Resources

A heavy uniform cable of length L=20.0 mL = 20.0\text{ m} and total mass M=40.0 kgM = 40.0\text{ kg} hangs vertically from a high ceiling under its own weight. A tiny high-frequency transverse vibration is introduced at the bottom end and travels upward toward the ceiling. Because tension varies continuously with height yy (where y=0y = 0 is the free bottom end and y=Ly = L is the fixed top support), the local wave speed v(y)=gyv(y) = \sqrt{g y} approaches zero as y→0y \to 0. Derive the total travel time τ\tau for a wave pulse to propagate from the bottom to the top of the cable, and calculate this time using g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

Travel time formula: τ=2Lg\tau = 2\sqrt{\frac{L}{g}}; Numerical value: τ=2.86 s\tau = 2.86\text{ s}

Steps

01

Determine the Tension and Local Wave Speed

Let yy represent the vertical distance measured from the free bottom end of the cable (y=0y = 0) toward the fixed ceiling support (y=Ly = L).

The cable is uniform, so its linear mass density is: μ=ML\mu = \frac{M}{L}

At any height yy, the tension T(y)T(y) supports the weight of the portion of the cable hanging below it, which has mass m(y)=μym(y) = \mu y: T(y)=m(y)g=μgyT(y) = m(y)g = \mu g y

The speed of a transverse wave on a string or cable depends on the local tension and linear mass density: v(y)=T(y)μ=μgyμ=gyv(y) = \sqrt{\frac{T(y)}{\mu}} = \sqrt{\frac{\mu g y}{\mu}} = \sqrt{g y}

(Notice that the wave speed is completely independent of the cable's total mass MM, as mass cancels out.)


02

Set Up and Evaluate the Travel Time Integral

Wave speed is the instantaneous rate of change of position with respect to time: v(y)=dydt  ⟹  dt=dyv(y)v(y) = \frac{dy}{dt} \implies dt = \frac{dy}{v(y)}

Substitute v(y)=gyv(y) = \sqrt{gy}: dt=dygy=1gy−1/2dydt = \frac{dy}{\sqrt{gy}} = \frac{1}{\sqrt{g}} y^{-1/2} dy

To find the total travel time τ\tau as the pulse travels from the bottom (y=0y = 0) to the top (y=Ly = L), integrate both sides: τ=∫0Ldygy=1g∫0Ly−1/2dy\tau = \int_0^L \frac{dy}{\sqrt{gy}} = \frac{1}{\sqrt{g}} \int_0^L y^{-1/2} dy

Using the power rule for integration, ∫y−1/2dy=2y1/2\int y^{-1/2} dy = 2y^{1/2}: τ=1g[2y]0L=2Lg\tau = \frac{1}{\sqrt{g}} \Big[ 2\sqrt{y} \Big]_0^L = 2\sqrt{\frac{L}{g}}

Common Pitfall: Do not calculate travel time by simply dividing the length LL by the maximum speed v(L)v(L) or the simple arithmetic mean of speeds. Because speed varies with position as y\sqrt{y} rather than linearly with yy, an integral over yy is required.


03

Calculate the Numerical Value

Substitute the given values L=20.0 mL = 20.0\text{ m} and g=9.80 m/s2g = 9.80\text{ m/s}^2: τ=220.09.80=22.0408≈2×1.4286≈2.86 s\tau = 2\sqrt{\frac{20.0}{9.80}} = 2\sqrt{2.0408} \approx 2 \times 1.4286 \approx 2.86\text{ s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets the factor of 2 resulting from integrating y^(-1/2), getting τ = √(L/g) instead of 2√(L/g).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=dydt=gy  ⟹  dt=dygyv = \frac{dy}{dt} = \sqrt{gy} \implies dt = \frac{dy}{\sqrt{gy}}

  2. Step 2

    τ=∫(gy)−1/2 dy=yg  ⟹  τ=Lg\tau = \int (gy)^{-1/2}\,dy = \sqrt{\frac{y}{g}} \implies \tau = \sqrt{\frac{L}{g}}

    Correct

    τ=∫0Ldygy=1g[2y]0L=2Lg\tau = \int_0^L \frac{dy}{\sqrt{gy}} = \frac{1}{\sqrt{g}} \left[ 2\sqrt{y} \right]_0^L = 2\sqrt{\frac{L}{g}}

    When applying the power rule ∫yn dy=yn+1n+1\int y^n\,dy = \frac{y^{n+1}}{n+1} to n=−1/2n = -1/2, dividing by the new exponent gives y1/21/2=2y\frac{y^{1/2}}{1/2} = 2\sqrt{y}. You omitted the factor of 22 from dividing by 1/21/2.

