Resources

In a university physics laboratory experiment, a student mounts a spring projectile launcher horizontally on the edge of a level lab bench of height h=1.225 mh = 1.225\text{ m} above the floor. The launcher propels a steel ball through a dual photogate timer with sensor gates spaced d=10.0 cmd = 10.0\text{ cm} apart. The digital timer measures an elapsed passage time of Δt=25.0 ms\Delta t = 25.0\text{ ms} between the two gates. The ball then flies off the bench and strikes carbon paper on the floor. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2: (a) calculate the horizontal launch speed v0v_0 measured by the photogate timer, (b) calculate the predicted theoretical horizontal range RtheoR_{\text{theo}}, and (c) if the measured experimental landing mark is Rexp=1.94 mR_{\text{exp}} = 1.94\text{ m}, calculate the percent error between the theoretical prediction and the measured experimental range.

Answer and steps

Final answer

(a) v0=4.00 m/sv_0 = 4.00\text{ m/s}; (b) Rtheo=2.00 mR_{\text{theo}} = 2.00\text{ m}; (c) Percent Error=3.00%\text{Percent Error} = 3.00\%

Steps

Part (a): Horizontal Launch Speed

The launcher propels the ball horizontally through two photogate sensors spaced at distance dd. Since the launcher is horizontal and the photogates are located immediately at the exit, the initial horizontal velocity v0v_0 is constant over this small distance:

v0=dΔtv_0 = \frac{d}{\Delta t}

Convert the measurements to standard SI units:

  • Distance: d=10.0 cm=0.100 md = 10.0\text{ cm} = 0.100\text{ m}
  • Time interval: Δt=25.0 ms=0.0250 s\Delta t = 25.0\text{ ms} = 0.0250\text{ s}

Substitute these values into the velocity equation:

v0=0.100 m0.0250 s=4.00 m/sv_0 = \frac{0.100\text{ m}}{0.0250\text{ s}} = 4.00\text{ m/s}


Part (b): Theoretical Horizontal Range

In projectile motion, horizontal and vertical motions are independent:

  1. Vertical Motion (Free Fall):
    The ball launches purely horizontally, so its initial vertical velocity is v0y=0v_{0y} = 0. Under a constant downward gravitational acceleration g=9.80 m/s2g = 9.80\text{ m/s}^2, the vertical displacement hh relates to the time of flight tt by:

    h=12gt2h = \frac{1}{2}gt^2

    Solving for the time of flight tt:

    t=2hg=2(1.225 m)9.80 m/s2=2.459.80=0.250 s=0.500 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2(1.225\text{ m})}{9.80\text{ m/s}^2}} = \sqrt{\frac{2.45}{9.80}} = \sqrt{0.250}\text{ s} = 0.500\text{ s}

  2. Horizontal Motion (Constant Velocity):
    Neglecting air resistance, horizontal velocity remains constant throughout the flight (ax=0a_x = 0). The theoretical horizontal range RtheoR_{\text{theo}} is:

    Rtheo=v0⋅t=(4.00 m/s)(0.500 s)=2.00 mR_{\text{theo}} = v_0 \cdot t = (4.00\text{ m/s})(0.500\text{ s}) = 2.00\text{ m}


Part (c): Percent Error

The percent error compares the measured experimental value (Rexp=1.94 mR_{\text{exp}} = 1.94\text{ m}) to the accepted theoretical value (Rtheo=2.00 mR_{\text{theo}} = 2.00\text{ m}):

Percent Error=∣Rtheo−Rexp∣Rtheo×100%\text{Percent Error} = \frac{|R_{\text{theo}} - R_{\text{exp}}|}{R_{\text{theo}}} \times 100\%

Substitute the values:

Percent Error=∣2.00 m−1.94 m∣2.00 m×100%=0.06 m2.00 m×100%=3.00%\text{Percent Error} = \frac{|2.00\text{ m} - 1.94\text{ m}|}{2.00\text{ m}} \times 100\% = \frac{0.06\text{ m}}{2.00\text{ m}} \times 100\% = 3.00\%

Common Pitfall: Dividing by the experimental value instead of the theoretical reference value will lead to an incorrect percent error calculation. Always use the theoretical value in the denominator.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the photogate distance and elapsed time to standard SI units, calculating the launch speed directly from centimeters and milliseconds.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v0=dΔt=10.025.0=0.400 m/sv_0 = \frac{d}{\Delta t} = \frac{10.0}{25.0} = 0.400\text{ m/s}

    Correct

    v0=dΔt=0.100 m0.0250 s=4.00 m/sv_0 = \frac{d}{\Delta t} = \frac{0.100\text{ m}}{0.0250\text{ s}} = 4.00\text{ m/s}

    You divided d=10.0 cmd = 10.0\text{ cm} by Δt=25.0 ms\Delta t = 25.0\text{ ms} without converting them into standard SI units (meters and seconds). The quotient 10.025.0=0.400 cm/ms\frac{10.0}{25.0} = 0.400\text{ cm/ms}, which equals 4.00 m/s4.00\text{ m/s}, not 0.400 m/s0.400\text{ m/s}.

