Resources

A wooden packing box of mass m=25.0 kgm = 25.0\text{ kg} is pulled at a constant velocity along a flat, level surface by a rope inclined at an angle θ\theta above the horizontal. The tension in the rope is T=85.0 NT = 85.0\text{ N}, and the coefficient of kinetic friction between the box and the floor is μk=0.300\mu_k = 0.300. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the pulling angle θ\theta (in degrees) relative to the horizontal, and calculate the corresponding magnitude of the kinetic frictional force fkf_k.

Answer and steps

Final answer

θ=23.3∘\theta = 23.3^\circ; the kinetic frictional force is fk=63.4 Nf_k = 63.4\text{ N}.

Steps

01

Identify the Forces Acting on the Box

A box of mass m=25.0 kgm = 25.0\text{ kg} is moving at a constant velocity along a flat, level surface. Because the velocity is constant, the acceleration is zero (a⃗=0\vec{a} = 0), meaning the net force in both the horizontal and vertical directions must be zero:

  • Weight (WW): Acts straight downward: W=mg=(25.0 kg)(9.80 m/s2)=245 NW = mg = (25.0\text{ kg})(9.80\text{ m/s}^2) = 245\text{ N}
  • Normal Force (NN): Exerted upward by the floor on the box.
  • Tension (TT): The rope pulls with a force of T=85.0 NT = 85.0\text{ N} at an angle θ\theta above the horizontal. Resolving this force into components gives: Tx=Tcos⁡θT_x = T \cos\theta Ty=Tsin⁡θT_y = T \sin\theta
  • Kinetic Friction (fkf_k): Opposes the forward motion and acts horizontally backward along the surface: fk=μkNf_k = \mu_k N

02

Apply Newton's First Law (Equilibrium Conditions)

Vertical Direction:

The box remains in contact with the level surface and does not accelerate vertically (∑Fy=0\sum F_y = 0): N+Tsin⁡θ−mg=0N + T \sin\theta - mg = 0 N=mg−Tsin⁡θN = mg - T \sin\theta

Key Pitfall: A common mistake is to assume N=mgN = mg. Because the rope pulls upward at an angle, its vertical component Tsin⁡θT\sin\theta partially supports the box's weight, thereby reducing the normal force exerted by the ground.

Horizontal Direction:

Since the box moves with constant velocity, the horizontal forces balance (∑Fx=0\sum F_x = 0): Tcos⁡θ−fk=0  ⟹  fk=Tcos⁡θT \cos\theta - f_k = 0 \implies f_k = T \cos\theta


03

Determine the Pulling Angle θ\theta

Substitute the expression for the normal force into the friction formula: fk=μk(mg−Tsin⁡θ)f_k = \mu_k (mg - T \sin\theta)

Equating the two expressions for fkf_k: Tcos⁡θ=μk(mg−Tsin⁡θ)T \cos\theta = \mu_k (mg - T \sin\theta)

Rearranging terms to group the angle θ\theta: Tcos⁡θ+μkTsin⁡θ=μkmgT \cos\theta + \mu_k T \sin\theta = \mu_k mg

Dividing both sides by TT: cos⁡θ+μksin⁡θ=μkmgT\cos\theta + \mu_k \sin\theta = \frac{\mu_k mg}{T}

Substitute the given numerical values: cos⁡θ+0.300sin⁡θ=0.300×245 N85.0 N=73.585.0≈0.865\cos\theta + 0.300 \sin\theta = \frac{0.300 \times 245\text{ N}}{85.0\text{ N}} = \frac{73.5}{85.0} \approx 0.865

Solving this trigonometric relationship for the pulling angle yields: θ=23.3∘\theta = 23.3^\circ


04

Calculate the Kinetic Frictional Force fkf_k

With θ=23.3∘\theta = 23.3^\circ, calculate the vertical component of the tension: Ty=Tsin⁡(23.3∘)=(85.0 N)sin⁡(23.3∘)≈(85.0 N)(0.3955)≈33.62 NT_y = T \sin(23.3^\circ) = (85.0\text{ N})\sin(23.3^\circ) \approx (85.0\text{ N})(0.3955) \approx 33.62\text{ N}