  3. Step 3

    τ=20.09.80=1.43 s\tau = \sqrt{\frac{20.0}{9.80}} = 1.43\text{ s}

    Correct

    τ=220.09.80≈2.86 s\tau = 2\sqrt{\frac{20.0}{9.80}} \approx 2.86\text{ s}

    Your numerical evaluation correctly evaluated your derived formula, but the result is half the true value due to the missing factor of 22 in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that wave speed varies with height along the hanging cable.

You properly related the travel time differential to position via dt=dyv(y)dt = \frac{dy}{v(y)}.

You correctly substituted the numerical parameters into your symbolic formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Power rule integration with fractional exponent

You integrated y−1/2y^{-1/2} as y1/2y^{1/2} without dividing by the new power 1/21/2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting the exponent division when applying the power rule ∫xn dx=xn+1n+1\int x^n\,dx = \frac{x^{n+1}}{n+1} to a negative half fraction: dividing by 12\frac{1}{2} produces a multiplying factor of 22.

REASONING PATH
Your ACEpath teacher’s suggested approach
Fractional Power Rule
  • ∫y−1/2 dy=y−1/2+1−1/2+1=y1/21/2=2y\int y^{-1/2}\,dy = \frac{y^{-1/2 + 1}}{-1/2 + 1} = \frac{y^{1/2}}{1/2} = 2\sqrt{y}

  • Always explicitly write 1n+1\frac{1}{n+1} before simplifying fractional powers to ensure the coefficient is not dropped.

Constant Acceleration Analogy
  • Since v=gyv = \sqrt{gy}, we have v2=gyv^2 = gy, which means acceleration a=vdvdy=g2a = v\frac{dv}{dy} = \frac{g}{2} is constant. For constant acceleration from rest, L=12at2  ⟹  τ=2La=2Lg/2=2LgL = \frac{1}{2}at^2 \implies \tau = \sqrt{\frac{2L}{a}} = \sqrt{\frac{2L}{g/2}} = 2\sqrt{\frac{L}{g}}.

  • Use the kinematic average speed vˉ=vf2\bar{v} = \frac{v_f}{2} to check your result: τ=Lvˉ=L12gL=2Lg\tau = \frac{L}{\bar{v}} = \frac{L}{\frac{1}{2}\sqrt{gL}} = 2\sqrt{\frac{L}{g}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Evaluate the integral over the full length of the cable: τ=1g∫0Ly−1/2 dy\tau = \frac{1}{\sqrt{g}} \int_0^L y^{-1/2}\,dy.

  2. Apply the power rule correctly: ∫y−1/2 dy=y1/21/2=2y1/2\int y^{-1/2}\,dy = \frac{y^{1/2}}{1/2} = 2y^{1/2}.

  3. Evaluate at the boundaries 00 and LL: τ=1g[2L−0]=2Lg\tau = \frac{1}{\sqrt{g}} \left[ 2\sqrt{L} - 0 \right] = 2\sqrt{\frac{L}{g}}.

  4. Substitute the given numbers: τ=220.09.80=2×1.4286≈2.86 s\tau = 2\sqrt{\frac{20.0}{9.80}} = 2 \times 1.4286 \approx 2.86\text{ s}.

Final answer

τ=2Lg≈2.86 s\tau = 2\sqrt{\frac{L}{g}} \approx 2.86\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice integrating powers with negative and fractional exponents, explicitly showing the 1n+1\frac{1}{n+1} divisor.

  • Check variable-speed wave travel times using the average speed property whenever wave speed scales as y\sqrt{y}.

OverviewACEpath Teacher's Diagnosis

02 The student assumes a constant wave speed equal to the maximum speed at the top instead of integrating the varying speed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    vtop=gL  ⟹  vtop=14.0 m/sv_{\text{top}} = \sqrt{g L} \implies v_{\text{top}} = 14.0\text{ m/s}

  2. Step 2

    τ=Lvtop  ⟹  τ=20.014.0=1.43 s\tau = \frac{L}{v_{\text{top}}} \implies \tau = \frac{20.0}{14.0} = 1.43\text{ s}

    Correct

    τ=∫0Ldyv(y)=∫0Ldygy=2Lg≈2.86 s\tau = \int_0^L \frac{dy}{v(y)} = \int_0^L \frac{dy}{\sqrt{gy}} = 2\sqrt{\frac{L}{g}} \approx 2.86\text{ s}

    The formula Δt=Δyv\Delta t = \frac{\Delta y}{v} only applies when speed is constant. Here, v(y)=gyv(y) = \sqrt{gy} varies continuously from 00 at the bottom to 14.0 m/s14.0\text{ m/s} at the top, so you must integrate dt=dyv(y)dt = \frac{dy}{v(y)}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the maximum wave speed at the top of the cable.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Constant-speed assumption for variable-speed motion

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used the uniform-motion relation time = distance / speed with the maximum speed at the top, overlooking that the pulse accelerates with height and requires integration over position.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check for Position-Dependent Speed
  • When speed vv depends on position yy, travel time must be evaluated using dt=dyv(y)dt = \frac{dy}{v(y)} rather than dividing distance by an endpoint speed.

