Resources

A uniform cylindrical copper conductor of length L1=2.40 mL_1 = 2.40\text{ m} and circular cross-sectional radius r1=0.800 mmr_1 = 0.800\text{ mm} carries a steady current of I1=3.60 AI_1 = 3.60\text{ A} when connected across a potential difference of V1=0.0720 VV_1 = 0.0720\text{ V}. (a) Calculate the resistance R1R_1 of the initial conductor. (b) The wire is subsequently disconnected and mechanically drawn through a die so that its length is uniformly stretched by a factor of 3.003.00 to L2=3.00L1L_2 = 3.00 L_1 while maintaining constant total copper volume and uniform cross-section. Calculate the new resistance R2R_2 of the elongated wire. (c) If the newly drawn wire is connected to the exact same potential difference V2=V1=0.0720 VV_2 = V_1 = 0.0720\text{ V}, determine the resulting current I2I_2 in the circuit.

Answer and steps

Final answer

(a) R1=2.00×10−2 ΩR_1 = 2.00 \times 10^{-2}\ \Omega; (b) R2=0.180 ΩR_2 = 0.180\ \Omega; (c) I2=0.400 AI_2 = 0.400\text{ A}

Steps

Part (a): Initial Resistance of the Conductor

According to Ohm's law, the electrical resistance R1R_1 of a conductor across which a potential difference V1V_1 produces a current I1I_1 is given by:

R1=V1I1R_1 = \frac{V_1}{I_1}

Substitute the given values:

R1=0.0720 V3.60 A=0.0200 Ω=2.00×10−2 ΩR_1 = \frac{0.0720\text{ V}}{3.60\text{ A}} = 0.0200\ \Omega = 2.00 \times 10^{-2}\ \Omega


Part (b): Resistance After Elongation

When the wire is drawn through a die, its total volume V\mathcal{V} remains constant:

V=A1L1=A2L2\mathcal{V} = A_1 L_1 = A_2 L_2

Given that the length is stretched by a factor of 3.003.00 (L2=3.00L1L_2 = 3.00 L_1), the new cross-sectional area A2A_2 must decrease proportionally:

A2=A1⋅L1L2=A13.00A_2 = A_1 \cdot \frac{L_1}{L_2} = \frac{A_1}{3.00}

The resistance of a uniform conductor is defined as R=ρLAR = \rho \frac{L}{A}, where ρ\rho is the resistivity of copper. Expressing the new resistance R2R_2 in terms of the original dimensions:

R2=ρL2A2=ρ3.00L1A1/3.00=(3.00)2(ρL1A1)=9.00R1R_2 = \rho \frac{L_2}{A_2} = \rho \frac{3.00 L_1}{A_1 / 3.00} = (3.00)^2 \left(\rho \frac{L_1}{A_1}\right) = 9.00 R_1

Common Pitfall: A frequent mistake is assuming that only the length changes while the cross-sectional area remains unchanged. In a physical deformation such as drawing or stretching, the volume is conserved, so stretching the wire makes it narrower, causing resistance to scale with the square of the length change: R∝L2R \propto L^2.

Substitute the value of R1R_1:

R2=9.00×0.0200 Ω=0.180 ΩR_2 = 9.00 \times 0.0200\ \Omega = 0.180\ \Omega


Part (c): Resulting Current Under the Same Voltage

With the newly drawn wire connected to the same potential difference V2=V1=0.0720 VV_2 = V_1 = 0.0720\text{ V}, applying Ohm's law gives the new current I2I_2:

I2=V2R2I_2 = \frac{V_2}{R_2}

Substitute the values:

I2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}

(Alternatively, because VV is constant and resistance increased by a factor of 99, the current decreases by the same factor: I2=I19.00=3.60 A9.00=0.400 AI_2 = \frac{I_1}{9.00} = \frac{3.60\text{ A}}{9.00} = 0.400\text{ A}.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the reduction in cross-sectional area required by volume conservation and assumes resistance scales linearly with length.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R1=V1I1=0.07203.60=0.0200 ΩR_1 = \frac{V_1}{I_1} = \frac{0.0720}{3.60} = 0.0200\ \Omega

