Resources

A mining cart of mass m=650 kgm = 650\text{ kg} travels along an underground railway. A coordinate system is established where the tunnel entrance is defined as the reference datum y=0 my = 0\text{ m}. The cart rolls down into a lower drift located at y=−45.0 my = -45.0\text{ m} relative to the entrance. (a) Calculate the gravitational potential energy UgU_g of the cart at the bottom of the drift relative to the entrance datum. (b) If the cart was traveling at v1=4.00 m/sv_1 = 4.00\text{ m/s} at the entrance (y=0 my = 0\text{ m}) and reaches the drift (y=−45.0 my = -45.0\text{ m}) with a speed of v2=28.0 m/sv_2 = 28.0\text{ m/s}, calculate the change in kinetic energy ΔK=K2−K1\Delta K = K_2 - K_1 and verify whether the change in mechanical energy ΔE=ΔK+ΔUg\Delta E = \Delta K + \Delta U_g is consistent with energy conservation. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

(a) Ug=−2.87×105 JU_g = -2.87 \times 10^5\text{ J}; (b) ΔK=2.50×105 J\Delta K = 2.50 \times 10^5\text{ J}, ΔE=−3.70×104 J\Delta E = -3.70 \times 10^4\text{ J} (indicating a loss of 3.70×104 J3.70 \times 10^4\text{ J} of mechanical energy to non-conservative friction forces).

Steps

01

Change in Kinetic Energy (ΔK\Delta K)

Part (a): Gravitational Potential Energy at the Drift

Gravitational potential energy UgU_g is determined relative to a chosen reference level (datum) where y=0 my = 0\text{ m}: Ug=mgyU_g = m g y Given:

  • Mass of the cart, m=650 kgm = 650\text{ kg}
  • Acceleration due to gravity, g=9.80 m/s2g = 9.80\text{ m/s}^2
  • Vertical position at the drift, y=−45.0 my = -45.0\text{ m} Substitute the given values: Ug=(650 kg)(9.80 m/s2)(−45.0 m)=−286,650 JU_g = (650\text{ kg})(9.80\text{ m/s}^2)(-45.0\text{ m}) = -286{,}650\text{ J} Expressed to three significant figures: Ug=−2.87×105 JU_g = -2.87 \times 10^5\text{ J} (Note: The negative sign indicates that the cart is located below the chosen reference height.)

Part (b): Change in Kinetic Energy and Mechanical Energy Balance

The kinetic energy of an object of mass mm moving at speed vv is given by K=12mv2K = \frac{1}{2}mv^2. The change in kinetic energy is:

ΔK=K2−K1=12m(v22−v12)\Delta K = K_2 - K_1 = \frac{1}{2}m\left(v_2^2 - v_1^2\right)

Substitute the initial speed v1=4.00 m/sv_1 = 4.00\text{ m/s} and final speed v2=28.0 m/sv_2 = 28.0\text{ m/s}:

v22−v12=(28.0)2−(4.00)2=784−16.0=768 m2/s2v_2^2 - v_1^2 = (28.0)^2 - (4.00)^2 = 784 - 16.0 = 768\text{ m}^2/\text{s}^2

ΔK=12(650 kg)(768 m2/s2)=249,600 J≈2.50×105 J\Delta K = \frac{1}{2}(650\text{ kg})(768\text{ m}^2/\text{s}^2) = 249{,}600\text{ J} \approx 2.50 \times 10^5\text{ J}

02

Change in Gravitational Potential Energy (ΔUg\Delta U_g)

At the entrance datum (y1=0 my_1 = 0\text{ m}), U1=0 JU_1 = 0\text{ J}. Therefore:

ΔUg=U2−U1=−286,650 J−0 J=−286,650 J\Delta U_g = U_2 - U_1 = -286{,}650\text{ J} - 0\text{ J} = -286{,}650\text{ J}

03

Total Change in Mechanical Energy (ΔE\Delta E)