  • Always write down dt=dyv(y)dt = \frac{dy}{v(y)} and integrate over the path from the starting position to the ending position.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Relate infinitesimal time dtdt to vertical displacement dydy: dt=dyv(y)=dygydt = \frac{dy}{v(y)} = \frac{dy}{\sqrt{gy}}.

  2. Integrate from the bottom (y=0y = 0) to the top (y=Ly = L): τ=∫0Ldygy=1g∫0Ly−1/2 dy\tau = \int_0^L \frac{dy}{\sqrt{gy}} = \frac{1}{\sqrt{g}} \int_0^L y^{-1/2}\,dy.

  3. Evaluate the integral using the power rule: τ=1g[2y]0L=2Lg\tau = \frac{1}{\sqrt{g}} \left[ 2\sqrt{y} \right]_0^L = 2\sqrt{\frac{L}{g}}.

  4. Substitute L=20.0 mL = 20.0\text{ m} and g=9.80 m/s2g = 9.80\text{ m/s}^2: τ=220.09.80≈2.86 s\tau = 2\sqrt{\frac{20.0}{9.80}} \approx 2.86\text{ s}.

Final answer

τ=2Lg=2.86 s\tau = 2\sqrt{\frac{L}{g}} = 2.86\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how to set up time integrals for non-uniform wave propagation.

  • Practice distinguishing between time-averaged speed and position-averaged speed.

OverviewACEpath Teacher's Diagnosis

03 The student averages the bottom speed (0) and top speed to find an average speed, leading to τ = 2L/√(gL) = 2√(L/g) divided incorrectly by assuming v_avg = √(gL)/2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v(0)=0  ⟹  v(L)=gLv(0) = 0 \implies v(L) = \sqrt{g L}

  2. Step 2

    vavg=0+gL2=gL2v_{\text{avg}} = \frac{0 + \sqrt{g L}}{2} = \frac{\sqrt{g L}}{2}

    Correct

    dt=dyv(y)=dygydt = \frac{dy}{v(y)} = \frac{dy}{\sqrt{gy}}

    You assumed that the average speed over the journey is simply the arithmetic mean of the endpoint speeds. Because the speed depends nonlinearly on position (v∝yv \propto \sqrt{y}), you must integrate dt=dyv(y)dt = \frac{dy}{v(y)} along the cable rather than assuming vˉ=v1+v22\bar{v} = \frac{v_1 + v_2}{2} without proving constant acceleration in time.

  3. Step 3

    t=Lvavg=2LgL=2Lgt = \frac{L}{v_{\text{avg}}} = \frac{2 L}{\sqrt{g L}} = 2 \sqrt{\frac{L}{g}}

    Correct

    τ=∫0Ldygy=1g[2y]0L=2Lg\tau = \int_0^L \frac{dy}{\sqrt{gy}} = \frac{1}{\sqrt{g}} \left[ 2\sqrt{y} \right]_0^L = 2\sqrt{\frac{L}{g}}

    While this formula matches the correct travel time, it directly inherits the unproven average-speed assumption from the previous step rather than deriving the result via integration.

  4. Step 4

    vavg=9.80×20.02=7.0 m/s  ⟹  τ=20.07.0=2.86 sv_{\text{avg}} = \frac{\sqrt{9.80 \times 20.0}}{2} = 7.0\text{ m/s} \implies \tau = \frac{20.0}{7.0} = 2.86\text{ s}

    Correct

    τ=220.0 m9.80 m/s2≈2.86 s\tau = 2\sqrt{\frac{20.0\text{ m}}{9.80\text{ m/s}^2}} \approx 2.86\text{ s}

    You completed the arithmetic accurately, but the numerical answer rests on the ungrounded endpoint-averaging method.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the boundary conditions for wave speed at both ends of the cable.

You performed accurate algebraic simplification to express τ\tau in simplest radical form.

You calculated the final numerical value with correct arithmetic and appropriate precision.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unjustified Average Speed Assumption

You used the arithmetic mean formula vavg=v1+v22v_{\text{avg}} = \frac{v_1 + v_2}{2} to find travel time across a spatially varying velocity field.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

The formula vˉ=vi+vf2\bar{v} = \frac{v_i + v_f}{2} is only generally valid when acceleration with respect to time is constant (v(t)v(t) is linear in tt). When speed varies with position yy as v(y)=gyv(y) = \sqrt{gy}, the total travel time must be derived from first principles using calculus: τ=∫dyv(y)\tau = \int \frac{dy}{v(y)}. While it turns out that pulse acceleration is coincidentally constant here (a=g2a = \frac{g}{2}), stating vˉ=vi+vf2\bar{v} = \frac{v_i + v_f}{2} without demonstrating that constant acceleration holds is an incomplete derivation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Position vs. Time Dependence
  • When speed is given as a function of position v(x)v(x) rather than time v(t)v(t), travel time is an integral over space.

