Resources

A helium recovery capsule is ascending strictly vertically at a constant upward cruise velocity of vc=4.90 m/sv_c = 4.90\text{ m/s}. When the capsule is at an altitude of h0=58.8 mh_0 = 58.8\text{ m} above the open ocean, an external ballast beacon is jettisoned with zero relative velocity to the capsule. The beacon then moves exclusively under gravitational acceleration g=9.80 m/s2g = 9.80\text{ m/s}^2 downward. Determine: (a) the maximum height ymaxy_{\text{max}} reached by the ballast beacon above sea level, and (b) the total elapsed time tsplasht_{\text{splash}} from detachment until the beacon strikes the ocean surface.

Answer and steps

Final answer

(a) ymax=60.0 my_{\text{max}} = 60.0\text{ m}; (b) tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

Steps

Part (a): Maximum Height Above Sea Level

  1. Identify the initial conditions: Because the ballast beacon is jettisoned with zero relative velocity from an ascending capsule, it inherits the capsule's velocity at that instant:

    • Initial position: y0=58.8 my_0 = 58.8\text{ m}
    • Initial velocity: v0=+4.90 m/sv_0 = +4.90\text{ m/s} (upward)
    • Acceleration: a=−g=−9.80 m/s2a = -g = -9.80\text{ m/s}^2 (downward)

    Common Pitfall: A frequent mistake is assuming the beacon starts from rest (v0=0v_0 = 0) simply because it was "dropped" or "released." Due to inertia, any object released from a moving vehicle retains the vehicle's velocity at the moment of release.

  2. Calculate the additional height during the upward rise: At the highest point of the trajectory, the vertical velocity momentarily reaches zero (v=0v = 0). Using the kinematic relation v2=v02+2aΔyv^2 = v_0^2 + 2a\Delta y: 0=v02−2g Δyrise0 = v_0^2 - 2g\,\Delta y_{\text{rise}} Δyrise=v022g=(4.90 m/s)22(9.80 m/s2)=24.0119.60 m=1.225 m\Delta y_{\text{rise}} = \frac{v_0^2}{2g} = \frac{(4.90\text{ m/s})^2}{2(9.80\text{ m/s}^2)} = \frac{24.01}{19.60}\text{ m} = 1.225\text{ m}
  3. Determine the maximum altitude: ymax=y0+Δyrise=58.8 m+1.225 m=60.025 m≈60.0 my_{\text{max}} = y_0 + \Delta y_{\text{rise}} = 58.8\text{ m} + 1.225\text{ m} = 60.025\text{ m} \approx 60.0\text{ m}

Part (b): Total Elapsed Time Until Impact

  1. Set up the vertical displacement equation: Taking the ocean surface as the reference line (y=0 my = 0\text{ m}), the final vertical position is y=0 my = 0\text{ m}. The net displacement Δy\Delta y from the point of release is: Δy=y−y0=0−58.8 m=−58.8 m\Delta y = y - y_0 = 0 - 58.8\text{ m} = -58.8\text{ m}
  2. Apply the displacement kinematic formula: Δy=v0t−12gt2\Delta y = v_0 t - \frac{1}{2}gt^2 −58.8=4.90t−12(9.80)t2-58.8 = 4.90t - \frac{1}{2}(9.80)t^2 −58.8=4.90t−4.90t2-58.8 = 4.90t - 4.90t^2
  3. Solve the quadratic equation: Divide the entire equation by 4.904.90: −12=t−t2-12 = t - t^2 t2−t−12=0t^2 - t - 12 = 0 Factoring the quadratic gives: (t−4)(t+3)=0(t - 4)(t + 3) = 0

    Since physical elapsed time must be positive (t>0t > 0): tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that the jettisoned beacon inherits the upward velocity of the ascending capsule, assuming it is dropped from rest.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Since the beacon is released with zero relative velocity, v0=0.\text{Since the beacon is released with zero relative velocity, } v_0 = 0.

    Correct

    v0=vc+vrel=4.90 m/s+0=+4.90 m/sv_0 = v_c + v_{\text{rel}} = 4.90\text{ m/s} + 0 = +4.90\text{ m/s}

    You interpreted zero relative velocity to the capsule as zero velocity relative to the ground. Because the capsule is ascending at 4.90 m/s4.90\text{ m/s}, the beacon inherits that upward velocity when released.

  2. Step 2

    ymax=h0=58.8 my_{\text{max}} = h_0 = 58.8\text{ m}

    Correct

    ymax=h0+v022g=58.8 m+(4.90 m/s)22(9.80 m/s2)=60.0 my_{\text{max}} = h_0 + \frac{v_0^2}{2g} = 58.8\text{ m} + \frac{(4.90\text{ m/s})^2}{2(9.80\text{ m/s}^2)} = 60.0\text{ m}

    Because your initial velocity was set to zero, you concluded that the beacon never rose above its release point. With the upward velocity v0=4.90 m/sv_0 = 4.90\text{ m/s}, it continues rising until its upward velocity reaches zero.