Next, find the normal force: N=mg−Tsin⁡θ=245 N−33.62 N=211.38 NN = mg - T \sin\theta = 245\text{ N} - 33.62\text{ N} = 211.38\text{ N}

Finally, compute the kinetic frictional force: fk=μkN=0.300×211.38 N≈63.4 Nf_k = \mu_k N = 0.300 \times 211.38\text{ N} \approx 63.4\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the vertical component of the rope tension when determining the normal force, setting N = m g.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg=25.0×9.80=245 NN = mg = 25.0 \times 9.80 = 245\text{ N}

    Correct

    ∑Fy=N+Tsin⁡θ−mg=0  ⟹  N=mg−Tsin⁡θ\sum F_y = N + T \sin\theta - mg = 0 \implies N = mg - T \sin\theta

    You set the normal force equal to the gravitational force alone. Because the rope pulls upward at an angle θ\theta, its vertical component Tsin⁡θT \sin\theta helps support the box's weight, reducing NN.

  2. Step 2

    Tcos⁡θ=fk=μkN  ⟹  85.0cos⁡θ=0.300×245=73.5  ⟹  cos⁡θ=73.585.0≈0.8647  ⟹  θ=arccos⁡(0.8647)≈30.2∘T \cos\theta = f_k = \mu_k N \implies 85.0 \cos\theta = 0.300 \times 245 = 73.5 \implies \cos\theta = \frac{73.5}{85.0} \approx 0.8647 \implies \theta = \arccos(0.8647) \approx 30.2^\circ

    Correct

    Tcos⁡θ=μk(mg−Tsin⁡θ)  ⟹  cos⁡θ+0.300sin⁡θ=0.300×24585.0≈0.8647  ⟹  θ≈23.3∘T \cos\theta = \mu_k (mg - T \sin\theta) \implies \cos\theta + 0.300 \sin\theta = \frac{0.300 \times 245}{85.0} \approx 0.8647 \implies \theta \approx 23.3^\circ

    Your horizontal equilibrium equation and algebraic execution were clean, but substituting N=245 NN = 245\text{ N} instead of mg−Tsin⁡θmg - T \sin\theta left out the sin⁡θ\sin\theta term from the balance equation.

  3. Step 3

    fk=μkN=0.300×245=73.5 Nf_k = \mu_k N = 0.300 \times 245 = 73.5\text{ N}

    Correct

    fk=μk(mg−Tsin⁡θ)=0.300×(245−85.0sin⁡(23.3∘))≈63.4 Nf_k = \mu_k (mg - T \sin\theta) = 0.300 \times (245 - 85.0 \sin(23.3^\circ)) \approx 63.4\text{ N}

    This calculation followed directly from your unadjusted normal force, leading to an overestimate of the kinetic frictional force.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that constant velocity implies zero net acceleration in both directions.

You correctly set the horizontal pulling force equal to kinetic friction, Tcos⁡θ=fkT \cos\theta = f_k.

You correctly recalled and applied the kinetic friction formula fk=μkNf_k = \mu_k N.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglected force component in normal force

Assuming N=mgN = mg on a level surface without accounting for the vertical component of the applied tension.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating normal force as an automatic intrinsic quantity equal to weight (mgmg) rather than determining it dynamically from vertical equilibrium (∑Fy=0\sum F_y = 0).

REASONING PATH
Your ACEpath teacher’s suggested approach
Set Up Vertical Equilibrium
  • On a level surface, ∑Fy=N+Fy,up−mg=0\sum F_y = N + F_{y,\text{up}} - mg = 0.

  • Always draw a free-body diagram and list every force with a vertical component before solving for NN.

Coupled Equations in Friction Problems
  • When an applied force is angled, it appears in both ∑Fx=0\sum F_x = 0 (via cosine) and ∑Fy=0\sum F_y = 0 (via sine).

  • Express N=mg−Tsin⁡θN = mg - T \sin\theta and substitute the entire binomial into fk=μkNf_k = \mu_k N.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up horizontal equilibrium: Tcos⁡θ=μkN=μk(mg−Tsin⁡θ)T \cos\theta = \mu_k N = \mu_k (mg - T \sin\theta).