The total change in mechanical energy is the sum of the changes in kinetic and potential energy:

ΔE=ΔK+ΔUg\Delta E = \Delta K + \Delta U_g

ΔE=249,600 J+(−286,650 J)=−37,050 J≈−3.70×104 J\Delta E = 249{,}600\text{ J} + (-286{,}650\text{ J}) = -37{,}050\text{ J} \approx -3.70 \times 10^4\text{ J}

04

Physical Interpretation

If only conservative forces (gravity) were acting, the total mechanical energy would be conserved (ΔE=0\Delta E = 0). Here, ΔE=−3.70×104 J<0\Delta E = -3.70 \times 10^4\text{ J} < 0, which means mechanical energy decreased. This indicates that non-conservative resistive forces, such as friction along the rails and air resistance, did negative work on the cart, dissipating 3.70×104 J3.70 \times 10^4\text{ J} of mechanical energy as thermal energy.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student treats vertical position as a positive distance rather than a negative coordinate below the datum, yielding a positive potential energy and an incorrect mechanical energy sum of 536250 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ug=m⋅g⋅h⟹Ug=650⋅9.80⋅45.0⟹Ug=286650 JU_g = m \cdot g \cdot h \Longrightarrow U_g = 650 \cdot 9.80 \cdot 45.0 \Longrightarrow U_g = 286650\text{ J}

    Correct

    Ug=mgy=(650 kg)(9.80 m/s2)(−45.0 m)=−2.87×105 JU_g = mgy = (650\text{ kg})(9.80\text{ m/s}^2)(-45.0\text{ m}) = -2.87 \times 10^5\text{ J}

    You substituted the height as a positive value +45.0 m+45.0\text{ m}. Because the drift lies below the reference datum (y=0 my = 0\text{ m}), its vertical coordinate is y=−45.0 my = -45.0\text{ m}, giving a negative potential energy of −286650 J-286650\text{ J} (or −2.87×105 J-2.87 \times 10^5\text{ J}).

  2. Step 2

    K1=0.5⋅650⋅(4.00)2=5200 J⟹K2=0.5⋅650⋅(28.0)2=254800 J⟹ΔK=254800−5200=249600 JK_1 = 0.5 \cdot 650 \cdot (4.00)^2 = 5200\text{ J} \Longrightarrow K_2 = 0.5 \cdot 650 \cdot (28.0)^2 = 254800\text{ J} \Longrightarrow \Delta K = 254800 - 5200 = 249600\text{ J}

  3. Step 3

    ΔE=ΔK+ΔUg=249600+286650=536250 J⟹Mechanical energy is not conserved because ΔE≠0.\Delta E = \Delta K + \Delta U_g = 249600 + 286650 = 536250\text{ J} \Longrightarrow \text{Mechanical energy is not conserved because } \Delta E \neq 0.

    Correct

    ΔE=ΔK+ΔUg=249600 J+(−286650 J)=−3.70×104 J\Delta E = \Delta K + \Delta U_g = 249600\text{ J} + (-286650\text{ J}) = -3.70 \times 10^4\text{ J}

    Your formula ΔE=ΔK+ΔUg\Delta E = \Delta K + \Delta U_g is correct, but carrying forward the positive potential energy value resulted in ΔE=+536250 J\Delta E = +536250\text{ J} instead of −3.70×104 J-3.70 \times 10^4\text{ J}. A negative ΔE\Delta E indicates that mechanical energy was lost to non-conservative friction forces.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the initial kinetic energy K1K_1 and final kinetic energy K2K_2.

You accurately found the net change in kinetic energy ΔK=249600 J\Delta K = 249600\text{ J}.

