0 = 1.44\text{ mm} = 1.44 \times 10^{-3}\text{ m}: ΔL=w0\Delta L = w_0

Substitute the given values to solve for the temperature rise required to close the gap: ΔT=w0αL0=1.44×10−3 m(1.70×10−5 ∘C−1)(1.200 m)=1.44×10−32.04×10−5 ∘C≈70.59∘C\Delta T = \frac{w_0}{\alpha L_0} = \frac{1.44 \times 10^{-3}\text{ m}}{(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(1.200\text{ m})} = \frac{1.44 \times 10^{-3}}{2.04 \times 10^{-5}}\text{ }^\circ\text{C} \approx 70.59^\circ\text{C}

Now, add this temperature rise to the initial temperature T0=18.0∘CT_0 = 18.0^\circ\text{C}: Tcontact=T0+ΔT=18.0∘C+70.59∘C=88.59∘C≈88.6∘CT_{\text{contact}} = T_0 + \Delta T = 18.0^\circ\text{C} + 70.59^\circ\text{C} = 88.59^\circ\text{C} \approx 88.6^\circ\text{C}


Part (b): Compressive Thermal Stress

1. Identify the constrained temperature range

A common pitfall is calculating the thermal stress using the entire temperature difference (Tf−T0)(T_f - T_0). However, from T0T_0 to TcontactT_{\text{contact}}, the rod expands freely, so no stress develops. Compressive stress builds up only after contact is made, as the rigid abutments prevent any additional thermal elongation: ΔTconstrained=Tf−Tcontact=115.0∘C−88.59∘C=26.41∘C\Delta T_{\text{constrained}} = T_f - T_{\text{contact}} = 115.0^\circ\text{C} - 88.59^\circ\text{C} = 26.41^\circ\text{C}

2. Relate thermal strain to compressive stress

If the rod were free to expand over this temperature rise, it would experience a further thermal strain of: ϵ=αΔTconstrained\epsilon = \alpha \Delta T_{\text{constrained}}

Because the rigid walls strictly prevent this expansion, the abutments exert a compressive force that provides an equal and opposite mechanical strain. By Hooke's Law, the resulting compressive stress σ\sigma is: σ=Yϵ=YαΔTconstrained\sigma = Y \epsilon = Y \alpha \Delta T_{\text{constrained}}

3. Compute the stress magnitude

Substitute the known quantities: σ=(1.10×1011 N/m2)(1.70×10−5 ∘C−1)(26.41∘C)\sigma = (1.10 \times 10^{11}\text{ N/m}^2)(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(26.41^\circ\text{C}) σ=(1.87×106 Pa/∘C)(26.41∘C)≈4.94×107 Pa\sigma = (1.87 \times 10^6\text{ Pa/}^\circ\text{C})(26.41^\circ\text{C}) \approx 4.94 \times 10^7\text{ Pa}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates thermal stress using the total temperature rise from the initial temperature instead of only the temperature increase after contact occurs.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔL=α⋅L0⋅ΔT=w0  ⟹  ΔT=1.44×10−31.70×10−5⋅1.200=70.6∘C\Delta L = \alpha \cdot L_0 \cdot \Delta T = w_0 \implies \Delta T = \frac{1.44 \times 10^{-3}}{1.70 \times 10^{-5} \cdot 1.200} = 70.6^\circ\text{C}

  2. Step 2

    Tcontact=18.0+70.6=88.6∘CT_{\text{contact}} = 18.0 + 70.6 = 88.6^\circ\text{C}

  3. Step 3

    ΔTtotal=115.0−18.0=97.0∘C\Delta T_{\text{total}} = 115.0 - 18.0 = 97.0^\circ\text{C}

    Correct

    ΔTconstrained=Tf−Tcontact=115.0∘C−88.6∘C=26.4∘C\Delta T_{\text{constrained}} = T_f - T_{\text{contact}} = 115.0^\circ\text{C} - 88.6^\circ\text{C} = 26.4^\circ\text{C}

    Before contact, the rod expands freely into the gap with zero stress. Internal compressive stress only builds up during the subsequent temperature increase after contact occurs.