  2. Rearrange to gather θ\theta terms: Tcos⁡θ+μkTsin⁡θ=μkmgT \cos\theta + \mu_k T \sin\theta = \mu_k mg.

  3. Divide by TT: cos⁡θ+0.300sin⁡θ=0.300×24585.0≈0.8647\cos\theta + 0.300 \sin\theta = \frac{0.300 \times 245}{85.0} \approx 0.8647.

  4. Solve the trigonometric equation: θ≈23.3∘\theta \approx 23.3^\circ.

  5. Compute the true normal force: N=245−85.0sin⁡(23.3∘)≈211.4 NN = 245 - 85.0 \sin(23.3^\circ) \approx 211.4\text{ N}.

  6. Calculate kinetic friction: fk=0.300×211.4 N≈63.4 Nf_k = 0.300 \times 211.4\text{ N} \approx 63.4\text{ N}.

Final answer

θ=23.3∘\theta = 23.3^\circ, fk=63.4 Nf_k = 63.4\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a complete free-body diagram whenever an applied force is inclined, explicitly resolving it into TxT_x and TyT_y.

  • Write out ∑Fy=may=0\sum F_y = m a_y = 0 as a formal first step rather than writing N=mgN = mg by default.

  • Practice solving linear combinations of sine and cosine using the harmonic identity Rcos⁡(θ−ϕ)R \cos(\theta - \phi) or numerical substitution.

OverviewACEpath Teacher's Diagnosis

02 The student swaps the sine and cosine components of the tension force in the equilibrium equations.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg−Tcos⁡θ=245−85.0cos⁡θN = mg - T\cos\theta = 245 - 85.0\cos\theta

    Correct

    N=mg−Tsin⁡θ=245−85.0sin⁡θN = mg - T\sin\theta = 245 - 85.0\sin\theta

    Because the rope is inclined at an angle θ\theta above the horizontal, the vertical component that assists in supporting the weight is Ty=Tsin⁡θT_y = T\sin\theta, not Tcos⁡θT\cos\theta.

  2. Step 2

    Tsin⁡θ=μkN=0.300(245−85.0cos⁡θ)T\sin\theta = \mu_k N = 0.300(245 - 85.0\cos\theta)

    Correct

    Tcos⁡θ=μkN=0.300(245−85.0sin⁡θ)T\cos\theta = \mu_k N = 0.300(245 - 85.0\sin\theta)

    The horizontal pulling force opposing friction along the flat ground is the adjacent component Tx=Tcos⁡θT_x = T\cos\theta, not Tsin⁡θT\sin\theta.

  3. Step 3

    sin⁡θ+0.300cos⁡θ=0.8647  ⟹  1.044sin⁡(θ+16.7∘)=0.8647  ⟹  θ=39.2∘\sin\theta + 0.300\cos\theta = 0.8647 \implies 1.044\sin(\theta + 16.7^\circ) = 0.8647 \implies \theta = 39.2^\circ

    Correct

    cos⁡θ+0.300sin⁡θ=0.8647  ⟹  1.044cos⁡(θ−16.7∘)=0.8647  ⟹  θ=23.3∘\cos\theta + 0.300\sin\theta = 0.8647 \implies 1.044\cos(\theta - 16.7^\circ) = 0.8647 \implies \theta = 23.3^\circ

    Your harmonic addition method was mathematically sound, but it operated on the swapped trigonometric coefficients from the earlier steps.

  4. Step 4

    fk=Tsin⁡θ=85.0sin⁡(39.2∘)=53.7 Nf_k = T\sin\theta = 85.0\sin(39.2^\circ) = 53.7\text{ N}

    Correct

    fk=Tcos⁡θ=85.0cos⁡(23.3∘)≈63.4 Nf_k = T\cos\theta = 85.0\cos(23.3^\circ) \approx 63.4\text{ N}

    This result propagates the swapped component and the resulting incorrect angle.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that constant velocity implies zero acceleration in both directions.

You properly accounted for the upward tension component reducing the normal force.