You correctly identified the mechanical energy relation ΔE=ΔK+ΔUg\Delta E = \Delta K + \Delta U_g and recognized that ΔE≠0\Delta E \neq 0 implies non-conservation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in potential energy coordinate

No, this is a conceptual error regarding how gravitational potential energy depends on position relative to a chosen datum.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used vertical distance as an absolute positive quantity hh rather than a signed position coordinate yy relative to the datum y=0 my = 0\text{ m}. Points below the reference level must have negative coordinates, leading to negative potential energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Reference Datum
  • In Ug=mgyU_g = mgy, yy is the vertical position coordinate relative to the chosen reference level y=0 my = 0\text{ m}, not scalar distance.

  • Check whether the location is above (y>0y > 0) or below (y<0y < 0) the reference plane before substituting.

Physical Sanity Check on Energy Changes
  • When an object rolls downward, gravity does positive work and gravitational potential energy must decrease (ΔUg<0\Delta U_g < 0).

  • Verify that moving to a lower elevation yields a negative change in potential energy.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the vertical coordinate of the drift below the datum: y=−45.0 my = -45.0\text{ m}.

  2. Calculate the gravitational potential energy: Ug=mgy=(650)(9.80)(−45.0)=−286650 J≈−2.87×105 JU_g = mgy = (650)(9.80)(-45.0) = -286650\text{ J} \approx -2.87 \times 10^5\text{ J}.

  3. Calculate the change in potential energy from entrance (y1=0 my_1 = 0\text{ m}, U1=0 JU_1 = 0\text{ J}): ΔUg=−286650 J−0 J=−286650 J\Delta U_g = -286650\text{ J} - 0\text{ J} = -286650\text{ J}.

  4. Sum the energy changes: ΔE=ΔK+ΔUg=249600 J+(−286650 J)=−37050 J≈−3.70×104 J\Delta E = \Delta K + \Delta U_g = 249600\text{ J} + (-286650\text{ J}) = -37050\text{ J} \approx -3.70 \times 10^4\text{ J}.

Final answer

(a) Ug=−2.87×105 JU_g = -2.87 \times 10^5\text{ J}; (b) ΔK=2.50×105 J\Delta K = 2.50 \times 10^5\text{ J}, ΔE=−3.70×104 J\Delta E = -3.70 \times 10^4\text{ J} (mechanical energy decreased due to work done by friction).

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the coordinate definition yy alongside the datum y=0 my = 0\text{ m} before calculating potential energy.

  • Perform a direction check: moving downward must always result in ΔUg<0\Delta U_g < 0.

  • Practice calculating mechanical energy changes in systems involving subterranean or underwater coordinates.

OverviewACEpath Teacher's Diagnosis

02 The student calculates change in kinetic energy by squaring the difference in speeds rather than taking the difference of squared speeds, leading to ΔK = 187200 J and ΔE = -99450 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ug=m⋅g⋅y⟹Ug=650⋅9.80⋅(−45.0)⟹Ug=−286650 JU_g = m \cdot g \cdot y \Longrightarrow U_g = 650 \cdot 9.80 \cdot (-45.0) \Longrightarrow U_g = -286650\text{ J}

  2. Step 2

    Δv=28.0−4.00=24.0 m/s⟹ΔK=0.5⋅m⋅(Δv)2=0.5⋅650⋅(24.0)2⟹ΔK=187200 J\Delta v = 28.0 - 4.00 = 24.0\text{ m/s} \Longrightarrow \Delta K = 0.5 \cdot m \cdot (\Delta v)^2 = 0.5 \cdot 650 \cdot (24.0)^2 \Longrightarrow \Delta K = 187200\text{ J}

    Correct

    ΔK=12m(v22−v12)=12(650 kg)[(28.0 m/s)2−(4.00 m/s)2]=249600 J\Delta K = \frac{1}{2}m(v_2^2 - v_1^2) = \frac{1}{2}(650\text{ kg})[(28.0\text{ m/s})^2 - (4.00\text{ m/s})^2] = 249600\text{ J}

    You calculated ΔK\Delta K as 12m(Δv)2\frac{1}{2}m(\Delta v)^2, but kinetic energy is quadratic in velocity. The change in kinetic energy must be computed as K2−K1=12m(v22−v12)K_2 - K_1 = \frac{1}{2}m(v_2^2 - v_1^2).