  2. Step 2

    R is proportional to length L  ⟹  R2=3.00⋅R1=3.00⋅0.0200=0.0600 ΩR\text{ is proportional to length }L \implies R_2 = 3.00 \cdot R_1 = 3.00 \cdot 0.0200 = 0.0600\ \Omega

    Correct

    Volume V=A1L1=A2L2  ⟹  A2=A13.00  ⟹  R2=ρL2A2=3.002R1=9.00R1=0.180 Ω\text{Volume }\mathcal{V} = A_1 L_1 = A_2 L_2 \implies A_2 = \frac{A_1}{3.00} \implies R_2 = \rho\frac{L_2}{A_2} = 3.00^2 R_1 = 9.00 R_1 = 0.180\ \Omega

    When a wire is drawn out, its volume remains constant. Stretching its length by a factor of 3.003.00 forces its cross-sectional area to shrink by a factor of 3.003.00, increasing the resistance by a factor of 3.002=9.003.00^2 = 9.00 rather than 3.003.00.

  3. Step 3

    I2=V2R2=0.07200.0600=1.20 AI_2 = \frac{V_2}{R_2} = \frac{0.0720}{0.0600} = 1.20\text{ A}

    Correct

    I2=V2R2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{V_2}{R_2} = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}

    Your formula and substitution method were completely sound, but your result was affected by the incorrect value of R2R_2 from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Ohm's law to determine the initial resistance of the wire.

You correctly identified that current equals voltage divided by resistance under the same potential difference.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglecting Volume Conservation in Wire Stretching

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that R∝LR \propto L holds during mechanical deformation, overlooking that the wire's cross-sectional area must decrease simultaneously because the total volume of metal is conserved (A2=A1/3.00A_2 = A_1 / 3.00).

REASONING PATH
Your ACEpath teacher’s suggested approach
Volume Conservation Rule
  • For a fixed mass of conductor, volume V=AL\mathcal{V} = A L is constant; thus, stretching by a factor of nn (L→nLL \to nL) causes the area to scale as A→A/nA \to A/n.

  • Always write R=ρLA=ρL2VR = \rho \frac{L}{A} = \rho \frac{L^2}{\mathcal{V}} when a wire is stretched or drawn, yielding R∝L2R \propto L^2.

Scaling Factor Check
  • If length increases by a factor of nn at constant volume, resistance increases by n2n^2, not nn.

  • Square the length stretching factor before multiplying by the original resistance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Account for constant volume: V=A1L1=A2L2  ⟹  A2=A13.00\mathcal{V} = A_1 L_1 = A_2 L_2 \implies A_2 = \frac{A_1}{3.00}.

  2. Apply the resistivity formula: R2=ρL2A2=ρ3.00L1A1/3.00=9.00(ρL1A1)=9.00R1=9.00×0.0200 Ω=0.180 ΩR_2 = \rho\frac{L_2}{A_2} = \rho\frac{3.00 L_1}{A_1 / 3.00} = 9.00\left(\rho\frac{L_1}{A_1}\right) = 9.00 R_1 = 9.00 \times 0.0200\ \Omega = 0.180\ \Omega.

  3. Calculate the new current using Ohm's law: I2=V2R2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{V_2}{R_2} = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}.

Final answer

(a) R1=2.00×10−2 ΩR_1 = 2.00 \times 10^{-2}\ \Omega; (b) R2=0.180 ΩR_2 = 0.180\ \Omega; (c) I2=0.400 AI_2 = 0.400\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • When solving deformation problems, always check whether material is being added or if an existing piece is simply being reshaped under constant volume.

  • Practice using the combined formula R=ρL2VR = \rho \frac{L^2}{\mathcal{V}} for wire-stretching questions to avoid forgetting the change in area.