  2. Step 2

    t=2hg=2⋅1.2259.80=0.250=0.500 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \cdot 1.225}{9.80}} = \sqrt{0.250} = 0.500\text{ s}

  3. Step 3

    Rtheo=v0⋅t=0.400⋅0.500=0.200 mR_{\text{theo}} = v_0 \cdot t = 0.400 \cdot 0.500 = 0.200\text{ m}

    Correct

    Rtheo=v0⋅t=(4.00 m/s)(0.500 s)=2.00 mR_{\text{theo}} = v_0 \cdot t = (4.00\text{ m/s})(0.500\text{ s}) = 2.00\text{ m}

    Your range formula Rtheo=v0tR_{\text{theo}} = v_0 t is correct, but your result is off by a factor of 10 because it inherited the incorrect value of v0v_0 from step 1.

  4. Step 4

    Percent Error=(1.94−0.2000.200)⋅100%=870%\text{Percent Error} = \left(\frac{1.94 - 0.200}{0.200}\right) \cdot 100\% = 870\%

    Correct

    Percent Error=∣Rtheo−Rexp∣Rtheo×100%=∣2.00 m−1.94 m∣2.00 m×100%=3.00%\text{Percent Error} = \frac{|R_{\text{theo}} - R_{\text{exp}}|}{R_{\text{theo}}} \times 100\% = \frac{|2.00\text{ m} - 1.94\text{ m}|}{2.00\text{ m}} \times 100\% = 3.00\%

    Your percent error calculation is numerically affected by using Rtheo=0.200 mR_{\text{theo}} = 0.200\text{ m}. Using the correct theoretical value of 2.00 m2.00\text{ m} yields a percent error of 3.00%3.00\%.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the horizontal launch velocity is given by the distance between photogates divided by the transit time.

You correctly derived and solved the vertical free-fall equation to obtain the flight time of t=0.500 st = 0.500\text{ s}.

You correctly applied the horizontal range equation Rtheo=v0tR_{\text{theo}} = v_0 t and the percent error formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You substituted the raw numbers 10.010.0 and 25.025.0 into the velocity formula without converting centimeters to meters and milliseconds to seconds.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Failing to convert laboratory sensor measurements from non-standard metric prefixes (centimeters and milliseconds) into base SI units (meters and seconds) before performing kinematic calculations.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert Sensor Readings to Base SI Units
  • Before substituting measured values into physics formulas that use g=9.80 m/s2g = 9.80\text{ m/s}^2, convert all lengths to meters (m\text{m}) and times to seconds (s\text{s}).

  • Write down explicit unit conversions first: 10.0 cm=10.0×10−2 m=0.100 m10.0\text{ cm} = 10.0 \times 10^{-2}\text{ m} = 0.100\text{ m} and 25.0 ms=25.0×10−3 s=0.0250 s25.0\text{ ms} = 25.0 \times 10^{-3}\text{ s} = 0.0250\text{ s}.

Sanity-Check Experimental Percent Error
  • In standard university lab experiments, a percent error exceeding 100%100\% (such as 870%870\%) almost always indicates an order-of-magnitude unit conversion mistake rather than experimental scatter.

  • When your theoretical prediction deviates drastically from the experimental measurement, re-verify your base units and initial velocity.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the photogate distance to meters: d=10.0 cm=0.100 md = 10.0\text{ cm} = 0.100\text{ m}.

  2. Convert the gate time to seconds: Δt=25.0 ms=0.0250 s\Delta t = 25.0\text{ ms} = 0.0250\text{ s}.

  3. Compute launch speed: v0=0.100 m0.0250 s=4.00 m/sv_0 = \frac{0.100\text{ m}}{0.0250\text{ s}} = 4.00\text{ m/s}.

  4. Calculate theoretical range: Rtheo=v0t=(4.00 m/s)(0.500 s)=2.00 mR_{\text{theo}} = v_0 t = (4.00\text{ m/s})(0.500\text{ s}) = 2.00\text{ m}.