  4. Step 4

    σ=Y⋅α⋅ΔTtotal=1.10×1011⋅1.70×10−5⋅97.0=1.81×108 N/m2\sigma = Y \cdot \alpha \cdot \Delta T_{\text{total}} = 1.10 \times 10^{11} \cdot 1.70 \times 10^{-5} \cdot 97.0 = 1.81 \times 10^8\text{ N/m}^2

    Correct

    σ=YαΔTconstrained=(1.10×1011 Pa)(1.70×10−5 ∘C−1)(26.4∘C)≈4.94×107 Pa\sigma = Y \alpha \Delta T_{\text{constrained}} = (1.10 \times 10^{11}\text{ Pa})(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(26.4^\circ\text{C}) \approx 4.94 \times 10^7\text{ Pa}

    Your stress formula and calculation followed correctly from your temperature change, but the resulting numerical value was overestimated because it included the free-expansion phase.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the linear expansion equation ΔL=αL0ΔT\Delta L = \alpha L_0 \Delta T to find the temperature increase needed to bridge the gap.

You calculated the contact temperature Tcontact=88.6∘CT_{\text{contact}} = 88.6^\circ\text{C} accurately.

You correctly recalled the thermal stress formula σ=YαΔT\sigma = Y \alpha \Delta T for constrained expansion.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Thermal stress over free expansion interval

You used the total temperature rise ΔT=Tf−T0\Delta T = T_f - T_0 instead of the constrained temperature rise ΔT=Tf−Tcontact\Delta T = T_f - T_{\text{contact}}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing unconstrained thermal expansion with constrained thermal stress. Thermal stress only develops when an external boundary restricts expansion; free expansion creates zero internal stress.

REASONING PATH
Your ACEpath teacher’s suggested approach
Free vs. Constrained Expansion
  • Stress develops only when thermal expansion is prevented by rigid boundaries: σ=Yϵprevented\sigma = Y \epsilon_{\text{prevented}}.

  • Always split the temperature range into two stages: Stage 1 (free expansion until contact, σ=0\sigma = 0) and Stage 2 (fully constrained expansion, σ=YαΔTconstrained\sigma = Y \alpha \Delta T_{\text{constrained}}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the temperature rise that occurs while the rod is constrained: ΔTconstrained=Tf−Tcontact=115.0∘C−88.59∘C=26.41∘C\Delta T_{\text{constrained}} = T_f - T_{\text{contact}} = 115.0^\circ\text{C} - 88.59^\circ\text{C} = 26.41^\circ\text{C}.

  2. Apply Hooke's Law for the constrained expansion: σ=YαΔTconstrained=(1.10×1011 N/m2)(1.70×10−5 ∘C−1)(26.41∘C)\sigma = Y \alpha \Delta T_{\text{constrained}} = (1.10 \times 10^{11}\text{ N/m}^2)(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(26.41^\circ\text{C}).

  3. Evaluate the compressive stress: σ≈4.94×107 Pa\sigma \approx 4.94 \times 10^7\text{ Pa}.

Final answer

(a) Tcontact=88.6∘CT_{\text{contact}} = 88.6^\circ\text{C}; (b) σ=4.94×107 Pa\sigma = 4.94 \times 10^7\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between free thermal expansion (which produces strain without stress) and constrained thermal expansion (which produces stress without further change in length).

  • When a gap is present, always subtract the contact temperature from the final temperature before calculating thermal stress.