OverviewACEpath Teacher's Diagnosis

02 The student assumes that the radius decreases by a factor of 3 rather than the cross-sectional area, causing an incorrect scaling factor of 27.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R1=V1I1=0.07203.60=0.0200 ΩR_1 = \frac{V_1}{I_1} = \frac{0.0720}{3.60} = 0.0200\ \Omega

  2. Step 2

    r2=r1/3.00  ⟹  A2=π⋅r22=π⋅(r13.00)2=A19.00r_2 = r_1 / 3.00 \implies A_2 = \pi \cdot r_2^2 = \pi \cdot \left(\frac{r_1}{3.00}\right)^2 = \frac{A_1}{9.00}

    Correct

    V=A1L1=A2L2  ⟹  A2=A1⋅L13.00L1=A13.00\mathcal{V} = A_1 L_1 = A_2 L_2 \implies A_2 = A_1 \cdot \frac{L_1}{3.00 L_1} = \frac{A_1}{3.00}

    Because the copper volume is conserved during drawing (V=A⋅L\mathcal{V} = A \cdot L), tripling the length scales the cross-sectional area AA by 13\frac{1}{3}, not the radius rr.

  3. Step 3

    R2=ρ⋅(3.00⋅L1)A1/9.00=27.0⋅R1  ⟹  R2=27.0⋅0.0200=0.540 ΩR_2 = \rho \cdot \frac{(3.00 \cdot L_1)}{A_1 / 9.00} = 27.0 \cdot R_1 \implies R_2 = 27.0 \cdot 0.0200 = 0.540\ \Omega

    Correct

    R2=ρ3.00L1A1/3.00=9.00R1=9.00×0.0200 Ω=0.180 ΩR_2 = \rho \frac{3.00 L_1}{A_1 / 3.00} = 9.00 R_1 = 9.00 \times 0.0200\ \Omega = 0.180\ \Omega

    Your algebraic handling of R=ρLAR = \rho \frac{L}{A} was consistent with your earlier value of A2A_2, but it inherited the incorrect area scaling factor.

  4. Step 4

    I2=V2R2=0.07200.540=0.133 AI_2 = \frac{V_2}{R_2} = \frac{0.0720}{0.540} = 0.133\text{ A}

    Correct

    I2=V2R2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{V_2}{R_2} = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}

    You correctly applied Ohm's law with the given voltage, but the resulting current is numerical downstream error from R2R_2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Ohm's law to compute the initial resistance R1R_1.

You recognized that lengthening the conductor reduces its cross-sectional area and increases its resistance.

You accurately substituted values into Ohm's law to find current in part (c).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Volume conservation vs. linear dimension scaling

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied the factor of 3 length increase directly to reduce the radius rr instead of the total cross-sectional area AA, overlooking that volume conservation relates length and area inversely via V=AL\mathcal{V} = A L.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conserve total volume first
  • For an object deformed at constant volume, V=A1L1=A2L2\mathcal{V} = A_1 L_1 = A_2 L_2.

  • Always find the ratio of areas directly using A2A1=L1L2\frac{A_2}{A_1} = \frac{L_1}{L_2} before thinking about radius.

Express resistance in terms of length alone
  • Since A=VLA = \frac{\mathcal{V}}{L}, resistance scales as R=ρLA=ρL2V∝L2R = \rho \frac{L}{A} = \rho \frac{L^2}{\mathcal{V}} \propto L^2.

  • When a wire is stretched uniformly without losing mass, scale resistance by the square of the length factor: R2=n2R1R_2 = n^2 R_1 when L2=nL1L_2 = n L_1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up volume conservation: A1L1=A2L2  ⟹  A2=A1(L13.00L1)=A13.00A_1 L_1 = A_2 L_2 \implies A_2 = A_1 \left(\frac{L_1}{3.00 L_1}\right) = \frac{A_1}{3.00}.

  2. Substitute into the resistance formula: R2=ρL2A2=ρ3.00L1A1/3.00=9.00(ρL1A1)=9.00R1R_2 = \rho \frac{L_2}{A_2} = \rho \frac{3.00 L_1}{A_1 / 3.00} = 9.00 \left(\rho \frac{L_1}{A_1}\right) = 9.00 R_1.