  5. Calculate percent error: Percent Error=∣2.00 m−1.94 m∣2.00 m×100%=3.00%\text{Percent Error} = \frac{|2.00\text{ m} - 1.94\text{ m}|}{2.00\text{ m}} \times 100\% = 3.00\%.

Final answer

(a) v0=4.00 m/sv_0 = 4.00\text{ m/s}; (b) Rtheo=2.00 mR_{\text{theo}} = 2.00\text{ m}; (c) Percent Error=3.00%\text{Percent Error} = 3.00\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice explicitly writing the unit next to every numerical quantity in your substitution step.

  • Review common metric prefix conversions: 1 cm=10−2 m1\text{ cm} = 10^{-2}\text{ m} and 1 ms=10−3 s1\text{ ms} = 10^{-3}\text{ s}.

  • Perform order-of-magnitude reality checks on your calculated values before proceeding to downstream steps.

OverviewACEpath Teacher's Diagnosis

02 The student omits the factor of 2 in the kinematic equation for free-fall time, finding t = √(h/g) instead of √(2h/g).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v0=0.100 m0.0250 s=4.00 m/sv_0 = \frac{0.100\text{ m}}{0.0250\text{ s}} = 4.00\text{ m/s}

  2. Step 2

    t=hg=1.2259.80=0.125=0.354 st = \sqrt{\frac{h}{g}} = \sqrt{\frac{1.225}{9.80}} = \sqrt{0.125} = 0.354\text{ s}

    Correct

    t=2hg=2(1.225 m)9.80 m/s2=0.500 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2(1.225\text{ m})}{9.80\text{ m/s}^2}} = 0.500\text{ s}

    The vertical displacement formula for an object released from rest is h=12gt2h = \frac{1}{2}gt^2. Multiplying both sides by 22 before taking the square root gives t=2hgt = \sqrt{\frac{2h}{g}}, rather than hg\sqrt{\frac{h}{g}}.

  3. Step 3

    Rtheo=v0⋅t=4.00⋅0.354=1.416 mR_{\text{theo}} = v_0 \cdot t = 4.00 \cdot 0.354 = 1.416\text{ m}

    Correct

    Rtheo=v0⋅t=(4.00 m/s)(0.500 s)=2.00 mR_{\text{theo}} = v_0 \cdot t = (4.00\text{ m/s})(0.500\text{ s}) = 2.00\text{ m}

    Your formula for horizontal range is correct, but your numerical result was affected by the underestimated time of flight from the previous step.

  4. Step 4

    Percent Error=∣1.94−1.416∣1.416⋅100%=0.5241.416⋅100%=37.0%\text{Percent Error} = \frac{|1.94 - 1.416|}{1.416} \cdot 100\% = \frac{0.524}{1.416} \cdot 100\% = 37.0\%

    Correct

    Percent Error=∣Rtheo−Rexp∣Rtheo×100%=∣2.00 m−1.94 m∣2.00 m×100%=3.00%\text{Percent Error} = \frac{|R_{\text{theo}} - R_{\text{exp}}|}{R_{\text{theo}}} \times 100\% = \frac{|2.00\text{ m} - 1.94\text{ m}|}{2.00\text{ m}} \times 100\% = 3.00\%

    You set up the percent error expression correctly, but the value is incorrect because it used the inaccurate theoretical range of 1.416 m1.416\text{ m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted centimeters and milliseconds into standard SI units.

You used the correct horizontal kinematics relation R=v0tR = v_0 t.

You correctly structured the percent error formula using the theoretical value in the denominator.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Factor of 2 in Free-Fall Kinematic Formula

You forgot to multiply the height by 22 when inverting h=12gt2h = \frac{1}{2}gt^2 to solve for tt.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting h=12gt2h = \frac{1}{2}gt^2 requires multiplying both sides by 22 to clear the 12\frac{1}{2} coefficient before taking the square root, yielding t=2hgt = \sqrt{\frac{2h}{g}}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinematic Inversion Check
  • For motion from rest under constant acceleration, y=12at2  ⟹  t=2yay = \frac{1}{2}at^2 \implies t = \sqrt{\frac{2y}{a}}.