  3. Step 3

    y(t)=h0−12gt2=0  ⟹  58.8−4.90t2=0  ⟹  t2=58.84.90=12  ⟹  tsplash=12≈3.46 sy(t) = h_0 - \frac{1}{2}gt^2 = 0 \implies 58.8 - 4.90t^2 = 0 \implies t^2 = \frac{58.8}{4.90} = 12 \implies t_{\text{splash}} = \sqrt{12} \approx 3.46\text{ s}

    Correct

    y(t)=h0+v0t−12gt2=0  ⟹  58.8+4.90t−4.90t2=0  ⟹  t2−t−12=0  ⟹  tsplash=4.00 sy(t) = h_0 + v_0 t - \frac{1}{2}gt^2 = 0 \implies 58.8 + 4.90t - 4.90t^2 = 0 \implies t^2 - t - 12 = 0 \implies t_{\text{splash}} = 4.00\text{ s}

    You solved your simplified free-fall quadratic equation correctly, but omitting the linear term v0tv_0 t propagated the initial velocity error into your final splashdown time.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the ground level as the target position y=0 my=0\text{ m}.

You accurately substituted g=9.80 m/s2g = 9.80\text{ m/s}^2 and solved the quadratic expression.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inherited initial velocity in relative motion

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated relative velocity with respect to a moving vehicle (vrel=0v_{\text{rel}} = 0) with absolute velocity in the Earth reference frame (v0=vcarrierv_0 = v_{\text{carrier}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Frame Transfer
  • An object released or dropped from a moving carrier always inherits the instantaneous velocity of the carrier: vground=vcarrier+vrelv_{\text{ground}} = v_{\text{carrier}} + v_{\text{rel}}.

  • Whenever a problem states an object is dropped or released with zero relative speed, identify the carrier's velocity vector and use it as v0v_0 for your kinematic equations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the initial velocity relative to the ocean surface: v0=+4.90 m/sv_0 = +4.90\text{ m/s}.

  2. Calculate the extra rise height: Δy=v022g=4.9022(9.80)=1.225 m\Delta y = \frac{v_0^2}{2g} = \frac{4.90^2}{2(9.80)} = 1.225\text{ m}, giving ymax=58.8+1.225=60.0 my_{\text{max}} = 58.8 + 1.225 = 60.0\text{ m}.

  3. Write the vertical position equation including v0v_0: 0=58.8+4.90t−4.90t20 = 58.8 + 4.90t - 4.90t^2.

  4. Divide by 4.904.90 and factor: t2−t−12=(t−4)(t+3)=0t^2 - t - 12 = (t - 4)(t + 3) = 0. Since time is positive, tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}.

Final answer

(a) ymax=60.0 my_{\text{max}} = 60.0\text{ m}; (b) tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review inertial reference frames to reinforce how released objects inherit carrier motion.

  • Practice writing the complete kinematic position function y(t)=y0+v0t−12gt2y(t) = y_0 + v_0 t - \frac{1}{2}gt^2 before deciding whether any terms are zero.

OverviewACEpath Teacher's Diagnosis

02 The student calculates only the additional height above the release altitude rather than the total maximum height above sea level.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v2=v02−2gΔy=0  ⟹  Δy=v022g=(4.90)22×9.80=1.225 mv^2 = v_0^2 - 2g\Delta y = 0 \implies \Delta y = \frac{v_0^2}{2g} = \frac{(4.90)^2}{2 \times 9.80} = 1.225\text{ m}

  2. Step 2

    ymax=1.23 my_{\text{max}} = 1.23\text{ m}

    Correct

    ymax=h0+Δyrise=58.8 m+1.225 m≈60.0 my_{\text{max}} = h_0 + \Delta y_{\text{rise}} = 58.8\text{ m} + 1.225\text{ m} \approx 60.0\text{ m}

    You reported only the rise Δy=1.23 m\Delta y = 1.23\text{ m} above the release altitude instead of adding the initial altitude h0=58.8 mh_0 = 58.8\text{ m} to get the total height above sea level.

  3. Step 3

    −58.8=4.90t−(12)(9.80)t2  ⟹  4.90t2−4.90t−58.8=0  ⟹  t2−t−12=0  ⟹  (t−4)(t+3)=0-58.8 = 4.90t - \left(\frac{1}{2}\right)(9.80)t^2 \implies 4.90t^2 - 4.90t - 58.8 = 0 \implies t^2 - t - 12 = 0 \implies (t - 4)(t + 3) = 0

  4. Step 4

    tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that an object released from an ascending vessel inherits the vessel's vertical velocity.