  3. Step 3

    ΔE=ΔK+ΔUg=187200+(−286650)=−99450 J\Delta E = \Delta K + \Delta U_g = 187200 + (-286650) = -99450\text{ J}

    Correct

    ΔE=ΔK+ΔUg=249600 J+(−286650 J)=−37050 J≈−3.70×104 J\Delta E = \Delta K + \Delta U_g = 249600\text{ J} + (-286650\text{ J}) = -37050\text{ J} \approx -3.70 \times 10^4\text{ J}

    Your formula for total mechanical energy change is conceptually correct, but the numerical result is affected by the incorrect value of ΔK\Delta K from the previous step.

  4. Step 4

    Mechanical energy is not conserved because ΔE≠0.\text{Mechanical energy is not conserved because } \Delta E \neq 0.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and calculated the gravitational potential energy at a negative vertical elevation.

You recognized that the total change in mechanical energy is given by ΔE=ΔK+ΔUg\Delta E = \Delta K + \Delta U_g.

You correctly concluded that mechanical energy is not conserved when ΔE≠0\Delta E \neq 0.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic & Conceptual Error in Kinetic Energy Change

Calculating ΔK\Delta K using (Δv)2(\Delta v)^2 rather than v22−v12v_2^2 - v_1^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the difference of squares with the square of a difference when applying the kinetic energy formula. Because K∝v2K \propto v^2, ΔK=K2−K1=12m(v22−v12)≠12m(v2−v1)2\Delta K = K_2 - K_1 = \frac{1}{2}m(v_2^2 - v_1^2) \neq \frac{1}{2}m(v_2 - v_1)^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Expanding Kinetic Energy Change
  • ΔK=K2−K1=12mv22−12mv12=12m(v22−v12)\Delta K = K_2 - K_1 = \frac{1}{2}m v_2^2 - \frac{1}{2}m v_1^2 = \frac{1}{2}m(v_2^2 - v_1^2)

  • Always evaluate each speed squared first, subtract them, and then multiply by 12m\frac{1}{2}m. Never square the change in speed (Δv)(\Delta v).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ΔK=12m(v22−v12)=12(650 kg)[(28.0)2−(4.00)2] J=0.5×650×(784−16.0)=249600 J≈2.50×105 J\Delta K = \frac{1}{2}m(v_2^2 - v_1^2) = \frac{1}{2}(650\text{ kg})[(28.0)^2 - (4.00)^2]\text{ J} = 0.5 \times 650 \times (784 - 16.0) = 249600\text{ J} \approx 2.50 \times 10^5\text{ J}

  2. ΔE=ΔK+ΔUg=249600 J+(−286650 J)=−37050 J≈−3.70×104 J\Delta E = \Delta K + \Delta U_g = 249600\text{ J} + (-286650\text{ J}) = -37050\text{ J} \approx -3.70 \times 10^4\text{ J}

Final answer

(a) Ug=−2.87×105 JU_g = -2.87 \times 10^5\text{ J}; (b) ΔK=2.50×105 J\Delta K = 2.50 \times 10^5\text{ J}, ΔE=−3.70×104 J\Delta E = -3.70 \times 10^4\text{ J} (mechanical energy is not conserved; 3.70×104 J3.70 \times 10^4\text{ J} is lost to non-conservative forces such as friction).

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the algebraic identity (a−b)2=a2−2ab+b2≠a2−b2(a - b)^2 = a^2 - 2ab + b^2 \neq a^2 - b^2 to see why squaring before subtracting changes the result.

  • Practice computing ΔK\Delta K by explicitly writing out K2K_2 and K1K_1 as separate quantities before subtracting them.