  • Complete the targeted flashcards and practice problems below to master two-stage thermal expansion problems.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the temperature rise needed to close the gap as the contact temperature itself without adding the initial temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔL=α⋅L0⋅ΔT=w0  ⟹  ΔT=1.44×10−31.70×10−5⋅1.200=70.6 ∘C\Delta L = \alpha \cdot L_0 \cdot \Delta T = w_0 \implies \Delta T = \frac{1.44 \times 10^{-3}}{1.70 \times 10^{-5} \cdot 1.200} = 70.6\text{ }^\circ\text{C}

  2. Step 2

    Tcontact=70.6 ∘CT_{\text{contact}} = 70.6\text{ }^\circ\text{C}

    Correct

    Tcontact=T0+ΔT=18.0 ∘C+70.59 ∘C≈88.6 ∘CT_{\text{contact}} = T_0 + \Delta T = 18.0\text{ }^\circ\text{C} + 70.59\text{ }^\circ\text{C} \approx 88.6\text{ }^\circ\text{C}

    You set TcontactT_{\text{contact}} equal to ΔT\Delta T. Because the rod starts at an initial temperature of T0=18.0 ∘CT_0 = 18.0\text{ }^\circ\text{C}, you must add this initial temperature to the temperature rise: Tcontact=T0+ΔTT_{\text{contact}} = T_0 + \Delta T.

  3. Step 3

    ΔTstress=115.0−70.6=44.4 ∘C\Delta T_{\text{stress}} = 115.0 - 70.6 = 44.4\text{ }^\circ\text{C}

    Correct

    ΔTconstrained=Tf−Tcontact=115.0 ∘C−88.59 ∘C=26.41 ∘C\Delta T_{\text{constrained}} = T_f - T_{\text{contact}} = 115.0\text{ }^\circ\text{C} - 88.59\text{ }^\circ\text{C} = 26.41\text{ }^\circ\text{C}

    Your reasoning that stress develops only between TcontactT_{\text{contact}} and TfT_f is conceptually sound, but substituting your incorrect value for TcontactT_{\text{contact}} produced an overstated constrained temperature interval.

  4. Step 4

    σ=Y⋅α⋅ΔTstress  ⟹  σ=1.10×1011⋅1.70×10−5⋅44.4=8.30×107 N/m2\sigma = Y \cdot \alpha \cdot \Delta T_{\text{stress}} \implies \sigma = 1.10 \times 10^{11} \cdot 1.70 \times 10^{-5} \cdot 44.4 = 8.30 \times 10^7\text{ N/m}^2

    Correct

    σ=YαΔTconstrained=(1.10×1011 N/m2)(1.70×10−5 ∘C−1)(26.41 ∘C)≈4.94×107 Pa\sigma = Y \alpha \Delta T_{\text{constrained}} = (1.10 \times 10^{11}\text{ N/m}^2)(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(26.41\text{ }^\circ\text{C}) \approx 4.94 \times 10^7\text{ Pa}

    You applied Hooke's law and thermal expansion formulas correctly, but the numerical answer inherits the error from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the linear thermal expansion formula to determine the temperature rise needed to close the gap.

You correctly identified that stress only develops after the rod touches the opposite abutment.

You correctly applied Hooke's law relating Young's modulus, thermal strain, and compressive stress.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Temperature vs. Temperature Change Confusion

You treated the temperature change ΔT=70.6 ∘C\Delta T = 70.6\text{ }^\circ\text{C} as the absolute contact temperature TcontactT_{\text{contact}}, forgetting to add the initial baseline temperature T0=18.0 ∘CT_0 = 18.0\text{ }^\circ\text{C}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing a temperature interval (ΔT\Delta T) with a state temperature (TT). In thermal mechanics, equations like ΔL=αL0ΔT\Delta L = \alpha L_0 \Delta T yield the change ΔT=Tfinal−Tinitial\Delta T = T_{\text{final}} - T_{\text{initial}}, so finding an absolute temperature threshold requires adding the starting temperature.

REASONING PATH
Your ACEpath teacher’s suggested approach
State Temperature vs. Temperature Change
  • Whenever an equation solves for ΔT\Delta T, remember that ΔT=Tf−Ti\Delta T = T_f - T_i, which means Tf=Ti+ΔTT_f = T_i + \Delta T.

  • Always write out Tf=T0+ΔTT_f = T_0 + \Delta T explicitly before substituting numbers.