  3. Calculate R2R_2: R2=9.00×0.0200 Ω=0.180 ΩR_2 = 9.00 \times 0.0200\ \Omega = 0.180\ \Omega.

  4. Compute the new current: I2=V2R2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{V_2}{R_2} = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}.

Final answer

(a) R1=2.00×10−2 ΩR_1 = 2.00 \times 10^{-2}\ \Omega; (b) R2=0.180 ΩR_2 = 0.180\ \Omega; (c) I2=0.400 AI_2 = 0.400\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice using the shortcut R∝L2R \propto L^2 for constant-volume stretching problems.

  • Solve problems that specify a change in radius rather than length to compare how R∝1r4R \propto \frac{1}{r^4} applies under volume conservation.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly calculates the initial resistance by multiplying voltage and current instead of dividing.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    R1=V1⋅I1=0.0720⋅3.60=0.2592 ΩR_1 = V_1 \cdot I_1 = 0.0720 \cdot 3.60 = 0.2592\ \Omega

    Correct

    R1=V1I1=0.0720 V3.60 A=0.0200 Ω=2.00×10−2 ΩR_1 = \frac{V_1}{I_1} = \frac{0.0720\text{ V}}{3.60\text{ A}} = 0.0200\ \Omega = 2.00 \times 10^{-2}\ \Omega

    You multiplied potential difference by current instead of dividing. By Ohm's law, V=IRV = I R, which rearranges to R=VIR = \frac{V}{I}. The product V⋅IV \cdot I represents electrical power PP, not resistance.

  2. Step 2

    Volume is constant so A2=A13.00  ⟹  R2=3.002⋅R1=9.00⋅0.2592=2.333 Ω\text{Volume is constant so } A_2 = \frac{A_1}{3.00} \implies R_2 = 3.00^2 \cdot R_1 = 9.00 \cdot 0.2592 = 2.333\ \Omega

    Correct

    R2=9.00R1=9.00×0.0200 Ω=0.180 ΩR_2 = 9.00 R_1 = 9.00 \times 0.0200\ \Omega = 0.180\ \Omega

    Your reasoning that volume conservation requires A2=A1/3.00A_2 = A_1 / 3.00 and causes resistance to scale by 3.002=9.003.00^2 = 9.00 is completely correct. The numerical result is inaccurate only because it used the incorrect value of R1R_1 from step 1.

  3. Step 3

    I2=V2R2=0.07202.333=0.0309 AI_2 = \frac{V_2}{R_2} = \frac{0.0720}{2.333} = 0.0309\text{ A}

    Correct

    I2=V2R2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{V_2}{R_2} = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}

    You correctly set up Ohm's law as I2=V2R2I_2 = \frac{V_2}{R_2}, but the numerical value was affected by your previous value of R2R_2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that total volume remains constant when drawing the wire.

You recognized that tripling the length reduces the cross-sectional area by a factor of 3, scaling resistance by 32=93^2 = 9.

You applied Ohm's law in the correct quotient form I=VRI = \frac{V}{R} in part (c).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Rearrangement / Ohm's Law Inversion

You wrote R=V⋅IR = V \cdot I instead of R=VIR = \frac{V}{I} when calculating initial resistance.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the formula for electrical resistance (R=VIR = \frac{V}{I}) with the formula for electrical power (P=V⋅IP = V \cdot I), or inverted the algebraic rearrangement of V=IRV = I R.

REASONING PATH
Your ACEpath teacher’s suggested approach
Algebraic Rearrangement of Ohm's Law
  • Ohm's law relates voltage, current, and resistance by V=IRV = I R.

  • To isolate resistance RR, divide both sides by current: R=VIR = \frac{V}{I}.

Unit and Dimensional Verification
  • Volts times amperes yields watts (power): 1 V×1 A=1 W1\text{ V} \times 1\text{ A} = 1\text{ W}. Volts divided by amperes yields ohms: 1 V/1 A=1 Ω1\text{ V} / 1\text{ A} = 1\ \Omega.