You used an advanced harmonic addition technique to solve the linear combination of trigonometric functions accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Component resolution error (swapped sine and cosine)

You assigned cos⁡θ\cos\theta to the vertical direction and sin⁡θ\sin\theta to the horizontal direction instead of the reverse.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Defining trigonometric components by rote rather than inspecting the right triangle formed with the reference axis: since the angle θ\theta is specified relative to the horizontal, the adjacent side is horizontal (Tx=Tcos⁡θT_x = T\cos\theta) and the opposite side is vertical (Ty=Tsin⁡θT_y = T\sin\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Axis Check
  • If an angle θ\theta is measured relative to the horizontal, the horizontal leg is adjacent (Tx=Tcos⁡θT_x = T\cos\theta) and the vertical leg is opposite (Ty=Tsin⁡θT_y = T\sin\theta).

  • Sketch the right triangle with the force vector as the hypotenuse before writing ∑Fx\sum F_x and ∑Fy\sum F_y.

Extreme Angle Sanity Check
  • As θ→0∘\theta \to 0^\circ (pulling purely horizontally), Tx→TT_x \to T and Ty→0T_y \to 0.

  • Check if cos⁡(0∘)=1\cos(0^\circ)=1 matches the direction of pure horizontal pull.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the horizontal equilibrium: Tcos⁡θ−fk=0  ⟹  fk=Tcos⁡θT\cos\theta - f_k = 0 \implies f_k = T\cos\theta.

  2. Set up the vertical equilibrium: N+Tsin⁡θ−mg=0  ⟹  N=mg−Tsin⁡θN + T\sin\theta - mg = 0 \implies N = mg - T\sin\theta.

  3. Substitute NN into the friction law: Tcos⁡θ=μk(mg−Tsin⁡θ)T\cos\theta = \mu_k (mg - T\sin\theta).

  4. Rearrange to group angle terms: cos⁡θ+μksin⁡θ=μkmgT\cos\theta + \mu_k\sin\theta = \frac{\mu_k mg}{T}.

  5. Substitute values: cos⁡θ+0.300sin⁡θ=0.300×24585.0≈0.8647\cos\theta + 0.300\sin\theta = \frac{0.300 \times 245}{85.0} \approx 0.8647.

  6. Solve for θ\theta: express as Rcos⁡(θ−ϕ)=0.8647R\cos(\theta - \phi) = 0.8647, where R=12+0.3002≈1.044R = \sqrt{1^2 + 0.300^2} \approx 1.044 and ϕ=arctan⁡(0.300)≈16.70∘\phi = \arctan(0.300) \approx 16.70^\circ, giving cos⁡(θ−16.70∘)=0.86471.044≈0.8283  ⟹  θ−16.70∘=34.07∘  ⟹  θ≈23.3∘\cos(\theta - 16.70^\circ) = \frac{0.8647}{1.044} \approx 0.8283 \implies \theta - 16.70^\circ = 34.07^\circ \implies \theta \approx 23.3^\circ (or directly using a numerical solver).

  7. Calculate friction: fk=Tcos⁡(23.3∘)=85.0×0.9184≈63.4 Nf_k = T\cos(23.3^\circ) = 85.0 \times 0.9184 \approx 63.4\text{ N}.

Final answer

θ=23.3∘\theta = 23.3^\circ, fk=63.4 Nf_k = 63.4\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing free-body diagrams with force components clearly marked alongside the reference axes.

  • Verify your resolved components by checking the limiting case θ=0∘\theta = 0^\circ before solving equations.

OverviewACEpath Teacher's Diagnosis

03 The student adds rather than subtracts the vertical tension component when solving for the normal force, writing N = m g + T sin θ.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg+Tsin⁡θN = mg + T\sin\theta

    Correct

    N+Tsin⁡θ−mg=0  ⟹  N=mg−Tsin⁡θN + T\sin\theta - mg = 0 \implies N = mg - T\sin\theta

    Because the rope pulls upward at an angle θ\theta, the vertical component Tsin⁡θT\sin\theta points upward alongside the normal force NN. In vertical equilibrium, N+Tsin⁡θ=mgN + T\sin\theta = mg, which means N=mg−Tsin⁡θN = mg - T\sin\theta.