Constrained Interval Verification
  • Thermal stress builds up only during the constrained portion of the heating: ΔTconstrained=Tf−Tcontact\Delta T_{\text{constrained}} = T_f - T_{\text{contact}}.

  • Double-check that T0<Tcontact<TfT_0 < T_{\text{contact}} < T_f and that the sum of the free expansion interval and constrained interval equals the total temperature change (Tf−T0)(T_f - T_0).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Add the initial temperature to find the true threshold: Tcontact=T0+ΔT=18.0∘C+70.59∘C≈88.6∘CT_{\text{contact}} = T_0 + \Delta T = 18.0^\circ\text{C} + 70.59^\circ\text{C} \approx 88.6^\circ\text{C}.

  2. Compute the constrained temperature rise: ΔTconstrained=Tf−Tcontact=115.0∘C−88.59∘C=26.41∘C\Delta T_{\text{constrained}} = T_f - T_{\text{contact}} = 115.0^\circ\text{C} - 88.59^\circ\text{C} = 26.41^\circ\text{C}.

  3. Calculate the compressive thermal stress: σ=YαΔTconstrained=(1.10×1011)(1.70×10−5)(26.41)≈4.94×107 Pa\sigma = Y \alpha \Delta T_{\text{constrained}} = (1.10 \times 10^{11})(1.70 \times 10^{-5})(26.41) \approx 4.94 \times 10^7\text{ Pa}.

Final answer

(a) Tcontact=88.6∘CT_{\text{contact}} = 88.6^\circ\text{C}; (b) σ=4.94×107 Pa\sigma = 4.94 \times 10^7\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between absolute temperature TT and temperature differential ΔT\Delta T in thermal problems.

  • Work through practice problems where expansion is partially free and partially constrained.

  • Complete the targeted flashcards and practice exercises below to solidify your understanding.

OverviewACEpath Teacher's Diagnosis

03 The student neglects the unit conversion of the gap width from millimeters to meters, making the required expansion 1000 times too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔL=α⋅L0⋅ΔT=1.44  ⟹  ΔT=1.441.70×10−5⋅1.200=70588∘C\Delta L = \alpha \cdot L_0 \cdot \Delta T = 1.44 \implies \Delta T = \frac{1.44}{1.70 \times 10^{-5} \cdot 1.200} = 70588^\circ\text{C}

    Correct

    ΔL=w0=1.44×10−3 m  ⟹  ΔT=1.44×10−3 m(1.70×10−5 ∘C−1)(1.200 m)≈70.6∘C\Delta L = w_0 = 1.44 \times 10^{-3}\text{ m} \implies \Delta T = \frac{1.44 \times 10^{-3}\text{ m}}{(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(1.200\text{ m})} \approx 70.6^\circ\text{C}

    You set up the expansion formula correctly, but you substituted the gap width w0=1.44 mmw_0 = 1.44\text{ mm} as 1.44 m1.44\text{ m} without converting millimeters to meters (1.44 mm=1.44×10−3 m1.44\text{ mm} = 1.44 \times 10^{-3}\text{ m}). This made your required temperature rise 10310^3 times too large.

  2. Step 2

    Tcontact=18.0+70588=70606∘CT_{\text{contact}} = 18.0 + 70588 = 70606^\circ\text{C}

    Correct

    Tcontact=T0+ΔT=18.0∘C+70.59∘C≈88.6∘CT_{\text{contact}} = T_0 + \Delta T = 18.0^\circ\text{C} + 70.59^\circ\text{C} \approx 88.6^\circ\text{C}

    You correctly added your calculated ΔT\Delta T to the initial temperature T0T_0, but the numerical value was affected by the unit conversion error in Step 1.