OverviewACEpath Teacher's Diagnosis

03 The student reverses the order of subtraction when computing the change in kinetic energy as initial minus final, resulting in ΔK = -249600 J and ΔE = -536250 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ug=m⋅g⋅y⟹Ug=650⋅9.80⋅(−45.0)⟹Ug=−286650 JU_g = m \cdot g \cdot y \Longrightarrow U_g = 650 \cdot 9.80 \cdot (-45.0) \Longrightarrow U_g = -286650\text{ J}

  2. Step 2

    K1=0.5⋅650⋅(4.00)2=5200 J⟹K2=0.5⋅650⋅(28.0)2=254800 JK_1 = 0.5 \cdot 650 \cdot (4.00)^2 = 5200\text{ J} \Longrightarrow K_2 = 0.5 \cdot 650 \cdot (28.0)^2 = 254800\text{ J}

  3. Step 3

    ΔK=K1−K2=5200−254800=−249600 J\Delta K = K_1 - K_2 = 5200 - 254800 = -249600\text{ J}

    Correct

    ΔK=K2−K1=254800 J−5200 J=249600 J≈2.50×105 J\Delta K = K_2 - K_1 = 254800\text{ J} - 5200\text{ J} = 249600\text{ J} \approx 2.50 \times 10^5\text{ J}

    The change in any quantity ΔX\Delta X is defined as final minus initial (X2−X1X_2 - X_1). Since the cart sped up from 4.00 m/s4.00\text{ m/s} to 28.0 m/s28.0\text{ m/s}, its kinetic energy increased, meaning ΔK\Delta K must be positive.

  4. Step 4

    ΔE=ΔK+ΔUg=−249600+(−286650)=−536250 J⟹Mechanical energy is not conserved because ΔE≠0.\Delta E = \Delta K + \Delta U_g = -249600 + (-286650) = -536250\text{ J} \Longrightarrow \text{Mechanical energy is not conserved because } \Delta E \neq 0.

    Correct

    ΔE=ΔK+ΔUg=249600 J+(−286650 J)=−37050 J≈−3.70×104 J\Delta E = \Delta K + \Delta U_g = 249600\text{ J} + (-286650\text{ J}) = -37050\text{ J} \approx -3.70 \times 10^4\text{ J}

    Because ΔK\Delta K had the incorrect sign, your calculated total mechanical energy change ΔE\Delta E was incorrect, though your qualitative conclusion that mechanical energy was not conserved was correct.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the negative coordinate y=−45.0 my = -45.0\text{ m} to evaluate UgU_g.

You accurately computed the initial and final kinetic energy values from the given speeds.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Reversed delta order (initial minus final)

You set up ΔK\Delta K as K1−K2K_1 - K_2 instead of K2−K1K_2 - K_1.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the standard physical convention for change (ΔX=Xfinal−Xinitial\Delta X = X_\text{final} - X_\text{initial}) with a difference of initial minus final.

REASONING PATH
Your ACEpath teacher’s suggested approach
Standard Delta Definition
  • For any quantity XX, the change is always ΔX=Xfinal−Xinitial\Delta X = X_\text{final} - X_\text{initial}.

  • Check whether the object gained or lost the quantity: if it gained speed, ΔK\Delta K must be positive.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the standard definition of change: ΔK=K2−K1=254800 J−5200 J=+249600 J\Delta K = K_2 - K_1 = 254800\text{ J} - 5200\text{ J} = +249600\text{ J}.

  2. Sum the kinetic and potential energy changes: ΔE=ΔK+ΔUg=249600 J+(−286650 J)=−37050 J\Delta E = \Delta K + \Delta U_g = 249600\text{ J} + (-286650\text{ J}) = -37050\text{ J}.