You accurately calculated the upward displacement from the point of release using work-energy kinematics.

You set up and factored the full quadratic displacement equation correctly to find the impact time.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Initial Reference Height

You solved for the rise relative to the release point but did not add the initial altitude of 58.8 m58.8\text{ m} to report altitude above sea level.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing displacement relative to the release point (Δy=y−y0\Delta y = y - y_0) with absolute coordinate position (y=y0+Δyy = y_0 + \Delta y) measured from a chosen ground or sea-level reference datum.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish Displacement from Position
  • Kinematic formulas like v2=v02+2aΔyv^2 = v_0^2 + 2a\Delta y give displacement Δy\Delta y, not the final coordinate yy.

  • Always write y=y0+Δyy = y_0 + \Delta y explicitly whenever the problem asks for height above a specific reference level (such as sea level or ground).

Verify Reference Level at the Start
  • Identify whether the baseline is y=0y = 0 (ground/sea level) or the launch height y=y0y = y_0.

  • Annotate your sketch with both y0y_0 and the reference datum before writing down equations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ymax=y0+Δyrisey_{\text{max}} = y_0 + \Delta y_{\text{rise}}

  2. ymax=58.8 m+1.225 m=60.025 m≈60.0 my_{\text{max}} = 58.8\text{ m} + 1.225\text{ m} = 60.025\text{ m} \approx 60.0\text{ m}

Final answer

(a) ymax=60.0 my_{\text{max}} = 60.0\text{ m}; (b) tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • In your sketch, draw a clear coordinate axis with y=0y = 0 at the reference datum (e.g., ground or sea level) and label the initial height y0y_0.

  • Whenever a kinematic formula yields Δy\Delta y, remind yourself that this is only the change in height; add y0y_0 to find the final elevation.

OverviewACEpath Teacher's Diagnosis

03 The student treats downward displacement as positive while keeping the upward velocity positive, leading to an incorrect sign in the position equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v2=v02−2g(ymax−h0)=0  ⟹  ymax=58.8+(4.90)22×9.80=60.0 mv^2 = v_0^2 - 2g(y_{\text{max}} - h_0) = 0 \implies y_{\text{max}} = 58.8 + \frac{(4.90)^2}{2 \times 9.80} = 60.0\text{ m}

  2. Step 2

    Δy=v0t+(12)gt2  ⟹  58.8=4.90t+4.90t2\Delta y = v_0 t + \left(\frac{1}{2}\right)gt^2 \implies 58.8 = 4.90t + 4.90t^2

    Correct

    Δy=v0t−12gt2  ⟹  −58.8=4.90t−4.90t2\Delta y = v_0 t - \frac{1}{2}gt^2 \implies -58.8 = 4.90t - 4.90t^2

    You assigned positive signs to both the upward initial velocity (v0=+4.90 m/sv_0 = +4.90\text{ m/s}) and the downward acceleration/displacement (g=9.80 m/s2g = 9.80\text{ m/s}^2, Δy=58.8 m\Delta y = 58.8\text{ m}). If upward is positive, the displacement to the water is Δy=−58.8 m\Delta y = -58.8\text{ m} and the acceleration is a=−9.80 m/s2a = -9.80\text{ m/s}^2.

  3. Step 3

    4.90t2+4.90t−58.8=0  ⟹  t2+t−12=0  ⟹  (t+4)(t−3)=04.90t^2 + 4.90t - 58.8 = 0 \implies t^2 + t - 12 = 0 \implies (t+4)(t-3) = 0

    Correct

    4.90t2−4.90t−58.8=0  ⟹  t2−t−12=0  ⟹  (t−4)(t+3)=04.90t^2 - 4.90t - 58.8 = 0 \implies t^2 - t - 12 = 0 \implies (t-4)(t+3) = 0

    Your algebraic factoring was carried out correctly for your written equation, but it inherited the sign error from the previous step.

  4. Step 4

    tsplash=3ANCY3.00 st_{\text{splash}} = 3 ANCY 3.00\text{ s}

    Correct

    tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

    Selecting the positive root gave t=3.00 st = 3.00\text{ s} due to the sign error in the kinematic equation.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the jettisoned beacon inherits the upward initial velocity of the capsule (v0=+4.90 m/sv_0 = +4.90\text{ m/s}).

You applied the work-energy/kinematic relation accurately to find the peak altitude of 60.0 m60.0\text{ m}.

You demonstrated strong algebraic skills by correctly factoring the quadratic equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inconsistent Sign Convention

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You did not establish a single consistent coordinate axis for vectors in 1D kinematics. When defining upward as positive for initial velocity (+4.90 m/s+4.90\text{ m/s}), downward vectors such as acceleration (−9.80 m/s2-9.80\text{ m/s}^2) and final displacement from the launch height (−58.8 m-58.8\text{ m}) must take negative signs.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define Axis Direction First
  • Before substituting values into Δy=v0t+12at2\Delta y = v_0 t + \frac{1}{2}at^2, declare either upward or downward as the positive direction.