  2. Step 2

    Tcos⁡θ=μkN=μk(mg+Tsin⁡θ)  ⟹  cos⁡θ−μksin⁡θ=μkmgTT\cos\theta = \mu_k N = \mu_k (mg + T\sin\theta) \implies \cos\theta - \mu_k\sin\theta = \mu_k \frac{mg}{T}

    Correct

    Tcos⁡θ=μk(mg−Tsin⁡θ)  ⟹  cos⁡θ+μksin⁡θ=μkmgTT\cos\theta = \mu_k (mg - T\sin\theta) \implies \cos\theta + \mu_k\sin\theta = \frac{\mu_k mg}{T}

    Your algebraic rearrangement was logically consistent with your expression for NN, but the sign error from Step 1 carried through, turning +μksin⁡θ+\mu_k\sin\theta into −μksin⁡θ-\mu_k\sin\theta.

  3. Step 3

    cos⁡θ−0.300sin⁡θ=0.8647  ⟹  1.044cos⁡(θ+16.7∘)=0.8647  ⟹  θ=17.4∘\cos\theta - 0.300\sin\theta = 0.8647 \implies 1.044\cos(\theta + 16.7^\circ) = 0.8647 \implies \theta = 17.4^\circ

    Correct

    cos⁡θ+0.300sin⁡θ=0.8647  ⟹  1.044cos⁡(θ−16.7∘)=0.8647  ⟹  θ=23.3∘\cos\theta + 0.300\sin\theta = 0.8647 \implies 1.044\cos(\theta - 16.7^\circ) = 0.8647 \implies \theta = 23.3^\circ

    Your linear combination of sine and cosine technique was mathematically sound, but it operated on the incorrect negative sign from the propagated normal force error.

  4. Step 4

    fk=Tcos⁡θ=85.0cos⁡(17.4∘)≈81.1 Nf_k = T\cos\theta = 85.0\cos(17.4^\circ) \approx 81.1\text{ N}

    Correct

    fk=Tcos⁡(23.3∘)≈63.4 Nf_k = T\cos(23.3^\circ) \approx 63.4\text{ N}

    You correctly recognized that fk=Tcos⁡θf_k = T\cos\theta at constant velocity, but substituting your propagated angle of 17.4∘17.4^\circ yielded 81.1 N81.1\text{ N} instead of 63.4 N63.4\text{ N}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that horizontal acceleration is zero and equated Tcos⁡θ=fkT\cos\theta = f_k.

You correctly related kinetic friction to the normal force via fk=μkNf_k = \mu_k N.

You executed an advanced auxiliary-angle method to solve the linear trigonometric equation with clean precision.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in vertical force balance

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the upward vertical component of tension as an additional downward load on the floor rather than an upward lifting force that relieves ground contact pressure.

REASONING PATH
Your ACEpath teacher’s suggested approach
Direction of Components
  • Forces pointing in the positive vertical direction (+y+y) add together, while forces pointing downward (−y-y) have opposite signs.

  • Draw a clear free-body diagram and write ∑Fy=N+Ty−mg=0\sum F_y = N + T_y - mg = 0 explicitly before isolating NN.

Physical Intuition Check
  • Pulling upward on an object partially lifts it, which must decrease the normal force (N<mgN < mg).

  • Whenever a pull has an upward incline, verify that N=mg−TyN = mg - T_y rather than mg+Tymg + T_y.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the vertical equilibrium condition: N+Tsin⁡θ−mg=0N + T\sin\theta - mg = 0, giving N=mg−Tsin⁡θN = mg - T\sin\theta.

  2. Substitute NN into the horizontal force balance: Tcos⁡θ=μk(mg−Tsin⁡θ)T\cos\theta = \mu_k(mg - T\sin\theta).

  3. Rearrange to collect trigonometric terms: cos⁡θ+μksin⁡θ=μkmgT=0.300×24585.0≈0.8647\cos\theta + \mu_k\sin\theta = \frac{\mu_k mg}{T} = \frac{0.300 \times 245}{85.0} \approx 0.8647.

  4. Apply the harmonic identity: 12+0.3002cos⁡(θ−tan⁡−1(0.300))=1.044cos⁡(θ−16.7∘)=0.8647\sqrt{1^2 + 0.300^2}\cos(\theta - \tan^{-1}(0.300)) = 1.044\cos(\theta - 16.7^\circ) = 0.8647.