  • Always isolate t2t^2 completely by multiplying by 22 before taking the square root.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Solve for the vertical free-fall time: t=2hg=2(1.225 m)9.80 m/s2=0.250 s=0.500 st = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2(1.225\text{ m})}{9.80\text{ m/s}^2}} = \sqrt{0.250}\text{ s} = 0.500\text{ s}.

  2. Calculate theoretical horizontal range: Rtheo=v0⋅t=(4.00 m/s)(0.500 s)=2.00 mR_{\text{theo}} = v_0 \cdot t = (4.00\text{ m/s})(0.500\text{ s}) = 2.00\text{ m}.

  3. Compute percent error against the experimental measurement: Percent Error=∣2.00 m−1.94 m∣2.00 m×100%=0.06 m2.00 m×100%=3.00%\text{Percent Error} = \frac{|2.00\text{ m} - 1.94\text{ m}|}{2.00\text{ m}} \times 100\% = \frac{0.06\text{ m}}{2.00\text{ m}} \times 100\% = 3.00\%.

Final answer

(a) v0=4.00 m/sv_0 = 4.00\text{ m/s}; (b) Rtheo=2.00 mR_{\text{theo}} = 2.00\text{ m}; (c) Percent Error=3.00%\text{Percent Error} = 3.00\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out the full base kinematic equation Δy=v0yt+12ayt2\Delta y = v_{0y}t + \frac{1}{2}a_y t^2 before isolating variables.

  • Perform a quick mental unit and order-of-magnitude check on free-fall times: falling ≈1.2 m\approx 1.2\text{ m} takes half a second (0.5 s0.5\text{ s}), since h=12(9.8)(0.5)2≈1.225 mh = \frac{1}{2}(9.8)(0.5)^2 \approx 1.225\text{ m}.

OverviewACEpath Teacher's Diagnosis

03 The student uses the experimental measurement instead of the theoretical reference value in the denominator when calculating percent error.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v0=0.100 m0.0250 s=4.00 m/sv_0 = \frac{0.100\text{ m}}{0.0250\text{ s}} = 4.00\text{ m/s}

  2. Step 2

    t=2hg=2⋅1.2259.80=0.500 s  ⟹  Rtheo=v0⋅t=4.00⋅0.500=2.00 mt = \sqrt{\frac{2h}{g}} = \sqrt{\frac{2 \cdot 1.225}{9.80}} = 0.500\text{ s} \implies R_{\text{theo}} = v_0 \cdot t = 4.00 \cdot 0.500 = 2.00\text{ m}

  3. Step 3

    Percent Error=(Rexp−Rtheo)Rexp⋅100%=(∣1.94−2.00∣1.94)⋅100%=3.09%\text{Percent Error} = \frac{(R_{\text{exp}} - R_{\text{theo}})}{R_{\text{exp}}} \cdot 100\% = \left(\frac{|1.94 - 2.00|}{1.94}\right) \cdot 100\% = 3.09\%

    Correct

    Percent Error=∣Rtheo−Rexp∣Rtheo×100%=∣2.00−1.94∣2.00×100%=3.00%\text{Percent Error} = \frac{|R_{\text{theo}} - R_{\text{exp}}|}{R_{\text{theo}}} \times 100\% = \frac{|2.00 - 1.94|}{2.00} \times 100\% = 3.00\%

    Percent error measures how much an experimental measurement deviates relative to the accepted theoretical value, so the theoretical value Rtheo=2.00 mR_{\text{theo}} = 2.00\text{ m} must be in the denominator, not Rexp=1.94 mR_{\text{exp}} = 1.94\text{ m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted centimeters and milliseconds into standard SI units.

You accurately calculated the horizontal velocity from the photogate data.

You correctly separated horizontal and vertical kinematics to compute the theoretical range.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Denominator Selection in Percent Error

You divided the discrepancy by the experimental value (1.94 m1.94\text{ m}) instead of the theoretical reference value (2.00 m2.00\text{ m}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating percent error with percent difference or forgetting that percent error benchmarks an observed measurement against an established theoretical baseline.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Baseline Reference
  • Percent Error=∣Theoretical−Experimental∣Theoretical×100%\text{Percent Error} = \frac{|\text{Theoretical} - \text{Experimental}|}{\text{Theoretical}} \times 100\%

  • Always verify whether the benchmark is an accepted or theoretical value. Place that accepted reference value in the denominator.

Distinguish Percent Error from Percent Difference
  • Percent error compares an experimental measurement to an accepted standard (denominator is standard). Percent difference compares two experimental measurements with no accepted standard (denominator is their average).