  3. Step 3

    Tcontact>115.0∘C, so the rod never touches the right abutment.  ⟹  σ=0 N/m2T_{\text{contact}} > 115.0^\circ\text{C}\text{, so the rod never touches the right abutment.} \implies \sigma = 0\text{ N/m}^2

    Correct

    ΔTconstrained=115.0∘C−88.59∘C=26.41∘C  ⟹  σ=YαΔTconstrained≈4.94×107 Pa\Delta T_{\text{constrained}} = 115.0^\circ\text{C} - 88.59^\circ\text{C} = 26.41^\circ\text{C} \implies \sigma = Y \alpha \Delta T_{\text{constrained}} \approx 4.94 \times 10^7\text{ Pa}

    Because your contact temperature was erroneously high, you concluded that the rod never reaches the abutment. Since the true contact temperature is 88.6∘C<115.0∘C88.6^\circ\text{C} < 115.0^\circ\text{C}, the rod is constrained from 88.6∘C88.6^\circ\text{C} to 115.0∘C115.0^\circ\text{C} and develops compressive stress.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the rod must expand by the gap width ΔL=w0\Delta L = w_0 to make contact.

You applied the linear thermal expansion formula ΔL=αL0ΔT\Delta L = \alpha L_0 \Delta T to relate temperature change to length change.

You understood that thermal stress only develops when expansion is physically constrained.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of metric prefix unit conversion

You entered 1.441.44 directly into your calculation instead of 1.44×10−3 m1.44 \times 10^{-3}\text{ m}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inattention to dimensional consistency between lengths expressed in millimeters and standard SI base units (meters) required by α\alpha and L0L_0.

REASONING PATH
Your ACEpath teacher’s suggested approach
Length Unit Compatibility Check
  • All lengths in thermal expansion formulas must share the same unit as L0L_0 (typically SI meters, m\text{m}).

  • Always write the explicit units next to each variable before rearranging, especially when quantities are given in millimeters or centimeters.

Physical Plausibility Check
  • Thermal expansion coefficients for metals are on the order of 10−5 ∘C−110^{-5}\text{ }^\circ\text{C}^{-1}, so closing a small gap of ∼1 mm\sim 1\text{ mm} requires tens of degrees, not tens of thousands of degrees.

  • Check whether a result such as ΔT≈70000∘C\Delta T \approx 70000^\circ\text{C} is physically plausible for solid copper, which melts at 1085∘C1085^\circ\text{C}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ΔL=w0=1.44 mm=1.44×10−3 m\Delta L = w_0 = 1.44\text{ mm} = 1.44 \times 10^{-3}\text{ m}

  2. ΔT=w0αL0=1.44×10−3 m(1.70×10−5 ∘C−1)(1.200 m)≈70.59∘C\Delta T = \frac{w_0}{\alpha L_0} = \frac{1.44 \times 10^{-3}\text{ m}}{(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(1.200\text{ m})} \approx 70.59^\circ\text{C}

  3. Tcontact=18.0∘C+70.59∘C≈88.6∘CT_{\text{contact}} = 18.0^\circ\text{C} + 70.59^\circ\text{C} \approx 88.6^\circ\text{C}

  4. Since Tf=115.0∘C>TcontactT_f = 115.0^\circ\text{C} > T_{\text{contact}}, the constrained temperature rise is ΔTconstrained=115.0∘C−88.59∘C=26.41∘C\Delta T_{\text{constrained}} = 115.0^\circ\text{C} - 88.59^\circ\text{C} = 26.41^\circ\text{C}

  5. σ=YαΔTconstrained=(1.10×1011 Pa)(1.70×10−5 ∘C−1)(26.41∘C)≈4.94×107 Pa\sigma = Y \alpha \Delta T_{\text{constrained}} = (1.10 \times 10^{11}\text{ Pa})(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(26.41^\circ\text{C}) \approx 4.94 \times 10^7\text{ Pa}

Final answer

(a) Tcontact=88.6∘CT_{\text{contact}} = 88.6^\circ\text{C}; (b) σ=4.94×107 Pa\sigma = 4.94 \times 10^7\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Form the habit of explicitly converting all millimeter (10−3 m10^{-3}\text{ m}) values to standard SI meters before entering numbers into your calculator.

  • Review thermal stress problems with gaps to practice partitioning the temperature change into an unconstrained free expansion phase and a constrained stress-building phase.