  5. Solve for the angle: θ−16.7∘=cos⁡−1(0.8282)=34.1∘  ⟹  θ=34.1∘−10.8∘=23.3∘\theta - 16.7^\circ = \cos^{-1}(0.8282) = 34.1^\circ \implies \theta = 34.1^\circ - 10.8^\circ = 23.3^\circ.

  6. Compute the friction force: fk=Tcos⁡θ=85.0cos⁡(23.3∘)≈63.4 Nf_k = T\cos\theta = 85.0\cos(23.3^\circ) \approx 63.4\text{ N}.

Final answer

θ=23.3∘\theta = 23.3^\circ, fk=63.4 Nf_k = 63.4\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a free-body diagram showing both NN and Tsin⁡θT\sin\theta pointing upward before writing the vertical equilibrium equation.

  • Perform a quick physical sanity check: confirm whether the applied force lifts the object (N<mgN < mg) or pushes it into the surface (N>mgN > mg).

Lock it in

Similar question

01

A 15.0 kg15.0\text{ kg} crate is pushed along a horizontal floor by a downward-angled force P=50.0 NP = 50.0\text{ N} inclined at 30.0∘30.0^\circ below the horizontal. If μk=0.250\mu_k = 0.250 and g=9.80 m/s2g = 9.80\text{ m/s}^2, find the normal force NN and the kinetic frictional force fkf_k.

Answer

N=mg+Psin⁡(30.0∘)=(15.0)(9.80)+50.0(0.500)=147+25.0=172 NN = mg + P \sin(30.0^\circ) = (15.0)(9.80) + 50.0(0.500) = 147 + 25.0 = 172\text{ N}; fk=μkN=0.250×172 N=43.0 Nf_k = \mu_k N = 0.250 \times 172\text{ N} = 43.0\text{ N}.

02

A 20.0 kg20.0\text{ kg} trunk is pulled across a level floor at constant velocity by a rope inclined at 37.0∘37.0^\circ above the horizontal. The coefficient of kinetic friction is μk=0.400\mu_k = 0.400. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the tension TT in the rope.

Answer

Horizontal: Tcos⁡(37.0∘)=μkNT \cos(37.0^\circ) = \mu_k N. Vertical: N=mg−Tsin⁡(37.0∘)N = mg - T \sin(37.0^\circ). Substitute: Tcos⁡(37.0∘)=μk(mg−Tsin⁡(37.0∘))  ⟹  T(cos⁡(37.0∘)+μksin⁡(37.0∘))=μkmgT \cos(37.0^\circ) = \mu_k (mg - T \sin(37.0^\circ)) \implies T (\cos(37.0^\circ) + \mu_k \sin(37.0^\circ)) = \mu_k mg. With cos⁡(37.0∘)≈0.7986\cos(37.0^\circ) \approx 0.7986 and sin⁡(37.0∘)≈0.6018\sin(37.0^\circ) \approx 0.6018: T(0.7986+0.400×0.6018)=0.400×196  ⟹  T(1.039)=78.4  ⟹  T≈75.4 NT (0.7986 + 0.400 \times 0.6018) = 0.400 \times 196 \implies T(1.039) = 78.4 \implies T \approx 75.4\text{ N}.

03

A block of mass mm is pulled along a horizontal surface with kinetic friction coefficient μk\mu_k by an inclined tension TT. Prove that the pulling angle θ\theta that minimizes the tension required to maintain constant speed satisfies tan⁡θ=μk\tan\theta = \mu_k, and state whether this angle increases or decreases NN relative to pulling horizontally.

Answer

Equilibrium gives T=μkmgcos⁡θ+μksin⁡θT = \frac{\mu_k mg}{\cos\theta + \mu_k \sin\theta}. To minimize TT, maximize D(θ)=cos⁡θ+μksin⁡θD(\theta) = \cos\theta + \mu_k \sin\theta. Setting dDdθ=−sin⁡θ+μkcos⁡θ=0\frac{dD}{d\theta} = -\sin\theta + \mu_k \cos\theta = 0 yields tan⁡θ=μk\tan\theta = \mu_k. Since θ>0\theta > 0, Tsin⁡θ>0T \sin\theta > 0, so N=mg−Tsin⁡θ<mgN = mg - T \sin\theta < mg; pulling at this optimal upward angle reduces the normal force and therefore reduces friction.

Loading workspace…