  • Always verify that your formula produces ohms (V/A\text{V}/\text{A}) rather than watts (V⋅A\text{V}\cdot\text{A}) before proceeding.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate R1R_1: R1=V1I1=0.0720 V3.60 A=0.0200 Ω=2.00×10−2 ΩR_1 = \frac{V_1}{I_1} = \frac{0.0720\text{ V}}{3.60\text{ A}} = 0.0200\ \Omega = 2.00 \times 10^{-2}\ \Omega.

  2. Apply your valid scaling factor of 9.009.00: R2=9.00R1=9.00×0.0200 Ω=0.180 ΩR_2 = 9.00 R_1 = 9.00 \times 0.0200\ \Omega = 0.180\ \Omega.

  3. Calculate the new current I2I_2: I2=V2R2=0.0720 V0.180 Ω=0.400 AI_2 = \frac{V_2}{R_2} = \frac{0.0720\text{ V}}{0.180\ \Omega} = 0.400\text{ A}.

Final answer

(a) R1=2.00×10−2 ΩR_1 = 2.00 \times 10^{-2}\ \Omega; (b) R2=0.180 ΩR_2 = 0.180\ \Omega; (c) I2=0.400 AI_2 = 0.400\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three standard arrangements of Ohm's law: V=IRV = IR, I=VRI = \frac{V}{R}, and R=VIR = \frac{V}{I}.

  • Use dimensional analysis to catch formula mix-ups: recall that V⋅IV \cdot I gives power in watts, not resistance in ohms.

  • Practice solving coupled conductor deformation problems where length and area vary together.

Lock it in

Similar question

01

A cylindrical aluminum wire has an initial resistance of 0.50 Ω0.50\ \Omega. It is drawn through a machine so that its length increases by 50%50\% (to 1.501.50 times its original length) while maintaining constant total volume. Calculate its new resistance.

Answer

R2=1.13 ΩR_2 = 1.13\ \Omega. Key steps: Volume conservation gives A2=A1/1.50A_2 = A_1 / 1.50. Thus, R2=R1(L2/L1)2=(1.50)2R1=2.25×0.50 Ω=1.125 Ω≈1.13 ΩR_2 = R_1 (L_2/L_1)^2 = (1.50)^2 R_1 = 2.25 \times 0.50\ \Omega = 1.125\ \Omega \approx 1.13\ \Omega.

02

A copper rod of resistance RR is drawn out uniformly so that its diameter is halved (d2=d1/2d_2 = d_1 / 2). Assuming the total copper volume is conserved, express the new resistance R′R' in terms of RR.

Answer

R′=16RR' = 16R. Key steps: Cross-sectional area scales with diameter squared, so A2=A1/4A_2 = A_1 / 4. By volume conservation (A1L1=A2L2A_1 L_1 = A_2 L_2), length quadruples (L2=4L1L_2 = 4L_1). Therefore, R′=ρL2A2=ρ4L1A1/4=16(ρL1A1)=16RR' = \rho \frac{L_2}{A_2} = \rho \frac{4L_1}{A_1 / 4} = 16 \left(\rho \frac{L_1}{A_1}\right) = 16R.

03

A heating element with resistance R0=12.0 ΩR_0 = 12.0\ \Omega operates at a steady voltage V=120 VV = 120\text{ V}. The wire is mechanically re-drawn so that its length is stretched to 2.002.00 times its original length at constant volume, and it is then connected across the same 120 V120\text{ V} supply. Determine the new power dissipation PP compared to the initial power P0P_0.

Answer

P=300 WP = 300\text{ W} (which is P0/4P_0 / 4). Key steps: Stretching by a factor of 22 at constant volume increases resistance by 22=42^2 = 4, so R=4R0=48.0 ΩR = 4 R_0 = 48.0\ \Omega. Initial power is P0=V2/R0=1202/12=1200 WP_0 = V^2 / R_0 = 120^2 / 12 = 1200\text{ W}. The new power is P=V2/R=1202/48=300 WP = V^2 / R = 120^2 / 48 = 300\text{ W}, exactly one-fourth of the original.

Loading workspace…