  3. Round to three significant figures: ΔE≈−3.70×104 J\Delta E \approx -3.70 \times 10^4\text{ J}.

Final answer

(a) Ug=−2.87×105 JU_g = -2.87 \times 10^5\text{ J}; (b) ΔK=2.50×105 J\Delta K = 2.50 \times 10^5\text{ J}, ΔE=−3.70×104 J\Delta E = -3.70 \times 10^4\text{ J} (indicating a dissipation of 3.70×104 J3.70 \times 10^4\text{ J} of mechanical energy).

NEXT STEPS
Final Takeaways from Your Teacher
  • Whenever you write Δ\Delta, write final−initial\text{final} - \text{initial} above it as a reminder.

  • Perform a sanity check on signs: speeding up means positive ΔK\Delta K, falling down means negative ΔUg\Delta U_g.

Lock it in

Similar question

01

A 500 kg500\text{ kg} elevator car is at a basement level 12.0 m12.0\text{ m} below the street-level datum (y=0 my = 0\text{ m}). Calculate its gravitational potential energy relative to the street level. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Ug=mgy=(500 kg)(9.80 m/s2)(−12.0 m)=−5.88×104 JU_g = mgy = (500\text{ kg})(9.80\text{ m/s}^2)(-12.0\text{ m}) = -5.88 \times 10^4\text{ J}.

02

A 1200 kg1200\text{ kg} roller coaster car starts from rest at the top of a hill of height h=30.0 mh = 30.0\text{ m} above the track's lowest point (chosen as datum y=0 my = 0\text{ m}). It reaches the lowest point with a speed of 20.0 m/s20.0\text{ m/s}. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate ΔK\Delta K, ΔUg\Delta U_g, and the mechanical energy lost to friction ΔE\Delta E.

Answer

Initial state: y1=30.0 my_1 = 30.0\text{ m}, v1=0 m/sv_1 = 0\text{ m/s}. Final state: y2=0 my_2 = 0\text{ m}, v2=20.0 m/sv_2 = 20.0\text{ m/s}. ΔK=12(1200)(20.02−0)=2.40×105 J\Delta K = \frac{1}{2}(1200)(20.0^2 - 0) = 2.40 \times 10^5\text{ J}. ΔUg=mgy2−mgy1=0−(1200)(9.80)(30.0)=−3.528×105 J\Delta U_g = mgy_2 - mgy_1 = 0 - (1200)(9.80)(30.0) = -3.528 \times 10^5\text{ J}. ΔE=ΔK+ΔUg=2.40×105 J−3.528×105 J=−1.13×105 J\Delta E = \Delta K + \Delta U_g = 2.40 \times 10^5\text{ J} - 3.528 \times 10^5\text{ J} = -1.13 \times 10^5\text{ J} (a loss of 1.13×105 J1.13 \times 10^5\text{ J}).

03

A diver of mass 70.0 kg70.0\text{ kg} steps off a cliff into the ocean. Taking sea level as y=0 my = 0\text{ m}, the cliff edge is at y1=+15.0 my_1 = +15.0\text{ m}, and the diver comes momentarily to rest underwater at y2=−4.00 my_2 = -4.00\text{ m}. (a) Find the total change in gravitational potential energy ΔUg=U2−U1\Delta U_g = U_2 - U_1. (b) What is the total work done by non-conservative forces (water drag) on the diver during the entire fall? Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

(a) ΔUg=mg(y2−y1)=(70.0)(9.80)(−4.00−15.0)=(70.0)(9.80)(−19.0)=−1.30×104 J\Delta U_g = mg(y_2 - y_1) = (70.0)(9.80)(-4.00 - 15.0) = (70.0)(9.80)(-19.0) = -1.30 \times 10^4\text{ J}. (b) Since K1=0K_1 = 0 and K2=0K_2 = 0, ΔK=0\Delta K = 0. By the work-energy theorem, Wnc=ΔE=ΔK+ΔUg=−1.30×104 JW_{\text{nc}} = \Delta E = \Delta K + \Delta U_g = -1.30 \times 10^4\text{ J}.

Loading workspace…