  • If upward is positive, set v0>0v_0 > 0, a=−g=−9.80 m/s2a = -g = -9.80\text{ m/s}^2, and Δy=yfinal−yinitial=0−58.8=−58.8 m\Delta y = y_{\text{final}} - y_{\text{initial}} = 0 - 58.8 = -58.8\text{ m}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Establish upward as the positive vertical direction: y0=58.8 my_0 = 58.8\text{ m}, y=0 my = 0\text{ m}, so Δy=−58.8 m\Delta y = -58.8\text{ m}.

  2. Identify initial velocity and acceleration: v0=+4.90 m/sv_0 = +4.90\text{ m/s}, a=−g=−9.80 m/s2a = -g = -9.80\text{ m/s}^2.

  3. Substitute into the position formula: −58.8=4.90t−12(9.80)t2  ⟹  −58.8=4.90t−4.90t2-58.8 = 4.90t - \frac{1}{2}(9.80)t^2 \implies -58.8 = 4.90t - 4.90t^2.

  4. Rearrange into standard quadratic form: 4.90t2−4.90t−58.8=0  ⟹  t2−t−12=04.90t^2 - 4.90t - 58.8 = 0 \implies t^2 - t - 12 = 0.

  5. Factor the quadratic expression: (t−4)(t+3)=0(t - 4)(t + 3) = 0.

Final answer

tsplash=4.00 st_{\text{splash}} = 4.00\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always draw a simple vertical axis showing the origin (y=0y = 0) and an arrow indicating whether upward or downward is positive.

  • List all vector quantities (v0v_0, aa, Δy\Delta y) with their explicit signs before writing down kinematic formulas.

Lock it in

Similar question

01

A weather balloon ascends vertically at a steady 5.0 m/s5.0\text{ m/s}. At an altitude of 40.0 m40.0\text{ m}, an instrument package is released with zero relative velocity. Taking g=10.0 m/s2g = 10.0\text{ m/s}^2, find the maximum height reached by the package above the ground.

Answer

ymax=41.25 my_{\text{max}} = 41.25\text{ m}. The package inherits initial upward velocity v0=5.0 m/sv_0 = 5.0\text{ m/s}. The rise distance is Δy=v022g=2520=1.25 m\Delta y = \frac{v_0^2}{2g} = \frac{25}{20} = 1.25\text{ m}. Therefore, ymax=40.0 m+1.25 m=41.25 my_{\text{max}} = 40.0\text{ m} + 1.25\text{ m} = 41.25\text{ m}.

02

An open construction elevator descends vertically at a constant speed of 4.0 m/s4.0\text{ m/s}. When it is 24.0 m24.0\text{ m} above the ground, a bolt falls off the platform. Using g=9.8 m/s2g = 9.8\text{ m/s}^2, how long does it take for the bolt to hit the ground?

Answer

t≈1.84 st \approx 1.84\text{ s}. The bolt inherits downward velocity v0=−4.0 m/sv_0 = -4.0\text{ m/s}. The displacement equation is −24.0=−4.0t−4.9t2-24.0 = -4.0t - 4.9t^2, which rearranges to 4.9t2+4.0t−24.0=04.9t^2 + 4.0t - 24.0 = 0. Solving with the quadratic formula yields t=−4.0+16+470.49.8≈1.84 st = \frac{-4.0 + \sqrt{16 + 470.4}}{9.8} \approx 1.84\text{ s}.

03

A rescue helicopter ascends at a constant rate of 10.0 m/s10.0\text{ m/s}. A flare is fired vertically upward from the helicopter at 15.0 m/s15.0\text{ m/s} relative to the helicopter when the helicopter is 120.0 m120.0\text{ m} above the sea. Using g=10.0 m/s2g = 10.0\text{ m/s}^2, determine the flare's total flight time until it hits the sea.

Answer

t=8.0 st = 8.0\text{ s}. The ground velocity of the flare is v0=vcopter+vrel=10.0+15.0=25.0 m/sv_0 = v_{\text{copter}} + v_{\text{rel}} = 10.0 + 15.0 = 25.0\text{ m/s}. Using Δy=v0t−12gt2\Delta y = v_0 t - \frac{1}{2}gt^2: −120=25t−5t2  ⟹  5t2−25t−120=0  ⟹  t2−5t−24=0-120 = 25t - 5t^2 \implies 5t^2 - 25t - 120 = 0 \implies t^2 - 5t - 24 = 0. Factoring gives (t−8)(t+3)=0(t - 8)(t + 3) = 0, so t=8.0 st = 8.0\text{ s}.

Loading workspace…