  • Ask yourself: 'Is there a theoretical value derived from physical laws?' If yes, use it as the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the percent error definition: Percent Error=∣Rtheo−Rexp∣Rtheo×100%\text{Percent Error} = \frac{|R_{\text{theo}} - R_{\text{exp}}|}{R_{\text{theo}}} \times 100\%

  2. Substitute the values: Percent Error=∣2.00 m−1.94 m∣2.00 m×100%\text{Percent Error} = \frac{|2.00\text{ m} - 1.94\text{ m}|}{2.00\text{ m}} \times 100\%

  3. Evaluate the fraction: 0.06 m2.00 m×100%=0.0300×100%=3.00%\frac{0.06\text{ m}}{2.00\text{ m}} \times 100\% = 0.0300 \times 100\% = 3.00\%

Final answer

(a) v0=4.00 m/sv_0 = 4.00\text{ m/s}; (b) Rtheo=2.00 mR_{\text{theo}} = 2.00\text{ m}; (c) Percent Error=3.00%\text{Percent Error} = 3.00\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the rule that theoretical or accepted values serve as the standard of comparison in the denominator of percent error calculations.

  • Practice distinguishing between percent error (theoretical denominator) and percent difference (average denominator).

  • Solve follow-up problems comparing theoretical predictions with experimental data.

Lock it in

Similar question

01

A photogate timer with gates spaced d=8.0 cmd = 8.0\text{ cm} apart records an elapsed time of Δt=20.0 ms\Delta t = 20.0\text{ ms} for a glider on an air track. Calculate the speed of the glider in SI units (m/s\text{m/s}).

Answer

v=4.0 m/sv = 4.0\text{ m/s}. Convert units first: d=0.080 md = 0.080\text{ m}, Δt=0.0200 s\Delta t = 0.0200\text{ s}. Then v=0.080 m0.0200 s=4.0 m/sv = \frac{0.080\text{ m}}{0.0200\text{ s}} = 4.0\text{ m/s}.

02

A projectile is launched horizontally from a table of height h=0.80 mh = 0.80\text{ m}. A photogate measures its horizontal speed using a gate spacing of d=12.0 cmd = 12.0\text{ cm} and an elapsed time of Δt=40.0 ms\Delta t = 40.0\text{ ms}. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, find (a) the launch speed v0v_0 and (b) the theoretical landing range RtheoR_{\text{theo}}.

Answer

(a) v0=3.00 m/sv_0 = 3.00\text{ m/s}; (b) Rtheo≈1.21 mR_{\text{theo}} \approx 1.21\text{ m}. Step 1: v0=0.120 m0.0400 s=3.00 m/sv_0 = \frac{0.120\text{ m}}{0.0400\text{ s}} = 3.00\text{ m/s}. Step 2: t=2(0.80)9.80≈0.404 st = \sqrt{\frac{2(0.80)}{9.80}} \approx 0.404\text{ s}. Step 3: Rtheo=v0t=(3.00)(0.404)≈1.21 mR_{\text{theo}} = v_0 t = (3.00)(0.404) \approx 1.21\text{ m}.

03

In a horizontal projectile lab from height h=1.00 mh = 1.00\text{ m}, a student measures d=15.0 cmd = 15.0\text{ cm} and Δt=50.0 ms\Delta t = 50.0\text{ ms}. The projectile lands at a measured distance Rexp=1.40 mR_{\text{exp}} = 1.40\text{ m}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate (a) the theoretical range RtheoR_{\text{theo}} and (b) the percent error relative to the theoretical range.

Answer

(a) Rtheo=1.36 mR_{\text{theo}} = 1.36\text{ m}; (b) Percent Error=2.94%\text{Percent Error} = 2.94\%. Step 1: v0=0.150 m0.0500 s=3.00 m/sv_0 = \frac{0.150\text{ m}}{0.0500\text{ s}} = 3.00\text{ m/s}. Step 2: t=2(1.00)9.80≈0.4518 st = \sqrt{\frac{2(1.00)}{9.80}} \approx 0.4518\text{ s}. Step 3: Rtheo=3.00×0.4518≈1.355 m≈1.36 mR_{\text{theo}} = 3.00 \times 0.4518 \approx 1.355\text{ m} \approx 1.36\text{ m}. Step 4: Percent Error=∣1.355−1.40∣1.355×100%≈2.94%\text{Percent Error} = \frac{|1.355 - 1.40|}{1.355} \times 100\% \approx 2.94\%.

Loading workspace…