  • Write dt=dxv(x)dt = \frac{dx}{v(x)} and integrate both sides: Δt=∫x1x2dxv(x)\Delta t = \int_{x_1}^{x_2} \frac{dx}{v(x)}.

Validate Endpoint Averaging
  • The relation vavg=v1+v22v_{\text{avg}} = \frac{v_1 + v_2}{2} is only valid if a=dvdt=constanta = \frac{dv}{dt} = \text{constant}.

  • Check whether v(y)dvdyv(y) \frac{dv}{dy} is constant before using kinematic formulas intended for uniform acceleration.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the differential relationship between travel time and vertical displacement: dt=dyv(y)=dygy=1gy−1/2 dydt = \frac{dy}{v(y)} = \frac{dy}{\sqrt{gy}} = \frac{1}{\sqrt{g}} y^{-1/2}\,dy.

  2. Integrate from the bottom of the cable (y=0y = 0) to the top support (y=Ly = L): τ=1g∫0Ly−1/2 dy\tau = \frac{1}{\sqrt{g}} \int_0^L y^{-1/2}\,dy.

  3. Apply the power rule ∫y−1/2 dy=2y1/2\int y^{-1/2}\,dy = 2y^{1/2}: τ=1g[2y]0L=2Lg\tau = \frac{1}{\sqrt{g}} \left[ 2\sqrt{y} \right]_0^L = 2\sqrt{\frac{L}{g}}.

  4. Substitute L=20.0 mL = 20.0\text{ m} and g=9.80 m/s2g = 9.80\text{ m/s}^2: τ=220.09.80≈2.86 s\tau = 2\sqrt{\frac{20.0}{9.80}} \approx 2.86\text{ s}.

Final answer

τ=2Lg≈2.86 s\tau = 2\sqrt{\frac{L}{g}} \approx 2.86\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice deriving travel times for non-uniform media by setting up the integral τ=∫dxv(x)\tau = \int \frac{dx}{v(x)}.

  • Avoid using arithmetic means of endpoint speeds unless you have explicitly proven that acceleration with respect to time is constant.

Lock it in

Similar question

01

A uniform chain of length L=4.90 mL = 4.90\text{ m} hangs vertically from a ceiling. How long does a transverse pulse take to travel from the bottom end to the top support? (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

τ=2.00 s\tau = 2.00\text{ s}. Step: τ=2Lg=24.909.80=20.500≈2(0.707)=1.414 s\tau = 2\sqrt{\frac{L}{g}} = 2\sqrt{\frac{4.90}{9.80}} = 2\sqrt{0.500} \approx 2(0.707) = 1.414\text{ s} — wait, 20.5=2×0.7071=1.41 s2\sqrt{0.5} = 2 \times 0.7071 = 1.41\text{ s}.

02

A vertical hanging cable has a heavy mass attached at the bottom so that the tension is dominated by this mass: T(y)≈T0T(y) \approx T_0 (constant). How does the travel time τconst\tau_{\text{const}} to reach height LL compare to the travel time τfree=2L/g\tau_{\text{free}} = 2\sqrt{L/g} of a cable hanging under only its own weight, assuming both have the same speed v(L)=gLv(L) = \sqrt{gL} at the top?

Answer

τconst=12τfree=Lg\tau_{\text{const}} = \frac{1}{2}\tau_{\text{free}} = \sqrt{\frac{L}{g}}. When speed is constant at v(L)=gLv(L) = \sqrt{gL}, τ=Lv(L)=Lg\tau = \frac{L}{v(L)} = \sqrt{\frac{L}{g}}. The self-weighted rope takes exactly twice as long because its average speed is 12v(L)\frac{1}{2}v(L).

03

A flexible rope of length LL hangs from the ceiling. A pulse is launched upward from the bottom (y=0y = 0) at t=0t = 0. At what height yy along the rope has the pulse spent exactly half of its total transit time τ\tau?

Answer

y=L4y = \frac{L}{4}. Step: The elapsed time to reach height yy is t(y)=2ygt(y) = 2\sqrt{\frac{y}{g}}. Setting t(y)=12τ=12(2Lg)=Lgt(y) = \frac{1}{2}\tau = \frac{1}{2}\left(2\sqrt{\frac{L}{g}}\right) = \sqrt{\frac{L}{g}} gives 2yg=Lg  ⟹  y=12L  ⟹  y=L42\sqrt{\frac{y}{g}} = \sqrt{\frac{L}{g}} \implies \sqrt{y} = \frac{1}{2}\sqrt{L} \implies y = \frac{L}{4}.

Loading workspace…