Lock it in

Similar question

01

An aluminum rod of length L0=0.800 mL_0 = 0.800\text{ m} (α=2.40×10−5 ∘C−1\alpha = 2.40 \times 10^{-5}\text{ }^\circ\text{C}^{-1}, Y=7.00×1010 PaY = 7.00 \times 10^{10}\text{ Pa}) has a gap of 0.480 mm0.480\text{ mm} to a fixed wall at 20.0∘C20.0^\circ\text{C}. Find the contact temperature TcontactT_{\text{contact}}.

Answer

Tcontact=45.0∘CT_{\text{contact}} = 45.0^\circ\text{C}. Elongation required is ΔL=0.480×10−3 m\Delta L = 0.480 \times 10^{-3}\text{ m}. Using ΔT=ΔLαL0=0.480×10−3(2.40×10−5)(0.800)=25.0∘C\Delta T = \frac{\Delta L}{\alpha L_0} = \frac{0.480 \times 10^{-3}}{(2.40 \times 10^{-5})(0.800)} = 25.0^\circ\text{C}, we get Tcontact=20.0∘C+25.0∘C=45.0∘CT_{\text{contact}} = 20.0^\circ\text{C} + 25.0^\circ\text{C} = 45.0^\circ\text{C}.

02

For the aluminum rod in the previous problem, if the temperature continues to rise from Tcontact=45.0∘CT_{\text{contact}} = 45.0^\circ\text{C} to Tf=95.0∘CT_f = 95.0^\circ\text{C}, calculate the compressive thermal stress inside the rod.

Answer

σ=8.40×107 Pa\sigma = 8.40 \times 10^7\text{ Pa}. The constrained temperature change is ΔTconstrained=95.0∘C−45.0∘C=50.0∘C\Delta T_{\text{constrained}} = 95.0^\circ\text{C} - 45.0^\circ\text{C} = 50.0^\circ\text{C}. The thermal stress is σ=YαΔTconstrained=(7.00×1010 Pa)(2.40×10−5 ∘C−1)(50.0∘C)=8.40×107 Pa\sigma = Y \alpha \Delta T_{\text{constrained}} = (7.00 \times 10^{10}\text{ Pa})(2.40 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(50.0^\circ\text{C}) = 8.40 \times 10^7\text{ Pa}.

03

A steel rail of length 20.0 m20.0\text{ m} (α=1.20×10−5 ∘C−1\alpha = 1.20 \times 10^{-5}\text{ }^\circ\text{C}^{-1}, Y=2.00×1011 PaY = 2.00 \times 10^{11}\text{ Pa}) is laid with an expansion gap of 3.60 mm3.60\text{ mm} at 15.0∘C15.0^\circ\text{C}. If the rail reaches a peak summer temperature of 55.0∘C55.0^\circ\text{C}, determine whether stress develops, and if so, calculate its magnitude.

Answer

σ=6.00×107 Pa\sigma = 6.00 \times 10^7\text{ Pa}. The temperature rise to close the gap is ΔT1=3.60×10−3 m(1.20×10−5 ∘C−1)(20.0 m)=15.0∘C\Delta T_1 = \frac{3.60 \times 10^{-3}\text{ m}}{(1.20 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(20.0\text{ m})} = 15.0^\circ\text{C}, giving Tcontact=30.0∘CT_{\text{contact}} = 30.0^\circ\text{C}. Since 55.0∘C>30.0∘C55.0^\circ\text{C} > 30.0^\circ\text{C}, compressive stress develops over ΔTconstrained=55.0∘C−30.0∘C=25.0∘C\Delta T_{\text{constrained}} = 55.0^\circ\text{C} - 30.0^\circ\text{C} = 25.0^\circ\text{C}. Thus, σ=YαΔT=(2.00×1011)(1.20×10−5)(25.0)=6.00×107 Pa\sigma = Y \alpha \Delta T = (2.00 \times 10^{11})(1.20 \times 10^{-5})(25.0) = 6.00 \times 10^7\text{ Pa}.

Loading workspace…